Tender For Ananganadi Grama Panchayath ,Vendor Selection For Supply Of Various Materials For Mgnregs, Palakkad-Kerala

Tender For Ananganadi grama panchayath ,Vendor selection for supply of various materials for MGNREGS- 1 QUARRY WASTE 2 Stone Aggregate(single size): 40 mm nominal size 3 Stone Aggregate(single size):20 mm nominal size 4 Stone Aggregate(single size): 10 mm nominal size 5 Stone Aggregate(single size): 06 mm nominal size 6 Fine sand (Zone IV) 7 Coarse sand (zone III) 8 gravel 5mm to 10mm 9 Stone for masonry work 10 Portland Cement 11 M.S. Tube 40 mm dia 12 Mild steel tubes hot finished welded type 13 Galvanised steel bolts & nuts 6 mm dia and 25 mm long round head with slots 14 Galvanised steel J or L hooks 8 mm dia 15 G.I Limpet washer 16 Bitumen washer 17 Mild steel round bar 12 mm dia and below 18 Mild Steel round bar above 12 mm dia 19 Mild steel sheets with bolts and nuts to rest on pintels 20 Iron pintels including weldded pin 21 Mild steel sheets for tanks 22 Mild steel hooks 23 Mild steel plate 24 Mild steel tubes electric resistant or induction butt welded 25 Welding by electric plant 26 Wire nails 27 Bright finished or black enameled mild steel butt hinges 100x58x1.90 mm 28 Bright finished or black enameled mild steel screws 40 mm 29 Bright finished or black enameled mild steel screws 20 mm 30 Powder coated M.S. butt hinges 100 mm X58 mm X 1.9 mm 31 Flats up to 10 mm in thickness 32 Galvanised wire mesh of average width of aperture 1.4 and nominal dia.of wire 0.63 mm 33 G.I Trafford profile sheet 0.35mm thick 34 Precoated Aluminium Traffored sheet 0.450 mm thick 35 Structural steel such as tees,angles,channels and RS Joists 36 Stainless steel screws 50 mm 37 Red oxide Zinc chromate primer 38 Precoated galvanised steel plain ridges 39 Stainless steel (Grade - 304) hollow section round/square tubes 40 Stainless steel bolts /square bar and plates 41 G.I pipe 40mm dia 42 GI plain washer thick 43 Twisted steel/deformed bars 44 Hire charges of Concrete Mixer 0.25 to 0.40 cum with Hopper 45 Vibrator (Needle type 40 mm) 46 Hire charge of 10 HP engine and pump set - Materials 47 wall form panel 1250x500 mm 48 Corner angle 45x45x5 mm 1.50 m long 49 100 mm channel shoulder 2.5 m long 50 Double clip (bridge clip) 51 Single clip 52 Wall form panel 1250x450xmm 53 Corner angle 45x45x5 mm 2.50 long 54 Column clamp 450x1070 mm 55 Prop 2 m (2-3.5m) 56 Adjustable telescopic prop 3 m (2.02-3.75m) 57 Beam clamp 300-380 mm (450-1070 mm) 58 Adjustable span ESO+SI (2.35-3.40) 59 Second class kail wood in planks 60 Second class kail wood in scantling 61 Hollock ballies 125 mm diameter 62 Solid blocks of size 30x20x20cm 63 Solid blocks of size 30x20x15cm 64 Hollow Blok of size 40x20x10cm 65 Interlocking C.C. paver block (80 mm thick, M-30) 66 PVC vent cowl 63 mm dia 67 PVC vent cowl 110 mm dia 68 Brass bib-cock-15 mm dia 69 PVC pipe 63 mm outer dia . 6kgf/cm2 70 PVC pipe 110 mm outer dia 6kgf/cm2 71 PVC pipe 25 mm outer dia . 