Tender For Renovation Of C.R. building., Raising Of B.Wall, App.Road, Augumentation Of Yard, Toilet Block And Other Alied Civil Works At 33/11 Kv S/S Bansthali And Jodhpuriya., 1 Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared. (B-1.31) 2 Earth work in excavation by mechanical means (Hydraulic Excavator )/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including taking out the excavated soil and depositing and refilling of jhiri with watering & ramming and disposal of surplus excavated soil as directed with in a lead of 50 meter. All kinds of soils(B-1.8) 3 P & L in position cement concrete including curing, compaction etc. complete in specified grade excluding the cost of centering and shuttering -All work up to plinth level. (A) 1:4:8 ( 1 cement : 4 coarse sand: 8 graded stone aggregate 40mm nominal size.) (B/3.1.6) 4 (B) M20 grade Nominal Mix1: 1.5: 3 (1 cement : 1.5 coarse sand : 3 graded stoneaggregate 20mm nominal size).(B/3.1.1) 5 RR stone masonry for with hard stone in foundation and plinth in CSM above 30cm thick wall in CM 1:6 (1cement :6 Sand). (B/6.1.6) 6 Brick masonry with F.P.S. bricks of class designation 75 infoundation and plinth with bricks .Cement mortar 1 : 6 (1 cement : 6 coarse sand)(B-5.1.2) 7 P & L in position specifed grade of cement concrete for all RCC structural elements upto plinth level including curing, compaction, finishing with rendering in cement sand mortar 1: 3 (1cement : 3 coarse sand) and making good the joints & cost of plastizers (if required) excluding the cost of centering, shuttering and reinforcement. M20 grade Nominal Mix /Design Mix.(B-4.1) 8 Renewing glass panes, with putty and nails wherever necessary. Float glass panes of thickness 4 mm (B- 13.4.1) 9 S & F stone lintels / bed plates of approvedquarry rough dressed in cement mortar 1:4 : Up to 15 cm thick. (B-6.18.1) 10 P & L in position specified grade of CC for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1: 3 (1cement :3 coarse sand) and making good the joints & cost of plastizers (if required) excluding the cost of centering, shuttering and reinforcement for Beams, suspended floors, roofs, griders having slopes up to 15̊ landings, balconies, shelves, chjjas, lintels, bands, plain windows sills, staircases and spiral staircases. M20 grade Nominal Mix / Design Mix. (B-4.3) 11 C & S with plywood or steel sheets including strutting, propping bracing both ways with wooden members and removal of formwork for superstructure up to floors, roofs, landings staircases, balconies, girders, cantilevers, bands, coping bed plates, anchor blocks, sills, chhajjas, lintl, beam etc.(B-4.10.2) 12 P & F reinforcement for R.C.C. work including straightening, cutting, banding, placing in position and binding (including cost of binding wire) all complete up to floor five level. Hot rolled deformed bars (IS:1139). (B-4.13.2) 13 Halfbrick masonry in superstructure, above plinth level upto floor V level using bricks of designation 75. Cement mortar 1:6 (1cement: 6 coarse sand). (B-5.8.3) 14 Brick work with F.P.S. bricks of class designation 75 in superstructure above plinth level upto floor V level in all shapes and sizes in :: Cement mortar 1 : 6 (1 cement : 6 coarse sand)(B-5.2.2) 15 Grading for roof water proofing treatment with CementConcrete1:2 :4(1cement:2coarsesand:4gradedstoneaggregate20mmnominalsize) with water proof compound as per manufactures specification. (B-10/10.17.1) 16 P & F precast cement concrete coping 1:2:4 mix 50 mm thick copmlete as per specification : (B-3.8) 17 Providing Gola 75×75 mm in cement concrete 1:2:4(1Cement:2coarse sand: 4 stone aggregate 10mm and down gauge) including finishing with cement morter 1:3 as per standard design.(B-10/10.22) 18 P & Fsteel glazed doors windows andventilator shutters of standerdrollde steel section joints mitred andwelded with steel lugs 13x3mm, 10 cm, long embeded in cement concrete block 15X10X10CM of 1:3:6 (1 cement : 3 coarse sand:6 gradedstoneaggregate20mm nominal size) of with wooden plugs and screws of rawl plugs and screws with fixing clips or with bolts and nyts as required includingprovidingand fixing of plain glass panes 4mm thickwith cooper glazing clips and special metal sash puttyof approvedmake of metal beading with screws complete including priming coat of approval steel primer, excluding the cost of metal beading and other fitting except necessary hinges of pivots steel handlwds peg stay etc. as required:(A) Window side hung /Ventilators top or centre hung (openable) (B-9.19.3) 19 Supplying and fixing fixed wire gauge of 14 mesh x 24 gauge to the metal frame of rolled section by metal beading 20×3mm with suitable screw at not exceeding 150 mm distance.