Renovation Of Gcda Planning Department- 1 DEMOLITION 2 15.52 : Dismantling of flushing cistern of all types (C.I. / PVC/ Vitrous China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead 3 od196199/2024_2025 : Dismantling wooden/plywood partitions/cupboards with veneer laminates of different heights, both fixed and moveable along with supporting frames if any, including stacking of useful materials near the site and disposal of unserviceable materials within 50 mtrs lead. 4 od196211/2024_2025 : Dismantling of vitreous china wall mount wash basin/urinal etc with bib cock/pillar cock, waste water pipe, stop angle valve and other supporting fittings including disposal of unserviceable waste within 50 mtrs lead. 5 od196213/2024_2025 : Dismantling of exposed PVC pipes of dia 40mm, 50mm, 75mm and 110mm from toilets, wash area, urinals, plumbing shaft etc. with elbows, joints, traps, vents etc. including disposal of unserviceable waste within 50 mtrs lead. 6 od196216/2024_2025 : Dismantling of water supply/drainage concealed PVC pipes of dia 40mm, 50mm, 75mm, 110mm from toilets,urinals, wash area etc. with elbows, joints, valves etc. including disposal of unserviceable waste within 50 mtrs lead. 7 15.7.4 : Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar 8 15.12.1 : Dismantling doors, windows and clerestory windows (steel or wood ) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead:Of area 3 sq. metres and below 9 15.12.2 : Of area beyond 3 sq. metres 10 15.23.1 : Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm 11 15.56 : Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. 12 15.60 : Disposal of building rubbish/ malba/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved 13 WALL MASONRY AND PLASTERING 14 6.4.1 : Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in:Cement mortar 1:4 ( 1 cement : 4 coarse sand) 15 6.13.1 : Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:3 (1 cement : 3 coarse sand) 16 13.4.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 coarse sand) 17 od196182/2024_2025 : Supplying and comminssioning of broken A A C blocks, no more than 10 cm size for raising the toilet floors level by 15 cm for concealed piping for drainages and sewages, includes and 30 mm P C C filling on top with 1:3:6 ratio (1 cement:3 coarse sand:6 graded stone aggregate 40 mm nominal size). Finishing the surface for tiling. Complete. 18 WATER PROOFING 19 22.3 : Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C. kitchen and the like consisting of : i) I course of applying cement slurry @ 4.4 Kg/ sqm mixed with water proofing compound conforming to IS: 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. ii) II course of 20 mm cement plaster 1:3 ( 1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.iii) III course of applying blown or residual bitumen applied hot at 1.7 kg per sqm of area. iv) IV course of 400 micron thick PVC sheet.(Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/ sqm. 20 SANITARY & CP FITTINGS, WATER SUPPLY AND DRAINAGE 21 50.17.1.2 : Supplying and fixing CP Towel rod 45cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge. 22 od196220/2024_2025 : Supply, installation and commissioining charges for double robe hook from Cera/Jaquar or equivalent manufacturer including, accessories, bolts/screws, washers,etc. as applicable, complete including making good the wall as per Architectural drawings and as relevant standards. 23 od196227/2024_2025 : Providing and fixing 110 mm floor trap with gratings 24 17.7.3 : Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps 25 17.10.1.3 : Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink with drain board510x1040 mm bowl depth 200 mm 26 17.28.1.1 : Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC. waste fittings complete.Semi rigid pipe32 mm dia 27 17.28.1.2 : Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC. waste fittings complete.Semi rigid pipe40 mm dia 28 17.78 : Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/6 litre (adjustable to 4 litre /8 litres), including seat cover, and cistern fittings, nuts bolts and gasket etc complete. 29 17.80 : Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx.size 610x390x370 mm having pre & post flushing with water ( 250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer - in-charge. 30 17.31 : Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 31 17.32.1 : Providing and fixing mirror of superior glass ( of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Circular shape 450 mm dia 32 50.17.1.5 : Supplying and fixing CP Health Faucet superior quality ( Jagur or equvalent make ) including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge. 33 18.50.1 : Providing and fixing C.P brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms.15 mm nominal bore 34 18.52.1 : Providing and fixing C.P brass stop cock ( concealed) of standard design and of approved make conforming to IS: 893115 mm nominal bore 35 18.7.2 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge.Internal work - Exposed on wall20 mm nominal outer dia pipes 36 18.7.3 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge.Internal work - Exposed on wall25 mm nominal outer dia pipes 37 18.7.4 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer -in-Charge.Internal work - Exposed on wall32 mm nominal outer dia pipes 38 18.8.2 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge.Concealed work, including cutting chases and making good the wall etc.20 mm nominal outer dia pipes 39 18.8.3 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge.Concealed work, including cutting chases and making good the wall etc.25 mm nominal outer dia pipes 40 18.17.1 : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore 41 18.17.1A : Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :20 mm nominal bore 42 50.18.8.5.