|
| 1 | Making of holein R.C.C. slab/wall/beams and masonary wall (width up to 450 mm) by core cutting machine complete as per direction of EIFromdiameter 100mm to 150mm |
| 2 | Filling available excavated earth (excluding rock) in trenches, plinth side of foundation etc. in layers not exceeding 20 cm. in depth , consolidatingeach deposited layer by ramming and watering including lead upto 50Mtr. and lift upto 1.5Mtr. |
| 3 | Carraige of Earth, Sand, Lime, Morrum manure or sludge For 5 KM |
| 4 | Providing and fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture as per direction of Engineer-in-charge of size 595 X 595 mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanizing @120 grams per sqm) consisting of main ‘T’ runner suitably spaced at joints to get required length and size of 24X38mm made from 0.33 mm thick (minimum) sheet, 1200mm centre to centre, and cross‘T’ of size 24X32mm made out of 0.33mm (Minimum) sheet, 1200mm long spaced between main ‘T’ at 600mm centre to centre to form a grid of 1200X600mm and secondary cross ’T’ of length 600mm and size 24X32mm made out of 0.33 mm thick (Minimum) sheet to be interlocked at middle of the 1200X600mm panel to form grid of size 600X600mm resting on periphery walls/partitions on a perimeter wall angle pre-coated steel of size (24X24X3000mm made of 0.40mm thick (minimum) sheet with the help of rawl plugs at 450mm centre to centre with 25mm long dry wall screws @ 230mm interval and laying 15mm thick densified edged calcium silicate ceiling tiles of approved texture in the grid including cutting /making opening for services like diffusers, grills, light fitting, fixtures, smoke detectors etc., wherever required, Main ‘T’ runners to be suspended from ceiling using 50 mm long M 6 dash fasteners, 6mm G.I. fully threaded rods with galvnised steel L cleat level adjusters of size 80x25x2mm, spaced at 1200mm centre to centre long main ‘T’ bottom exposed with 24mm of all T-sections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawing and as directed by engineer-in-charge. Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs)having area less than 0.30 Sqm.The calcium silicate ceiling tiles shall have NRC. Value 0.50 (Minimum), light reflection> 85% non-combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <= 0.043 w/m0KC. |
| 5 | P&F rigid PVC Pipe (IS:4985 mark) class II/ (4 Kg. /Cm2.) approved quality /makeincluding joining the pipe with solvent cement rubber ring and lubricant. |
| 6 | 160 mm dia |
| 7 | P&F rigid PVC pipe fittings (IS: 4985 mark) of approved quality /make including joining the pipe with solvent cement rubber ring and lubricant: |
| 8 | Coupler (socket) |
| 9 | 160 mm dia |
| 10 | Bend 87 .5 |
| 11 | 160 mm dia |
| 12 | Construction of tube-well from ground levels and upto 100 Meter depth and above to accommodate housing and assembly pipe of following sizes in all types of alluvium strata by percussion/ rotary drilling method and with gravel as per IS:4097-1967 and packing as per IS:2800 (Part I -& II) 1979 as amended upto date (the work includes the cost of gravel & its primary packing and packing during development, lowering of housing & strainer assembly pipes, with supply and wrapping of coir-rope, wherever necessary, for arresting fine sand particles. The work will not include cost of housing pipe and strainer pipe assembly and development work, but work would be completed after obtaining sand free water). |
| 13 | 250 mm dia Nominal bore. |
| 14 | Development of tube well as per IS specification using suitable compressor to give sand free water for required yield of the gravel packed tube well. |
| 15 | Supply of ERW M.S. black casing pipe ISI marked (IS:4270/1992) of grade Fe410 of following sizes at site of work. |
| 16 | 200 mm Nominal bore of pipe |
| 17 | Supply of strainer pipes made of ERW M.S. black pipe ISI mark of following sizes at the site of work including required size of slotting as per IS:8110-1985. |
| 18 | 200 mm Nominal Bore. |
| 19 | S & F tube well cover ofM.S.sheet (6mm thick) with nuts and bolts complete for casing size: |
| 20 | 200mm dia |
| 21 | S & F M.S. clamp, set of 50 ×6mm flat iron with nuts and bolts etc. for holding the riser pipe assembly of submersible pump set. |
| 22 | Providing & lowering of G.I. Pipes, flange pipe including rubber washer and nuts of8 mm dia complete in all respect I.S.1239 Marked. |
| 23 | B Class 50 mm dia |
| 24 | SITC of radial / mixed flow submersible motor pump sets ISI marked (IS:8034-1989) of approved make with required accessories including making connection suitable for T.W./ D.C.B./ Open well. The job includes lowering ofriser pipe, G.I./H.D.P.E. pipe with rope, cables, installation of complete fitting and accessories, jointing of electrical cables up to switch board. All labour for testing of submersible pumps set and supply of water to water mains, complete in all respect. 150 mm dia submersible pump have following HP rating, phase, head, minimum discharge. (Group-1) |
| 25 | 10.0 HP, 3-Ø, (93-200)Mtr, (240-60)LPM |
