Tender For 11 Kv Electrical Utility Shifting Work Under Eudd, Banda; 1 The work of erection of 11 KV HT/LT Overhead Lines & 25/100/250/400 KVA Sub-Stations shifting of above lines/double poles due to road widthening from Kyotara Chauraha to Kanwara Bypass (Bramha Dera) (Jail Road) fed from 33/11 KV Sub-Station, CHILLA ROAD, BANDA of EDSD, CHILLA ROAD, BANDA under FULL DEPOSIT SCHEME 2024-25 under EUDD, BANDA, including carriage of all required material from ESC Banda to work site, alongwith its loading, unloading & dragging at the respective ends and also safe carriage of old line material/scraped from site to store centre, if any. The bidder shall be responsible for complete execution of the work under the scope of tender specification. Any work/activity not specifically indicated but is required for systematic execution of job shall be carried out by the contractor without any extra payment. The material supplied by contractor should be the best quality and as per standard including transportation, if any. Details of the work as given below ;- 2 Safe cartage of 11 Mtr. long ST poles from store centre or from any other place to the respective site of work. 3 Safe cartage of 13 Mtr. long ST poles from store centre or from any other place to the respective site of work. 4 Safe cartage of line material viz. conductor, cable, G.I. earth wire, cross arm, angle, channel, insulator, clamps and other line material from store centre or from any other place to the respective site of work. 5 Erection of SP structure on 11 Mtr. long ST poles, including complete H.T./L.T. fittings as per RESSPO manual and as per direction of Engineer incharge. 6 Grouting of SP structure on 11 Mtr. long ST poles, including complete H.T./L.T. fittings as per RESSPO manual and as per direction of Engineer incharge. The support shall be grouted with cement, sand and brick ballast/stone ballast in ratio 1:4:8 (0.285 Cu. Mtr. each). 7 Erection of DP structure on 11 Mtr. long ST poles, including complete H.T./L.T. fittings as per RESSPO manual and as per direction of Engineer incharge. 8 Grouting of DP structure on 11 Mtr. long ST poles, including complete H.T./L.T. fittings as per RESSPO manual and as per direction of Engineer incharge. The support shall be grouted with cement, sand and brick ballast/stone ballast in ratio 1:4:8 (0.285 Cu. Mtr. each). 9 Erection of SP structure on 13 Mtr. long ST poles, including complete H.T./L.T. fittings as per RESSPO manual and as per direction of Engineer incharge. 10 Grouting of SP structure on 13 Mtr. long ST poles, including complete H.T./L.T. fittings as per RESSPO manual and as per direction of Engineer incharge. The support shall be grouted with cement, sand and brick ballast/stone ballast in ratio 1:4:8 (0.285 Cu. Mtr. each). 11 Erection of Tri-Pole structure on 13 Mtr. long ST poles, including complete H.T./L.T. fittings as per RESSPO manual and as per direction of Engineer incharge. 12 Grouting of Tri-Pole structure on 13 Mtr. long ST poles, including complete H.T./L.T. fittings as per RESSPO manual and as per direction of Engineer incharge. The support shall be grouted with cement, sand and brick ballast/stone ballast in ratio 1:4:8 (0.285 Cu. Mtr. each). 13 Erection and grouting of stay set with nozelling & binding as per norms. 14 Fixing of earthing rod as per RESSPO manual. 15 Laying, sagging, stringing, binding and jumpering etc. of ACSR Dog Conductor on the newly erected pole as per direction of supervising engineer/RESSPO manual. 16 Laying, stringing, binding and termination etc. of LT PVC Cable 1x400 Sq.mm. for connection to T/F LT bushing to LT Cable as per direction of supervising engineer/RESSPO manual. 17 Laying, stringing, binding and termination etc. of LT Armoured Cable 1x400 Sq.mm. for connection to T/F LT bushing to LT Cable as per direction of supervising engineer/RESSPO manual. 