Tender For 2000161079-Serv-Amc Of Conveyor Belt Maint/Rep.Cy25 2000161079 10 10 40 Conv.Belt joint Hot Vulcanz. Fabric Belt 12 M2 150 Recapping Sheet(500 x 5) 70 M2 70 Conv.PulleyLagging-6mmThick Rubber Plain 7.5 M2 20 Conv.Belt/Components Cold Bonding TN9000 55 M2 30 Conv.Belt/Components Cold BondingTBS3000 75 M2 110 Conv.PulleyLagging-18mmThick Rubber_DG 125 M2 60 BeltJoint ST Cord HotVulcanizing 1600mm 14 NO 140 Rubber Lining 10mm Plain 10 M2 100 Conv.PulleyLagging-16mmThick Rubber_DG 12 M2 50 Conv.Belt ST Cord Hot Vulcanizing 800mm 7 NO 130 Rubber Lining 6mm Plain 100 M2 80 Conv.PulleyLagging-10mmThick RubberPlain 5 M2 10 Conv.Blt/Components Cold BondingTC310 90 M2 90 Conv.PulleyLagging-12mmThick Rubber_DG 150 M2 120 THICK CERAMIC CONVYOR PULLY LAGGING 42 M2 Email : yogeshwara.rao@amns.in Contact : Name : Gaddam Yogeshwara Rao Item Details : 1. Specification: a. Conveyor Belt Jointing requirement for Material Handling Equipment installed in Pellet Plants in Vizag Facility using Cold Vulcanizing or Hot Vulcanizing techniques for Fabric, HR Grade, <(>&<)> Steel cord Type Belts. b. Conveyor Pulley lagging requirement. c. Conveyor Belt Recapping requirement. 2. Scope: a. Conveyor Belt Jointing (Fabric, Heat Resistant <(>&<)> Steel Cord Belts) 1. Deployment of High Skilled Manpower Technician for Carrying out the Conveyor Belt Vulcanizing Joint by Cold Vulcanizing or Hot Vulcanizing as per the SOP. 2. The Vendor Site In-charge designated at site should be capable of assigning and ensuring the necessary skilled and trained Manpower deployment at area of Conveyor Jointing. 3. The site In-charge should ensure that the deployed technician must be of adept to carry out the Vulcanizing Jointing procedure as per the SOP for General Fabric conveyor belts, Old/New Conveyor Belts, Heat Resistant Grade Belts, Super Heat Resistant Grade belts, and belts vulcanizing techniques of Various shore hardness grade. 4. The Site In-charge Must Ensure that all the Joints being carried out are as Per SOP. 5. Before commencement of the belt Vulcanizing procedures, all necessary pre checks such as LOTO for the equipment, arrestors for counterweight, arrestors for conveyor belt ends being joined should be ensured with Engineer In-charge at work site. 6. Necessary Conveyor Belt Additional Looping requirement across the counterweights or take up should be given or ensured sufficiently referring to the TDS supplied by the conveyor Belt Vendor in concurrence with the AM/NS site In-Charge. 7. After carrying out the above step, recommended conveyor belt Splicing protocol to be followed as per the Sheets attached or Specific to the Conveyor Belt Make as Forwarded by the Belt Manufacturer. 8. The Site In-charge Must ensure that all the Tools required for performing the vulcanizing techniques as per the Protocol should be ensured. 9. The Vendor Site In-charge must document and report all the activities to the AM/NS Site In-Charge. 10. Exclusions: i. Belt Laying ii. Vulcanising Machine. iii. Jointing Kits for Fabric or Heat Resistant Grade Belts(Yokohama <(>&<)> Phoenix conveyor Belt) iv. Belt Clamps. v. Teflon Sheet Liners <(>&<)> corresponding Fastening Bolts <(>&<)> Nuts. b. Conveyor Pulley lagging requirement: 1. Deployment of Skilled Manpower Technician for Carrying out the pulley Lagging works for Conveyor belt. 2. Before commencement of the Pulley Lagging replacement, all necessary pre checks such as LOTO for the equipment, arrestors for belt counterweight, necessary Conveyor Belt Looping above the desired pulley should be Ensured referring to the in concurrence with the AM/NS site In-Charge and any deviation should be immediately appraised in concurrence with AM/NS site In charge. 