Repair And Maintenance Of Civil Works At Urja Nagar, Vidyut Vihar, 132 Kv Gss Rest House, Office Building At Barmer And Glpl Site. - 1 1.1/B-1 Earth work in surface excavation not exceeding 30 Cm. In depth but exceeding 1.5 meter in width as well as 10 Sqm. on plan including disposal of excavated earth up to 50 Mtr. And lift up to 1.5 Mtr. Disposed soil to be leveled and neatly dressed : All kinds of soil. Sqm 100 35 3500 2 1.6/B-1 Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5 m, disposed earth to be levelled and neatly dressed : All kinds of soil Cum 20 175 3500 3 1.8/B-1 Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils Cum 20 178 3560 4 1.25/B-1 Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth, consolidating each deposited layer by ramming and watering including lead up to 50 meter and with all lift. Cum 40 64 2560 5 1.28/B-1 Surface dressing of the ground including removing vegetation and inequalities not exceeding 15cm deep and disposal of rubbish lead upto 50mtr. and lift upto 1.5Mtr. All kind of soil. Sqm 1000 0 9 90000 6 3.1.4/B-3 Providing and laying in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering - All work up to plinth level. M10 grade Nominal Mix1: 3: 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size). Cum 5 3847 19235 7 3.3.1/B-3 Providing and fixing up to floor three level pre cast cement concrete string or lacing courses, copings, bed plates, anchor blocks, windows sills, shelves, louvers steps, staircases, etc. including carriage, hoisting and setting in position with cement mortar 1:3 (1-Cement:3- coarse sand) cost of required centering and shuttering and finishing smooth with 6 mm thick cement plaster 1:3 (1-Cement:3-fine sand) on exposed surface, including all T & P, curing etc. complete : M15 grade Nominal Mix1: 2: 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size). Cum 5 6987 34935 RajKaj Ref No.: 12958603 8 5.1.2/B-5 Brick masonry with F.P.S. bricks of class designation 75 in foundation and plinth with bricks Cement mortar 1 : 6 (1 cement : 6 coarse sand) cum 5 4263 21315 9 5.2.2/B-5 Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in :Cement mortar 1 : 6 (1 cement : 6 coarse sand) cum 5 4990 24950 10 6.1.6/B-6 Random Rubble stone masonry for with hard stone in foundation and plinth in Cement Sand mortar above 30 CM thick wall in: Cement Mortar 1:6 ( 1-Cement : 6-Sand). Cum 5 2838 14190 11 6.2.6/B-6 Random Rubble stone masonry with hard stone in superstructure above plinth level and upto five level above 30cm. thick walls in : Cement Mortar 1:6 ( 1-Cement : 6-Sand). Cum 10 3479 34790 12 6.17.3/B-6 Supplying and fixing in walls machine cut and polished stone shelves, tands and in CM 1:3 with machine cut edges : Kota stone minimum 30mm thick. Sqm 10 609 6090 13 7.5.1/B-7 Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. Jhunjhunu / Jalore (Red/Choclate/Black/Pink Colour) Up to 1500 Cm2 Tiles Sqm 5 1993 9965 14 7.12/B-7 Providing and fixing 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shades glazed tiles confirming to IS : 13753 & IS :15622 of size 200mm x 300mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). Sqm 10 674 6740 15 7.13/B-7 Providing and fixing 1st quality MAT finished ceremic tile size 300x300mm confirming to IS : 13755 and IS : 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (including the cost of cement mortar bed Sqm 10 748 7480 16 7.18.2/B-7 P & F 1st qualityVitrified Porcelain Polished tiles on floor, skirting and steps etc.in different sizes (thickness to be specified by manufactuer) with water absortion less than 0.08% and conforming to IS 15622 of approved make in all colour and shade, laid with 20 mm thick CM 1 : 4 including grounting the joints with white cement and matching pigment etc complete. size 600 mm X 600 mm Sqm 100 911 91100 17 8.13.3.1/B8 Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 marked using Phenol