Tender For Supply And Installation Of Jungle Gym Items In Luv Kush Vatika Sarmathura , Parallel Bar/Push And Dip Station: - Size 1700 Mm X 600 Mm X 1200 Mm. Providing And Fixing Of Parallel Bar/Push And Dip Station Made From ‘B’ Class Gi Pipe Of 2.5 Mm Wa, sarmathura-Rajasthan

Tender For Supply And Installation Of Jungle Gym Items In Luv Kush Vatika Sarmathura , Parallel Bar/Push And Dip Station: - Size 1700 Mm X 600 Mm X 1200 Mm. Providing And Fixing Of Parallel Bar/Push And Dip Station Made From ‘B’ Class Gi Pipe Of 2.5 Mm Wall Thickness. Material – Pre Galvanized Mild Steel, Material Thickness: 3Mm. The Equipment Is Fixed On Ground With Cement Concrete And J Shaped Welded Bolts Of 18 Mm Thickness. The Gym Equipment Shall Be Finished Smooth With A Primer Coating Of At Least 60 To 70 Micron Thickness Using Exonoble/Berger Make Paints Or Its Equivalent Paints. M.S. Plate Of 280 Mm X 130 Mm X 5 Mm Thickness Is Used. The Holding Down/Fixing Of Gym Equipments Shall Be Embedded In Cement Concrete In The Ratio Of 1:2:4 (1Cement:2 Coarsesand: 4 Stone Agg. 20Mm Nominal Size). Equipment Must Be Made And Confirms With The Approved Standards Certified By And Certificates Are Mandatory Requires , Multi Horizontal Bar - Size: 1450Mm Length X 900Mm Width X 2360Mm Height Two Way System For Multiple Use With Growing Children. The Newly Designed Equipment With Modification With Old Single Bar At Middle For Becoming Multiple Activities Instrument In Building Upper Body Muscles Especially That Of The Back And Shoulder. Wide And Narrow Grips Provide For Various Permutations Of Popular Exercise Soft Handgrips For Dipping Using Your Own Body Weight. A Very Strong And Robust Exercise For Triceps, Shoulders And Back Muscles. Push Ups: Appropriately Heighted Rolled Bars That Relieve Unnecessary Stress From Wrist And Forearms. Allows User To Dip Lower For A More Complete Arm, Chest, Shoulder And Back Workout. Equipment Made To Meet En 16630 Specification - European Standard For Permanently Installed Outdoor Fitness Equipment. Epoxy Coating Of Paint To Prevent Any Damage From Extreme Weather Condition. Vertical Pipe 80Mm Nb Gi B Class Pipe And Chinning Bar Of 32Mm Nb C Class Gi Pipe Of 3.5Mm Wall Thicknessj Hooks System Used For Grouting For Higher Stability And Ease Of Installation. Fix With Concrete Slab. Non Fading Virgin Lldpe Makes All Plastic Components Sun Face Resistant. Equipment Must Be Made And Confirms With The Approved Standards Certified By And Certificates Are Mandatory Requires , Double Horizontal Bar: - Size 1200 Mm X 1100 Mm X 1800 Mm. Providing And Fixing Double Horizontal Bar Instrumental In Building Upper Body Muscles Especially That Of The Back And Shoulder Made Of ‘B’ Class Gi Pipe Of 2.5 Mm Wall Thickness. Wide And Narrow Grips Provide For Various Permutations Of Popular Exercise. Dips: Soft Handgrips For Dipping Using Your Own Body Weight. A Very Strong And Robust Exercise For Triceps, Shoulders And Back Muscles. Push Ups: Appropriately Heighted Rolled Bars That Relieve Unnecessary Stress From Wrist And Forearms. Allows User To Dip Lower For A More Complete