3. Removal of old rubber lagging and carry out the Pulley Lagging Replacement to correct thickness and Type as requested by the AM/NS site In-Charge. c. For Conveyor Belt Re Capping: 1. All the safety checks of Equipment LOTO to be confirmed from AM/NS Page 2 of 8 ArcelorMittal Nippon Steel India Limited AM/NS PELLETS VIZAG Near Flyover, Scindia Road,Visakhapatnam,530004,Andhra Pradesh,India GSTIN 37AAACE1741P1ZG PAN AAACE1741P CIN U27100GJ1976FLC013787 Request for Quotation Number 6000126470 Date 30.12.2024 Submission Date 09.01.2025 Coll Req No AMNS deals with OEMs directly. We are very well equipped in every way to import / buy our goods directly from OEMs from any part of the world in a professional manner. We also use the vast global networks of our parent companies where necessary. We do not welcome any contact from intermediaries or Indian Agents of vendors. We assure all OEMs that you do not need to engage anyone to manage your transactions with us.Kindly respond to our RFQs and deal with our officials directly without involving any agents or intermediaries. Offers of vendors who insist on involving intermediaries in dealings with us could be disqualified. Contact for this RFQ null Sravan Lanka Contact Email sravan.lanka@ext.amns.in MATERIALS / SERVICES Please acknowledge receipt of the RFQ And provide your best quote for below given RFQ details. SR. No PR No. PR Item RFQ Item Services for line Item Quantity UOM Technical Details Other Details site in-charge before the commencement of Re Capping of the conveyor belt 2. Cleaning, grinding to be done on the damaged belt portion. 3. Applying suitable Recapping solution specific to the Grade and Application of Usage. 4. Fixing of patched piece. 5. Belt fastening with LION clamps to be done if required. General Terms: 6. Housekeeping of working place after completion of the job. 7. Shifting of tools <(>&<)> Material from Stores or tool room to the work place and shifting back to respective areas. 8. Shifting of unused material to stores and dispose the scrap to designated areas or at the areas designated by AM/NS within the Plant. d. Exclusions: i. Belt Laying ii. Vulcanising Machine iii. Joint Kits of Fabric, HR. iv. Belt Clamps v. Belt Fastening Kits. f. Important Terms: 1. Minimum Manpower: At-least 3 technicians to be present on daily basis. 2. All the skill set of the persons being deployed at site, necessary competency level of the technicians for carrying out various vulcanizing joints shall be authorized by the Contractor. 3. The contractor to improve the efficiency at work place shall upgrade necessary skills set of the Technicians deployed. 4. Manpower performance shall be evaluated internally by AM/NS. AM/NS reserves right to seek immediate replacement of the person on the grounds of safety, workmanship and other reasons affecting the plant performance. 5. Housekeeping after job completion i.e, removal of Job waste to the designated areas to be ensured by the vendor. 6. Daily log sheets of inspection to be signed by the Site In-charge /Area In-Charge on daily basis. 7. Bills should be enclosed with the Job measurement sheet, completion, and satisfactory report of Area Engineer along with the MIS report of the AMC without which bills shall be rejected. 8. Guarantee period to be specified and agreed. 9. In case of failure <(>&<)> Poor Workmanship is the cause after evaluation by AM/NS, Bill would not be paid for the case and Vendor should stand responsible to rectify immediately. 10. Contract date from 01-Jan-2025 to 31-Dec-2025. Page 3 of 8 ArcelorMittal Nippon Steel India Limited AM/NS PELLETS VIZAG Near Flyover, Scindia Road,Visakhapatnam,530004,Andhra Pradesh,India GSTIN 37AAACE1741P1ZG PAN AAACE1741P CIN U27100GJ1976FLC013787 Request for Quotation Number 6000126470 Date 30.12.2024 Submission Date 09.01.2025 Coll Req No AMNS deals with OEMs directly. We are very well equipped in every way to import / buy our goods directly from OEMs from any part of the world in a professional manner. We also use the vast global networks of our parent companies where necessary. We do not welcome any contact from intermediaries or Indian Agents of vendors. We assure all OEMs that you do not need to engage anyone to manage your transactions with us.Kindly respond to our RFQs and deal with our officials directly without involving any agents or intermediaries. Offers of vendors who