Tender For Renovation Work In Zila Parishad Bhawan Kota - 1 Providing and fixing 12.5 mm thick tapered edge gypsum board conforming to IS 2095- Part I at all height false ceiling including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanised in accordance with zinc coating of grade 350 as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Engineer in Charge but excluding the cost of painting. 2 Providing and fixing wood panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled and glazed shutter 25 mm to 40 mm thickNigeria wood Grade I 3 IS 710- 1976 marked 19 mm thick commerical ply 4 IS 710- 1976 marked 12 mm thick commerical ply 5 Providing & Fixing mica of approved make for inner/outer side of shutters with fevicol & nails completeas per approved by engineer in charge.0.8mm thick mica 6 Providing& fixing door, window, chowkhats and other frames, including antitermite treatment, M.S. flat, hold fasts of size 250 x 40 x 3mm fixed with M.S. bolt 5mm dia 50mm long duly embedded in cement concrete M-15 grade :Ghana teak wood Grade - I. 7 25mm thick wooden planking, tongued and grooved in flooring including fixing with iron screws complete (Lower frame to be paid extra) with :First class Teak wood. 8 Providing and laying wooden flooring with a direct laminated surface treated with aluminum oxide on top ofa high-density fiber board with a density of 850 Kg./per Mtr. having a click system tongue and groove joint to secure a long lasting joint. The planks are or termite resistant and water protected with both side lamination Wooden flooring Planks of size 1208 x 194 x 8 mm / 1215x294x8 mm (8mm thick laminated floor class of use 23/31 having a wear resistance level of AC-3 , impact resistance > 9mm, moisture resistance 3-10% as per (EN-424, EN – 438 EN – 425 EN – 417 – 2)or PREN 3329 complete in all respect as per direction of EI 9 Providing and laying of skirting 89 mm wide having both side laminations with moulding in upper side with matching of floor fixing with nails and screws & fevicol complete in all respect as per direction of EI. 10 Providing and laying transaction/adaptation profile with fixing of nails, screws & fevicol complete in all respect as per direction of EI. 11 Anti termite treatment of floor using Imidacloprid 30.5% EC non repellent, odorless, low dose, environmentally safe terniticide with rapid action non corrosive stain free, by drilling 12mm diameter holes 300mm apart injecting the emulsion as per specification and plugging with cement mortar 1:2 ( 1 cement : 2 coarse sand) in the whole floor area DPE 12mm dia termitube system with required number of junction boxes are to be installed. The termitube will run all along the perimeter wall both inside and outside. In the middle area the termitube to be installed at an interval of 1.00 Mtr. or less both ways as required with sufficient number of junction boxes to pump the emulsion. After successful testing of termitube, pesticide emulsion of imidacloprid 30.5% EC mixed with water in the ration of 1:474 will be pumped by a motorized spray pump from the junction box in specified manner. The plinth area of the area treated will be measured for payment. 12 Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3mm thick water proofing membrane, black finished reinforced with glass fibre matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 Itr/sq.mt. by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ltr and viscosity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under Joint strength in longitudinal and transverse direction at 23°C as 650/450N/5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D-5147. The laying of membrane shall be got done through the authorized applicator of the manufacturer of membrane.3 mm thick 13 Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils 14 Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in:Cement Mortar 1:6 ( 1-Cement : 6-Sand). 15 Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M10 grade Nominal Mix1: 3: 6 (1 cement : 3 coarse sand : 6 graded stoneaggregate 20mm nominal size). 16 Providing and laying in position specified grade ofcement concrete forall RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers( if required) excluding the cost of centering, shuttering and reinforcement. 