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 40 mm pipe 6Kgf/cm2 43 50.18.8.6.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 6 kgf/cm2 44 50.18.8.8.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 75 mm pipe 6 Kgf/cm2 45 50.18.8.9.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2 46 50.18.9.15.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 40 mm dia 6 Kgf/cm2 - External work - Exposed on wall 47 50.18.9.16.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 6Kgf/cm2 - External work - Exposed on wall 48 50.18.9.18.1 : Providing and fixing PVC pipes including fixing the pipe with clamps/clips at 1.00 m spacing.This included jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 75 mm dia 6Kgf/cm2 - External work- Exposed on wall 49 50.18.9.19.1 : Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall 50 TILE & GRANITE WORKS 51 11.47.2 : Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer,in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 600x600 mm 52 od196197/2024_2025 : Providing and laying antiskid vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.<br>Size of Tile 600 x 600 mm. 53 11.49.3 : Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS : 15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 800x800 mm 54 11.48.2 : Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 600x600 mm 55 11.48.3 : Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg). including filling /grouting and finishing complete as per direction of Engineer-in-charge.Size of Tile 800x800mm 56 8.2.2.2 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm 57 8.2.2.1 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Granite of any colour and shadeArea of slab upto 0.50 sqm 58 PAINTING 59 13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer 60 13.83.2 : Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile including applying additional coats wherever required to achieve even shade and colour.Two coats 61 13.80 : Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 62 13.88 : Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 63 WINDOWS, DOORS & BLINDS 64 od196179/2024_2025 : Providing and installing roller blinds made of plastic fiber with acrylic coatong, for the windows of approved shade and pattern. Aluminium powder coated top and bottom rail, high strength reinforced plastic control unit.<br>Maximum size of any windows is up to 4.0 M length and 1.8 M height. Includes all the fittings, roller and operation mechanisms. 65 od196192/2024_2025 : Providing and fixing factory made PVC door frame and shutter including cost of all fittings, labour charges etc. complete (Approved data of CE LSGD vide circular dated 18.08.2016)OD-11, DSR 2016 1.4902 dtd. 05.06.2017. 66 9.84 : Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width form 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. 67 21.1.1.2 : Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron) 68 21.1.2.2 : For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron) 69 21.3.1 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness 70 od196223/2024_2025 : Providing and fixingtouch lock for aluminium sliding window with necessary screws etc. complete. 71 od196226/2024_2025 : Providing no staining water resistant clear silicon sealant in the gaps and voids around uPVC windows /aluminium clerestory windows at a max.5mm width and depth. Complete. 72 INTERIOR PARTITIONS 73 9.105.5 : Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wallwith suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre.The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channelof 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufactures specification and direction of engineer in charge all complete.66 mm overall thickness partition using 8 mm thick double skin multipurpose cement bonded wood particle board manufactured as per IS: 14276 with suitable cement bondedboard screws 74 21.1.1.2 : Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron) 75 od196206/2024_2025 : Providing and fixing glazing in aluminium partitions with 12 mm thick toughened glass and EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-Charge. (Cost of aluminium snap beading shall be paid in basic item) 76 od196212/2024_2025 : Providing and fixing in position 12mm clear float toughened Glass for naked glass partition and door. The work to include making necessary template for all the glasses, cutting the glass to correct size, making all the necessary holes, cuts, toughening, polishing the edges etc. The cost to include SS 304 top and bottom glass connectors and all the required hardwares. The approximate size of each glass will be 950 to 1000 mm x 2550mm to 2650mm as per site conditions. Complete. 