Tender For Provision Of 02 X Training Shed At Fatehgarh; 1 M & L for surface dressing n.exc. 15 cm deep and getting out in soft/loose soil complete all as specified and directed. 2 Excavation over areas, n exc 1.5 m deep for foundation and getting out in soft/loose soil complete all as specified and directed. 3 Excavation over areas,exc 1.50 m but not exc.3 m depth for footing in soft/loose soil etc cpmplete all as specified and directed. 4 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm of soft/ loose soil complete all as specified and directed. 5 Removing excavated material (soil) n. exc. 50 m and depositing where directed at alevel n. exc. 1.5m above the starting point etc complete all as specified and directed. 6 M & L for PCC 1:3:6type C-2 (using 40 mm graded stone aggregate) as infoundations, filling and mass-concrete etc complete all as specified and directed. 7 M & L for RCC M-25 design mix (using 20 mm graded stone aggregate ) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete etc complete all as specified and directed. 8 M & L for RCC M-25 design mix (using 20 mm graded stone aggregate)as in Columns, pillars, piers, posts and struts etc completeall as specified and directed. 9 M&Lfor RCC M-25 design mix (using 20 mm graded stone aggregate)as in Beams, cantilevers, bressummers, lintels over 1.5m span etc completeall as specified and directed. 10 M & Lfor RCC M-25 design mix (using 20 mm graded stone aggregate)as in Chajjas, Gutteretc completeall as specified and directed. 11 `M & LforRCC M-25 design mix (using 20 mm graded stone aggregate )as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc completeall as specified and directed. 12 M & Lfor RCC M-25 design mix (using 20 mm graded stone aggregate )as in stair ways including steps (square or spandril), string pieces, carriages, etc., complete, any section straightetc completeall as specified and directed. 13 M & L for flat, rough finished surface formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batteretc complete all as specified and directed. 14 M & L for for flat, rough finished surface form work as in sides of columns etc complete all as specified and directed. 15 M & L for for flat, rough finished surface form work as in roof beams ,lintel and intermediate beametc complete all as specified and directed. 16 M & L for flat, rough finished surface formwork to soffits of suspended slabs such as roof slabs, floorslabs, landings and similar work; not exceeding 200mm thick(Horizontal or sloping etc complete all as specified and directed. 17 M & L forflat, rough finished surface formwork to chullah hoods, chajjas, Gutter and similar items including edgesetc complete all as specified and directed. 18 M & L for rough finished surface formwork to staircases with sloping or stepped soffits including risers and stringers (excluding landing) etc complete all as specified and directed. 19 S & F for roof trusses (framed),crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc conforming to Fe 410-W (Gde E-250) quality B complete all as specified and directed. 20 S & F for Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates etc conforming to Fe 410-W (Gde E-250) quality B complete all as specified and directed. 21 S & F for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified and directed. 22 S & F for pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in ridge/valley gutter roof covering/ cladding to wall, fixed with self tapping screws as specified and directed. 23 S&F MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment (Fe 410-W (Gde E- 250) quality A ) complete all as specified and directed 24 S&F Mild steel screw bolts of 16-20 mm dia and length of bolt exc 5cm but n exc 10cm long (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square complete all specified and directed 25 M & L for preparation of new or previously untreated surfaces of steel over a coat of red oxide primer over and encluding two coat of synthetic enamel paint, surface of any description over 10cm in width or girth, not otherwise described complete all as specified and directed. 26 M & L for rendering 15 mm thick in CM 1:4 on bricksurfaces fair finished even and smooth without using extra cement complete all as specified and directed. 27 M & L for rendering 5 mm thick in CM 1:4 on concrete surfaces fair finished even and smooth withoutusing extra cement complete all as specified and directed. 28 M & L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over one coat of putty complete all as specified and as directed. 29 M & L for moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering etc all as specified and directed. 30 M & L for PCC 75mm thick1:3:6 type C-1using 20 mm stone aggretate as in plinth protection including joint fillingand coarse sand mixture. 1:3 (by weight) at the joints complete all as specified and directed. 31 M & L hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface(Broken stones / boulders) etc complete all as specified and directed. 