insist on involving intermediaries in dealings with us could be disqualified. Contact for this RFQ null Sravan Lanka Contact Email sravan.lanka@ext.amns.in MATERIALS / SERVICES Please acknowledge receipt of the RFQ And provide your best quote for below given RFQ details. SR. No PR No. PR Item RFQ Item Services for line Item Quantity UOM Technical Details Other Details g. STANDARD PROCEDURE FOR COLD SPLICING: Overlapping of belt ends Minimum Overlap = Belt Width + bias Marking §Centre line to be marked by two tape method §Perpendicular line marking along with belt width by i. Triangular Method [3:4:5] ii. Arc Line Method iii. [and this is the base line for bias marking] §Bias = ½ of Belt Width §No. of steps = No. of Plies – 1 §Step Length = Splice Length ÷ No. of Steps §Splice Length = Belt Width [in normal case] §Mark bias line from baseline. §Mark step lines. Dressing §Care should be taken while cutting plies [avoid deep cutting] §While cutting the top and bottom cover rubber along with ply, an angle of 45º should be given. §Remove the cover rubber and ply layers one after other. §Remember step cutting should be done in the following manner: Tail End Side – top to be dressed. Head End Side – bottom to be dressed. Alignment of Belt Ends: Align both the belt ends as follows: §The centre line of both the belt ends are to be aligned in the same line. §Both the reference lines are parallel to each other. §The splice length should be maintained at both ends. §Clamp the belt rigidly in such a way that it can easily opened <(>&<)> closed. Buffing: §Any projection or loose particles should be removed from the spliced surface. §While buffing ply should not get damaged /rubber on the ply should not be melted. §Bevel portion should be done with twisted wire brush §The buffed (dressed) surface should be clean, rough, level and dry. Application of Solution: §Consumption of Solution <(>&<)> Hardener vFor 1M² of closed area require2Ltrs.of Solution <(>&<)> 2 Bottles of Hardener. §Apply 1st coat on both belt ends and allow it to dry completely [Drying time = 45 Mins. To 1 Hr.] §Apply 2nd coat [Final coat] on both belt ends and allow it to dry. Check with back side of finger, if there is a slight stickiness / tackiness then it can be closed [both belt ends] [Drying time = 15 - 20 Mins.]. §In heavy duty belts, because of coarse size of fabric, a third coating is required [wherever third coating is applied, second coating should be fully dried]. Closing <(>&<)> Hammering: While overlapping step by step, a hand pressing is required to remove the entrapped air from the steps and each step should be monitored to avoid overlapping. Once both the ends are overlapped, a 150mm channel piece should be inserted under the belt [in jointing area] and hammering should be done from center of the belt to both the edges without leaving any gap. In this process, total entrapped air will be escaped from the joint area. FINAL INSPECTION: In the cutting portion, if there is any overlap or gap the same should be buffed off or fill it off in both the sides so that no scraper will lift the joint while running. h. Standard Hot Joint Splicing Protocol for Fabric Belts: Fabric Belt Specification: Belt Width Page 4 of 8 ArcelorMittal Nippon Steel India Limited AM/NS PELLETS VIZAG Near Flyover, Scindia Road,Visakhapatnam,530004,Andhra Pradesh,India GSTIN 37AAACE1741P1ZG PAN AAACE1741P CIN U27100GJ1976FLC013787 Request for Quotation Number 6000126470 Date 30.12.2024 Submission Date 09.01.2025 Coll Req No AMNS deals with OEMs directly. We are very well equipped in every way to import / buy our goods directly from OEMs from any part of the world in a professional manner. We also use the vast global networks of our parent companies where necessary. We do not welcome any contact from intermediaries or Indian Agents of vendors. We assure all OEMs that you do not need to engage anyone to manage your transactions with us.Kindly respond to our RFQs and deal with our officials directly without involving any agents or intermediaries. Offers of