Arm, Chest, Shoulder And Back Workout. Equipment Made To Meet En 16630 Specification - European Standard For Permanently Installed Outdoor Fitness Equipment. Epoxy Coating Of Paint To Prevent Any Damage From Extreme Weather Condition. Thick Galvanized Main Post Of 114 Mm Diameter. All Pipes Are Of 2.5 Mm Thickness. Self Lubricating Bearing For Maintenance Free Usage. Nylon Foot Pedals For Extended Life. J Hooks System Used For Grouting For Higher Stability And Ease Of Installation. Fix With Concrete Slab. Non Fading Virgin Lldpe Makes All Plastic Components Sun Face Resistant. Equipment Must Be Made And Confirms With The Approved Standards Certified By And Certificates Are Mandatory Requires , Triple Twister: -Size :- L 1700 Mm X B 1300 Mm X H 1300 Mm. Providing Triple Twister Equipment Made From ‘B’ Class Gi Pipe Of 2.5 Mm Wall Thickness Of Different Nb. Nb Stands For Nominal Bore Sizes I.E. Internal Diameter Of Pipe In Millimetres. The Center Pipe Is Of 100 Mm Nb Made From ‘B’ Class Gi Pipe Of 2.5 Mm Wall Thickness. The M.S. Round Plate Of 250 Mm & 10 Mm Thickness Is Welded At Bottom. The Standing Frame Of The Triple Twister Is Of 32 Nb Made From ‘B’ Class Gi Pipe Of 2.5 Mm Wall Thickness. The Handle Frame Of Double Twister Is 25 Nb. The Twister Plate Fitted On The Standing Frame Is Made Up Of M.S. Round Plate Of Size 300 Mm Diameter And 10 Mm Thickness. The Equipment Is Fixed On Ground With Cement Concrete And J Shaped Welded Bolts Of 18 Mm Thickness And Closing Caps Made From Top Quality Fiber Reinforced Plastic Material Which Is Of 2 Mm Thick. The Pins Used Are Made Up Of 25 Mm Ms Bright Material. The Bearings Used Are Of 6205Zz Permanent Lubricated Sealed Bearing Of Reputed Brand (Fag/Skf). High Tensile Steel With Galvanized Nuts & Bolts Are Used For Assembly. The Powder Coating Done With Pure Polyester Powder With 60 To 70 Micron Thickness. Equipment Must Be Made And Confirms With The Approved Standards Certified By And Certificates Are Mandatory Requires , Air Walker: - Size 1000 Mm X 300 Mm X 1200 Mm. Providing And Fixing Air Walker Made From ‘B’ Class Gi Pipe Of 2.5 Mm Wall Thickness. The Center Pipe Is Of 80 Mm Nb Made From ‘B’ Class Gi Pipe Of 2.5 Mm Wall Thickness, And The Bottom Support Of M.S. Round Plate Of 250 Mm Dia & 10 Mm Thickness Is Welded At Bottom. The Leg Movement Frame Is Of 40 Mm Nb Made From ‘B’ Class Gi Pipe Of 2.5 Mm Wall Thickness. The Handle Frame Is Of 25 Mm Nb Made From ‘B’ Class Gi Pipe Of 2.5 Mm Wall Thickness. To Join The Centre Pipe & Leg Movement Frame Seamless Pipe Of 60 Mm Dia & 3 Mm Thickness & 25 Mm Dia Solid Bar Is Used. The Bending M.S. Plate Is Used To Join The Centre Pipe & Leg Movement Frame Is Of 6 Mm Thickness. The Footrests Is Made From Frp/C.I./Aluminum Casting Material, Its Sizes Are 130 Mm X 300 Mm X 5Mm. For The Support M.S. Plate Of 280 Mm X 130 Mm X 8 Mm Thickness Is Used. Closing Caps Made From Top Quality Frp Material With 2 Mm Thickness. The Pins Used Are Made Up Of 25 Mm Diameter Bright Bar. The Bearings Used Are 6205 Permanent Lubricated Sealed Bearing Of Reputed Make. The Nut Bolts Used