20 grade Nominal Mix / Design Mix 17 Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for :Suspended floors, roofs, landings, staircases, balconies, girders, cantilevers, bands, coping bed plates,anchorblocks,sills,chhajjas,lintel,beam, plinth beam etc. 18 Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete up to floor Three level. Thermo-mechanically Treated bars (Conforming of relevent IS code) 19 Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in :Cement mortar 1 : 6 (1 cement : 6 coarse sand) 20 Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish :20mm thick. 21 Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M20 grade Nominal Mix1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stoneaggregate 20mm nominal size). 22 Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide 23 Extra if square,rectangular hollow tubelarsections are used or grill made by flats only 24 Painting with synthetic enamel paint of approved brand and manufacture togive an even shade : Two or more coats on new work 25 Painting exterior surface ofWallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty,etc complete in all respect including scaffolding and safety provisionOld Work 26 Providing and applying superior quality emulsion for wall painting with Velvet touch/Royal paint etc of approved brand and manufacture to give an even shade with putty and preparation of surface applying with the help of paint roller the work complete in all respect as per direction of Engineer-in-charge.New Work Three or More coat 27 Providing & Fixing of anti skid high strength, high finish, coloured Tile/Interlocking flooring having thickness 60 mm over prepared surface with base of 25 mm thick cement and mortar 1:4 as per approved colour, design & drawing including all erspect complete. (the design of paving blocks shall be decided by Engineer-in-charge) 28 Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete.Jhunjhunu / Jalore (Red/Choclate/Black/Pink Colour)Above 3601 Cm2 Slabs 29 P & F Stone cladding/Flooring works dressed bansi paharpur stone 25mm thick in traditional style used in cladding/Flooring with pattern over 25 to 50 mm thick base in CM 1:6 including pointing with cement mortar 1:2 (cement : 2 stone dust) matche the shade of stone with joint thickness upto 1.5mm as per direction of engineer-in-charge. 30 Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar. 31 Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge: In cement mortar. 32 Dismantling doors, windows and clearstory windows steel or wood shutter including chowkhats and holdfasts etc. complete and stacking within 50 meters lead:Of area 3 square meter and below. 33 Transpotation of excavated earth from site incliding, loading & unloading lead 5 Km 34 Random rubble dry stone Kharanja under floor. 35 Half brick masonry in Superstructure , above plinth level upto floor Vlevelusing bricks of designation 75 Cement mortar 1 : 6 (1 cement : 6 coarse sand) 36 Providing and fixing of uPVC casement fixed windows or ventilators manufactured in ISO 9001:2000 & 14001:2004 certified company. Frame : Made from the Extruded uPVC Window Profile Section of size 60 x 60mm having outer wall thickness of 2.25mm (+/- 0.2mm) and 3 box multi-chamber construction, White in finish, duly reinforced with 1.2mm thick G/J/U/O TYPE GI section. All the four corners shall be mitered cut & thermal welded so as to form window frame. Frame shall be milled with drain and air equalizer hole in order to be water tight and for drainage of accumulated water, if any, to outer side. Fix Mullion made of 76 x 60mm uPVC Profile Section with steel reinforcement shall be provided in windows as per the requirement. Frame shall have ‘O’ type EPDM gasket fitted in in-built groove of frame profile for proper air & sound insulation of the shutter. Glazing bead of size 34 x 20mm with ‘K’ & ‘O’ type inner and outer EPDM weather seal gaskets alongwith 5mm thick ISI make plain float glass.All welding joints of frame and shutter shall be cleaned and milled with the CNC mechanism to provide uniform grooved finish on all visible joints. Hardware : Installation at Site : Complete window is to be installed on site with 10 x 100mm fastners with white cap in existing pre-finished wall cut-out cemented to glass level plane at all height & width and silicon glue is applied to fill up the crevices between wall and window frame. Complete in all respect as per the drawing and specifications and direction of engineer-in-charge. 