77 21.18 : Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge ( Door handle, lock and stopper etc to be paid separately) 78 od196214/2024_2025 : Providing 25mm dia polished stainless steel finish back to back pull Handle, 400 mm length door handles for glass doors from Dorma/Hettich or equivalent manufacturer. 79 od196217/2024_2025 : Providing and fixing market first quality no-glue frosted privacy film in naked glass partitions and glass doors, height up to 3.0 mtrs. as per the Architectural detail. 80 od196219/2024_2025 : Providing and fixing toilet partitions with 700 mm door sizes width made of impact and anti bacterial 18 mm thick solid/woodgrain high pressure laminated sheets of exterior quality. Finished in Suede, approved shade, confirming to IS 2026 and as per the fire retardant BS- 476/97 Standard. This also details providing and fixing in position necessary hardware made out of stainless steel (grade- 304/316) & Aluminium grade 6063 alloy as per manufacturer’s specification and architects instructions like: Door Knob, toilet lock with indicator, Gravity hinge, Adjustable legs, Aluminium top rail and H profile door stopper, corner fastners and tower bolts with necessary screws. Complete. 81 od196221/2024_2025 : Providing and fixing toilet partitions (without division panel) with 700 mm door sizes width made of impact and anti bacterial 18 mm thick solid/woodgrain high pressure laminated sheets of exterior quality. Finished in Suede, approved shade, confirming to IS 2026 and as per the fire retardant BS- 476/97 Standard. This also details providing and fixing in position necessary hardware made out of stainless steel (grade- 304/316) & Aluminium grade 6063 alloy as per manufacturer’s specification and architects instructions like: Door Knob, toilet lock with indicator, Gravity hinge, Adjustable legs, Aluminium top rail and H profile door stopper, corner fastners and tower bolts with necessary screws. Complete. 82 od196222/2024_2025 : Providing and fixing HPL partitions with 700 mm door sizes width made of impact and anti bacterial 18 mm thick solid/woodgrain high pressure laminated sheets of exterior quality. Finished in Suede, approved shade, confirming to IS 2026 and as per the fire retardant BS- 476/97 Standard. This also details providing and fixing in position necessary hardware made out of stainless steel (grade- 304/316) & Aluminium grade 6063 alloy as per manufacturer’s specification and architects instructions like: Door Knob, Gravity hinge, Adjustable legs, Aluminium top rail and H profile door stopper, corner fastners and tower bolts with necessary screws. Complete. 83 od196224/2024_2025 : Providing and fixing urinal/WC low height partitions made of impact and anti bacterial 18 mm thick solid/woodgrain high pressure laminated sheets of exterior quality. Finished in Suede, approved shade, confirming to IS 2026 and as per the fire retardant BS- 476/97 Standard. This also details providing and fixing in position necessary hardware made out of stainless steel (grade- 304/316) & Aluminium grade 6063 alloy as per manufacturer’s specification and architects instructions like: Adjustable legs for support, corner fastners with necessary screws. Complete. 84 od196225/2024_2025 : Providing and fixing panelling made of 18 mm thick pre laminated medium density boards having decorative laminated finish on one side and matching laminate on the other side. Supports are to be made by the same MDF boards in 50 mm wide planks at 600 mm c/c. Finished with 2 mm matching edgeband. Complete. 85 MDF WORKS : TABLES, CUPBOARDS AND STORAGE UNITS 86 od196181/2024_2025 : Providing and placing in position Executive table of size 2.30 x 0.90 mtrs made of 18 mm pre laminated MDF having exterior grade decorative laminate on one side and matching laminate on other side from market first manufacturer, shade, texture selected and approved by Architect. L shaped table having a 90 cm long side table storage on the extended side as per design, with 2 nos pull out drawers and 2 sliding doors. Edges finished with 2 mm thick edgeband of matching shade, factory pressed. 4 M power strip to be mounted and concealed electrical conduits to be provided as in design. SS 304 grade 18 inch sliders for draws, aluminium sliding bottom tracks, 35mm roller wheels, 150 mm long concealed cabinet door handles, screws, adhesives etc included. Complete. 87 od196185/2024_2025 : Providing and placing in position working table of size 2.00 x 0.90 mtrs made of 18 mm pre laminated MDF having exterior grade decorative laminate on one side and matching laminate on other side from market first manufacturer, shade, texture selected and approved by Architect. L shaped table having a 90 cm long side table storage on the extended side as per design, with 2 nos pull out drawers and 2 sliding doors. Edges finished with 2 mm thick edgeband of matching shade, factory pressed. 