vendors who insist on involving intermediaries in dealings with us could be disqualified. Contact for this RFQ null Sravan Lanka Contact Email sravan.lanka@ext.amns.in MATERIALS / SERVICES Please acknowledge receipt of the RFQ And provide your best quote for below given RFQ details. SR. No PR No. PR Item RFQ Item Services for line Item Quantity UOM Technical Details Other Details Type of Ply Ply Rating Number of Plies Top Cover Thickness Bottom Cover Thickness Cover Rubber Grade Total Thickness of the Belt Designing of Splice: Splice length as recommended by the belt manufacturer. As per DIN 22102, Standard splice length depends upon the ply rating (chart enclosed) Selecting the Vulcanizing Machine: Heater Plate: Length = Splice Length + 200mm Width = Belt Width + 150mm Cross Beam: -No. of Beams @ 1 beam for 250mm plate length. -No. of Cylinder per beam @ 1 cylinder for 250mm width of belt. PROCEDURE FOR HOT FABRIC SPLICING Belt free ends overlapping. Minimum overlap = splice length + bias Arrangement of vulcanizing machine (bottom set) and splicing boards. Marking on the belt end Center line to be marked by two tape method Perpendicular(reference) line marking along with belt width by Triangular Method [3:4:5] Arc Line Method [and this is the base line for bias marking] (Put Permanent marks on both the ends of ref line.) Bias = 0.3 x Belt Width (depending upon the bias angle of vulcanizing machine). No. of steps = No. of Plies – 1 Splice Length depends upon belt rating Mark bias line from baseline. Mark Joint configuration. Dressing Remember step cutting should be done in the following manner: Tail End Side – top to be dressed. Head End Side – bottom to be dressed Care should be taken while cutting plies [avoid deep cutting] While cutting the top and bottom cover rubber along with ply, an angle of 45º should be given. Remove the cover rubber and ply layers one after other. Alignment Align both the belt ends as follows: The centre line of both the belt ends are to be aligned in the same line. Both the reference lines are parallel to each other. The splice length should be maintained at both ends. Clamp the belt rigidly in such a way that it can be easily opened <(>&<)> closed. Matching and correction Buffing Any projection or loose particles should be removed from the spliced surface. While buffing ply should not get damaged / rubber on the ply should not be melted Bevel portion should be done with twisted wire brush Filling The buffed (dressed) surface should be clean, rough, level, moisture free and oil free. Apply 2 coats of hot vulcanizing solution on both dressed areas. Apply 2nd coat only after 1st coat is fully dried and allow 2nd coat also to be dried fully. Fix one layer of insulation compound / tie gum in one of the mating surfaces. Page 5 of 8 ArcelorMittal Nippon Steel India Limited AM/NS PELLETS VIZAG Near Flyover, Scindia Road,Visakhapatnam,530004,Andhra Pradesh,India GSTIN 37AAACE1741P1ZG PAN AAACE1741P CIN U27100GJ1976FLC013787 Request for Quotation Number 6000126470 Date 30.12.2024 Submission Date 09.01.2025 Coll Req No AMNS deals with OEMs directly. We are very well equipped in every way to import / buy our goods directly from OEMs from any part of the world in a professional manner. We also use the vast global networks of our parent companies where necessary. We do not welcome any contact from intermediaries or Indian Agents of vendors. We assure all OEMs that you do not need to engage anyone to manage your transactions with us.Kindly respond to our RFQs and deal with our officials directly without involving any agents or intermediaries. Offers of vendors who insist on involving intermediaries in dealings with us could be disqualified. Contact for this RFQ null Sravan Lanka Contact Email sravan.lanka@ext.amns.in MATERIALS / SERVICES Please acknowledge receipt of the RFQ And provide your best quote for below given RFQ details. SR. No PR No. PR Item RFQ Item Services for line Item Quantity UOM Technical Details Other Details 0.5mm insulation compound / tie gum for light