37 Providing and fixing of uPVC Sliding windows: Frame Made from the Extruded uPVC Window Profile Section of size 106w x 50h mm having outer wall thickness of 2.5mm (+/- 0.2mm) and 3 box multi-chamber construction, Laminated (colour) finish, duly reinforced with 1.2 mm thick GI section. Frame shall have three track configuration, two for sliding of window shutter and one for mosquito mesh shutter. Vertical member of frame which bears the sliding shutter load shall have aluminium rail/track for smooth sliding of shutter rollers. All the four corners shall be mitered cut & thermal welded so as to form window frame. Frame shall be milled with drain and air equalizer hole in order to be water tight and for drainage of accumulated water, if any, to outer side. Shutter : The shutter of sliding window shall be made of 39w x 69h mm Extruded 3 box multi- chamber uPVC Window Profile Section of laminated ( colour) having outer wall thickness of 2.5mm (+/- 0.2mm) provided with reinforcement of 1.5mm thick GI section duly mitered cut & thermal welded at all corners and fitted with uPVC glazing bead of size 22 x 20 mm with inner and outer co-extruded EPDM/TPE-Eweather seal gaskets alongwith 6mm thick ISI make plain float glass. Mesh shutter shall be made of 39w x 69h mm Extruded 3 box multi-chamberUPVC Window profile section of laminated ( colour) having outer wall thickness of 2.5mm (+/- 0.2mm) provided with reinforcement of 1.5 mm thick GI section duly mitered cut & thermal welded at all corners and fitted with nylon/polymer mesh and rollers/pully. 38 Providing and fixing stainless steel railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).Grade 304 39 P & F 1st qualityHeavy Duty Vitrified Polished Digital tiles on floor, skirting and steps etc.in different sizes (thickness minimum 10mm) with water absortion less than or equal 0.08% and conforming to IS 15622 of approved make in all colour and shade, laid with 20 mm thick CM 1: 4 including grounting the joints with white cement and matching pigment etc complete.Size600 mm X 1200 mm 40 P & F 1st quality Heavy Duty Vitrified glazed MAT tiles on floor, skirting and steps etc.in different sizes (thickness minimum 10mm) with water absortion less than or equal 0.08% and conforming to IS 15622 of approved make in all colour and shade, laid with 20 mm thick CM 1: 4 including grounting the joints with white cement and matching pigment etc complete.Size600 mm X 1200 mm 41 P & F Indian type white glazed vitreous china 1st quality W.C. orissa pan (IS :2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor:Size 580x440mm. 42 P & F White Vitreous China Double Syphonic European W.C. (I.S:2556Mark) with mounted W.V.C. flushing cistern of (IS : 2556 Mark) of 10 litre capacity complete with all necessary internal fittings including cutting and making good the wall and floor. 43 P & F water closet Seat Covers with brass hinges complete : -do- White. 44 P & F C.P. lugs for toilet seat cover. 45 P & F lst quality WVC Urinal (IS:2556 mark) with 25mm dia G.I. waste pipe, dome waste couplings, concealed iron brackets or screws etc complete.Flat Back (large) or half stall size 610x400x80mm. 46 P&FC.P.brassUrinalFlushPipeset complete with flanged brackets of approved make.For 1 Urinal 47 P & F C.P. brass Urinal Spreader for stall urinal of approved make. 48 P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make, P.V.C Waste pipe with PVC nut 32 mm complete including cutting & making good the wall :Size 610 mm x 510 mm 49 P& F waste Coulping with fittings of approved quality /make:C.P Brass 32 mm dia 50 P & F Bevelled edge Mirror/mirror with teak wood lipping around of special glass of approved make as per direction of Engineer-in-charge complete with 6mm thick commercial ply base fixed to wooden screws & washers. Size 600 x 450mm x 4 mm thick 51 P & F Grating of approved quality/make:Stainless Steel Sheet size 125mm dia. Heavy Quality of approved make 52 P & F Extension Pipe for bib cocks of approved quality/make.(-do-) 150 X 15mm. 53 P & F Jet spray for water closet with C.P. Copper Tube flange of approved make.Providing & fixing C.P.flange for 15mm dia taps. 54 P & F Jet spray for water closet with C.P. Copper Tube flange of approved make.Providing & fixing C.P.flange for 15mm dia taps. 55 P & F Bib Cock (IS : 8931 Mark), Superior quality of approved make:(-do-) Elbow-action, 15mm nominal bore. 56 P & F Ball Cock (IS :1703 Mark) with Rod& P.V.C. Ball complete 57 P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc. ---do--- with 37 cm long pipe and nut. 58 P & F Full-way Valve (IS:778 Mark) or wheel valve of approved make :(-do-) 32mm nominal bore. 59 P & F PVC Storage Tank ISI Marked (IS : 12701) indicating theBIS license No),of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 1000 (-do-) 60 Hoisting Charges for each