For Assembly Are Made From S.S. Material. The Serclips Used For Assembly Are Of 25 Mm Diameter. The Equipment Is Fixed On Ground With Cement Concrete And J Shaped Welded Bolts Of 18 Mm Thickness And Painting Is Done By Attractive Color Spraying After Proper Surface Treatment, Shot Blasting And Initial Coat Of Yellow Primer Surface Is Applied Before Top Coat. The Top Coat Is Done Using The Best Quality Brand Paint Or Duly Powder Coated. Equipment Must Be Made And Confirms With The Approved Standards Certified By And Certificates Are Mandatory Requires , Shoulder Wheel: - Size 9000 Mm X 900 Mm X 1200 Mm. Providing And Fixing Shoulder Wheel Made From ‘B’ Class Gi Pipe Of 2.5 Mm Wall Thickness. The Center Pipe Is Of 100 Mm Nb Made From ‘B’ Class Gi Pipe Of 2.5 Mm Wall Thickness, And Bottom Support Of M.S. Round Plate Of 250 Mm Diameter & 10 Mm Thickness Is Welded At Bottom. The Handle Movement Frame Is Of 25 Nb & 20 Nb Made From ‘B’ Class Gi Pipe Of 2.5 Mm Wall Thickness. To Join The Center Pipe & Handle Movement Frame Seamless Pipe Of 130Mm Dia & 3Mm Thickness Kis Used. The Equipment Is Fixed On Ground With Cement Concrete And J Shaped Welded Bolts Of 18 Mm Thickness. The Pins Used Are Made Up Of 25 Mm Dia Bright Bar. The Bearing Used To Permanent Lubricated Sealed Bearing Of Reputed Make. The Nut Bolts Used For Assembly Are Made From S.S. Material. The Serclips Used For Assembly Is Of 25 Mm Diameter. The Polyurethane Plastic Bush Is Used For Handling. The Gym Equipment Shall Be Finished Smooth With A Primer Coating Of At Least 40 Micron Followed By Epoxy Based Powder Coating With Polyester Powder Coating Of At Least 60 To 70 Micron Thickness Using Exonoble/Berger Make Paints Or Its Equivalent Paints. The Holding Down/Fixing Of Gym Equipments Shall Be Embedded In Cement Concrete In The Ratio Of 1:2:4 (1 Cement: 2 Coarse Sand: 4 Stone Agg. 20 Mm Nominal Size.) Equipment Must Be Made And Confirms With The Approved Standards Certified By And Certificates Are Mandatory Requires , Leg Press Double: - Size 1800Mm X 300 Mm X 1200 Mm. Providing And Fixing Leg Press Double Made From ‘B’ Class Gi Pipe Of 2.5 Mm Wall Thickness. The Center Pipe Is Of 100 Mm Nb Made From ‘B’ Class Gi Pipe Of 2.5 Mm Wall Thickness, And The Bottom Support Of M.S. Round Plate Of 250 Mm Diameter & 10 Mm Thickness Is Welded At Bottom. The Remaining Outer Frame Is Of 40 Mm Nb Made From ‘B’ Class Gi Pipe Of 2.5 Mm Wall Thickness. To Join The Centre Pipe & Outer Frame Seamless Pipe Of 130 Mm Dia & 3Mm Thickness Is Used. The Seats Are Fitted On The Outer Frame Is Made Up Of Frp Material Of Size 330 Mm X 330 Mm Of Thickness 3 Mm & M.S. Plate Of Thickness 5 Mm And Size 250 Mm X 200 Mm Is Used To Support It. The Footrests Is Made From Frp/C.I.I Aluminum Casting Material, Its Sizes Are 130 Mm X 300 Mm & 5 Mm Thickness. The Frame Of Footrests Consists Of 25 Nb Made From ‘B’ Class Gi Pipe Of 2.5 Mm Wall Thickness. Closing Caps Made From Top Quality Frp Material Which Is Of 2 Mm Thickness. The Inner Bushes Are Made From Seamless Pipe; Its Diameter Is 60 Mm & 8 Mm Thickness. The Pins Used In Are Made Up