4 M power strip to be mounted and concealed electrical conduits to be provided as in design. SS 304 grade 18 inch sliders for draws, aluminium sliding bottom tracks, 35mm roller wheels, 150 mm long concealed cabinet door handles, screws, adhesives etc included. Complete. 88 od196188/2024_2025 : Providing and placing in position working table of size 1.80 x 0.75 mtrs made of 18 mm pre laminated MDF having exterior grade decorative laminate on one side and matching laminate on other side from market first manufacturer, shade, texture selected and approved by Architect. L shaped table having a 75 cm long side table storage on the extended side as per design, with 2 nos pull out drawers and 2 sliding doors. Edges finished with 2 mm thick edgeband of matching shade, factory pressed. 4 M power strip to be mounted and concealed electrical conduits to be provided as in design. SS 304 grade 18 inch sliders for draws, aluminium sliding bottom tracks, 35mm roller wheels, 150 mm long concealed cabinet door handles, screws, adhesives etc included. Complete. 89 od196190/2024_2025 : Providing and placing in position working table of size 1.50 x 0.75 mtrs, made of 18 mm pre laminated MDF having exterior grade decorative laminate on one side and matching laminate on other side from market first manufacturer, shade, texture selected and approved by Architect. L shaped table having a 75 cm long side table storage on the extended side as per design, with 2 nos pull out drawers and 2 sliding doors. Edges finished with 2 mm thick edgeband of matching shade, factory pressed. 4 M power strip to be mounted and concealed electrical conduits to be provided as in design. SS 304 grade 18 inch sliders for draws, aluminium sliding bottom tracks, 35mm roller wheels, 150 mm long concealed cabinet door handles, screws, adhesives etc included. Complete. 90 od196191/2024_2025 : Providing and placing in position working table of size 1.20 x 0.65 mtrs with storage units made of 18 mm pre laminated MDF having exterior grade decorative laminate on one side and matching laminate on other side from market first manufacturer, shade, texture selected and approved by Architect. Storage unit to be provided at one side with 3 drawers as in the design. Edges finished with 2 mm thick edgeband of matching shade, factory pressed. 4 M power strip to be mounted and concealed electrical conduits to be provided as in design. SS 304 grade 20 inch sliders for draws, pedestal locks for drawers, screws, adhesives etc included. Complete. 91 od196193/2024_2025 : Providing and placing in position working tables of different length and standard width of 55 cm, made of 18 mm pre laminated MDF with decorative laminate on one side and matching laminate on other side. Edges finished with 2 mm thick edgeband of matching shade. 50 x 50 mm GI square tube frames, black powder coated and neatly welded and supported to walls/partition frame work as in design. frame work to be covered with MDF board lipping of width 8 cm all around. Includes all the required screws, adhesive, labour etc. Complete. 92 od196195/2024_2025 : Providing, making and placing in position storage tall units having 50 cm depth made with market first quality brand 18 mm pre laminated MDF board having exterior grade decorative lamination on one side and balancing lamination other side and 12 mm pre laminated MDF board having exterior grade decorative lamination on one side and balancing lamination other side for backside boxing, finished with 2.0 mm thick matching shade edgebands heat pressed. 50mm skirting to be provided at the bottom. The rate includes all necessary SS 304 grade hardwares, 125 mm long selected model cabinet handles, soft closing cabinet hinges and 18 inch sliders if any, from Godrej/ebco or equivalent manufacturer, all as per Architectural drawing. Complete. 93 od196198/2024_2025 : Providing, making and placing in position cupboard units having 2.0 mtr length, 1.50 mtr height and 50 cm depth made with market first quality brand 18 mm pre laminated MDF board having exterior grade decorative lamination on one side and balancing lamination other side and 12 mm pre laminated MDF board having exterior grade decorative lamination on one side and balancing lamination other side for backside boxing, finished with 2.0 mm thick matching shade edgebands heat pressed. Sliding doors and 50mm skirting to be provided at the bottom as per design detail. The rate includes all necessary SS 304 grade hardwares, 150 mm long selected model concealed sliding cabinet door handles, sliding roller kit and aluminium tracks etc. from Godrej/ebco or equivalent manufacturer, all as per Architectural drawing. Complete. 94 od196200/2024_2025 : Providing, making and placing in position low height cupboard units having 2.55 mtr length, 0.90 mtr height and 50 cm depth made with market first quality brand 18 mm pre laminated MDF board having exterior grade decorative lamination on one side and balancing lamination other side and 12 mm pre laminated MDF board having exterior grade decorative lamination on one side and balancing lamination other side for backside boxing, finished with 2.0 mm thick matching shade edgebands heat pressed. Sliding doors with 18 mm thick MDF board frames in 50 mm width and 4mm float glass, fixed with aluminum beading to be provided. 