12 kgf/cm2 72 PVC pipe 32 mm outer dia. 10Kgf/cm2 73 PVC Elbow 63 mm dia 74 PVC 45 degree Elbow 63 mm dia 75 PVC door Elbow 63 mm dia 76 PVC bend 63 mm dia 77 PVC Tee 63x63x63 mm dia 78 PVC Socket/coupling 63 mm dia 79 PVC Elbow 110 mm dia 80 PVC 45 degree Elbow 110 mm dia 81 PVC door Elbow 110 mm dia 82 PVC bend 110 mm dia 83 PVC Tee 110x110x110mm dia 84 PVC Socket/coupling 110 mm dia 85 PVC pipe 40 mm outer dia. 10kgf/cm2 86 PVC pipe 20 mm outer dia 10 kfg/cm2 87 PVC pipe 63 mm outer dia . 4kgf/cm2 88 PVC pipe 32 mm outer dia 6Kgf/cm2 89 PVC pipe 40 mm outer dia. 6kgf/cm2 90 PVC pipe 75 mm outer dia 6kgf/cm2 91 PVC pipe 110 mm outer dia. 4kgf/cm2 92 PVC pipe 160 mm outer dia. 4kgf/cm2 93 PVC Elbow 75 mm dia 94 PVC 45 degree Elbow 75 mm dia 95 PVC Socket/coupling 75 mm dia 96 PVC Reducer 63x50 mm dia 97 PVC vent cowl 75 mm dia 98 Vitreous China orrisa type w.c. pan size 580 mm 99 Brass stop-cock 15 mm dia 100 Flushing Cistern P.V.C. 10 lts capacity (low level) (white) (with fittings, accessories and flush pipe) 101 100 mm S.C.I. trap with vent heel 102 Black plastic seat (soild) with lid C.P.brass hinges and rubber buffers 103 Vitreous china pedestal type water closet 104 Stainless steel kitchen sink - without drain board 470x420 mm bowl depth 178 mm 105 C.I. bracket for wash basin and sinks 106 Polyethylene water storage tank with cover and suitable locking arrangemnet 107 Vitreous china flat back wash basin 550x400 mm 108 15 mm C.P.brass tap 109 C.P. brass waste 32 mm 110 Rectangular shape 453x357 mm Mirror with Plastic moulded frame 111 Rawl plug 50 mm (designation 10 nos) 112 PTMT - Towel Rail (600 mm) 113 Chromium plated Brass screws 25 mm 114 White Vitreous china 10 lit. (full flush) capacity controlled low level flushing cistern with all fittings 115 Factory made door frame size 50x47 mm with wall thickness 5 mm made of single piece extruded profile 116 35 mm thick factory made solid panel PVC door shutter of single piece extruded profile non decorative finished (Matt finished) 117 Float glass sheet of nominal thickness 4 mm (weight not less than 10 kg/sqm) 118 Aluminium T or L Sections 119 Hard board 6 mm thick 120 Powder coating 50 microns on aluminium sections 121 Neoprene / EPDM rubber gasket 122 Second class teak wood in scantling 123 200 mm Aluminium aldrop 124 Multi surface paint 125 Special primer (C.W) 126 Synthetic enamel paint in black or chocolate shade 127 Acrylic exterior paint 128 Premium acrylic emulsion of interior grade, having VOC content less than 50 gm/litre 129 Exterior primer 130 Epoxy paint 131 deharadun white lime 132 Vitrified floor tile 60x60 cm 133 Ceramic Glazed Tiles Ist quality 300 x 300 mm in all shades and designs of White, Ivory, grey, Fume Red brown etc. 134 Ceramic Glazed Tiles Ist quality minimum thickness 5 mm in all colours shades and designs except burgundy, bottle green black 135 Bamboo nails 136 Aracanut post 137 Royalty for good earth 138 Common burnt clay F.P.S. (non modular) bricks class designation 7.5

Sr No	CorrigendumDate	Corrigendum	CorrigendumType	NewSubmissionDate
1	18-01-2025	Date extension	Date	21-01-2025

INR 3000 /-

INR 50000.0 /-

INR 50 Lakhs /-