formal, dehydreresin in glue both sides with approved steel fittings complete as per Annexure ‘A’: 35mm thick Sqm 50 1991 99550 RajKaj Ref No.: 12958603 commercial veneer both side 18 8.24/B-8 Providing and fixing 18 mm thick, 150 mm wide pelmet of flat pressed 3 layer or graded wood particle board medium density grade I, IS : 3087 marked including top cover of 6 mm commercial ply wood conforming to IS: 303 BWR grade, nickel plate MS 20 mm dia curtain rod with nickel plated bracket including fixing with 25x3 mm MS flat 10 cm long all complete Mtr. 20 341 6820 19 8.25.2/B-8 Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., wherever necessary complete: 20 mm Mtr. 20 266 5320 20 8.33/B-8 Providing and fixing Almirah lock (50 to 70 mm size) of approved make without pair of handles for door with necessary screws etc complete as per direction of Engineer-in-charge. Each 5 150 750 21 9.1 /B-9 Structural steel work in single section fixed with or without connecting plate including cutting, hoisting ( height upto 10 m), fixing in position and applying a priming coat of approved steel primer all complete. Kg. 100 72 7200 22 9.26/B-9 Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20x3mm with suitable screw at not exceeding 150mm distance. Sqm 50 617 30850 23 9.27/B-9 Providing and fixing Square bars or other flat welded towindow, ventilatiors etc. Kg. 10 65 650 24 9.37/B-9 Providing and fixing concertina coil fencing with required dia 610 mm (having 15 nos. round per 6 metre length) up to 3m height of wall with existing angle iron Y shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. stud tied with GI staples and GI clips to retain horizontal including necessary bolts or GI barbed wire tied to angle iron all complete as per direction of Engineer In Charge with reinforced barbed tape (R.B.T.)/Spring core(2.5 mm thick) wire of high tensile strength of 165 kg/sq.mm with tape (0.52 mm thick) and weight 43.478 gm/metre (Cost of MS angle, CC block shall be paid extra) Mtr. 50 266 13300 25 9.39/B-9 Providing and fixing of double leaf steel shutter for cupboard,the frame is made of pressed steel ISI section 80x25 mmx1.25 mm thick with 1.00 mm MS sheet to spot welded including holdfasts of 15x3mm, MS oxidized fittings such asbutt hinges, sliding doors bolts, handles, tower bolts and twinpeg etc complete including applying priming coat of approved steel primer of red oxide zinc chromate and spray painting inapproved shade with deco paint of approved quality complete as per direction of Engineer In Charge Sqm 5 3895 19475 26 10.1.1/B-10 Providing corrugated G.S. sheet roofing including vertical /curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including Sqm 20 904 18080 RajKaj Ref No.: 12958603 cutting to size and shape whenever required. 1.00 mm thick with zinc coating not less than 275 gm/m2 27 10.16/B-10 Stone slab roofing on ground floor with fine grained stone slab from approved quarry including filling of joints of parapet and slab on both sides in cement sand mortar 1:4, with ceiling pointing in cement sand mortar 1 : 3 complete as per specification and instruction of Engineer In Charge Sqm 40 1648 65920 28 10.17/B-10 Grading roof for water proofing treatment with water proffing compound a) 10.17.1 Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) Cum 5 4483 22415 b) 10.17.2 Cement mortar 1:3 (1 cement : 3 coarse sand) Cum 5 5841 29205 29 10.22/B-10 Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10mm and down gauge) including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : Mtr. 20 111 2220 30 11.3.1/B-11 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, making of lines or groove etc complete but excluding the cost of nosing of steps etc. complete. 