Tender For Road Safety Work At Bangla Bazar Chauraha - Providing and applying 2 Component Cold Plastic Paint rolled on surfacing material solvent free, High build two pack seamless, tough, skid resistant, material which has property of attaining 1.5mm - 2.00mm thickness in single coat application Red (or as required colour) based on glass and colour retaining Acralic cross linking resin system for coloured road surfacing including surface cleaning and cost of all material etc. material laying process will be done manually. All-inclusive on bitumen surface, work shall carry out as per IRC 35-2015 clause 2.2), Glass beads as per BS6088 and 1.5 Reflective index(250 gram per sqm). 2 Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface.(15mm thick in yellow colour)Transverse Bar Marking with stricter compliance as per IRC:99-2018Providing and laying of hot applied thermoplastic compound 15 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 15 mm is exclusive of surface applied glass beads as per IRC:35 upto date (Thermoplastic marking of 300mm wide and 15mm height, at 1000mm apart (one set is of 6 strips). 15mm height is achieved through six application of thermoplastic, applied at an interval not less than 1 hour after previous layer gets solidified. Alternatively, made of Mastic Asphalt or any equivalent material which would provide 15mm high). The finished surface to be level, uniform and free from streaks and holes. 3 Providing and laying of hot applied thermoplastic compound 2.5 mm thick in white colour including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 upto date The finished surface to be level, uniform and free from streaks and holes. as Per SOR Ch-26 SI No.-2 4 Supply & fixing of Linear Delineator System (LDS) panels made of Micro Prismatic Retro Reflective sheeting type XI duly laminated on thin aluminium foil to a unique corrugated shape to provide Retro Reflection across wide range of observations and external angles. Eatch LDS panel should be of nominal length of 33 inch and each ridge shall be approximately 0.34 inch high. Each LDS panel is to be firmly fixed on existing concrete/brick work with 16 Nos fastner/ screw . SOR Ch-26 SI No.-9 5 The Solar studs shall be made of aluminium alloy and poly carbonate material which shall be absolutely weather resistant and strong enough to support a load of 13.635 kg tested in accordance with ASTM D4280. Its colour may be white, red, yellow, green or blue or combination as directed by the Engineer. Its water resistance shall meet the requirements of IP 65 in accordance with IS: 12063 : 1987 category 2 for protection against water ingress. The dimensions of solar studs shall not be less than 100 mm x 100 mm x 10 mm. It shall have super bright LEDs so as to provide long visibility from a distance of more than 800m. Its flashing rate shall not be less than 1 Hz. Its shaluld be able to give the prescribed performance in the temperature range of - 40oC to+55oC. Its life shall be not less than 3 Years. The rate shall include all materials, labour, equipments, fabrication, transportation, erection, installation and incidentals all complete as per direction of the Engineer-in-charge. as per SOR Ch-26 SI No.-16 6 Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC :67 upto date made of high intensity grade sheeting type-IV vide clause 801.3, fixed over aluminium sheeting 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with PCC M-25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing. The Retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International/Government Laboratory/ Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D 4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer / Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67 upto date. Legends , letters , numerals and borders etc should be as per MoRTH specification No-801.3.7 . Proof of the same in form of government report shall be uploaded while quoting tender. As per SOR ch-26 SI no.-18Cautionary Signs (Triangle shape)Hazard Marker (30 x 90cm Left/Riight) Object Hazard 7 Speed Limit sign 30kmph on side lane (Backing Board)(60cm circular) 8 Stop Sign(90cm high octagon 9 Major road ahead (60cm equilateral triangle)