18 Laying & Hanging of 11 KV 3x185 Sq.mm. XLPE cable with support of Wire & cable hanging U clamp of appropriate strenght in such a manner that cable does not get stressed i.e. to be clamped and hanged at many support. Cable hoisting and making loops at both ends are also included in the work. (All material related to such work except cable to be arranged by contractor at his own cost). 19 Fixing of 11 KV Fuse set with fitting of all accessories as per RESSPO manual. 20 T/F Body Earthing complete by Gel/Chemical earthing (arranged by tenderer at his own cost). 21 Dismentling of old line due to shifting with all accessories and loading/unloading material from site to store. 22 Supply and erection/commissioning of 3x185 Sq.mm. 11 KV Cable Jointing Kit (Cable Box) (as per site requirement) for 3x185 Sq.mm. XLPE cable and making all suitable arrangements to get the work done (arranged by tenderer at his own cost). 23 Supply & erection/fixing of F/E-Bracket with Nuts-bolts & washers 11 KV alongwith fitting of all accessories as per RESSPO manual (arranged by tenderer at his own cost). 24 Supply & erection/fixing of Cross Arm Holding Clamp with Nuts-bolts & washers for ST Pole alongwith fitting of all accessories as per RESSPO manual (arranged by tenderer at his own cost). 25 Supply & erection/fixing of F/E-Bracket with Nuts-bolts & washers 33 KV alongwith fitting of all accessories as per RESSPO manual (arranged by tenderer at his own cost). 26 Supply & erection/fixing of Danger Board with clamp & nut-bolts 11 KV alongwith fitting of all accessories as per RESSPO manual (arranged by tenderer at his own cost). 27 Supply & erection/fixing of Copper L Piece 62x225x12 mm. alongwith fitting of all accessories as per RESSPO manual (arranged by tenderer at his own cost). 28 Supply & erection/fixing of Allu. Long Barrel Lugs 400 Sq.mm. alongwith fitting of all accessories as per RESSPO manual (arranged by tenderer at his own cost). 29 Supply & erection/fixing of MS Top Channel 125x65x3240 mm. 33 KV alongwith fitting of all accessories as per RESSPO manual (arranged by tenderer at his own cost). 30 Supply & erection/fixing of MS Top Channel 125x65x2400 mm. 11 KV alongwith fitting of all accessories as per RESSPO manual (arranged by tenderer at his own cost). 31 Supply & erection/fixing of MS Top Channel 125x65x2240 mm. 11 KV alongwith fitting of all accessories as per RESSPO manual (arranged by tenderer at his own cost). 32 Supply & erection/fixing of T/F Base Angle with suitable size nut-bolts alongwith fitting of all accessories as per RESSPO manual (arranged by tenderer at his own cost). 33 Supply & erection/fixing of MS Dropper Channel 100x50x2028 mm. alongwith fitting of all accessories as per RESSPO manual (arranged by tenderer at his own cost). 34 Supply & erection/fixing of MS T-Off Channel alongwith fitting of all accessories as per RESSPO manual (arranged by tenderer at his own cost). 35 Supply & erection/fixing of Clamps for channel with Nuts-bolts & washers alongwith fitting of all accessories as per RESSPO manual (arranged by tenderer at his own cost). 36 Supply & erection/fixing of MS Angle Iron 65x65x6x2700 mm. long Bracing with clamps & Nuts-bolts & washers alongwith fitting of all accessories as per RESSPO manual (arranged by tenderer at his own cost). 37 Supply & erection/fixing of Sub-station Structure Angle 65x65x6x3400 mm. long with Nuts-bolts & washers alongwith fitting of all accessories as per RESSPO manual (arranged by tenderer at his own cost). 38 Supply & erection/fixing of MS Cross Bracing Angle 65x65x6 mm, 4300 mm. with clamps & Nuts-bolts & washers alongwith fitting of all accessories as per RESSPO manual (arranged by tenderer at his own cost). 39 Supply & erection/fixing of PG Clamp for dog alongwith fitting of all accessories as per RESSPO manual (arranged by tenderer at his own cost). 