40mm thick with 20mm thick nominal size aggregate. Sqm 50 277 13850 31 11.5/B-11 Cement plaster in skirting and/dado 18 mm thick with cement mortar 1:3 (1 cement : 3 course sand) finished with a floating coat of neat cement including rounding of junctions with floor Sqm 5 284 1420 32 12.3.2/B-12 Plaster on new surface on walls in cement sand mortar 1:6 including racking of joint etc. complete fine finish : 20mm thick. Sqm 20 190 3800 33 12.31/B-12 Pointing on stone masonary in cement sand mortar 1:3 (1-Cement:3-Sand) : 0 a) 12.31.1 Flush / Ruled/ Struck or weathered pointing. Sqm 50 124 6200 b) 12.31.3 Deep grooved pointing Sqm 100 220 22000 34 12.34.2/B12 White washing with lime to give an even shade including all scaffolding: Old work (two or more coats) including scraping old surface and repairing with whiting wherever necessary. Sqm 500 6 3000 35 12.37.2/B12 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding:Old work (one or more coats) including scrapping surface and necessary repairs. (b) Same colour Sqm 5000 11 55000 36 12.40.2/B13 Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding:Old work (One or more coats ) Sqm 500 40 20000 37 12.41.2/B12 Finishing wall with water proofing cement paint of approved brand and manufacture and or required shade to give an even shade including all scaffolding: Old work (One or more coats). Sqm 2000 20 40000 38 12.46.2/B12 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :One or more coats on old work. Sqm 100 34 3400 39 12.48.2/B12 French sprit polishing: One or more coats on old work. Sqm 10 57 570 40 13.1/B-13 Repairs to plaster of thickness 12mm to 20mm in Sqm 50 235 11750 RajKaj Ref No.: 12958603 patches ofarea 2.5 sq. metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 m lead With cement mortar 1 :4 ( 1 cement : 4 coarse sand) 41 13.4.1/B-13 Renewing glass panes,with putty and nails wherever necessary: Float glass panes of thickness 4 mm. Sqm 25 617 15425 42 13.15/B-13 Patch repair to cement concrete floor including digging out old floor in regular shape and removal of rubbish curing etc. complete in all respects. Sqm 10 317 3170 43 13.23/B-13 Repair of existing steel glazed doors, windows and ventilator, MS sheet door, garge doors, compound wall gates etc. by welding drilling complete include. Cost of welding rods and hire charge of welding meachine and TP etc complete Sqm 10 332 3320 44 13.24/B-13 Labour charges for repair to door / window without using anymaterial such as applying randha (finishing) tightening of bolts & screw etc. Sqm 50 220 11000 45 13.29/B-13 Repair to damaged RCC slabs, beams and columns etc for strengthening with cement mortar 1 : 2 in following steps :- (i) Choping losse and cracked concrete to required depth, cleaning the exposed surface of steel and concrete with wire brush and sand papering , cleaning of concrete surface with water as necessary and getting dried. (ii) Applying Epoxy primer on the exposed steel bars. (iii) Applying Epoxy hardener and resin mix (as per manufectureds specification) on concrete and steel bars with brush. (iv) Speading dry cement mortar 1 : 2 mix over epoxy treated wet surface and allow it to dry for one day. (v) Plastering the surface with cement sand mortar 1 : 3 upto depth of 30mm complete. (vi) Cure the plastered surface for 15 days, All work including scaffolding etc. complete in all respect. Sqm 5 1568 7840 46 13.32/B-13 Mechanised cleaning of storage tanks comprises of following 6 stage as mentioned below : (i) Mechanical dewatering (ii) Desalting removal of leftover dirty water and sludge with sludge pump (iii) Cleaning of wall, ceiling and floor by high pressure water jet with help of equipments which creates a pressure of 100-150 bar (iv) Removal of remaing sludge from floor with the help of industrial vacum cleaner. (v) Spraying of non toxic, bio degradable ecofriendly and bacterial agent certified by a govt approved laborary to disinfect the tank from all harmfull pathogens. The dose should be safe as per the UECD guidelines & 23 adopted on 17 th december 2001. (vi) Treatment