32 M & L for 75 mm thickPCC, 1:4:8 type D-2,(40mm graded stone aggregate) as in base /sub base of floor complete all as specified and directed. 33 M & L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as specified and directed. 34 M & L for mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders etc complete all as specified and directed. 35 M & L for brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 etc all as specified and directed. 36 M&L for machine cut kota stone with mirror polishingforflooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete.Including Screed bed or bedding layer of mortar 20 mm thick in CM 1:6 for laying floor finishes complete all as specified and directed. 37 M&Lfor green marble 18 to 20mm thick(table rubbedand polished)in steps,jambs,pillars, window cills, cooking platforms and border of kota stoneincludingpointing in white cement (1:2) usingmarble dust with admixture of pigment to match with marbleshadeincluding 15mm screed bed in cement mortar (1:4)complete all as specified and directed. 38 M&Lformarble matching with platformcolour 18 to 20mm thick(table rubbedand polished)in riser and vetrical face of brick /RCC wall includingpointing in white cement (1:2) usingmarble dust with admixture of pigment to match with marbleshadeincluding Rendering 10 mm thick in cement mortar (1:4)on fair faces of brick work or concrete surfaces complete all as specified and directed. 39 M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, includingfixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel boltsetc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed 40 S&F 15 mm bore tubes medium grade galvanised, with all fitting and fixed complete to wall and ceilings or laid in floor complete all as specified and directed. 41 S&F 20 mm bore tubes medium grade galvanised, with all fitting and fixed complete to wall and ceilings or laid in floor complete all as specified and directed. 42 S&F rotational moulded polyethylene water storage tanks 1000 ltr capacity in triple layer (cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia PTMT Float valve complete all as specified and directed. 43 S&F gun metal glove or gate valve with iron wheel head, screwed both ends for 20 mm iron pipe and fixed screws complete all as specified and directed. 44 S&F15 mm dia bore stop angle cock chromium plated screwed down high pressure with crutch or butterfly handle,screwed both ends for iron pipe or for unions complete all as specified and directed. 45 S & F PVC ( SWR )pipe 75 mm dia single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed. 46 S&F 110 mmbore PVC(SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed. 47 S&F 110 mm bore PVC(SWR) bends any radius complete all as specified and directed. 48 S&F 75 mm bore PVC(SWR) bends any radius complete all as specified and directed . 49 M&L 75 mm dia. PVC floor trap with grating including joining to waste pipe fixed in solvent cement complete all as specified and directed. 50 S&Fvitreous chinawash hand basins, white , flat back of size 550 x 400 mm including 32mm bore waste coupling chromium plated including 32mm bore pvc waste pipe including fixing cantilever brackets connection unions to pipes etc fixed complete all as specified and directed . 51 S&F 15 mm bore bib taps fancy type cast copper alloy chromium plated long shank with crutch or butterfly handle screwed down for iron pipe or brass ferrule and fixed complete all as specified and directed. 52 S&FPVC connnection 15mm size with PTMT nuts of length 450mm long complete all as specified and directed. 53 S&F 15mm bore pillar tap fancy type cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed. 54 S&Fvitreous china urinal, half stall type (white) with grating and union for discharge pipe, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) etc complete all as specified and directed. 55 S&F vitreous china urinal partition white of size 310 mm X 700 mm complete all as specified and directed. 56 M&L PCC 1:3:6 type C-2 (using 40 mm graded stone aggretate) concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested for 10 mm bore pipe complete all as specified and directed. 57 M&L for salt glazed stone ware drain pipes grade A of size 100 mm laid in trenches and jointed in CM (1:1) complete all as specified and directed. 58 M&L for non- kid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed layer of mortar 15mm thick in CM 1:6 for laying floor finishes complete all as specified and directed. 59 M&L for Glazed ceramic coloured tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including rendering 10mm thick CM 1:3 on fair faces of brick work or concrete surfaces complete all as specified and directed. 60 S&F solid PVC door frame of size 50mmx 47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, as per SSR specification all as pecified and directed. 