| 26 | P & F Full way Valve (IS: 778 Mark) or wheel valve of approved make Gun metal 50mm nominal bore) |
| 27 | Supply & Installation of Feeder Type panel board fabricated in 18 gauge C.R. sheet duly painted having cutter hammer or oil starter suitable upto 10.0 H.P. complete with main switch 30 Amp. Voltmeter & Amp. Meter of suitable rating Indicator single phase preventor complete capacitor, 3 Nos. Havaels fareling rewireable fuse unit with bakelite sheet as per design mounted on iron frames and fixed in cement concretge block. |
| 28 | P/Laying P.V.C./SLPE insulated & P.V.C. sheathed cable of 1.1 KV grade with aluminium conductor of IS:1554 P-I of Group1 of approved makein ground as per IS:1255 including excavation of 30cmx75cm size trench, 25 cm thick underlayer ofsand,IInd class bricks covering, refilling earth,compaction of earth, making necessary connection, testing etc. as required of size. |
| 29 | 6 Sqmm 3 Core Unarmoured. |
| 30 | 10 Sqmm 4 Core armoured. |
| 31 | NBSR ITEMS |
| 32 | 12 mm Toughened glass partition:- Providing, making and fixing in position Fixed 12mm toughened glass as fixed glass rom Floor to available Ceiling level for Partitions. The glass is to be fixed with patch fittings and all the edges of the glass have to be polished for a smooth finish. The work includes cost of all materials, approved hardware, making necessary template before toughening of glass and fixing the same as per site conditions to a neat finished work as per drawings and directions etc., complete |
| 33 | Providing & Fixing frameless fully glazed 12 mm. clear Toughened Glass Door (in one / two shutter) with floor mounted pivotted door spring hinges to shutters fitted with patch fittings &floors with plate & screws including cutting holes & mending good with cement mortar. Edge of glass to be polished as Shutter size : 900 mm. x 2100 mm. (one shutter) with 100 mm. x 500 mm. long \"C\" handles |
| 34 | GRC ARCH (TYPE A)Providing and fixing Glass Reinforced Concrete (G.R.C) ornamental Arch casted with \"Spray Mix\" concrete designof size 3500 *1350 mm(plus/minus 500 mm) as per approved, pattern, thickness (Border 40-50mm thick & Wall Thickness 15-20mm thick) and shade. The Panels should be made from ‘53 grade’ White Portland Cement manufactured by ‘JK Cement’ or \"Birla white\", White Quartz fine graded sieve Silica Sand, Alkali Resistant Glass Fiber manufactured by \"NEG Japan, Owen Corning ‘Saint Gobain’ or equivalent, Super Plasticizers manufactured by ‘Karochem’,BASF, or equivalent, Polymers manufactured by ‘Nova Polychem’ ,BASF,or equivalent and U.V resistant Synthetic inorganic pigments should be used for pigmentation manufactured by ‘Phenochem industries ,Bayferrox,or equivalent. The Panels casting shall take placein FRP mould or equivalent. The GRC Panels flexural strength average L.O.P should be above or equivalent to 6 N/mm² & M.O.R should be above or equivalent to 12 N/mm² for tests done on 28 days cured samples. The fixing of Panels should be done using ‘Dry fixing’ method onto structural support members i.e. R.C.C, Brick work or Red oxide Primer -paint or Epoxy primer -paint treated mild steel. The fixtures, fasteners and self- tapping screws to be used for dry fixing should be of HP/HILTI/KLIMAS/Fischer/Wurth/MUNGO. The quantity of fasteners or self-tapping screws shall be calculated in accordance to the weight of Panels and actual site fixing conditions. If there will be a requirement of Joint filling, then Elastomeric exterior grade paintable PU Sealant will be used. For final finishing of Panel one weather shield exterior grade water based diluted paint coat will be done if required. Vendors shall submit shop drawings of the same, the drawings to be duly approved by the Engineer in charge at site. APPROVED MAKE- Birla White, Unistone, Sanderson,Apgrc or equivalent. |
| 35 | Providing and laying machine cut, mirror polished, Italian Marble stone flooring laid in required pattern in linear portion of the building all complete as per architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm includingpointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc. |
| 36 | Providing , spraying and applying Oikas paint of approved shade and colour on wallsand coloumns.The job is inclusive of scaping,leveling and preparing the surface.Bicolour paint will be used. The wall surface has to duly prepared by removing thedamaged plaster and applying P.O.P to give a smooth surface as per approval of the Architect |
| 37 | Executingnewartworkintraditionaldesignwithtraditionaltechniqueof\"thikri\"workon walls, furniture, ceilings etc., as per approved design and pattern directed by the Architect. The artwork to be executed by higly skilled craftsman, and as approved by the Engineer in charge. |
| 38 | Executing new artwork in traditional design and method on walls using lustre paint/ Hand made natural paint or metallic lustrepaintofapprovedcolour,designandpatternasdirectedbytheArchitect.Theartworktobe executed by higly skilled craftsman and as approved by the Engineer in charge. |