of inside tank by exposing UV radiation to kill further suspended or floating bacteria if any a) 13.32.1 Upto 500 ltr. Ltr 1500 0 0.4 6000 b) 13.32.2 Above 500 ltr. to 1000 Ltr. Ltr 2000 0 0.35 7000 c) 13.32.3 Above 1000 ltr. Ltr 3000 0.3 9000 RajKaj Ref No.: 12958603 0 47 14.23.1/B14 Dismantling tile work in floors and roofs laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 meter lead: For thickness of tiles 10 mm to 25 mm. Sqm 100 20 2000 48 14.43.1/B14 Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes and including stacking of pipes within 50 meter lead : 15 mm to 40 mm nominal bore. Mtr. 100 41 4100 49 14.50/B-14 Dismantling of gully chamber of various sizes including CI grating with frame including stacking of useful materials near the site and disposal of unserviceable material within 50 meter lead including refilling the gap. Each 10 255 2550 50 15.4/B-15 Providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying : (i) after surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. (ii) laying second layer of Fiber glass cloth when the first layer is still green . Overlaps of joints of fiber cloth should not be less than 10 cm . (iii) Third layer of 1.5 mm thickness consisting of slurry of cement @ 1.289 kg/sqm mixed with water proffing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm. This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The entire treatment will be taken upto 30cm on parapet wall and tucked into groove in parapet all around (iv) fourth and final layer of brick tiling „with cement mortar or any other approved protective coarse. (which will be paid for separately) For the purpose of measurement the entire treated surface will be measured Sqm 50 372 18600 51 16.5.1/B-16 Providing and fixing glazing in aluminium door, window, vintilator shutters and partitions etc. with PVS/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineerin-charge (Cost. of aluminium snap beading shall be paid in basic item.) With glass panes of 4.0mm thickness (weight not less than 10.0 Kg/Sqm) as per IS : 2835. Sqm 10 791 7910 52 16.6.1/B-16 Providing and fixing double action hydraulic floor spring of approved brand and manufacture IS : 6315 marked, for doors including cost of cutting floors as required, embedding in floors and cover plates with brass pivot and single piece M.S. With stainless steel cover plate Each 5 1426 7130 53 1.2.2/S-1 P & F Indian type white glazed vitreous china 1st quality W.C. orissa pan (IS :2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor: Size 580x440mm. Each 10 3080 30800 RajKaj Ref No.: 12958603 54 1.3/S-1 P & F European type white glazed vitreous china 1st quality W.C pan (IS : 2556 Mark) with P or S trap including cutting and making good the wall and floor Each 10 2420 24200 55 1.4/S-1 P & F European type white glazed vitreous china 1st quality Double syphonic W.C (IS :2556 Mark) with P or S trap including cutting and making good the wall and floor Each 5 5198 25990 56 1.7.2/S-1 P & F water closet Seat Covers with brass hinges complete : Solid PVC (IS 2548 marked) grade-I White for EWC. Each 20 485 9700 57 1.20.2/S-1 P & F Low level Flushing Cistern of 10 litres capacity (IS:2556 mark) of approved make with complete fittings C.I. brackets duly painted, brass ball cock with ball, (IS:1703 mark) complete including cutting and making good the wall : PVC with PVC bend as per IS : 7231 Each 20 1291 25820 58 1.36.1/S-1 P & F WVC Wash basin (Ist quality IS:2556 Mark) of approved make with C.I. brackets duly painted 1 No. 15 mm C.P. Pillar cock (IS:8934 Mark) & 32 mm C.P. brass waste coupling of approved make, P.V.C Waste pipe with PVC nut 32 mm complete including cutting & making good the wall : Size 450 mm x 300 mm Each 10 2268 22680 59 1.38.9.3/S1 P & F Kitchen & Lab. Sink of approved make with C.I. brackets duly painted, 40 mm C.P. waste coupling, C.P. Brass chain with