(B-9.26) 20 Providing and fixing square bars or other flat welded to windows, ventilators etc. (B-9.27) 21 RR dry stone kharanja under floor. (B-11.26) 22 P & F T-iron frames for doors, windows & ventilators of mild steel Tee- section, joints mitred & welded with 15 X 3 mm lugs 10cm long embeded in CC blocks 15X10X10 cm of 1:3:6 (1cement :3 coarse sand: graded stone aggregate 20mm nominal size) or with woodenpluges & scews of plugs & scews or with fixing clips or with bolts & nuts as require including fixing of necessary butt hinges & screws & applying a priming coat of approved steel primer. (B-9.5) 23 S & F in walls machine cut and polished stone shelves,tands and in 1:3 with machine cut edges: (A) Kota stone minimum 30 mm thick (B-6.17.3) 24 Providing and fixing external grade board solid core single leaf flush door shutters ISI 2202-67 market using phenol formal dehysresin in glue both side with approved steel bildding complete as pr annexure A,30 mm thick commercial vernier both side. (B-8.13.2.1) 25 P & F M.S. Sheet 1mm thick single leaf door shutter in angle iron frame 35 x35x5 mm suitablly diagonally braced with 25 x 3 mm flat iron above & below lock rail of size 50x5 mm beading extra including all fittings, as per direction of Engg. Incharge but excluding cost of chowkhats: including two coat of anti-corrosive red oxide primer paint. (B-9.17) 26 Add Extra for Double leaf door shutter (B-9.17.1) 27 Plaster on new surface on walls in cement sand mortar 1:6 including racking of joints etc. complete fine finished. (A) 20mm thick. (B-12.3.2) 28 (B) 12 mm thick. (B-12.3.3) 29 6mm cement plaster to ceiling of mix 1:3 (1cement:3 fine sand).(B-12.5) 30 P &F 1st quality standard white, grey, ivory, fume red brown, light green, light blue and other light shadesglazed tiles conforming to IS: 13753 & IS:15622 of size 200mm x 300 mm in walls, floors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls & pillars). (B-7.12) 31 P & L 1st quality MAT finished ceremic tile size 300 x 300 mm confirming to IS: 13755 and IS:15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars etc. laid a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement mortar bed).(B-7.13) 32 Kota stone slab flooring 25 mm thick over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of cement mortar 1: 4 (1 cement : 4 coarse sand) (A) For area of each slab upto 2001 to 5000 Sq.Cm. (B-11.18.2) 33 Kota stone slabs 25mm thick in riser of steps, Skirting, dado and pillars laid on 12mm (Average) thick cement mortar 1:3 (1cement:3coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete: for area of each slab from 2001 to 5000 Sq.Cm. (B-11.19.2) 34 Providing and fixing of double leaf steel shutter for cupboard, the frame is made of pressed steel ISI section 80x25 mmx1.25 mm thick with 1.00 mm MS sheet to spot welded including holdfasts of 15x3mm, MS oxidized fittings such as butt hinges, sliding doors bolts, handles, tower bolts and twin peg etc complete including applying priming coat of approved steel primer of red oxide zinc chromate and spray painting in approved shade with deco paint of approved quality complete as per direction of Engineer In Charge. (B-9.39) 35 Structural steel work riveted,bolted or welded in built up sections, trusses and framed work, including cutting, hoisting (height upto 10 m) , fixing in position and applying a priming coat of approved steel primer all complete:(B-9.2) 36 Add extra for square or Rectangular Pillars in S/S brick work upto five storey. Upto 45 cm length and two corners are free (B-5.3.2) 37 Providing and fixing welded mesh/expanded metal mesh in frame work, flat iron beading 20x3mm including top cross laps inside and out sides welding, iron bolts, crews, clips etc. complete (excluding frame work) of size. Welded mesh 25 mmx 25 mm x 2.1 mm.