duty belt 0.75mm insulation compound / tie gum for medium duty belt 1.0mm insulation compound / tie gum for heavy duty belt To form the edges, give 1 layer of (30mm wide) insulation strip in one of the dressed belt along both the edges Roll it properly for removing entrapped air. While closing step by step, a hand pressing is required to remove the entrapped air from the steps and each step should be monitored to avoid overlapping. While filling channel, one layer of tie gum/insulation compound should be given on plies in the channel and bevel portion and then fill cover compound. Ensure the cover grade of both mother belt and cover compound used are same. Arrangement of vulcanizing machine top part Vulcanizing: Curing temperature and time as recommended by the splicing kit manufacturer. Specific pressure on belt surface for Light duty 7 Kg. / cm² Medium duty 8 Kg / cm² Heavy duty 9 to 10 Kg / cm² Pressure to be increased gradually in stages Final Pressure at 145° C Cooling up to 70° C with the full pressure Removal of vulcanizing machine. Inspection of Joint: Check the splice visually and trim the overflow in the channel and edge area. STANDARD SPLICE LENGTH AS PER DIN 22102 i. Steel Cord Vulcanizing Procedure: Belt Specification: 1.Belt Width 2.ST Rating 3.Top Cover Thickness 4.Bottom Cover Thickness 5.Cover grades 6.Cord Diameter (d) 7.Cord Pitch (P ) 8.No. of Cords 9.Total Thickness of the Belt Designing of Splice: Number of steps and splice length as recommended by belt manufacturer. As per DIN 22131,splice length depends upon the cord diameter and pitch of cords (Chart enclosed) To decide the number of step -SG MIN = 1.2 + 0.1d -SG = [(p x n)/(n+1)]-d Where SG = tie gum thickness between the cords at the splice p= pitch of cords d= diameter of cords n= Number of steps (for single step, n=1) The condition, SG (SG)min, decides the number of steps for cord staggering. Selecting the Vulcanizing Machine: Heater Plate: Length = Splice Length + 300mm Width= Belt Width + 150mm Cross Beam: -No. of Beams @ 1 beam for 250mm plate length. -No. of Cylinder per beam @ 1 cylinder for 250mm width of belt. Steel cord kit checking Page 6 of 8 ArcelorMittal Nippon Steel India Limited AM/NS PELLETS VIZAG Near Flyover, Scindia Road,Visakhapatnam,530004,Andhra Pradesh,India GSTIN 37AAACE1741P1ZG PAN AAACE1741P CIN U27100GJ1976FLC013787 Request for Quotation Number 6000126470 Date 30.12.2024 Submission Date 09.01.2025 Coll Req No AMNS deals with OEMs directly. We are very well equipped in every way to import / buy our goods directly from OEMs from any part of the world in a professional manner. We also use the vast global networks of our parent companies where necessary. We do not welcome any contact from intermediaries or Indian Agents of vendors. We assure all OEMs that you do not need to engage anyone to manage your transactions with us.Kindly respond to our RFQs and deal with our officials directly without involving any agents or intermediaries. Offers of vendors who insist on involving intermediaries in dealings with us could be disqualified. Contact for this RFQ null Sravan Lanka Contact Email sravan.lanka@ext.amns.in MATERIALS / SERVICES Please acknowledge receipt of the RFQ And provide your best quote for below given RFQ details. SR. No PR No. PR Item RFQ Item Services for line Item Quantity UOM Technical Details Other Details Cover rubber Minimum Length of cover rubber = splice length + bias+ 100mm Minimum width of cover rubber = belt width +100mm Minimum thickness of cover rubber = mother belt cover thickness+ 0.5 mm Inter cord strip Height = cord diameter + 1mm Thickness = (SG) value Length = splice length x1.25 PROCEDURE FOR STEEL CORD SPLICE Belt free ends overlapping. Minimum overlap = splice length + Bias Arrangement of vulcanizing machine (bottom set) and splicing tables. Marking on the belt end. Center line to be marked by two tape method Perpendicular(Reference) line marking along with belt width by Triangular Method [3:4:5] Arc Line Method [this is the base line for bias marking] Bias = 