rubber plug, 40 mm G.I. waste pipe up-to floor level complete including cutting and making good the wall & floor : 1.0 mm thick stainless steel AISI -304 & IS 13983-1994 kitchen sink of approved make as per Engineer-incharge with large waste coupling. Overall size Bowl size (inches) (inches) 24 x 18 x 8 20x16x8 Each 5 5062 25310 60 1.42.2/S-1 P&F waste coupling with fitting of approved quality/ make : C.P. brass 40mm dia Each 25 218 5450 61 1.43.2/S-1 P&F waste pipe with all fitting PVC with PVC Nut 32mm Each 100 61 6100 62 1.45.1/S-1 P & F Looking Mirrors with P.V.C. frame of approved makeas per direction of Engineer-in-charge Size 500x400mm Each 20 351 7020 63 1.47.3/S-1 P&F towel rail or ring of approved quality /make: C.P. brass towel rail with bracket 450 x20mm. Each 10 296 2960 64 1.48.1/S-1 P&F Grating of approved quality/ make: Stainless steel sheet size 125mm dia Each 10 62 620 65 1.52.1/S-12 P&F Soap dish or tray of approved quality/ make C.P. brass Each 10 127 1270 66 1.55/S-1 P&F Bath shower of approved quality/ make 0 a) 1.55.1 C.P. brass fixed. Each 10 149 1490 b) 1.55.3 C.P. brass of Heavy & superior quality, revolving with adjustable key 150mm. Each 10 573 5730 67 1.58/S-1 Labour Charges for removing WVC pan: 0 RajKaj Ref No.: 12958603 a) 1.58.1 India/ Orissa pan Each 10 227 2270 b) 1.58.2 European W.C. Each 10 227 2270 c) 1.58.3 Flushing cistern Each 10 96 960 68 1.59/S-1 P&F Jet spray for water closet with C.P. copper tube flange of approved make Each 10 381 3810 69 2.1/S-2 P & F G.I. Pipes (Internal work) with G.I. fittings (IS:1239 Mark) & M.S. clamps including cutting and making good the walls and floors : Exposed on wall, 0 a) 2.1.1 15 mm dia nominal bore, B Class Mtr. 10 230 2300 b) 2.1.3 25 mm dia nominal bore, B Class Mtr. 10 360 3600 70 2.2/S-2 P & F G.I. Pipes (External work) with G.I. fittings (IS:1239 Mark) including trenching & refilling earth etc.: 0 a) 2.2.1 15 mm dia nominal bore, B Class Mtr. 10 190 1900 b) 2.2.3 25 mm dia nominal bore, B Class Mtr. 10 278 2780 c) 2.2.6 50mm dia nominal bore, B Class Mtr. 10 491 4910 d) 2.2.9 100mm dia nominal bore, B Class Mtr. 10 1064 10640 71 2.6/S-2 P & F Pillar Cocks (IS:8934 Mark) of superior quality and approved make : 0 a) 2.6.1 C.P. Pillar cock 15 mm dia nominal bore. Each 20 779 15580 b) 2.6.4 C.P. Pillar cock, Swan-neck with casted spout, 15mm nominal bore. Each 10 1246 12460 72 2.7/S-2 P & F Bib Cock (IS:8931 Mark) Superior quality of approved make : 0 a) 2.7.3 C.P. Brass bib cock, 15 mm nominal bore. Each 20 590 11800 b) 2.7.4 C.P. Brass bib cock Long body, 15mm nominal bore weight not less than 690 gm Each 10 783 7830 73 2.11.1/S-2 P & F Ball Cock (IS:1703 Mark) with Rod & P.V.C. Ball complete : Brass wt. 300 gm, 15 mm. Each 50 314 15700 74 2.12.1/S-2 P & F Inlet Connection (Angle Valves) Superior quality, of approved make, for Wash basin, Gyser etc. C.P. Inlet connection 15 mm Brass (IS:8931 marked). Each 20 501 10020 75 2.13/S-2 P & F 15 mm. Dia Connection pipe of approved quality/make: 0 a) 2.13.3 PVC pipe with C.P. Brass nuts up to length 450 mm. Each 20 101 2020 b) 2.13.4 PVC pipe with C.P. Brass nuts up to length 600 mm. Each 20 116 2320 c) 2.13.7 C.P. Brass Pipe with CP Brass nuts upto length 450 mm. Each 5 136 680 d) 2.13.8 C.P. Brass Pipe with CP Brass nuts upto length 600 mm. Each 5 176 880 76 2.15/S-2 P & F Full-way valve (IS:778 Mark) or wheel valve of approved make : 0 a) 2.15.1 Gun-metal 15 mm nominal bore. Each 20 227 4540 b) 2.15.3 Gun-metal 25 mm nominal bore. Each 10 529 5290 c) 2.15.6 Gun-metal 50mm nominal bore. Each 10 1464 14640 77 2.26/S-2 P & F PVC Storage Tank (IS:12701 marked indicating the BIS license No.) of approved make with cover, 25 mm dia 1 M long G.I. over-flow pipe & 25 Cm. long wash out pipe with plug & socket, including making connection etc. complete of approved design. 