(B-9.38.3) 38 Providing and fixing cow catcher made of R.S. joist angles channels MS rounds including cutting welding and fabrication with priming coat of red oxide (as per design). (B-9.7) 39 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement in position to the required line, level and curvature jointed with cement mortar 1:3 (1 cement :3 coarse sand ) including making joints with without grooves (thickness of joints except at sharp curve shall not to more than 5mm) including making drainage opening wherever required complete including painting etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer in- charge). (B-11.29) 40 Finishing walls with acrylic smooth exterior paint of required shade including all scaffolding. New work (two or more coats applied @ 1.67 ltr/10sqm over & including base coat of water proofing cement paint applied @ 2.20 Kg/10sqm). (B-12.42) 41 Applying priming coat:With ready mix pink or gray primer of approved brand and manufacture on wood work hard and soft wood. (B-12.45.1) 42 Painting with synthetic enamel paint of approved brand and manufacture to give and even shade : (A) Two or more coats on new work. (B-12.46.1) 43 (B) One or more coats on Old work. (B-12.46.1) 44 Providing and applying white cement based puttyover plastered surface to prepare the surface even and smooth complete. New Plastered Surface. (three or more coats) (B-12.22.1). 45 Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade including all scaffolding: (A) Newwork(twoormorecoats) over and including scrapping and priming coat with cement primer. (B-12.37.1) 46 Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Sills Counters, Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement : 3 coarse sand) jointing with white cement mortar 1:2 (1white cement : 2 marble dust) with pigment to match the shade of the marble slab including grinding, rubbing and polishing complete. Rajasthan Black.Above 3601 Cm2 Slabs (B-7.5.6) 47 Extra for providing edge moulding to 15-18mm thick marble/ Granite stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite / Kota Stone work Full Edge moulding.(B-7.6.2 (i)) 48 Making of drip course (Tapka) in cement sand mortar 1:6 width upto 40 mm and 10 mm thick as per approved design. (B-12.20) 49 Making grooves as per design in plaster 10mm to 20mm wide. (B-12.19) 50 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, making of lines or groove etc complete but excluding the cost of nosing of steps etc. complete. 75 mm thick with 20mm thick nominal size aggregate. (B-11.3.2) 51 Cleaning of sewer line of various sizes as per requirement at site of different sizes including 100mm,150mm & 225mm dia ofStoneware pipe as per direction of Engineer-in-Charge..(S-3.48) 52 Providing and fixing steel gate, grating , and grills made of angles, tees, square bars, flats,or black pipe with holdfast and fittings complete as per design and drawing including cutting welding and fabrication with priming coat of red oxide.Extra if square,rectangular hollow tubelar sections are used or grill made by flats only. (B-9.8+9.8.1) 53 Providing and laying ofpaver block as per IS 15658 : 2006 (Indian standard for precast concrete block for paving- specification) and IRC : SP:63-2004 (guidelines for the use of interlocking concrete block pavement)M-40,80mm thick to be used in medium- traffic ( Medium traffic is defined as a daily traffic of 150-450 commercial vehicles exceeding 30 KN laden weight, or an equivalent of 0.5 to 2.0 MSA for a design life of 20 years.) like city streets, small and medium market roads, low volume roads, utility cuts on arterial roads, etc. Category A Denated units to key into each other on four faces zigzagshape as per IRC SP 63:2004Add extra over item No. 11.38, A to C if reflective paver block, manufactured with wet cast vibration system in two layers is used.(B-11.38.3.(A)+11.39) 54 P&F Indian type white glazed vitreous china 1st quality W.C. orissa pan (IS : 2556 Mark) with 100 mm vitreous china P or S trap including cutting and making good the wall and floor.Size 580x440 mm.