50mm skirting to be provided at the bottom as per design detail. The rate includes all necessary hardwares, sliding roller kit and aluminium tracks etc. from Godrej/ebco or equivalent manufacturer, all as per Architectural drawing. Complete. 95 od196202/2024_2025 : Providing, making and placing in position cupboard units having 1.6 mtr length, 1.50 mtr height and 50 cm depth made with market first quality brand 18 mm pre laminated MDF board having exterior grade decorative lamination on one side and balancing lamination other side and 12 mm pre laminated MDF board having exterior grade decorative lamination on one side and balancing lamination other side for backside boxing, finished with 2.0 mm thick matching shade edgebands heat pressed. Sliding doors and 50mm skirting to be provided at the bottom as per design detail. The rate includes all necessary SS 304 grade hardwares, 150 mm long selected model concealed sliding cabinet door handles, sliding roller kit and aluminium tracks etc. from Godrej/ebco or equivalent manufacturer, all as per Architectural drawing. Complete. 96 od196203/2024_2025 : Providing, making and placing in position overhead cupboard units having 4.3 mtr length, 1.0 mtr height and 50 cm depth made with market first quality brand 18 mm pre laminated MDF board having exterior grade decorative lamination on one side and balancing lamination other side and 12 mm pre laminated MDF board having exterior grade decorative lamination on one side and balancing lamination other side for backside boxing, finished with 2.0 mm thick matching shade edgebands heat pressed. 2 track sliding doors to be provided as per design detail. The rate includes all necessary SS 304 grade hardwares, 150 mm long selected model concealed sliding cabinet door handles, sliding roller kit and aluminium tracks etc. from Godrej/ebco or equivalent manufacturer, all as per Architectural drawing. Complete. 97 od196205/2024_2025 : Providing, making and placing in position bottom cabinet units having 55 cm depth made with market first quality brand 18 mm pre laminated MDF board having exterior grade decorative lamination on one side and balancing lamination other side, finished with 2.0 mm thick matching shade edgebands heat pressed. 50mm skirting to be provided at the bottom. Pullout drawers with SS cutlery and plate basket to be mounted inside as per the drawing. The rate includes all necessary SS 304 grade hardwares, 125 mm long selected model cabinet handles, soft closing cabinet hinges and 16 inch sliders, from Godrej/ebco or equivalent manufacturer, all as per Architectural drawing. Complete. 98 od196207/2024_2025 : Providing, making and placing in position overhead cabinet units having 2.50 mtr length, 1.25 mtr height and 40 cm depth made with market first quality brand 18 mm pre laminated MDF board having exterior grade decorative lamination on one side and balancing lamination other side, finished with 2.0 mm thick matching shade edgebands heat pressed. Sliding doors with 18 mm thick MDF board frames in 50 mm width and 4mm float glass, fixed with aluminum beading to be provided. The rate includes all necessary hardwares, sliding roller kit and aluminium tracks etc. from Godrej/ebco or equivalent manufacturer, all as per Architectural drawing. Complete. 99 od196210/2024_2025 : Providing, making and placing in position toilet vanity counters with different lengths, 40 cm height and 50 cm depth made with market first quality brand 18 mm pre laminated MDF board having exterior grade decorative lamination on one side and balancing lamination other side, finished with 2.0 mm thick matching shade edgebands heat pressed. The rate includes all necessary SS 304 grade hardwares, 125 mm long selected model cabinet handles, soft closing cabinet hinges from Godrej/ebco or equivalent manufacturer,necessary scsrews, adhesive etc. all as per Architectural drawing. Complete. 100 od196215/2024_2025 : Providing, making and placing in position bottom cabinet units (inside the box under windows) having 55 cm depth made with market first quality brand 18 mm pre laminated MDF board having exterior grade decorative lamination on one side and balancing lamination other side, finished with 2.0 mm thick matching shade edgebands heat pressed. The rate includes all necessary SS 304 grade hardwares, soft closing cabinet hinges from Godrej/ebco or equivalent manufacturer, all as per Architectural drawing. Complete. 101 od196218/2024_2025 : Providing and placing in position working table of size 1.50 x 0.60 mtrs, made of 18 mm pre laminated MDF having exterior grade decorative laminate on one side and matching laminate on other side from market first manufacturer, shade, texture selected and approved by Architect. Edges finished with 2 mm thick edgeband of matching shade, factory pressed. Screws, adhesives and other necessary hardwares included. Complete.