floor :For items 2.26.5 to 2.26.8 61 Providing and fixingSuperior quality CP Brassfittings of approved make as per direction of Engineer-in-chargeLong body Bib Cock 15 mm nominal size 62 P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant.110 mm dia 63 160 mm dia 64 P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant:Coupler (socket)110mm dia 65 160 mm dia 66 Construction of manhole in all type of soil inner size 90 X 60 Cm. 300 mm thick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5:10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring, making channels, 80mm thick stone slab covering with 40mm thick M-15 grade C.C. flooring, Cement cover with frame of 450mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead. 67 Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes Type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /make75 mm dia 68 110 mm dia 69 Providing and Fixing Unplasticized Poly Vinyl Chloride (UPVC) SWR Pipes fittings type B for sciland waste discharge system (IS:13592 : 1992 Marked) of approved quality /makeCoupler75mm dia 70 110mm dia 71 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1 metre spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (Internal work Exposed on wall)25 mm nominal size 72 32mm nominal size 73 Supply & installation Conference Table size 1000L*6000*750H in mm, Table Top made of 36mm Thick Particle board Round Post form top With 2mm Thick PVC Edge banded Finish With As Per Approved Laminate Shade, Connection Tops of conference table made of MDF Board of size 600W x 600D x 25mm Round postform Pasted With 0.4mm Thick black PVC Membrane on Board, Gable - Ends of the table Made Of 25mm Thick PLPB twin Board designed with similar to the photograph, Modesty Panel Prime Quality 25mm Thick 718mm High PLPB Board Supported To Top & Gable ends, 7mm High PVC Buffers Screw With Gable-end, PVC Wire manager provide on top, 18mm thick PLPB cable tray should be provided below top, All Wooden Panels. Gables & Modesty Fix Joints With Minifix Dowels &Other Fitting EquipmentAll Wooden Panels Prime Quality Board With ISI Marked. IS:12823:1990. The product should bear IGBC Green Pro certificate for product category. And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design. As Direction by Engineer-in-Charge 74 Supply & installation of High Back Revolving Chair, Overall Dimension:- 710W ±10 x 710D ±10 x 1210H ±10 mm,Seat of High back chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery on Seat , Used PU Moulded foam on Seat of D-45 kg/m3 , Back of High back chair is made of Injection moulded PP material structure upholstered with Mesh fabric , Adjustable Lumber support upholstered with fabric ,Headrest on back Upholstered with Fabric , Seat Size:- 460W ±10 x 455D ±10 x 70Thick. ±5 mm , Back Size:- 470W ±10 x 710H ±10,Mechanism:- Syncro Tilt Mechanism ,Gaslift:- Lift -Used gaslift of 90 mm ,Armrest:- PU Padded adjustable armrest , armrest fixed with Seat,Chair Base & Wheels:- Metal chrome plated Chair Base , base consists of 5 prongs with 650±5 mm pitch circle diameter, 50mm Dia. Black Nylon - Twin Wheel Pin castor .The product should bear IGBC Green Pro certificate for product category.And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design. 75 Supply & installation Medium Back Revolving Chair, Overall Dimension:- 720W ±10 x 720D ±10 x 1070H ±10 mm,Seat of Medium back chair is made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery on Seat , Used PU Moulded foam on Seat ofD-45 kg/m3 , Back of High back chair is made of Injection moulded PP material structure upholstered with Mesh fabric , Seat and back connected through metal powder coated plate, Adjustable Lumber support upholstered with fabric , Seat Size:- 470W ±10 x 470D ±10 x 70Thick. ±5 mm , Back Size: 525W ±10 x605H ±10,Mechanism:- Synchro tilt Mechanism ,Gaslift:- Lift -Used gaslift of 90 mm,Armrest: PU Padded Adjustable armrest fixed,Chair Base & Wheels: Metal chrome plated Chair Baseconsists of 5 prongs with 650±5 mm pitch circle diameter, 50mm Dia. Black Nylon - Twin Wheel Pin castor.The product should bear IGBC Green Pro certificate for product category.And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design. 76 Supply & installation of Fixed Back visitor chair made of 12mm thick hot pressed plywood pasted with PU Moulded foam with Fabric upholstery on Seat , Used PU Moulded foam on Seat of D-45 kg/m3 , Back of High back chair is made of Injection moulded PP material structure upholstered with Mesh fabric , Adjustable Lumber support upholstered with fabric•Adjustable Lumber Support . Fixed PP Armrest . Synchro-Tilt Mechanism With Single Position Lock. CRCA Powder coated Cantileverframe .The product should bear IGBC Green Pro certificate for product category.And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design. 