61 S&F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tube for top and bottom rails, MS frame shall be covered with sheet molded plain colour PVC sheet fixed with 20mm width sturck in side with solvent cement for style and plain colour PVC sheet for top rail, lock rail and bottom rail on either side as in gap insert for top rail, botttom rail paneling or plain colour PVC sheet beading and jointed together with solvlent cement, fixing in the frame at site as per SSR specificationcomplete all as specified and directed. 62 S&F 150 mm aluminium anodized, barrlel tower bolts of extruded section complete all as specifed and directed. 63 S&F 200 mm long aluminium anodized, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed. 64 S&F 100 mm long butt hinges, cast brass,with mild steel hinge pin, bright polished and fixed, type B-11 with steel screws as in pvc door complete all as specifed and directed. 65 S&F Steel windows or ventilators, fixed type, with glazing barscomplete all as specified and directed. 66 S&F for sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm complete all as specified and directed. 67 S & F framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors, ladders, framed balusters, walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165complete all as specified and directed. 68 S & F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples in steel window/ventilator complete all as specified and directed. 69 S&F 100mm aluminium handles, fabricatd type, anodised complete all asspecified and directed. 70 Surface excavation n.exc 35cm deep and averaging cm and averaging 15cm deep and getting outin soft/loose soil complete all as specified and directed 71 Rolling and consolidating formation surfaces in cutting with power roller exc 8 ton but n exc 12 ton complete all as specified and direcetd 72 M&L for soling (or sub base) 150mm thick (spread thickness) with granite, trap or basalt broken boulders or quarried stones, interstices filled, surface and rolled and consolidated to required gradient and camber 73 M&L for WBM 150mm thick (compacted thickness) in two layers of 75mm each with course aggregate of grading II (63 to 40mm) size, spread, leveled and rolled and consolidated to required gradient and camber using grainite, trap or, basalt stone complete all as specified and directed 74 M&L for preparing unsurfaced WBM surface by wire brushing with wire brushed for removing caked mud etc sweeping with brooms and finally fanning the cleaned surface with gunny bags to remove all loose dust etc complete all as specified and directed. 75 M&L for applying evenly a priming tack coat with bituminous primer @ 10Kg/10Sqm using paving bitumen complete all as specified and directed. 76 M&L for 75 mm thick (consolidated thickness) premix bituminious macadam with 4% binder contentusing paving bitumen of VG-30 grade by weight of total mix laid / rolled and compacted to required camber and gradient complete all as specifiied and directed.Note : (a) Premix bituminious macadam shall be obtained from hot mix plant and spreading shall be done with mechanical paver and asphaltic dense concrete work shall be done within 48 hours after completion of rolling and consolidation of bituminious macadam. (b) Contractor shall quote his rate on the basis of binder as mentioned in above item.If there is any variation in the actual binder content used,the rate shall be adjusted @ Rs. 45/- per Kg of the binder used.However no price adjustment shall be made if the binder content workout to more as specified in shedule A. 77 M&L bituminous premix asphaltic dense concrete 40mm consolidated thickness with 5.5% binder using paving bitumen content by weight of total mix, rolled and compacted to required camber and gradient complete content by weight of total mix rolled and compacted using 8 to 10 tonne capacity power road roller to achieve the required compaction camber and gradient complete all as specified and directed. 78 M&L continuous brick edging; with width equal to the depth of the brick, of whole sub-class B Bricks old sizelaid on end vertically complete all as specified and directed. 79 Removing excavated material (hard/dense soil) to a distance exceeding 50m and not exceeding 100m& depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed. 80 Supply and fixing cat eye solar reflective type of metal body alloy of size 100mm x 100mm x 20mm with PAMA striplens reflector of model No. DA 972.0 fixed with and incl MS stud of suitable size as per manufactures instructions complete all as specified and directed. 81 M & L for preparing bituminous surfaces of road and marking 2.5mm thick centre lines, stop lines, dashes, arrows etc. and the like n. exc 10cm wide on roads pavements with hot applied thermo plastic road marking paint of approved colour confirming to BS 3262-1989 with special applicator machine all as per manufacturers instruction complete all as specified and directed. 82 Surface excavation n. exc 30 cm deep and averaging 15 cm thick in soft/loose soil etc complete all as specified and directed. 83 M&L for 75mm thick PCC 1:4:8 type D-2(using 40 mm graded stone aggregate) as in lean concrete etc complete all as specified and directed. 