supply installation commissioning of E&M equipment for installation of bore at Near 24 Block Old Rajender Nagar, DDA Site 1 New Rajender Nagar, Ganpati Mandir Budh Nagar, 15A Block WEA Karol Bagh, 5 A Block WEA Karol Bagh, WZ-164 Dasghara, Near Chi Park B500 wali Chaupal Pandav Nagar, 2151/31/2 Gali No-06 Chacha Tirath Ram Singh Park, Yadav Mohalla Near Shadipur Red Light New Patel Nagar.-Supply of sub. P/Set fitted with dynamically balanced impeller mounted on stainless steel shaft with protection sleeve having stage bowls of closed grained shorted Type impeller.The pump will be directly coupled to required wet type Induction Motor of speed 2900rpm suitable for operation on 3 phase 415 volt 50c/s., AC supply. Discharge:-200 LPM, Head: - 90 Mtr., OD:-150 mm, 7.5 HP/10 stageMake:BS / SU /Cromp / Approved make of DJB 2 Supply of Automatic LT Panel Board suitable for 415 Volts, 3 Phase, 50 HZ, 4 wire system for operation of up to 15 HP submersible set, made out of not less than 2 mm thick CRCA for load bearing members and 1.6 mm for doors of panel, Totally enclosed, dust and vermin proof, floor mounted type. The panel size 760 mmX 1360 mm X300 mm and having (1) 63 amp change over- 1 No (2) 63 A TPN MCCB -1 No (3) Amp meter 0-50 A- 1 No (4) Voltmeter 1 No (5) Amp & volt meter selector switches-1 set (6) Auto-manual + Light + control MCB TP 32 Amp- 1Nos each (7) CT -3Nos (8) Push button + ON/OFF light2 Nos each (9) 5 KVAR Shunt capacitor- 1 No (10) Aluminium Bus bar size 25 mm X 6 mm - 1set (11) 15 HP Star Delta starter (a) 32 Amp Power contactor-3 Nos (b) overload relay 14-23 A -1 No (C) Star delta timer- 1 NO ( d) QT Timer -24 Hours -1 No (e) Motor Protection relay flush mouting with display with thermal O/L , Short circuit, earth fault, Phase loss, unbalance, phase reversal, lockedrotor protection Make:- L&T/Protech-1 No. Make of accessories /components as per DJB approved. 3 Supply-Of M.S. Clamp of 600 mm Length, duly fabricated out-of 12.5 mm thick, 50 mm wide M.S.Plate for holding the Pipe of 50 mm dia. 4 Supply-Of G.I. Pipe 50mm dia, Medium-class, each of 3±3 Meters Long, duly threaded on both-ends, welded & fitted with G.I./ M.S. Flange of minimum thickness 6 mm on both ends with a Slot for Submersible-Cable. Welding of M.S Strips at both ends on flange.Make of Pipe: Jindal / TATA. 5 Supply of three core flat cable with bare bunched copper conductor insulated & sheathed with PVC for submersible pump motor with voltage grade upto 1100V of 6.0 sq mm. size in 100mtr. Roll.Make: Finolex / Havells/CCI 6 Supply-Of G.I. Bend 90o x 50 mm dia, having Flange at both-ends.HSN CODE:- 7307 7 Supply-Of Nut-Bolts, ½” dia of different size i.e. 1.5” & 2.5” Long, threaded of good quality. 8 Supply-Of Rubber-packing for 50mm dia Flange.HSN CODE:-4008 9 Supply-Of Bore-Cover Plate of Size: 200 mm dia, made out from 6 mm thick M.S.-Sheet in 2-Halves and a Circular-Hole of 50 mm dia in center with Locking arrangement by Nuts & Bolts. 10 Supply ofCanvas Hose Pipe 50 mm dia 30 Mtr long Make Jyoti/DJb Approved 11 Supply-Of Tail-piece of Medium-Class G.I.-Pipe 500 mm Long with one-end threaded, as per out-let of Pump and another-end flanged, as per size of G.I. Pipe 50 mm dia.Make of Pipe:Jindal / TATA. 12 Installation of submersible pump set with pipe and other accessories, Connection of cable, installation of electric panel, Grouting of electric panel digging and fixing the same with the help of CC and laying of GI pipe from bore to panel executing minor civil making electrical connection with cable as required size i/c watch and ward cartage, taking all safety measures all tools and tackles. Testing and commissioning of all E&M equipment on No load and full load conditions as per standard and full satisfaction of engineer-in- charge. This is a turnkey job and it further includes any left out items which may be required during execution of work will be firm responsibility & no extra payment will be paid.