(S-1.2.2) 55 P&F WVC wash basin (Ist quality IS: 2556 mark) of approved make with C.I. brackets duly painted, 1 No.15mm C.P. Pillar cock (IS: 8934 mark) & 32mm C.P. brass waste coupling of approved make, 25mm G.I. waste pipe complete including cutting and making good the walls,580mm X 450mm. (S-1.36.4) 56 P&F Towel rail or Ring of approved quality/make C.P.brass towel rail with brackets 450x20mm. (S-1.47.3) 57 P&F PVC storage tank (IS: 12701 marked including the BIS license No.) of approved make with cover,25 mm dia IM long over flowing & 25 cm. Long wash out pipe with plug & socket, including making connection etc. Complete of approved deisgn : 500 liters capacity. (S-2.26.3) 58 P&F Looking Mirrors with P.V.C. frame of approved (atul/Modi guard.Sanit Gobin or equivalent) size 500x400mm. (S-1/1.45.1) 59 P & F Chlorinated Polyvinyl Chloride (CPVC) pipe, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fitting i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement & testing of joints complete as per direction of Engineer in Charge. ( Internal work Exposed on wall). (A) 15mm nominal outer dia pipes. (S-2.37.1) 60 (B) 25mm nominal outer dia pipes. (S-2.37.3) 61 P & F Chlorinated Polyvinyl Chloride (CPVC) pipe, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings, this included jointing of pipes & fittings with one step CPVC solvent cement, trenching refilling & testing of joints complete as per direction of Engineer in Charge. ( External work). (A) 15mm nominal outer dia pipes. (S-2.39.1) 62 (B) 25mm nominal outer dia pipes. (S-2.39.3) 63 Making connection of GI distribution branch with GI main including all fitting : Upto 25mm dia.(S-2/2.3.1) 64 P&F bib cock (IS : 8931 mark), Superior quality of approved make.(A) CP Brass bib cock 15mm nominal bore. (S-2.7.3) 65 P&F ball cock (IS : 1703 mark) with rod& PVC ball complete: Brass wt. Not less than 300gm 15mm. (S-2.11.1) 66 P & F Full way valve (IS : 778 Mark) or wheel valve of approved make. (A) Gun-metal 15mm nominal bore. (S/2.15.1) 67 (B) Gun-metal 25mm nominal bore. (S/2.15.3) 68 P & F Flush Cock / Flush Valve (IS : 9758 Mark) for WC of approved quality make :Brass / Gun metal Half-turn wt. 1 Kg. of approved quality / make, 25mm nominal bore. (S-2.14.9) 69 P&F inlet connection (Angle velves) superior quility of approved make for washbasin Gyser etc. CP intel connection 15 mm Brass (IS: 8931 marked). (S-2.12.1) 70 P & F 15 mm. Dia Connection Pipe of approved quality/make :PVC pipe withC.P. Brass nuts upto length, 300mm. (S-2.13.1) 71 Construction of manhole in all typeof soil inner size 90X 60 Cm. 300 mm thick masonry in CM 1:6, 10 Cm thick CC 1:5:10 in foundation, 20 mm thick inside plaster in CM 1:6, finished with floating neat cement, 50 mm thick M -15 grade C.C fooring, making, channels, 80mm thick stone slab covering with 40mm thick M- 15 grade C.C flooring, Cement cocer with frame of 450mm dia, earthork etc. as per design including disposal of surplus earth within 50 mtr. lead. Depth up to 0.5 m.(S-3.19.1) 72 Construction of soakage well in all type of soil with 300 mm thick dry masonry, top and bottom 300mm course in CM 1:6, 80mm thick stone slab, jointing of slab in CM 1:3 Ralthal, kharanja, 40. mm thick M-15 grade C.C. flooring, earthwork complete as per approved drawing including disposal of earth within a lead of 50 mtr. Size 240 cm . dia outside & 240 Cm. depth.(S-3.22.3) 73 Construction of septic Tank in all types of soil with 40 Cm .thick masonry in CM 1:6, 15 Cm thick C.C bed of 1:5:10, M- 15 grade C.C floor & RCC slab covering with M15 grade c.c. floor, 50 mm thick stone slab partition walls, 20 mm thick plaster in CM 1:6 finished with neat floating cement, 4 Nos stone foot rests of approved design ,two No. 450 mm dia each Ferro cement cover with frame, earth work etc. complete as per approved drawing including disposal of surplus earth within a lead of 50 mtr:-. size 200×100×130 cm. (for 10 users.) with 115 mm thick RCC (M-20) slab with Tor steel reinforcement 8mm ϕ @15 cm c/c bothways including shuttering complete in all respect.(S-3.27.1) 74 Providing and laying cement concrete 1:5:10( stone aggregate 40mm nominal size) upto haunches of S.W. pipes including 150mm thick bed concrete ( Width W= Dia of pipe in Cm + 30Cm.) conrete width to be reduced from width W at centre of pipe to 0 at top of pipe(Excluding cost of pipe).100 mm diameter S.W. Pipe.(S-3.3.1) 75 Construction of chamberin all typeof soli with300 mm. thick masonry in CM 1:6 m 10Cmthick C.C1:5:10 infoundation, 20mm thick inside plaster in CM 1:6, finshed with floatinf neat cenent50 mm thickM-15 grade C.C flooring, Ferro work etc. complete as perdesing includingdisposal of surplus earth within a lead of50 mtr. Inside size 300 X 300 mm depth upto 0.5 M Cement cover with frame.