0.3 x Belt Width (depending upon the bias angle of vulcanizing press) Splice Length depends upon ST Rating Mark bias line from baseline. Mark the joint configuration on both belt ends. Put reference marks on both the belt edges. Dressing While cutting the top and bottom cover rubber an angle of45° should be given. Remove top and bottom covers. Separate individual steel cords. Prepare steel cords in round shape, leaving a thin layer of bonding rubber around the cord. Aligning and arresting the belt ends Align both the belt ends as follows: The centre lines of both the belt ends are to be aligned in the same line. Both the reference lines are parallel to each other. The splice length should be maintained. Clamp the belt rigidly to the splicing table in such a way that it can easily opened <(>&<)> closed Buffing Buff slightly all the steel cords with special concave brush wheel. Buff the beveled belt edges and around 30mm of mother belt along the bias with twisted wire brush Filling: § Clean thoroughly the dressed belt ends and the adjacent location. § Apply 2 coats of steel cord solution on steel cords and buffed area(apply second coat only after drying the first coat thoroughly). § Lay suitable fabric cloth on bottom platen. § Lay silicon paper along the bias lines. § Lay uncured bottom rubber over the fabric cloth. § Care should be taken to keep the tie gum layer on top. § Mark <(>&<)> cut excess rubber. § Fix special bonding strips along the beveled edges on the belt. § Fix both ends of the belt to the uncured bottom rubber and hammer it for better fixing. § Mark the centre line and splice lines with knife on bottom uncured rubber. § Does the cord staggering as per standard with proper inter cord strips in between the cords. § A minimum gap of 15m.m to be maintained between the butt ends of opposite cords. Page 7 of 8 ArcelorMittal Nippon Steel India Limited AM/NS PELLETS VIZAG Near Flyover, Scindia Road,Visakhapatnam,530004,Andhra Pradesh,India GSTIN 37AAACE1741P1ZG PAN AAACE1741P CIN U27100GJ1976FLC013787 Request for Quotation Number 6000126470 Date 30.12.2024 Submission Date 09.01.2025 Coll Req No AMNS deals with OEMs directly. We are very well equipped in every way to import / buy our goods directly from OEMs from any part of the world in a professional manner. We also use the vast global networks of our parent companies where necessary. We do not welcome any contact from intermediaries or Indian Agents of vendors. We assure all OEMs that you do not need to engage anyone to manage your transactions with us.Kindly respond to our RFQs and deal with our officials directly without involving any agents or intermediaries. Offers of vendors who insist on involving intermediaries in dealings with us could be disqualified. Contact for this RFQ null Sravan Lanka Contact Email sravan.lanka@ext.amns.in MATERIALS / SERVICES Please acknowledge receipt of the RFQ And provide your best quote for below given RFQ details. SR. No PR No. PR Item RFQ Item Services for line Item Quantity UOM Technical Details Other Details § Frequently check whether the cord is parallel to the centre line and if necessary, take corrective action. § Strictly follow the standard cord staggering pattern. § After staggering build the edges of splice. § Fill the gaps properly with inter cord strips. § Apply a thin coat of solution over the splice. § Lay special bonding strip along the beveled edges of belts and roll it properly. § Lay uncured top rubber over the splice location. Care should be taken to keep the tie gum layer in bottom. § Mark and cut it to correct size and fix it. § Hammer slightly along bias line joints. § Check the bias joint lines between the mother belt and filled if there is gap. § Roll with plain roller from centre to edges of the splice and remove the entrapped air. § Lay silicon paper over bias joint lines on both sides. § Place suitable fabric cloth over splice location. § Place edge bars on both edges and arrest it properly using clamps. § Arrange top platen, hydraulic beams suitably and bolt it using