84 Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of requiredshape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete.etc complete all as specified and directed. 85 M&Lfor PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in kerb, benching etc complete all as specified and directed. 86 Excavation in trenches not exceeding 1.5 mtrs wide and not exceeding 1.5 mtrs in depth for foundation, etc or for shafts, wells, cesspits, manholes, laying of cables including getting out in soft/loose soil complete all as specified and directed. 87 Cutting existing CI/GI pipe line 40 mm dia for insertion of tee of size 40 x 40 x 40 mm for branch connection including excavation and earth work complete all as specified and directed. 88 Cutting existing CI/GI pipe line 40 mm dia for insertion of tee of size 40 x 40 x 25 mm for branch connection including excavation and earth work complete all as specified and directed. 89 Supply and fixing for 40 mm bore galvanised steel tubing, medium grade with all fittings and fixed to wall, ceilings or laid in floor, trenches complete all as specified and directed. 90 Supply and fixing for 25 mm bore galvanised steel tubing, medium grade with all fittings and fixed to wall, ceilings or laid in floor, trenches complete all as specified and directed. 91 Supply and fix gun-metal, globe or gate valvs, 25 mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. 92 S&F Mild TMT steel bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bendingand binding with the mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed 93 M&L pre-cast RCC 1:2:4 Type B-1 (20mm graded stone aggregate) as in cover slab for drain and similar work complete all as specified and directed 94 M & L PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate)as in bed of surface channel of drain including providing necessary formwork complete all as specified and directed. 95 M&L extra for forming fair finished drain or channel 30 cm inner girth in cement concrete,using extra cement including forms,moulds, mitred/stopped ends etc. complete all as specified and directed 96 Removing excavated material exc. 100 m but n exc. 200 m and depositing where directed complete all as specified and directed. 97 M&L for soakage wells of size (3.0 M dia x 4.5 M effective depth) including excavation, in any type of soil, foundation in PCC 1:3:6 type C-1 (using 20 mm graded stone aggretate), walls of honey combed masonary in CM 1:4 with cover slab of M-25 precast concrete/SFRC cover, top ring RCC 1:2:4 type B-1 (using 20 mm graded stone aggretate), including intercepting chamber and screen chamber made ofbrick masonary in CM,interconnecting pipes of RCC/DWC complete filled with brick bats complete all as specified and directed. 98 Excavating post holes in soft/Loose soils (or similar holes ) nexc 0.50 Cum each and getting outand returning filling in balance portion (after PCC filling Ref note given below) with boulder and mixed with earthin layers exceeding 25 Cm thick complete all as specified and directed. 99 S&F posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc flat iron fillets (for securing wire mesh etc) including all necessary drilling bolting or riveting etc; half round or other stock section, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. 100 Supply and fixing mild steel in flat,round or square bars in available legth complete all as specified and directed. 101 M & L for PCC 1:4:8 type D-2 (40mm gradedstone aggregates) in foundation filling and mass concrete complete all as specified and directed 102 M&L for RCC 1:2:4 type B-1, (20mm graded stone aggregate), nominal mix in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. 103 M & L for preparation of new or previous untreated steel and ironsurfaces of anyn. exc 10 cm in width or girth and applyingtwo coat of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed . 104 S&F for GIbarbed wire 2 strand steel barbed wire 2.24 mm dia barbed with 2 mm barbs at 75 mm spacingand shallconfirming to IS-278-2001 &IS-280-2006 and straining and fixing to any type of standrad rails straining bolts including securing or tying at crosssing with and provision of Galvanized mild steel wire, staples or steel pins etc as directed complete all as specified and directed. 105 Supply only chain link MS galvanised fencing weight not more than 4 Sqm any size or type complete all as specified and directed. 106 Fixing only chain link fencing including line wires ,any mesh and any type of standrads rails, straining bolts etc including provisioning of binding wire complete as directed. 107 Mild steel screw bolts (Machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exceeding 5 Cm long but not exceeding11 to 15mm dia of neck complete all as specified and directed. 108 M&L for 5.5m steel gate complete all as shown on drg No. TD/104/11 complete all as specified and directed. 