(S-3.21.1) 76 P&F rigid PVC pipe (IS:4985 mark) class-II (4kg/Cm2approved quality/ make including jointing the pipe with solvent cement rubber ring and lubricant (A) 75 mm dia (S-3.16.2) 77 (B) 110mm dia (S-3.16.3) 78 P&F rigid PVC pipe (IS:4985 mark) of appoved quality/ make incliding joint the pipe with solvent cement rubber ring and lubricant : 110 mm dia.(A) Bend 45°(S-3.17.8 ii) 79 (B) Bend 87.5°(S-3.17.9 ii) 80 (C) Vent Cowel. (S-3.17.12. ii) 81 (D) Pipe Clip.(S-3.17.15.ii) 82 Supply & fixing G.I. Union ISI marked in G.I. pipe line as required complete in all respect of size :(A) 15mm dia nominal bore (S-2.32.1) 83 (B) 25mm dia nominal bore (S-2.32.3) 84 P & F sand cast Floor Trap (Nahni) of (IS : 1729 mark) of approved quality / make with socket down or hinged grating including good the floor.Size 100x100mm. (S-3.12.1) 85 P & F Kitchen & Lab. Sink of approved make with C.I. brackets duly painted, 40 mm C.P. waste coupling, C.P. Brass chain with rubber plug, 40 mm G.I. waste pipe up-to floor level complete including cutting and making good the wall & floor :1.0 mm thick stainless steel AISI -304 & IS 13983-1994 kitchen sink of approved make as per Engineer-in-charge with large waste coupling. Overall size (inches) 24 x 18 x 8Bowl size (inches) 20 x 16 x 8 (S-1.38.9.3) 86 Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694)inrecessed ISI marked MMS ( IS:9537 P - III ) virgin material PVC conduit & itsISI marked (IS:3419-1988) accessories, round tiles, 1.2 mm thickHot Dipped Galvanized Modular Box with earth terminal, 10A Modular switch, Modular face plate with grid plate, 3 pin ceiling rose / Holder /3 way connector, screws,making connections, testing etc. as required.For specification of copperConductor,Phenolic Laminated sheets & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure A attached with this BSR (A) Short point (upto 3 mtr)(E-1.1) 87 (B) Medium point (up to 6 mtr) (E-1.2) 88 (C) Long point (uo to 10mtr) (E-1.3) 89 Wiring of 3/5 pin 6 amp. Light plug point with 1.5 sq. mm nominal sizeFR PVC insulated unsheathed flexible copper conductor 1.1 kV gradeand 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade(IS:694) inrecessed ISI marked MMS ( IS:9537 P - III ) PVC conduit & its ISI marked (IS:3419-1988)accessories, Hot Dipped GalvanizedModular box of 1.2 mm thick with earth terminal, 10 A modularswitch, 3/5 pin 6 A modular socket, Modular face plate with grid plate, screws, making connections, testing etc. as required.For specification of copperConductor,Phenolic Laminated sheets & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07 For additional technical parameters of product / work refer Annexure A attached with this BSR. On Board (E-1.3.1) 90 Providing and fixing of power plug point with non modular accessories as per PWD specification for electrical Works withGalvanized box of 1.2 mm thickwith earth terminal with suitable size phenolic laminated sheet (IS : 2036 -1995) cover including cost of 16 amp. Switch (IS :3854) and 3/6 pin 16 amp. socket outletmaking connection , testing , etc. as required. . For specification ofWiring accessories refer ChapterE - 07 related item &For additional technical parameters of product / work refer Annexure A attached with this BSR(E-7.36) 91 Supplying and drawing FR PVC insulated & unsheathed flexible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from99.90 % purity copper, class 5 stranding in acc. to IS:8130/IEC 60228 forlower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5,in existingsurface or recessed PVC/ MS conduit/casing capping making connections with Copper Lugs of suitable size, Ferrules,testing etc. as required. OEM Must have its own in house NABL lab setup for all testing facilities for wires. For additional technical parameters of product / work refer Annexure A attached with this BSR (A) 2×2.5 sqmm+1x1.5 sq.mm (E-4.1.7) 92 (B) 2×4.0 sqmm+ 1x2.5 sq.mm( E-4.1.14) 93 Supply & Laying following size earth wire in horizontal or vertical run in ground/surface/recess including riveting, soldering, saddles,making connection with GI/Cu purity purity >95%thimble etc. as required.