0 a) 2.26.3 500 litres capacity. Each 20 3920 78400 RajKaj Ref No.: 12958603 b) 2.26.5 1000 litres capacity. Each 20 7841 156820 c) 2.26.6 2000 litres capacity. Each 5 1568 2 78410 78 2.27/S-2 Hoisting Charges for each floor : 0 a) 2.27.1 For items 2.26.3 Each 20 110 2200 b) 2.27.2 For items 2.26.5 and 2.26.6 Each 25 157 3925 79 2.37/S-2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1 metre spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. (Internal work Exposed on wall) 0 a) 2.37.1 15 mm nominal size RM 50 191 9550 b) 2.37.3 25 mm nominal size RM 50 282 14100 80 2.38/S-2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (Concealed work including cutting chases and making good the walls etc.,) 0 a) 2.38.1 15 mm nominal size RM 100 279 27900 b) 2.38.3 25 mm nominal size RM 100 376 37600 81 2.39/S-2 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (IS 15778 : 2007 code) having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, this included jointing of pipes & fittings with one step CPVC solvent cement , trenching refilling & testing of joints complete as per direction of Engineer in Charge. (External work). 0 a) 2.39.1 15 mm nominal size RM 100 167 16700 b) 2.39.3 25 mm nominal size RM 100 262 26200 82 2.41/S-2 Labour Charges for Removing & Refixing the water Storage Tank of all sizes and including all Necessary fitting complete in all respect as per approved sample and direction of engineer in charge. Each 45 369 16605 83 2.44/S-2 Providing and fixing superior quality PVC Tank Cover complete as per approved by Engineer In Charge 0 a) 2.44.2 500 Lt. capacity Each 10 201 2010 b) 2.44.3 Above 500 Lt. capacity Each 10 216 2160 84 2.48.1/S-2 P&F Sluice valve of approved code IS 14846 : 2000 make 100 mm dia nominal bore Each 1 1017 5 10175 85 3.7.1/S-3 Labour charges for Removing S.W. pipes including breaking of joints & bed concrete, stacking of useful material at site within 50 Mtr. lead and disposal of unserviceable material within 0.5 Km. lead : 100 & 150 mm dia pipe Mtr. 50 23 1150 86 3.13/S-3 P & F Sand-cast Iron P or S Trap (IS:1729 make) of approved make. Each 10 927 9270 RajKaj Ref No.: 12958603 87 3.14/S-3 Labour charges for making connection of sewer line through main hole. Each 5 649 3245 88 3.16/S-3 P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2 .) approved quality /make including joining the pipe with solvent cement rubber ring and lubricant. 0 a) 3.16.2 75mm dia Mtr. 20 177 3540 b) 3.16.3 110mm dia Mtr. 50 282 14100 c) 3.16.4 160mm dia Mtr. 10 463 4630 89 3.16.5 Providing & Laying C.C. 1:3:6 (Stone Agreegate 20mm nominal size) all around PVC Pipe including 7.5 cm thick bed concerte [Width & Height = Dia of Pipe in CM+15CM] excluding cost of Pipe & Excavation of trenches etc. 0 a) 3.16.5.1 PVC pipe 110 mm dia Mtr. 50 325 16250 b) 3.16.5.2 PVC pipe 160 mm dia Mtr. 10 425 4250 90 3.17/S-3 P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: 0 i)a 3.17.1 Coupler, 75mm dia Each 5 87 435 b 110mm dia Each 5 108 540 ii)a 3.17.2 Reducer 110x75mm, 75mm dia Each 5 90 450 b 110mm dia Each 5 97 485 iii)a 3.17.3 Plain Tee, 75mm dia Each 5 114 570 b 110mm dia Each 5 187 935 iv)a 3.17.4 Door Tee, 75mm dia Each 5 177 885 b 110mm dia Each 5 213 1065 v)a 3.17.5 Door Y, 75mm dia Each 5 187 935 b 110mm dia Each 5 230 1150 vi)a 3.17.6 Double Y, 75mm dia Each 5 195 975 b 110mm dia Each 5 310 1550 vii)a 3.17.7 Double Door Y, 75mm dia Each 5 229 1145 b 110mm dia Each 5 391 1955 viii)a 3.17.8 Bend 45, 75mm dia Each 5 80 400 b 110mm dia Each 5 128 640 ix)a 3.17.9 Bend 87.5, 75mm dia Each 5 97 485 b 110mm dia Each 5 161 805 x)a 3.17.10 Door Bend (top side), 75mm dia Each 5 132 660 b 110mm dia Each 5 154 770 xi)a 3.17.11 Door bend (left &right), 75mm dia Each 5 158 790 b 110mm dia Each 5 195 975 xii)a 3.17.12 Vent Cowel, 75mm dia Each 5 43 215 b 110mm dia Each 5 56 280 xiii)a 3.17.13 Socket plug, 75mm dia Each 5 68 340 b 110mm dia Each 5 81 405 xiv)a 3.17.14 Door Cap, 75mm dia Each 