Tender For Construction Of Composite Toilet At Judicial Building Teothar; 1 Excavation soil Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including dressing of sides and ramming of bottom disposal of excavated earth, lead up to 50m and lift up to 1.5m, disposed earth to be levelled and neatly dressed. (No extra lift is payable if work is done by mechanical means) All kinds of soil 2 C.C. upto plinth level Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level : With 40mm nominal size graded stone aggregate. 4.1.2.1 M-15 - Grade concrete 3 With 20mm nominal size graded stone aggregate.4.1.1.2M-20 – Grade concrete 4 RCC upto plinth Providing and laying in position specified grade of reinforced cement concrete (with 20mm nominal size graded stone aggregate) excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :5.1.1 M-20 Grade Concrete 5 RCC in walls, columns, pillars etc Reinforced cement concrete work (with 20 mm nominal size graded stone aggregate) in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, posts and struts etc. above plinth level and upto floor two level excluding cost of centering, shuttering, finishing and reinforcement: 5.2.1 M-20M-20 Grade Concrete 6 RCC in beams, floors, staircases etc Reinforced cement concrete work (with 20 mm nominal size graded stone aggregate) in beams, suspended floors, roofs having slope of any degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral staircases above plinth level and upto floor two level excluding the cost of centering, shuttering, finishing and reinforcement in concrete grade. 5.3.1 M-20 Grade Concrete 7 Reinforcement Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding including cost of binding wire all wastages and overlaps, couplers (overlaps shall be provided as per requirement of IS 13920 for ductile detaling IS 456 RCC Design & SP 34 Reinforcement detailing ) etc. complete . (Note:-1. Spacer bars (chairs) shall be paid separately as shown in the drawing and as per direction of engineer in charge.2. No extra payment shall be done for overlaps and/or couplers.3. Couplers shall be conforming to IS code on “Reinforcement Couplers for Mechanical Splices of Bars for Concrete Reinforcement - Specification”) 5.16.3 Cold twisted Cold twisted bars (CTD). 8 Centering and Shuttering Centering and shuttering in cluding strutting, propping etc. and removal of form for: 5.9.1 Upto plinth Foundations, footings, bases of columns, etc. for concrete upto plinth level 9 Above plinth upto 3.6 m height from plinth level 10 Suspended floors, roofs, landings, balconies and access platform. 11 Brick work fly ash bricks insuper structureBrick work with fly ash lime bricks (FALG Bricks) conforming to IS:12894-2002, in super structure above plinth level up to floor two level in :6.7.3 50 kg / cm2Having 50 kg / cm2 average compressive strength.6.7.3.2 CM 1:6 Cement mortar 1:6 (1 cement : 6 sand) 12 15 mm cement plaster 15 mm cement plaster on the rough side of single or half brick wall of mix 13.2.2 1:6 (1 cement : 6 sand) 13 15 mm cement plaster finished with a floating coat 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix13.5.1 1:3 (1 cement : 3 sand) 14 W.C. Indian type with flushing cistern Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100mm sand cast Iron P or S trap, UPVC P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : 17.1.1 Size 580x440mm White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests. 15 Urinal flat back half stall urinal with automatic flushing cistern Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass including painting of fittings and cutting and making good the walls and floors wherever required 17.7.1 Single half stall urinalSingle half stall urinal with 5 litre P.V.C. automatic flushing cistern. 16 Squatting plate with flushing cistern Providing and fixing one piece construction white vitreous china squatting plate with an integral longitudinal flushing pipe, white P.V.C. automatic flushing cistern, with fittings, standard size G.I. / PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I clamps and C.P.rasscoupling complete including painting of fittings and cutting and making good the walls and floors etc. wherever required :17.8.1 Single squatting plate Single squatting plate with 5 litre P.V.C. automatic flushing cistern. 