77 Supply & installation Two seater Sofa , Overall Size 1400W X 750D X 750H , Sofa structure made good quality solid wood of size 38x25mm Uphostered With Leatherite & HD Foam used in seat & Back density 32 KG/m3, Sofa base Supported on metal legs , Sofa Back Height from ground is 750mm , The rounded Armrests Provided with Sleek And Stylish Look, complete Understructure Made of Solid Wood Structures With Heavy duty zig zag Spring For Maximum Comfort, Seat Height From Ground 460mm , 100mm High Legs . The product should bear IGBC Green Pro certificate for product category.And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design. 78 Supply & installation of Three seater Sofa , Overall Size 1920W X 750D X 750H , Sofa structure made good quality solid wood of size 38x25mm Uphostered With Leatherite & HD Foam used in seat & Back density 32 KG/m3, Sofa base Supported on metal legs , Sofa Back Height from ground is 750mm , The rounded Armrests Provided with Sleek And Stylish Look, complete Understructure Made of Solid Wood Structures With Heavy duty zig zag Spring For Maximum Comfort, Seat Height From Ground 460mm , 100mm High Legs . The product should bear IGBC Green Pro certificate for product category.And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design. 79 Supply & installation of Centre Table Overall Size 1215W X 605D X 450H mm, Table Top Made Of Veneer & Melamine polish, Inner material used in Table top is 18mm thickness commercial block board & prime quality veneer pasted on it with Melamine polish, Table Top Size 1215W X 605D X 18mm Thickness, Teak colour Veneer pasted on table top, Legs made up of solid teak wood material of size 60W X 60Dmm, Under structure Top Supported Panel Made Of Prime Quality Solid teak Wood material of size 60x20mm, complete structure are in Melamine polish, commercial Board Use Prime Quality With ISI Marked , All Wooden Panels Cleaning Corner Knitted Finish , Wooden Panel Joint Leg To Leg Supported To Top . The product should bear IGBC Green Pro certificate for product category.And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design. 80 Supply & installation of Three Seater Waiting sofa Overall Size 1800W x 670D x 785H , Seat Height 425mm , Seat & Back made of 1.2mm thick perforated sheet metal duly powder coated , seat & back cushioning made of Wooden Structure 6mm Ply (Hot Pressed) with foam upholstered With Leatherette , Seat & back made of CRCA Sheet Perforated (Base & Back Are In Single L Shape With Radius At Bend) Powder Coated In Silky Silver & Covered By Cushion , Base Frame Beam 80H x 40W x 1795L 1.82mm Thick , Height of the seat from floor 425mm, Beam MS ERW Rectangular Tube Black Powder Coated , Leg Chrome Plated Rectangular MS Structure , Bow Shaped 1.2mm Thick Sheet , 1.2mm Thick Arm Rest Chrome Plated Rectangular MS Structure, Perforated Seat & Back fixed with MS Brackets duly powder coated , Beading Chrome Plated Ms Channel Beading , Level Adjuster Chrome Plated MS Cap With PVC Inserted Black Colour , All Pipes Shall Be Welded Properly Strongly and conformity with regulations. 81 Supply & installation of Two Seater Waiting sofa Overall Size 1190W ±10 x 670D ±10 x 785H ±10 , Seat Height 425mm, Seat & Back made of 1.2mm thick perforated sheet metal duly powder coated , seat & back cushioning made of Wooden Structure 6mm Ply (Hot Pressed) with foam upholstered With Leatherette , Seat & back made of CRCA Sheet Perforated (Base & Back Are In Single L Shape With Radius At Bend) Powder Coated In Silky Silver & Covered By Cushion , Height of the seat from floor 425mm, Beam MS ERW Rectangular Tube Black Powder Coated , Leg Chrome Plated Rectangular MS Structure , Bow Shaped 1.2mm Thick Sheet , 1.2mm Thick Arm Rest Chrome Plated Rectangular MS Structure , Perforated Seat & Back fixed with MS Brackets duly powder coated , Beading Chrome Plated Ms Channel Beading , Level Adjuster Chrome Plated MS Cap With PVC Inserted Black Colour , All Pipes Shall Be Welded Properly Strongly and conformity with regulations .The product should bear IGBC Green Pro certificate for product category.And should be BIFMA member having AIOTA (All India Occupational Therapists Association) for OFFICE FURNITURE range for ergonomic design.
