Road Signage And Road Furniture Work On Firozabad Jalesar Road Odr In Fy Fy 2024-25 - Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface. Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35-2015 The finished surface to be level, uniform and free from streaks and holes. SOR CH-27 Item No-2 But GST Excludcing 2 6M Span overhead Cantilever Structure with 300dia MS one vertical post Supply, fixing & erection of built up Cantilever Structure 6 m span comprising of one vertical posts of 6.00 M height made up of 300 mm NB heavy class MS pipe as vertical member welded with 10 mm MS plate at top & 12 mm M S plate at bottom. The horizontal Truss shall comprise of 50 mm dia heavy class M. S. pipe and 40 mm dia heavy M S pipe as bracing & 10 mm M$ plate at bottom for fixing to vertical post as per structure design & drawing with one of steel primer and two coats of synthetic enamel plant. The work includes construction of RCC Foundation of size 0.90×0.90×1.50 m of required depth as per site condition for built up structure including Earth work in excavation 100 mm thick Lean Concrete in 1:3:6 cement coarse sand and 40 mm gauge stone ballast and RCC - M25 grade concrete including supply and fixing of 25 mm dia Foundation Bolts 600 mm long as per provision of structure design including cost of reinforcement & shuttering. The lateral vertical clearances and complete installation work shall be as per relevant clauses of MORT&H specification section 800 and IRC 67: 2012 complete in all respect The Rates shall include cost of design fabrication, supply, transportation Local shifting Erection of Signage structure using crane, inclusive of all taxes etc. all T&P machine, material and labour required for proper completion of work as per direction of Engineer-in-charge.SOR CH-27 Item-4 But GST Excludcing 3 Retro-Reflective Sheeting type-XI with 4 mm thick ACM Double Side :Providing & fixing of reflective signs with a corrosion resistant 4 mm thick with 0.4 to 0.5 mm both side aluminium skin aluminium composite panel face to be fully covered with High Intensity prismatic sheeting type IV as per IRC-67:2012 retro reflective sheeting with back frame MS angle of 35x35x5 mm. Legends, letters, numerals and borders etc should be as per MORTH specification No-801.3.7 .The sheeting shall have a pressure - sensitive adhesive of the aggressive - lack type requiring no heat, solvent other preparation for adhesion to a smooth clean surface, in a manner recommended by the sheeting manufacturer. The ACM (Aluminium Composite Materials) shall be fixed on the Back frame MS Angle with riveting. Micro prismatic type IV Retro reflective sheeting confirming to ASTM D4956-09 shall be Pressure fixed. The Retro reflective sheeting shall be lested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from international/Goverment Laboratory Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D 4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer/Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67:2012 & Proof of the same Report shall be uploaded which quoting tender. The rate shall include all materials, labour, T&P, transportation, installation and incidentals all complete as per direction of the Engineer-in-Charge. SOR CH-27 Item No-13 But GST Excludcing 4 Retro-reflectorised Traffic sign as per IRC-67-2012 providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC :67-2012 made of high intensity grade sheeting type-IV vide clause 801.3, fixed over aluminium sheeting 1.5 mm thick supported on a mild steel angle iron post 75 mm×75 mm×6 mm firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete 45 cm×45 cm×60 cm. 60 cm below ground level as per approved drawing. The Retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International/Government Laboratory Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D 4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer/Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67.2012. Legends, letters, numerals and borders etc should be as per MORTH specification No-801.3.7. Proof of the same in form of government report shall be uploaded while quoting tenderi) 60cm equiliteral tringle with diffinitation plate size (20cmX60cm) SOR CH-27 Item No-18-(II) But GST Excludcing 5 ii) 60cm Circular with diffinitation plate (20cmx60cm) SOR CH-27 Item No-18-(III) But GST Excludcing 6 iii) 80mmx60mm rectangular with diffinitation Plate (20cmx60cm) Informetory Board SOR CH-27 Item No-18-(IV) But GST Excludcing 7 iv) 60mmx45mm rectangular with diffinitation Plate (20cmx60cm) SOR CH-27 Item No-18-(V) But GST Excludcing 8 V) 90 cm high octagon SOR CH-27 Item No-18-(VII) But GST Excludcing 9 vi) 30x90 cm Left & Right Hazard Object SOR CH-27 Item No-18-(X) But GST Excludcing 10 Linear Delineator System (LDS) Supply & fixing of Linear Delineator System (LDS) panels made of Micro Prismatic Retro Reflective sheeting type XI duly laminated on thin aluminum foil to a unique corrugated shape to provide Retro Reflection across wide range of observations and external angles. Eatch LDS panel should be of nominal length of 33 inch and each ridge shall be approximately 0.34 inch high. Each LDS panel is to be firmly fixed on existing concrete/brick work with 16 Nos fastener/screw. SOR CH-27 Item No-9 But GST Excludcing 11 Making speed table bitumenous concrete with 5.4% VG-30 material (Tropizoidal Speed Table) on SHR/MDR/ODR Road with B.C. in tropizoidal shape 100mm high complete in all respect As per morth & specification and as per direction of E/I. As per Estimate But GST Excludcing 12 Making hump on village roads junction with Bitumenous Concrete material with 5.4% VG-30 bitumen in circular shape, 1.00m wide and 0.075m height complete in all respect as per MORT&H Specification and as per direction of E/I.As per Estimate But GST Excludcing