end bolts. Vulcanizing: • Curing temperature and time as recommended by the splicing kit manufacturer. • Specific pressure on belt surface for o Light duty 10 to 11 Kg. / cm² o Medium duty 12 Kg / cm² o Heavy duty 13 to 14 Kg / cm² • Pressure to be increased gradually in stages • Final Pressure at 145°C • Cooling up to 70°C with the full pressure • Removal of vulcanizing machine Inspection of Joint: • -Excess rubber on the edges to be trimmed • -Excess rubber on the bias line to be trimmed and buffed smoothly • -Check the hardness at the joint (splice) area. • -Check the thickness of belt and joint. • -Check the width of belts and joint. • -Record the observations. j. Conveyor Belt Joining checklist. The vulcanizing belt joint checklist is to be filled at the time of vulcanizing procedure and same is to be submitted at the time of service record for the billing period. k. Penalty Clause: For any Joint or lagging failures with respect to poor workmanship and quality of the materials provided for services for the jobs executed upon investigation by the Engineer In charge, the contractor is liable for the below deduction as mentioned in the table below. S.no Type of Failure Usage/Location Unit Deduction 01 Conveyor Pulley Laggings Critical/Hot Line 1. G7 Series 2. G8 Series 3. Product Conveyors 4. Stacker Yard Conveyor 5. G1 Series. 6. G3 Series 1 Number Pulley 2.0 Times the value of the Job. + The contractor shall bare and execute the repair or replacement activity. No Charges shall be paid for the repair activity. 02 Conveyor Pulley Laggings Semi Critical 1. B4 and Series. 2. G2 Series 3. Shipment Series. 4. Raw Material Handling 1 Number Pulley 1.5 Times the Value of Job+ The contractor shall bare and execute the repair or replacement activity. No Charges shall be paid for the repair activity. Page 8 of 8 ArcelorMittal Nippon Steel India Limited AM/NS PELLETS VIZAG Near Flyover, Scindia Road,Visakhapatnam,530004,Andhra Pradesh,India GSTIN 37AAACE1741P1ZG PAN AAACE1741P CIN U27100GJ1976FLC013787 Request for Quotation Number 6000126470 Date 30.12.2024 Submission Date 09.01.2025 Coll Req No AMNS deals with OEMs directly. We are very well equipped in every way to import / buy our goods directly from OEMs from any part of the world in a professional manner. We also use the vast global networks of our parent companies where necessary. We do not welcome any contact from intermediaries or Indian Agents of vendors. We assure all OEMs that you do not need to engage anyone to manage your transactions with us.Kindly respond to our RFQs and deal with our officials directly without involving any agents or intermediaries. Offers of vendors who insist on involving intermediaries in dealings with us could be disqualified. Contact for this RFQ null Sravan Lanka Contact Email sravan.lanka@ext.amns.in MATERIALS / SERVICES Please acknowledge receipt of the RFQ And provide your best quote for below given RFQ details. SR. No PR No. PR Item RFQ Item Services for line Item Quantity UOM Technical Details Other Details 03 Conveyor Belt Joining Critical/Semi Critical 1. G7 Series 2. G8 Series 3. Product Conveyors 4. Stacker Yard Conveyor 5. G1 Series. 6. G3 Series 7. B4, G2 8. Shipment Series 9. Raw Material Conveyor 1 no’s Joint a. 1.5 times the Value of Job for Cold Vulcanizing Joints+ Note Below* b. For Hot Joints 2.0 Times the Value of Job+ Note Below* ‘*- The contractor shall bare and execute the repair or replacement activity. No Charges shall be paid for the repair activity. 1. In case of failure of the contractor to complete the job assigned to him within the completion time specified for the job, Engineer-in-Charge may allow reasonable extension for completion period, but penalty due to Failure shall be leviable as per the deduction mentioned in the table above for a particular bill cycle. 2. At the time of bill submission, the contractor shall clearly mention the total job value incurred with any deduction if any in the Invoice along with the necessary back up for the invoice submitted in the billing cycle.