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .8 SWG copper Wire 8 SWG copper Wire(E-14.6.5) 94 Pipe Earthingas per IS:3043- 1987 with 3.0 Mtr. Long, 40 mm dia. B class G.I. Pipe IS: 1239 (Part-1) 2004, Equivalent to BS : 1387 with perforated holes of 12 mm dia ,including all accessories like nut, bolts, reducer, nipple, wire meshed funnel, and Heavy duty weather proof poly-propylene earth pit chamber with lockable Jam free lid suitable for safe working load 5000 Kg or more of size Top Dia. 225 to 260 mm, Bottom Dia 300 to 350 mm. and Height250 to 300 mm. and embodying the pipecomplete with alternate layers salt and coke/ charcoal, testing of earth resistance for value of 5 ohms or lessas required & must record by engineer in charge during site visit and ensure to enter in measurment book.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .(E-14.1) 95 Providing & Fixing of IP20 SMD Mid Power LED batten type integrated light fixture made from Powder coated Extruded aluminiumhousing with in built driver, System lumen efficacy ≥ 110 lm/Watt output, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, CRI >80 , life time of minimum50000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , Maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 & LM80) certificate / Report from OEM shall be submitted.All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR.1170mm (+/-10%) LED batten with min. lumen output 2200 lm (E-17.1.1) 96 Providing & Fixing of Street light bracket made out from following size of B class , Medium class G.I. Pipe confirming to IS : 1239 P - 1 ( 2004 ) with heavy duty pole clamp, Saddles suitable fastners etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR. 32 mm Dia.(E-18.18.3) 97 P & F 1.2mm thickM.S. Recessed fan box, hexagonal/ round of size 130 mm dia, depth 75mm,12 mm dia rod fan hook with 100 mmlength extended on each side . All as per pre approved by Engineer in charge.For additional technical parameters of product / work refer Annexure A attached with this BSR(E-5.9) 98 Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches by sandla/loi. (only for colour changing )..(B-12.35.7) 99 Providing & Fixing of 240/415 V AC MCB with positive isolation of 10 kA breaking capacity (B/ C/D tripping characteristic as per type of load andsite requirement) 4 KV impulse withstand voltage, ISI marked IS 8828(1996) / conforming to IEC 60898-1 2002, IEC 60947-2, low watt losses, trip free mechanisum , energy limiting ofclass 3 as per IEC,minimum phase termination capacity of 35sq.mm. , conductor line load reversibility , IP 20 contact protection and fitted inexisting distribution board/sheets, minimum electrical operation 20,000 upto 20 A rating and 10,000 upto 63 A, 5000 for 80 A & above ratingincluding making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge. For additional technical parameters of product / work refer Annexure A attached with this BSRSingle pole MCB (With B/C curve tripping Characteristics) 6 A to 32 A rating (E-6.1.1.2) 100 Providing & Fixing of 240/415 V isolatorISI marked IS:13947-III/conforming to IEC 60947-3, suitable for AC22A utilization category, 4KV impulse withstand voltage,true contact indication,Red colour dolly / lever shall have single mould covering over all poles for operation , two position din rail mounting,minimum phase termination capacity of 35sq.mm.IP 20 contact protection and fitted in existing distribution board / sheetincluding making connections, testing etc. as required. OEM shall have submitNABL / CPRI / ERDA accrediated lab type test reports& All as per pre approved by Engineer in charge.For additional technical parameters of product / work refer Annexure A attached with this BSR Double pole isolator30 A / 40 A rating(E6.2.1.1) 101 Providing & Fixing of Recessed/surface mounting heavy duty Enclosure made out from Galvanized steel / CRCA sheet not less then 1.2 mm thick conforming to IS-8623-1 & 3 / IEC 61439- 1 & 3. powder painted complete with din rail making internal DB terminations with copper lugs, detachable gland plate, including making connections, testing etc. as required.For additional technical parameters of product / work refer Annexure A attached with this BSRSuitable for Six / Eight module for MCB/ RCCB(E-6.9.2) 102 Providing & Laying P.V.C. / XLPE insulated & P.V.C. sheathed ArrmouredAluminiumcable confirming to IS:1554 P-I / IS :7098 P - I of 1.1 KV withH4- Grade electrolyticaluminium conductor confirming to IS 8130 of purity >99.6 %, round / flat strip armouring of cables, Inner / outer sheath