Construction Of Bus Stand At Nation Highway Norangdesar - Excavation of soil upto 1.5 m depth in foundation, trench, drain, tamping the bottom, pouring water, beautifying the sides, taking out the excavated soil, filling the empty spaces with soil again after filling the foundation and disposing the remaining soil upto a distance of 50 m, in ordinary/soft soil2 Putting excavated soil/sand in foundation and chair upto a distance of 50 m (lead) and leveling, pouring water and tamping with a trowel.3 Cement Concrete 1 cement : 4 gravel and 8 ballast / 1 cement, 3 gravel and 6 ballast stone of 40 mm nominal size put in the foundation, tamping and tamping etc. 1:3:6 (i) If hand broken gravel is used in place of 40 mm crusher broken stone aggregate, the same quantity will be payable but the rate of aggregate will be reduced by 30%. (ii) If Vibratar and mixer is not used, then 3% deduction should be made4 Cement Concrete 1 cement : 4 gravel and 8 gravel / 1 cement, 3 gravel and 6 gravel stone of 40 mm nominal size laying in the foundation, including tamping and tamping etc. 1:4:8 (i) If hand broken gravel is used in place of 40 mm crusher broken stone aggregate, the same quantity will be payable but the rate of aggregate will be reduced by 30%. (ii) If Vibratar and mixer is not used, then 3% deduction should be made5 Providing and laying in position specified grade of cement concrete for all R.C.C. structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement : 3 coarse sand) and making good the joints and cost of plastizers (if required) excluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix /Design Mix.Add extra for providing richer mixes respectively at all floor levels :Providing M-30 grade concrete instead of M-20 grade design mix.6 Centering and Shuttering with plywood or steel sheets including strutting, propping bracing both ways and removal of formwork for foundation, footings, strap beam, raft, bases of columns etc.7 Providing and fabricating reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding (including cost of binding wire) all complete upto floor five level.Thermo-mechanically Treated bars (Conforming of relevent IS code)8 Foundation and plinth first class brick masonry in cement-gravel 1:6 or 1:8 mortar including closing of side cracks and leveling. Cement mortar 1:69 Iron work in grills/gates etc. including cutting, mounting and fixing of flat cones, T and corrugated (channel) etc.10 Cement plaster on wall by mixing cement-gravel in 1:6 ratio and scraping joints and regular leveling for 14 days. 20 mm11 Providing and applying white cement based putty over plastered surface to prepare the surface even and smooth complete. New Plastered Surface (three or more coats)12 Finishing walls with Acrylic Smooth exterior paint of required shade including all scaffolding. New work (Two or more coat applied @ 1.67 Ltr./10 sq.m. over and including base coat of water proofing cement paint applied @ 2.20 kg/ 10 sq.m.).13 Providing and fixing stainless steel railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-Charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) :For stainless steel (Grade 304).14 Supply and installation of Multi Rib Proofing/cladding Sheet Manufacture out of0.50mm TCT (Total Coated Thickness) high tensile Zinc aluminum alloy coated galvalume steel (as per 150gsm zinc aluminum coated 550Mpa tuekd strength) confirming to IS: 1397/astm A-792 sheet to have wide pens 30mm high NB at 250 center and center width of 1020mm sheets be casted with regular modified polyester system on a continuous with line on center for face and with a polyester coating respectively sheet shall have proportionality with siphoned plate made to prevent leakage sheet shall be fixed by more of sell drilling lift tapping hot dip zinc coated hox head fasterner of size 12x14x55mm long. The sheet shall be supplied in cost one length and for a minimum up to 12mts with all scaffolding.15 Direction and Place Identification signs upto 0.9 sq.m size boardRetro-reflectorised Traffic SignsProviding and erecting direction and place identification retro-reflectorised sign asper IRC:67 made of encapsulated lens type reflective sheeting vide Clause 801.3.1. fixed over aluminum sheeting, 2 mm thickwith areanot exceeding 0.9 sq.m supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 x 450 x 600 mm, 600 mm below ground level as per approved drawing and MoRTH Specification Clause 801. Direction and Place Identification signs upto 0.9 sq.m size board16 Providing and fixing 25 mm thick non slippery reflective type designer paving tile with metallic hardening using 2 Kg/Sq. MTR made out of cement concrete of required grade, sizes of tile upto 300×300 mm manufactured with wet cast vibration system in two layers and laid over base of 20 mm thick cement mortar 1:4 using neat cement slurry including finishing of joints etc. complete :Using M-30 grade cement Concrete.17 Checkered precast cement concrete tiles 22 mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning etc. complete on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) :Dark shade using ordinary cement.18 Painting with aluminum paint of approved brand and manufacture to give an even shade Two or more coats on new work.:
