Bids Are Invited For Furniture Requirement Executive Computer 1200 Mm X 610 Mm 5 The Table Panels Are Made From 18 ±0.5Mm Thk Pre-Laminatedexterior Grade Plt ( Grade I,Typeii )(Is 12823) With Pvc Edgebanding On All Sides. Drawer Bottom Panels Are Made , Kamrup-Assam

Bids Are Invited For Furniture Requirement Executive Computer 1200 mm x 610 mm 5 The Table Panels are made from 18 ±0.5mm thk Pre-LaminatedExterior grade PLT ( Grade I,TypeII )(IS 12823) with PVC edgebanding on all sides. Drawer bottom panels are made up of 9mm thick (±1mm)Pre-laminated Particle Board. Locking has been provided on top drawer only. Table has provision of CPU monitor, Drawer and Sliding KBPT.The Table has a knock-down construction. OEM SHould be a valid member of BIFMA and should have aleast 18 products in BIFMA Compliance Registry 2 Computer Chair Mid Back 5 Seat assembly should be made up of 1.2 cm thick hot pressed plywood measured as per QA method described in OCP-QLTA-P14 18, upholstered with fabric upholstery covers and moulded poluyrethene foam. Seat size should be 47cm W*48 cm D. Back assembly should be made of powder coated tubular frame of 1.54cm * 0.2 cm thick. MS SRW tube designed with contoured lumbar support for extra comfort. the Back is upholstered using net fabric with high lenecity yarn. High back size should be 46.5cm W* 70.5cm H. The High Resilience Polyurethene foam should be moulded with density 45 kg/m3 and hardness load 16 kgf for 25% compression. Armrests should be one piece and should be injection moulded from black co polymer polypropylene. CEntral tilt mechanism should be designed with features like - 360 degree revolving type, 17 degree maximum tilt on pivot at centre, upright position locking and tilt tension adjustment. The pneumatic height adjustment should have an adjustment stroke of 11 cm. The below should be 3 piece telescopic type and injection moulded in black polypropylene. Pedestal assembly should be injection moulded in black 33% glass filled Nylon66 and filled with 5 no.s twin wheel castors. the pedestal is 66.3 cm pitch center dia. 76.3 cm with castors. The twin wheeled castors should be injection moulded in black lylon. Product should be GRIHA, SVA GRIHA, IAQ GOLD, Green Pro, Certified. OEM SHould be a valid member of BIFMA and should have aleast 18 products in BIFMA Compliance Registry 3 Big Steel shelving cabinets Big size almirahof 916mm W x 486mm D x 1981mm H made of 0.7mm thick CRCA MS epoxy powder coated with welded construction. The almirah should have 4 adjustable shalves made with 0.8mm thick CRCA MS. The doors should be metal door made with0.8mm thick CRCA MS having mozac handles with m10 screw type leaver. Product Should be Green Guard(UL) UL, Green pro, GRIHA, IAQ GOLD Certified. OEM should have a valid BIFMa membership with at least 10 products in BIFMA compliance registry. OEM should be Greenguard certified and should have 10 products in UL greenguard registry. OEM SHould be a valid member of BIFMA and should have aleast 18 products in BIFMA Compliance Registry 4 File Cabinet 4 drawer vertical filing 2 It should have rigid knock down construction made of CRCA. Panel Thicknes: Top side and drawer front 0.7mm. Frames, Drawer- inside cover,side back side 0.6mm.back,bottom and drawer bottom-0.5mm.The drawer front should have easy to grip full length handle recess integrated into metal drawer fronts. The filing cabinet should also have sanp on type label holder on drawer front. It should have centralized locking with 10 lever cam lock and have anti tipping arrangment to ensure that when one drawer is opened for use, it doesnt allow other drawers to be opened. The drawers should be mounted on high quality precision ball slides. The uniformly