109 M&L for point wiring complete forOne light/Fan/Exhaust fan/Bell pointcontrolled by one switch with PVC insulated and unsheathed FRLSH cable 1.5 sqmm (nominal area), ISI marked,multi stranded copperconductor cable, 1100 volt grade including ISI marked not less than 20mm dia medium grade PVC conduit concealed in wall , MS conduit in roof/floors, factory made pressed steelconcealed terminal boxes not less than 1.6mm thick of reqd size and with top cover 3mm thick of plastic laminated sheets of required colour complete,including 1.5 Sqmm PVC ,FRLSH cableinsulated unsheathed multi stranded copper earth wire to the common earth and connecting to earth dolly,including colour coding of cable shall be Phase-red,Neutral-black and Earth- green with all accessories and complete all as specified and directed.Note :-(i) In case of roof/ceiling, heavy duty PVC pipe shall be used without any extra cost. (ii)The quoted rete is deemed to be included for the chases cutting. (iii) Cutting chases for concealed shall be made good using CM 1:4 and surface finished to match the existing surface & colour. 110 M&L for point wiring complete for One 5 pin 5 Amp switch socket out let point on an independent board with PVC insulated and unsheathed FRLSH cable1.5 sqmm (nominal area), ISI marked,multi stranded copperconductor cable including ISI marked not less than 20mm dia medium grade PVC conduit concealed in wall , MS conduit in roof/floors, factory made pressed steelconcealed terminal boxes not less than 1.6mm thick of reqd size and with top cover 3mm thick of plastic laminated sheets of required colour complete,including 1.5 Sqmm PVC ,FRLSH cableinsulated unsheathed multi stranded copper earth wire to the common earth and connecting to earth dolly,including colour coding of cable shall be Phase-red,Neutral-black and Earth- green with all accessories complete for max four nos socket outlets all as specified and directed. Note :-(i) In case of roof/ceiling, heavy duty PVC pipe shall be used without any extra cost. (ii)The quoted rete is deemed to be included for the chases cutting. (iii) Cutting chases for concealed shall be made good using CM 1:4 and surface finished to match the existing surface & colour. 111 M&L for point wiring complete for One 5 pin 5 Amp switch socket out let point on an same board with PVC insulated and unsheathed FRLSH cable1.5 sqmm (nominal area), ISI marked,multi stranded copperconductor cable 1100 volt grade, including ISI marked not less than 20mm dia medium grade PVC conduit concealed in wall , MS conduit in roof/floors, factory made pressed steelconcealed terminal boxes not less than 1.6mm thick of reqd size and with top cover 3mm thick of plastic laminated sheets of required colour complete,including 1.5 Sqmm PVC ,FRLSH cableinsulated unsheathed multi stranded copper earth wire to the common earth and connecting to earth dolly,including colour coding of cable shall be Phase-red,Neutral-black and Earth- green with all accessories complete for max four nos socket outlets all as specified and directed. Note :-(i) In case of roof/ceiling, heavy duty PVC pipe shall be used without any extra cost. (ii)The quoted rete is deemed to be included for the chases cutting. (iii) Cutting chases for concealed shall be made good using CM 1:4 and surface finished to match the existing surface & colour. 112 M&L for point wiring complete forOne light/Fan/Exhaust fan/Bell point on an independent board controlled by one switch with PVC insulated and unsheathed FRLSH cable2.5 sqmm (nominal area), ISI marked,multi stranded copperconductor cable 1100 volt grade, including ISI marked not less than 20mm dia medium grade PVC conduit concealed in wall , MS conduit in roof/floors, factory made pressed steelconcealed terminal boxes not less than 1.6mm thick of reqd size and with top cover 3mm thick of plastic laminated sheets of required colour complete,including 2.5 Sqmm PVC ,FRLSH cableinsulated unsheathed multi stranded copper earth wire to the common earth and connecting to earth dolly,including colour coding of cable shall be Phase-red,Neutral-black and Earth- green with all accessories and complete all as specified and directed.Note :-(i) In case of roof/ceiling, heavy duty PVC pipe shall be used without any extra cost. (ii)The quoted rete is deemed to be included for the chases cutting. (iii) Cutting chases for concealed shall be made good using CM 1:4 and surface finished to match the existing surface & colour. 113 S&F switch flush type 5/6 Amps single pole one way complete all as specified and directed. 114 S&F Socket outlet, flush type 2 in 1, 3 pin, 5/6 Amps complete all as specified and directed. 115 S&F Switch socket combination 2 in 1flush type 5/6 Amp 5 Pin complete all as specified and directed. 116 S&F Switch socket combination 5 in 1, 15 Ampflush type complete all as specified and directed. 117 Supply and fix electronic fan regulator 5 stepped type complete all as specified and directed 118 S&F ceiling rose PVC/Poly carbonate isolated body three terminal AC 230 volts complete all as specified and directed. 