17 Wash basin Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :17.11.2 630x450 mm flat back single pillar cock (china clay) White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap. 18 Polyethylene water storage tank Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank 19 C.P. brass long nose bib cock Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gm, 15 mm nominal bore. 20 C.P. brass angle valve for basin Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893115 mm nominal bore 21 Brass stop cock Providing and fixing brass stop cock of approved quality : 18.30.1 15 mm dia 15 mm nominal bore 22 Unplasticised PVC pipe Below ground Providing and laying below ground unplasticised PVC pipe to with stand working pressure of 4 kg/cm2 soild waste pipes confirming to IS:13592 and IS:4985 including jointing with seal ring confirming to IS :5282 leaving 10mm gap for thermal expansion all necessary fittings etc. complete. Excavation to be paid seperataly. 19.4.1110 mm dia110 mm diameter OD(min. wall thickness 3.2mm) 23 Cement concrete 1:3:6 all-round unplasticised PVC pipes Providing and laying cement concrete 1:3:6 (1 cement: 3 sand: 6 graded stone aggregate 20 mm nominal size) all-round PVC. pipes including bed concrete as per standard design:19.5.1110 mm dia110 mm diameter PVC. pipe 24 Unplasticised PVC pipe fittings Providing and fixing unplasticised PVC moulded fittings/ accessories for unplasticised Rigid PVC soil and waste pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.17.59.1.2 110 mm 110 mm 25 T with door Single tee with door 17.59.3.2 110 mm 110x110x110 mm 26 Bend Bend 87.50 17.59.5.2 110 mm 110 mm bend 27 P.V.C. waste pipe for sink or wash basin Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 17.64.1 Rigid Semi rigid pipe 17.64.1.1 32 mm 32 mm dia 28 Mirror ( Plastic Frame) Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shape with 6 mm thick hard board backing17.68.4 1500x450 mm Rectangular shape 1500x450 mm 29 CPVC pipes internal work Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittingsi/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge.18.6.2 Concealed Concealed work including cutting chases and making good the walls etc.18.6.2.2 20 mm 20 mm nominal outer dia .Pipes. 30 Stainless Steel Fitting of press fit type Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M-profile and with O-ring sealing gasket of EPDM material of required diaas per dirction of Engineer-in-Charge. Reducer Reducer 18.10.2.1 22.22 mm For 22.22 mm x 15.88 mm outer dia pipe 31 Elbow 90° Elbow 90° 18.10.3.2 22.22 mm For 22.22 mm outer dia Pipe 32 CPVC gate valve Providing and fixing CPVC gate valve with knob of approved quality. 18.13.1 25 mm dia 25 mm nominal bore 33 Panelled UPVC door shutter 24 mm thick Providing and fixing Panelled UPVC door shutter to existing door frames. 24 mm thick factory made UPVC door shutters made of styles and rails of a UPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (±0.1 mm) wall thickness. The lock rail made up of a UPVC hollow H section, section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. U cleats. The shutter frame filled with a UPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturers specification and direction of Engineer-in-charge. (For W.C. 34 Structural steel work built up sections Structural steel work using M.S. flats, angles, channels I-section, H-section etc. riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 35 M.S. sheet door and angle iron frame Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x5mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. 10.5.2 With flats braces Using flats 30x6mm for diagonal braces and central cross piece 36 Vitrified floor tiles nano polished Providing and laying vitrified floor tiles (without soluble salt) or printed (with soluble salt) Nano polished (Glossy finish) in different sizes with water absorption less than 0.05% and conforming to IS:15622 of approved make in all colours& shades, 1st quality/ premium quality in flooring laid on 20mm thick cement mortar 1:4 (1cement:4sand) including grouting the joints with white cement and matching pigments etc. omplete11.76.1Light shade Plain ivory light shade Size 600X600mm thickness 9-10mm 37 Dark shade Dark shade (terracotta) Size 600X600mm thickness 9-10mm 38 Ceramic glazed wall tiles Providing and fixing Ceramic glazed wall tiles 300x450 mm or more (having thickness 6 to 7 mm) of 1st quality conforming to IS: 15622 of approved make in all Colours& shades, except burgundy, bottle green, black laid on 12mm thick bed of Cement Mortar 1:3 (1 Cement: 3 sand)preprad same day when mortar is still green jointed with grey cement slurry @3.3 kg per sqm including pointing the joints with white cementand matching pigments etc., complete. 39 Acrylic distemper Distempering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound) content less than 50 grams/ltr of approved manufacturer, of required shade and colour complete, as per manufacturers specification. Two or more coat on new work.
