Tender For Various Development Works In Park At Rajeev Nagar Ganeshpura, Bhadana, Ward No. 24 - 1 Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils 2 Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M10 grade Nominal Mix 1: 3: 6 (1 cement : 3 coarse sand : 6 graded stoneaggregate 20mm nominal size). 3 Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in: Cement Mortar 1:6 ( 1-Cement : 6-Sand). 4 M-30, 60 mm thick to be used in non traffic areas like building premises, monument premises, land scapes, public gardens/ park, domestic drives, paths and patios, Embankment slopes, sand stabilization Area etc.( As per table 1 ofIS 15658:2006Category‘B’ Denated only two side like I,Z,T shape etc. as per IRC SP 63:2004 5 ADD EXTRA FOR COLOUR INTERLOKING 6 Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M20 grade Nominal Mix1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stoneaggregate 20mm nominal size). 7 Providing and laying damp-proof course with cement concrete grade M-150 (1 : 2 : 4) mortar prepared with 1% solution of water-proof compound completeandno glass strips are used andnot applying 2 coats of hot bitumen complete as per specifications. 50mm thick. 8 Random rubble dry stone Kharanja under floor. 9 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement in position to the required line, level and curvature jointed with cement mortar 1:3 (1 cement : 3 coarse sand ) including making joints with without grooves (thickness of joints except at sharp curve shall not to more than 5mm) including making drainage opening wherever required complete including painting etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineerin- charge). 10 Painting exterior surface ofWallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty,etc complete in all respect. 11 Painting exterior surface ofWallwith 100% acrylic exterior paint of approved brand and manufacture to give an even shade with two or more coats including prepartion of base with sand papering, primer, putty,etc complete in all respect. New work (Two or more coats applied @ 3.84 kg/10 sqm). 12 Painting with synthetic enamel paint of approved brand and manufacture togive an even shade :Two or more coats on new work 13 Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide 14 Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 20mm thick. 15 P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant. 110 mm dia 16 P & F PVC Storage Tank ISI Marked (IS : 12701) indicating theBIS license No),of approved make with cover, 25mm dia 1M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc., complete of approved design: 500 litres capacity. 17 P & F Ball Cock (IS :1703 Mark) with Rod& P.V.C. Ball complete :Brass wt.Not less than 400 gm, 20mm. 18 Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/ vertical or curved surfaces)excluding the cost of purlins, rafters and trusses and including cutting to size and shape whenever required.0.63 mm thick with zinc coating not less than 275 gm/m2 19 Providing and fixing welded mesh/expanded metal mesh in frame work, flat iron beading 20x3mm including top cross laps inside and out sides welding, iron bolts, crews, clips etc. complete (excluding frame work) of size.Welded mesh 50 mmx 50 mm x 2.1 mm 20 Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)inrecessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & itsISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thickHot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws,making connections, testing etc. as required.For specification of copperConductor,Phenolic Laminated sheets & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure A attached with this BSRShort point (up to 3 mtr.) 21 Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5,in existingsurface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure A attached with this BSR2 x 2.5 sq. mm. + 1x1.5sqmm 22 Supply , Installation, Testing and Comissioning of IS:1475 marked self contained drinking water cooler withhermeticallysealed compressor,non CFC refrigerent suitable for operation on 230V/1pH/50Hz AC supply,Full stainless steel (SS304)body (0.8 mm thick)and tank (0.5 mm thick) , stainless steel water tray,minimum two nosBrass Chrome plated faucets and suitable drainage system complete in all respect with requiredheight MS fabricated and Painted Angle iron frame( Cost of frame to be paid Extra )complete in all respect of the following capacity.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . cooling capacity 150 Ltr./Hr. and storage capacity 150 Ltrs 23 Providing and fixing of power plug point with non modular accessories as per PWD specification for electrical Works withGalvanized box of 1.2 mm thickwith earth terminal with suitable size phenolic laminated sheet (IS : 2036 -1995) cover including cost of 16 amp. Switch (IS :3854) and 3/6 pin 16 amp. socket outletmaking connection , testing , etc. as required. . For specification ofWiring accessories refer ChapterE - 07 related item &For additional technical parameters of product / work refer Annexure A attached with this BSR 24 Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load andsite requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per IEC,minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted inexisting distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above ratingincluding making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure A attached with this BSR50/63 Arating 25 Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5,in existingsurface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure A attached with this BSR2 x 4.0 sq. mm. + 1 x 2.5 sq. mm. 26 Wave Slide : The sliding chute of wave slide is made of 6mm thick fibre glass reinforced plastic. (Binani or equivalent make) with a smooth surface consist of 3 sliding mould of 2.00 ft. (approx). The platform made out of 10 gauge MS sheet and shall be supported on 33mm OD 14 gauge. The ladder shall be 60cm wide (approx) and will be made of 25mm NP pipe with 15mm dual steps. The slide shall be supported on three parallel supports of different length. the size of the slide above the ground level shall be as follows platform height 2.40, slide length 4.20m and slide width 0.50 mtr. (approx) 27 Single See Saw : The Single See Saw suitable for 4 to 8 years children and made of MS pipes which should be following specification : Area Required : 1.50 mtr.x 3.0 mtr.Height : 0.90 mtr. Main Pipe : 50 NB pipePlank : 40 NB pipeHandle : 20 NB pipeSeats : MS sheet (5mm thick) FRP (ISO : 9001-2000 make) 28 Parallel bars : Parallel Bars is suitable for 10 to 16 years children and main verticle frame made of 50mm NB pipe and horizontal bars made of 32mm NB pipes. Horizontal bars having length 2.10 mtr. and height is 1.20 mtr. On ground level. Total area of this parallel is 2.0 mtr. x 1.0 mtr. 29 Double Swing : Double Swing is suitable for 4 to 14 years Children and frame is made of NB pipes which should be following specifications :Area : 3.0 mtr x 2.50mtr.Safe play area : 4.0 mtr x 3.50 mtr.Height : 2.40 mtr. (on ground level)Leg support : 40mm NB pipes Top bar : 50mm NB pipe Seat : 9mm thick reinforced rubber (Non skid chequired top, bearing : Housing special casting heavy duty bail bearing, suspension : 7mm dia Electro Galvanized chain (ISO : 9001-2000 make) 30 Up and Down Ladder : Providing and Fixing of up-down ladder made out of MS pipe 40mm, 25mm size of length 10xheight should be less than 6 pipe should be ISI marked of heavy weight. 31 S/F of following outdoor Gym (fitness) Equipment including excavation of foundation in all kind of soil/hard roack. construction of foundation as per requirement of Gym Equipment or atleast 0.40x0.40x0.60m size in RCC M-20 mix or as per direction of engineer in charge. Gym equipment should be as per enclosed drawing and design in special conditions folowing make Kilkari/Regal/Arihant/Arogyam.Double Bar:Features : -H-46, L-66, W-3-4 Inch Dia. Galvanized Steel Pipe-Handle 1/1.25 inch Dia. M.S. PipePowder Coated 100-110 microns 32 Sit Up Board:Features : -H-39, L-46, W-21-4 Inch Dia. Galvanized Steel Pipe-Handle 1/1.25 inch Dia. M.S. PipePowder Coated 100-110 microns 33 Double Surf Board:Features : -H-44, L-310, W-32-4 Inch Dia. Galvanized Steel Pipe-Handle 1/1.25 inch Dia. M.S. Pipe-Powder Coated 100-110 microns- FRP Foot Rest 34 Sky Walker:Features : -H-48, L-51, W-18-4 Inch Dia. Galvanized Steel Pipe-Handle 1/1.25 inch Dia. M.S. Pipe- Powder Coated 100-110 microns- FRP Seat & Foot Rest 35 Cross Trainer:Features : -H-53, L-45, W-111-3 Inch Dia. Galvanized Steel Pipe-Handle 1/1.25 inch Dia. M.S. Pipe- Powder Coated 100-110 microns- FRP Seat & Foot Rest 36 Shoulder Builder Triple:Features : -H-63, L-48, W-36-3 Inch Dia. Galvanized Steel Pipe-Handle 1/1.25 inch Dia. M.S. Pipe- Powder Coated 100-110 microns 37 Double Twister Seating :Features : -H-44, L-71, W-22-4 Inch Dia. Galvanized Steel Pipe-Handle 1/1.25 inch Dia. M.S. Pipe- Powder Coated 100-110 microns 38 Ches Press Double:Features : -H-68, L-55, W-23-4 Inch Dia. Galvanized Steel Pipe-Handle 1/1.25 inch Dia. M.S. Pipe- Powder Coated 100-110 microns- FRP Seat & Foot Rest 39 Rower Double:Features : -H-38, L-76, W-27- 2x2 Inch Square CRCA Pipe-Handle 1/1.25 inch Dia. M.S. Pipe- Powder Coated 100-110 microns- FRP Seat & Foot Rest 40 Peck Deck Double:Features : -H-62, L-61, W-3,2-3 Inch Dia, Galvanized Steel Pipe-Handle 1/1.25 inch Dia. M.S. Pipe- Powder Coated 100-110 microns- FRP Seat & Foot Rest 41 Leg Press Double:Features : -H-58, L-64, W-17-4 Inch Dia. Galvanized Steel Pipe-Handle 1/1.25 inch Dia. M.S. Pipe- Powder Coated 100-110 microns- FRP Seat & Foot Rest
