Tender For Mgnregs - Material Work - Supply Of Raw Materials, ambalappara-Kerala

MGNREGS - Material work - Supply of RAW materials, 1 SUPPLY OF RAW MATERIALS 2 QUARRY WASTE 3 Stone Aggregate(single size): 40 mm nominal size 4 Stone Aggregate(single size):20 mm nominal size 5 Stone Aggregate(single size): 10 mm nominal size 6 Stone Aggregate(single size): 06 mm nominal size 7 Fine sand (Zone IV) 8 Coarse sand (zone III) 9 gravel 5mm to 10mm 10 Stone for masonry work 11 Portland Cement 12 M.S. Tube 40 mm dia 13 Mild steel tubes hot finished welded type 14 Galvanised steel bolts & nuts 6 mm dia and 25 mm long round head with slots 15 Galvanised steel J or L hooks 8 mm dia 16 G.I Limpet washer 17 Bitumen washer 18 Mild steel round bar 12 mm dia and below 19 Mild Steel round bar above 12 mm dia 20 Mild steel sheets with bolts and nuts to rest on pintels 21 Iron pintels including weldded pin 22 Mild steel sheets for tanks 23 Mild steel hooks 24 Mild steel plate 25 Mild steel tubes electric resistant or induction butt welded 26 Welding by electric plant 27 Wire nails 28 Bright finished or black enameled mild steel butt hinges 100x58x1.90 mm 29 Bright finished or black enameled mild steel screws 40 mm 30 Bright finished or black enameled mild steel screws 20 mm 31 Powder coated M.S. butt hinges 100 mm X58 mm X 1.9 mm 32 Flats up to 10 mm in thickness 33 Galvanised wire mesh of average width of aperture 1.4 and nominal dia.of wire 0.63 mm 34 G.I Trafford profile sheet 0.35mm thick 35 Precoated Aluminium Traffored sheet 0.450 mm thick 36 Structural steel such as tees,angles,channels and RS Joists 37 Stainless steel screws 50 mm 38 Red oxide Zinc chromate primer 39 Precoated galvanised steel plain ridges 40 Stainless steel (Grade - 304) hollow section round/square tubes 41 Stainless steel bolts /square bar and plates 42 G.I pipe 40mm dia 43 GI plain washer thick 44 Twisted steel/deformed bars 45 Hire charges of Concrete Mixer 0.25 to 0.40 cum with Hopper 46 Vibrator (Needle type 40 mm) 47 Hire charge of 10 HP engine and pump set - Materials 48 wall form panel 1250x500 mm 49 Corner angle 45x45x5 mm 1.50 m long 50 100 mm channel shoulder 2.5 m long 51 Double clip (bridge clip) 52 Single clip 53 Wall form panel 1250x450xmm 54 Corner angle 45x45x5 mm 2.50 long 55 Column clamp 450x1070 mm 56 Prop 2 m (2-3.5m) 57 Adjustable telescopic prop 3 m (2.02-3.75m) 58 Beam clamp 300-380 mm (450-1070 mm) 59 Adjustable span ESO+SI (2.35-3.40) 60 Second class kail wood in planks 61 Second class kail wood in scantling 62 Hollock ballies 125 mm diameter 63 Solid blocks of size 30x20x20cm 64 Solid blocks of size 30x20x15cm 65 Hollow Blok of size 40x20x10cm 66 Interlocking C.C. paver block (80 mm thick, M-30) 67 PVC vent cowl 63 mm dia 68 PVC vent cowl 110 mm dia 69 Brass bib-cock-15 mm dia 70 PVC pipe 63 mm outer dia . 6kgf/cm2 71 PVC pipe 110 mm outer dia 6kgf/cm2 72 PVC pipe 25 mm outer dia . 12 kgf/cm2 73 PVC pipe 32 mm outer dia. 10Kgf/cm2 74 PVC Elbow 63 mm dia 75 PVC 45 degree Elbow 63 mm dia 76 PVC door Elbow 63 mm dia 77 PVC bend 63 mm dia 78 PVC Tee 63x63x63 mm dia 79 PVC Socket/coupling 63 mm dia 80 PVC Elbow 110 mm dia 81 PVC 45 degree Elbow 110 mm dia 82 PVC door Elbow 110 mm dia 83 PVC bend 110 mm dia 84 PVC Tee 110x110x110mm dia 85 PVC Socket/coupling 110 mm dia 86 PVC pipe 40 mm outer dia. 10kgf/cm2 87 PVC pipe 20 mm outer dia 10 kfg/cm2 88 PVC pipe 63 mm outer dia . 4kgf/cm2 89 PVC pipe 32 mm outer dia 6Kgf/cm2 90 PVC pipe 40 mm outer dia. 6kgf/cm2 91 PVC pipe 75 mm outer dia 6kgf/cm2 92 PVC pipe 110 mm outer dia. 4kgf/cm2 93 PVC pipe 160 mm outer dia. 4kgf/cm2 94 PVC Elbow 75 mm dia 95 PVC 45 degree Elbow 75 mm dia 96 PVC Socket/coupling 75 mm dia 97 PVC Reducer 63x50 mm dia 98 PVC vent cowl 75 mm dia 99 Vitreous China orrisa type w.c. pan size 580 mm 100 Brass stop-cock 15 mm dia 101 Flushing Cistern P.V.C. 10 lts capacity (low level) (white) (with fittings, accessories and flush pipe) 102 100 mm S.C.I. trap with vent heel 103 Black plastic seat (soild) with lid C.P.brass hinges and rubber buffers 104 Vitreous china pedestal type water closet 105 Stainless steel kitchen sink - without drain board 470x420 mm bowl depth 178 mm 106 C.I. bracket for wash basin and sinks 107 Polyethylene water storage tank with cover and suitable locking arrangemnet 108 Vitreous china flat back wash basin 550x400 mm 109 15 mm C.P.brass tap 110 C.P. brass waste 32 mm 111 Rectangular shape 453x357 mm Mirror with Plastic moulded frame 112 Rawl plug 50 mm (designation 10 nos) 113 PTMT - Towel Rail (600 mm) 114 Chromium plated Brass screws 25 mm 115 White Vitreous china 10 lit. (full flush) capacity controlled low level flushing cistern with all fittings 116 Factory made door frame size 50x47 mm with wall thickness 5 mm made of single piece extruded profile 117 35 mm thick factory made solid panel PVC door shutter of single piece extruded profile non decorative finished (Matt finished) 118 Float glass sheet of nominal thickness 4 mm (weight not less than 10 kg/sqm) 119 Aluminium T or L Sections 120 Hard board 6 mm thick 121 Powder coating 50 microns on aluminium sections 122 Neoprene / EPDM rubber gasket 123 Second class teak wood in scantling 124 200 mm Aluminium aldrop 125 Multi surface paint 126 Special primer (C.W) 127 Synthetic enamel paint in black or chocolate shade 128 Acrylic exterior paint 129 Premium acrylic emulsion of interior grade, having VOC content less than 50 gm/litre 130 Exterior primer 131 Epoxy paint 132 deharadun white lime 133 Vitrified floor tile 60x60 cm 134 Ceramic Glazed Tiles Ist quality 300 x 300 mm in all shades and designs of White, Ivory, grey, Fume Red brown etc. 135 Ceramic Glazed Tiles Ist quality minimum thickness 5 mm in all colours shades and designs except burgundy, bottle green black 136 Bamboo nails 137 Aracanut post 138 Royalty for good earth 139 Common burnt clay F.P.S. (non modular) bricks class designation 7.5

INR 3000 /-

INR 50000.0 /-

INR 60 Lakhs /-