Of 25 Mm Diameter Hardened Bright Bar. The Bearings Used Are Of 6205 Permanent Anqle Don By Attractive Qolor Spravinq After Proper Surface Treatment, Shot Blasting And Initial Coat Of Yellow Primer Surface Is Applied Before Top Coat. The Top Coat Is Done Using The Best Quality Brand Paint Or Duly Powder Coated. To Join The Centre Pipe & Outer Frame Seamless Pipe Of 130 Mm Dia & 3 Mm Thickness Is Used. The Seats Are Fitted On The Outer Frame Is Made Up Of Frp Material Of Size 330 Mm X 330 Mm Of Thickness 3 Mm & M.S. Plate Of Thickness 5Mm And Size 250 Mm X 200 Mm Is Used To Support It. The Footrests Are Made From Frp/ C.I./Aluminum Casting Material; Its Sizes Are 130 Mm X 300 Mm & 5 Mm Thickness. M. S. Plate Of 280 Mm X 130 Mm X 5 Mm Thickness Is Used. Closing Caps Made From Top Quality Frp Material Which Is Of 2 Mm Thickness. The Inner Bushes Are Made From Seamless Pipe; Its Diameter Is 60 Mm & 8 Mm Thickness. The Pins Used In Are Made Up Of 25 Mm Diameter Hardened Bright Bar. The Bearings Used Are Of 6205 Permanent Lubricated Sealed Bearing Of Reputed Make. The Handles Used Are Of Rubber Grip. The Nut Bolts Used For Assembly Are Made From S.S. Material. The Bushes (Stopper) Used To Avoid The Collusion Made From Polyurethin Plastic Material Of 50 Mm Diameter. The Serclipsed For Assembly Are Of 25 Mm Diameter. The Equipment Is Fixed On Ground With Cement Concrete And J Shaped Welded Bolts Of 18 Mm Thickness And Painting Is Lubricated Sealed Bearing Of Reputed Make. The Handles Used Are Of Rubber Grip. The Nut Bolts Used For Assembly Are Made From S.S. Material. The Bushes (Stopper) Used To Avoid The Collusion Made From Polyurethin Plastic Material Of 50 Mm Diameter. The Serclipsed For Assembly Are Of 25Mm Dia Meter. The Foundation Pipes Are Embedded In C.C. Stock And Paintings. Equipment Must Be Made And Confirms With The Approved Standards Certified By And Certificates Are Mandatory Require , Horse Rider: - Size 1080 Mm X 500 X 1105 Mm. Providing And Fixing Horse Rider Made From ‘B’ Class Gi Pipe Of 2.5 Mm Wall Thickness. The Main Frame Of 60 Mm Made From ‘B’ Class Gi Pipe Of 2.5 Mm Wall Thickness And The Bottom Support Of M.S. Round Plate Of 250 Mm & 10 Mm Thickness Is Welded At Bottom. The Leg Movement Frame Is Of 40 Mm Made From ‘B’ Class Gi Pipe Of 2.5 Mm Wall Thickness. The Handle Frame Is Of 32 Mm Made From ‘B’ Class Gi Pipe Of 2.5 Mm Wall Thickness. The Footrests Is Made From Frp/C.I.I Aluminum Casting Material, Its Sizes Are 130 Mm X 310 Mm X 5Mm. For The Support M. S. Plate Of 280 Mm X 130 Mm X 5 Mm Thickness Is Used. Closing Caps Made From Top Quality Frp Material With 2 Mm Thickness. The Pins Used Are Made Up Of 25Mm Bright Bar. The Bearings Used Are 6205Zz Permanent Lubricated Sealed Bearing Of Reputed Make (Skf/Fag). High Tensile Steel With Galvanized Nut Bolts Are Used For Assembly. The Serclips Used For Assembly Are Of 25 Mm. The Powder Coat Is Done By Polyurethine & Epoxy Powder With 60 To 70 Micron Thickness Equipment Must Be Made And Confirms With The Approved Standards Certified By And Certificates Are Mandatory Requires , Cycling