40 Construction of new 11/0.4 kV, 250/400 KVA Transformer plinth of size 4x4x5 ft. above ground level and one ft. below the ground level of 9”. After excavation of 4” earth, brick ballast shall be provided and rammering will be done properly. After that a retaining wall of 9” width by first class brick in ratio 1:5 of cement and sand shall be made. The earth shall be filled up to one ft. below the top of the plinth. After this brick ballast shall be provided up to 6” from the earth level and proper rammering shall be done. One No. Jail of 12 mm MS tore shall be fixed in the hollow of plinth and one ft. thick RCC in ratio of cement, sand and stone ballast shall be laid on the top of the plinth. The 12 mm thick plastering shall be done all around the plinth in 1:4 ratio of cement and sand. The contractor shall be responsible to complete the work as per direction of Supervising Engineer. 41 Construction of toe wall with wire mesh or Pale fencing & painting of Sub-Stations, detail of the work as given below :-1- Construction of toe wall 9 wide 1 high above ground, all around the plinth/DP structure in 1:6 ratio of cement and coarse sand. The toe wall shall have pocket of 1200 mm size at the center of toe wall at appropriate places for grouting of MS Angle iron frames toe wall may very as per site conditions.2- Grouting & fixing of MS Angle iron frame in 1:2:4 ratio of cement, stone grit & coarse sand and bolting the frames with at joining frames by 35x8 mm bolt with nut. The size of MS Angle Iron frame may very as per requirement of site.3- Fabrication & Providing Gate in front of plinth/DP made in two leaves of size 900x1500 mm each. Each leave shall be made by MS Angle iron of 37x37x5 mm MS Angle and fitted with wire mesh or pale fencing of 18 SWG with the help of MS Strip of 35x5 mm size welded all around the frame. The leaves shall be fitted with hinges on MS Angle of size of 50x50x6 mm and shall have locking arrangement. Two gates shall be provided on such sub-station where more than one T/F are installed and that shall be counted two sub-stations.4- Fixing & Grouting of main gate at S.No. 1.03 made of MS Angle iron frame of 37x37x5 mm and 50x50x6 mm in the ratio 1:2:4 of cement, stone grit & coarse sand in front of DP/Plinth and to provide arrangement for locking the fencing with provision of lock & key.5- Plastering 10 mm thickness with cement, Mortar in ratio 1:4 cement and fine sand, including cost of all required material, labour & T&P etc.6- Painting of entire metal works including wire mesh or pale fencing with super enameled primer coat of Red Oxidein two coats of British/Asian Paint thereafter painting of same work with dark blue super enameled paint in again two coats of British/Asian Paint.7- Painting of Main Gate including wire mesh or pale fencing with super enameled primer coat of Red Oxide in two coats of British/Asian Paint thereafter painting of same work with dark blue super enameled paint in again two coats of British/Asian Paint.8- Safe carriage of MS Angle iron frame from nearest S/S to site of work, labour cost including loading and unloading at both ends.9- Safe carriage of MS Angle iron main gate from nearest S/S to site of work, labour cost including loading and unloading at both ends.10- Supply of MS Clamp for MS Angle Iron frame with nut & Bolts, washer four clamp.11- Supply of MS Angle Iron frame size of 37x37x5 mm for fixing of MS welded wire mesh 18 SWG or pale fencing made from MS Sheet size 1500 mm x 75 mm x 18 SWG with MS Strip of size 35x5 mm size of full frame. 42 Chopping of Tree Branches Coming in the vicinity of the lines during execution of the above works. 43 Safely shifting of medium power as 25/100/250/400 KVA transformers from the old ereted/existing single/double pole/plinth to new work/road side in proper alignment complete work, including the work of its cartage, loading & unloading at the respective ends due to widthening & saturation of above road. 44 Safely installation of additional medium power 250 KVA transformer due to increasing capacity of 11/0.4 KV S/S in old erection double pole/plinth to work/road side in proper alignment complete work, including the work of its cartage, loading & unloading at the respective ends due to widthening & saturation of above road.