5 44 220 b 110mm dia Each 5 62 310 xv)a 3.17.15 Pipe clip, 75mm dia Each 5 24 120 b 110mm dia Each 5 36 180 xvi) 3.17.16 WC connector with lipring, 110mm dia Each 5 213 1065 xvii) 3.17.17 WC connector bent type, 110mm dia Each 5 223 1115 xviii) 3.17.18 Plain floor trap, 110mm dia Each 5 230 1150 xviv) 3.17.23 P-Trap, 110mm dia Each 5 382 1910 RajKaj Ref No.: 12958603 xx) 3.17.24 Q-Trap,110mm dia Each 5 428 2140 xxi) 3.17.25 S-Trap, 110mm dia Each 5 535 2675 xxii) 3.17.26 Ring fitting, 110mm dia Each 5 108 540 xxiii) 3.17.27 Gully Trap, 110mm dia Each 5 561 2805 91 3.19/S-3 Construction of manhole in all type of soil inner size 90 X 60 Cm. 300 mm thick masonry in CM 1:6, 10 Cm. thick cement concrete 1:5:10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring, making channels, 80mm thick stone slab covering with 40mm thick M-15 grade C.C. flooring, Cement cover with frame of 450mm dia, earthwork etc. complete as per design including disposal of surplus earth within 50 mtr. lead. 0 a) 3.19.1 Depth up to 0.5 M Each 2 5489 10978 b) 3.19.2 Add extra over item 3.19.1 for every additional 0.10m depth above 0.5 m depth. Each 2 206 412 92 3.21.4/S-3 Construction of chamber in all type of soil with 300 mm thick masonry in CM 1:6 m,10 cm thick C.C. 1:5:10 in foundation, 20mm thick insider plaster in Cm 1:6, finished with floating neat cement, 50mm thick M-15 grade C.C. flooring , earthwork etc. complete as per design including disposal of surplus earth within a lead of 50 mtr. size 600 x 450mm depth upto 0.5 M to 1.0 M Cement cover with frame. Each 2 3628 7256 93 2.1.3/G-2 (Barmer BSR 2018) Providing services of 01 Nos. Superviser for daily supervision of above civil works including minor/nominal repair at residential and non-residential Building at Barmer and other at plant site Buildings. complete as per specification & directions of Engineer Incharge. Mont h 12 1040 0 124800 94 Item Rate Providing & Fixing G.I. Pipes fittings (Internal work and External work) with exsiting G.I. fittings & lines including cuting making good the walls and floor. Or including trencing and refilling earth etc. All fitting are approved quality and required T&P. 0 (a) Elbow:- 15 mm Each 20 36.2 724 (b) Elbow:- 25 mm Each 20 45 900 (c) Tee: 15 mm Each 20 39.4 788 (d) Tee: 25 mm Each 20 51.5 1030 (e) Socket:-15 mm Each 20 35.4 708 (f) Socket:-25 mm Each 20 41.2 824 (g) Union:-15 mm Each 20 47.8 956 (h) Union:-25 mm Each 20 66.8 1336 (i) Hex Nipple:15 mm Each 20 36.1 722 (j) Hex Nipple:25 mm Each 20 45.8 916 (k) Flange:15 mm Each 20 46.4 928 (l) Flange:25 mm Each 20 68 1360 (m) Plug heavy:15 mm Each 20 32.6 652 (n) Plug heavy:25 mm Each 20 35.8 716 (o) Check Nut :15 mm Each 20 35.7 714 (p) Check Nut :25 mm Each 20 41.1 822 (q) Solid plub(Black):15 mm Each 20 35.6 712 (r) Solid plub(Black):25 mm Each 20 41.9 838 (s) Cap plub(Black):15 mm Each 20 34.5 690 RajKaj Ref No.: 12958603 (t) Cap plub(Black):25 mm Each 20 38.9 778 95 Item Rate Providing & Fixing washer(leather /PVC) with brass spandle for bib cocks. Including all required materials and T&P for removing leakage of existing bib cocks. Each 20 40 800 96 Item Rate Providing & Fixing washer with brass spandle in CP brass long body, short body, mixture in existing fittings. Including all required materials and T&P for removing leakage of existing fittings. Each 20 95 1900 97 Item Rate Supply of drinking water of good quality at varios locations viz. Vidyut Vihar Colony, Rest House & Account Office including cost of water, transportation with all lead and lift, loading, unloading, hire charges of tanker, POL, T&P etc and all taxes, levies, duties etc. complete. KL 500 100 50000 98 Item Rate Supply of drinking water of good quality at Urja Nagar Colony, Barmer including cost of water, transportation with all lead and lift, loading, unloadin, hire charges of tanker, POL, T&P etc and all taxes, levies, duties etc. complete.