Instruments/Arm And Paddle Bike: - Size 1100 Mm X 500 Mm X 900 Mm. Providing And Fixing Cycling Instruments/Arm And Paddle Bike Made From ‘B’ Class Gi Pipe Of 2.5 Mm Wall Thickness. The Center Pipe Is Of 40 Mm Nb Made From ‘B’ Class Gi Pipe Of 2.5 Mm Wall Thickness. The Handles Are Made Up Of Casted Iron Material With Plastic Holding Grips. For Foundation Holes Pass Provision Is Provided. The Footrests Is Made From Aluminum Casting Material, Its Sizes Are 130 Mm X 300 Mm & 3 Mm Thickness. The Equipment Is Fixed On Ground With Cement Concrete And J Shaped Welded Bolts Of 18 Mm Thickness. The Seats And Bank Rests Are Fitted On The Outer Frames Are Made Up Of M.S. Sheet Of Size 280 X 130 X 5 Mm Thickness And Deep Drawn And Pressed In Tools And Dies To Have Uniform Radius Of 20 Mm With No Sharp Edges. The Pins Used Is Made Up Of 25 Mm Diameter Harden Low Carbon Steel. The Bearing Used Is Of “6205” Permanent Lubricated Sealed Bearing. The Nut Bolts Used For Assembly Are Made From S.S. Material. The Gym Equipment Shall Be Finished Smooth With A Primer Coating Of At Least 40 Micron Followed By Epoxy Based Powder Coating With Polyester Powder Coating Of At Least 60 To 70 Micron Thickness Using Exonoble/Berger Make Paints Or Its Equivalent Paints. The Holding Down/Fixing Of Gym Equipments Shall Be Embedded In Cement Concrete In The Ratio Of 1:2:4 (1Cement: 2 Coarse Sand: 4 Stone Agg. 20 Mm Nominal Size.). Equipment Must Be Made And Confirms With The Approved Standards Certified By And Certificates Are Mandatory Requires , Rowing Machine: - Size 1200 Mm X 1000 Mm X 920 Mm. Providing And Fixing Rowing Machine Made From ‘B’ Class Gi Pipe Of 2.5 Mm Wall Thickness. The Main Frame Is Of 80 Mm X 40 Mm & 40 Mm X 40 Mm Crc Pipe With 2 Mm Thickness. The Handle Frame Is Of 25 Nb Made From ‘B’ Class Gi Pipe Of 2.5 Mm Wall Thickness. To Join The Movement Frame To Main Frame Seamless Pipe Of 50 Mm Dia & 3 Mm Thickness Is Used. The Seats Which Are Fitted On The Main Frame Is Made Up Of High Quality Frp Material Of Size 330 Mm X 330 Mm Of Thickness 3 Mm & M.S. Plate Of Size 250 Mm X 200 Mm X 5 Mm Is Used To Support It. Closing Caps Are Made From Top Quality Frp Material Which Is Of 2 Mm Thickness. The Pins Used Are Made Up Of 17 Mm Diameter Hardened Bright Bar. The Bearings Used Are Of 6203 Permanent Lubricated Sealed Bearing Of Reputed Make. The Handles Used Are Of Rubber Grip. The Nut Bolts Used For Assembly Are Made From S.S. Material. The Bushes (Stopper) Used To Avoid The Collusion Made From Polyurethine Plastic Material Of 50 Mm Dia. The Serclips Used For Assembly Is Of 17 Mm Dia. The Equipment Is Fixed On Ground With Cement Concrete And J Shaped Welded Bolts Of 18 Mm Thickness And Painting Is Done By Attractive Color Spraying After Proper Surface Treatment, Shot Blasting And Initial Coat Of Yellow Primer Surface Is Applied Before Top Coat. The Top Coat Is Done Using The Best Quality Brand Paint Or Duly Powder Coated Equipment Must Be Made And Confirms With The Approved Standards Certified By And Certificates Are Mandatory Requires

INR 500 /-

INR 24000.0 /-

INR 12 Lakhs /-