119 M&L submain wiring with two single core 6 sqmm FRLSH copper conductor, PVC insulated, multistranded, unsheathed cable ISI marked drawn in PVC conduit concealed in wallsurface / ceiling for sub main connection including one 6 sqmm FRLSH one single core PVC insulated multistranded unsheathed copper conductor used as earth wire to common earth and connection to earth dolly complete all as specified and directed. Note:- Two single core 6 sqmm copper conductor for phase / neutral, one run PVC conduit and one run of 6 sqmm earth wire shall be considered & measured as one unit. 120 Supply and fixing of VTPN DB 12 way suitable for Mounting MCCB as Incomer of rating 100 Amp with suitablerated bus bar having IP-43 protection and double metal door includingMCCB 100 Amps, AC, 415 Volt, 4 Pole, 16 KA with thermal magnetic trip unit (TMTU) adjustable thermal setting 0.7 - 1 x In, class II front face, Ics = 100% Icu as per IS/IEC 60947-2 including connection with aluminium thimbles as required complete all as specified. 121 Supply and fixing of MCB distribution board SPN 240 Volt 8 way with 200 Amp rated bus bar having IP-43 protection and double metal door concealed in wall including connection with aluminium thimbles as required complete all as specified. 122 S&F of MCB SPN 40-63 Amp 240 volt Ccurve 10 KA complete all as specifed and directed. 123 S&F of MCB SP 10 to 32 Amp 240 Volt C curve 10 KA complete all as specified and directed. 124 Supply and fixing LED lights fitting 4 Ft, 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. 125 S & F building security LED Light 30 Watt made up pressure die-cast aluminium housing with high power LED as lighting source and lens embedded PC having top opening separate driver compartment with IP-65 protection and impact resistance of IK 07 for building secuity purpose with bracket size made of GI pipe medicum grade 40 mm dia 1.5 mtr long bend to shape as required and fixing with two nos MS Clamp of size 40x6 mm for fixing of builiding security light fittings completed all as specified and directed. 126 Supply and fixing ceiling fans complete with blades, down rods (as per site requirement), electronic regulator and accessories, 230 V, 1400 mm sweep min air delivery 245 CFM with service value 6.00 BEE five star rated with brushless direct current motor (BLDC) complete all as specified and driected. (Note:- Additional length of down rods are also included.) 127 Supply and fixing of exhaust fan, steel body AC single Phase 230V of size 380m sweep with, blades, and frame and louvers including complete fitting into the wall and all as specified and directed. 128 Supply and Laying cable XLPE Insulated screened PVC bedded, galvanized steel strip armoured service cable pole to building electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 Sqmm 3.5 Core complete all as specified and directed. 129 S & F40 mm bore GI Tubing light grade with all fittings laid across road, in trenches or across PCC drain, along electric pole or floor/wall for cable protection with suitable size of MS Clapms and nut and bolts/washer complete all as specified and directed. 130 Supply & laying sand cushioning to under ground cable in layers of 23 cm thick (8 cm before laying the cable and 15 cm thick after laying the cable, punned thickness shall be measured) in trenches complete all as specified and directed.Note: - Only punned thickness shall be measured and paid. 131 M&L for protection to cable with well burnt sub class B bricks laid dry flatbrick,width equal to length of brick complete all as specified and directed. 132 S&F of metal plug & socket DB with metal plug and MCBs single pole enclosere with a two pin earth plug and socket suitable for 20 Amp complete with one single pole MCB complete all as specified and directed. 133 M & L Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground.(earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr. belowground level connecting to galvanised earth lead wire 4.0 mm diaas earth lead upto 7.5 meters long connected by means of bolts, check nuts and washers of GI and earth wire protected by provision of GI pipe medium grade, 15 mm bore including provn of concrete pit in PCC (1:2:4) type B-1 using 20mm graded crushed stone aggregates with 40mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4Kg/Sqm) and frame of angle iron 40 x 40 x 3mm fixingwith 6mm dia MS bar handle made to shape, GI light grade 20mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge plate, common salt and charcoal filling, with fixing arrangement, funnel, wire mesh and earth work in hard / dense soil, returning filling in and removal of surplus soil to a distance not exeeding 50 mtr, all as per electrical plate No 3 of SSR 2009 Part-I and connection all as specified and testing on completion. Note: The cost of excavation and earth work, PCC pit and pit covers, funnel and watering pipe, wire mesh, charcoal dust and common salt,20/ 40mm dia, medium grade, GI pipe as protection to GI wire 4.0 mm as main earthing lead from earth electrode to main TPN MCCBs DB/MCB DB/ test point length not less than 7.5mtrs) shall be deemed included in the unit rate for earthing and testing complete all as specified and directed .