distributed load capacity of drawers should be 40 kg for 75000 cycles. It should have plain triangular plate pop riveted at bottom corner for rigidity. Accesories like drawer partition and cradle for hanging A4 files front to back should be there. Epoxy powder coated finish of thickness 50 microns (+/-10 ). Dimension: 1320mmhx470mmDx620mmD. Product Should be certified with IAQ GOLD. OEM should have a valid BIFMa membership with at least 10 products in BIFMA compliance registry. OEM should be Greenguard certified and should have 10 products in UL greenguard registry. OEM SHould be a valid member of BIFMA and should have aleast 18 products in BIFMA Compliance Registry 5 Revolving Chair with Active B-Synchro mechanism High Back The cushioned seat should be made of injection moulded Plastic outer & inner. Plastic inner should be upholstered with leatherette and moulded High resilience polyurethane foam of density 45+/-2 kg/m3, and hardness load 16+/-2 kgf as per IS :7888 for 25% compression.The cushioned back is made of PU foam with insitu molded MS ERW Round tube of size 1.9+/- 0.03cm x 0.16+/-0.0128 cm.It should be upholstered with leatherite. Seat size :47 cm (W) x 48 cm (D). High back size :47.7cm (W) x 76.4 cm (D). Mid back size : 47.7 cm (W) x 60.1cm (D). The product should have Green Guard(UL) Gold, BIFMA Level 2, IAQ Gold, Green Pro & GRIHA certifications. OEM SHould be a valid member of BIFMA and should have aleast 18 products in BIFMA Compliance Registry 6 Executive Officers Table with one side E.R.U. unit with Pedestal with ERU 2 The Table set should have Main Table + Side Table + Mobile Pedestal Unit . i) Main Table should be made of 25mm PPB with postformed finish. The size should be 1800mm W x 900mm D x 740mm H. The Modesty is 18mm thk PPB clad with 0.1 thk Decorative Laminate of both sides. ii) The Side Table should be made of 25mm PPB with postformed finish. The size should be 1550W x 450D x 705H. The modesty is 18mm thk PPB clad with 0.1 thk Decorative Laminate of both sides. iii) The mobile pedestal should be made of CRCA Steel with epoxy powder coated. The pedestal should have three drawers.OEM SHould be a valid member of BIFMA and should have aleast 18 products in BIFMA Compliance Registry 7 Credenza HDU 4315 1 25 MM THICK PLAIN PARTICLE BOARD (PPB) CLAD WITH 0.6MM THICK POST FORMED LAMINATE AND 1MM THICK BACKING LAMINATE (BDL). FLAT EDGE DULY SEALED WITH 2MM THICK PVC BEADING. 18MM THICK PLAIN PARTICLE BOARD (PPB) CLAD WITH 1.0MM THICK DECORATIVE LAMINATE (DL) ON BOTH SIDES. EDGE SEALED WITH 2MM THICK PVC BEADING. OEM SHould be a valid member of BIFMA and should have aleast 18 products in BIFMA Compliance Registry 8 Mesh visitors Chair Seat assembly should be made up of 1.2 cm thick hot pressed plywood measured as per QA method described in OCP-QLTA-P14 18, upholstered with fabric upholstery covers and moulded poluyrethene foam. Seat size should be 47cm W*48 cm D. Back assembly should be made of powder coated tubular frame of 1.54cm * 0.2 cm thick. MS SRW tube designed with contoured lumbar support for extra comfort. the Back is upholstered using net fabric with high lenecity yarn. High back size should be 46.5cm W* 60.5cm H. The High Resilience Polyurethene foam should be moulded with density 45 kg/m3 and hardness load 16 kgf for 25% compression. Armrests should be one piece and should be injection moulded from black co polymer polypropylene.The Tubular frame should be powder coated of cantilever type and made of 2.54cm*0.2cm thick MS ERW Tube. Product Should be IAQ Gold, Green Pro Certitfed. OEM SHould be a valid member of BIFMA and should have aleast 18 products in BIFMA Compliance Registry Total Quantity : 24

Refer document

Refer document

Refer document