confirming to IS:5831in existing RCC / Hume / Stoneware / PVC pipe/ open duct/cable trench / Cable tray(with cable tie) includingtesting etc. as required of following size. OEM must have its own in house NABL accrediated Laboratory for testing procedure as per IS:10810.For additional technical parameters of product / work refer Annexure A attached with this BSR (A)4.0 Sq. mm X 2 core (E-11.2.1.1) 103 Providing & Fixing of IK08, IP 66 protected LED Street Light Luminaire on existing bracket/pole. Fixture made of powder coated single piece pressure die cast aluminummaterial with heat dissipation fins on housing with UV stabilized PC (UV stablization report submitted for UV cover ) /Toughened Glass coverand secondary lens on each LED & should be SMD type of 3 to 5 watt each . The System efficacy >=125 lm/ wt and potted driver& has a unique BIS R number withInput Voltage AC 120 to 270 V AC with High voltage Cutoff @>=300 V AC and Auto resetting Safety , Power Factor >0.95 driverEfficiency >85%,THD(I) <10%Humidity 10% to 90% RH Working Temp -5C to 45C .driver current <750mA. The luminaireshall be BIS certified and Trade mark certified. Life ExpectancyEqual or more than 50000 burning hrs with Minimum 0% lumen maintened , CRI >70 and CCT 5700K +355K. Surgeprotection shall be min ≥ 4 KV internal and min 10 KV external inside driver compartment. driver should be Phase to phase protection of 440 V for 4 Hrs.Manufactures Word Mark/ Name engraved/Embossing on die cast housing to allow traceability/ authenticity. Fixture shall be AS PER IS 10322 Complianced.OEM Must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) Certificate/ report with liable warranty of product/ accessories from OEM shall be submitted. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer. Annexure A attached with this BSR. (A) LED Street Light fixture with Minimum lumen output 3700 lm(E-18.12.2) 104 Supply & Fixing of CO2 type Fire Extinguisher conforming to IS:15683:2018, charged with CO2 gas (purity 99.7% conforming to IS 15222), Powder coated Internal & External Surface Manganese steel ISI marked as per IS 7285 cylinder body , Wheel type Forged brass release valve ISI Marked as per IS 3224 with Inbuilt safety release device ((Fusible plug and Rupture Disc Type), 1.0 Mtr. Metal wire braided hose having minimum bursting pressure of 140 Kgf/cm2, Horn with metallic thread connection, QR code for Product Traceability,including Fixing on wall with suitable Anchor Fasteners as required of following capacity. Test Certificates of all the Parameters along with Hydro test & Burst test (For Cylinder Body) Certificatefrom OEM / External NABL Accrediated Lab is to be submitted. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR . Capacity 4.5 Kg.(E-24.66.2) 105 Providing & Fixing of energy efficient /energy saving IP 20 LED direct retrofit Bulbin existing holder or fixture as required with system lumen efficacy ≥100 lm/Watt output ,pf 0.95 , CRI >70,minimum life time of minimum25000 Burning Hours with , 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be ofBIS standard andtrade mark certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing onhousing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM80) certificate / Report from OEM shall be submitted. All as per pre approved by engineer in charge . for additional technical parameters of product/ work, refer Annexure A attacheded with this BSR.9 Watt(E-17.9.3) 106 S&F following sizes (dia.) of ISI marked virgin material MMS ( IS:9537 P - III ) PVC conduit along withISI marked (IS:3419-1988) accessories as requiredinrecessincludingcutting the wall, covering conduit and making good the same as required. For additional technical parameters of product / work refer Annexure A attached with this BSR.20mm.(E-1.4.1) 107 Providing & Fixing ofBEEStar rated copper wounded double ball bearing capacitor start, aluminium body & Metallicblade ceilingfanConforming to all the performance requirements laid down in IS 374:2019 including all amendments, as applicable ; & Carry BIS licensing (i.e. ISI marking) with down rod up to 80 cm with secondary support safety cable ( steel rope) , cotter pin with 3 x 1.5 sq.mm pvc insulated flexible copper conductor making connection testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .1200 mm Sweep BEE 2 Star rated (service value >=4.5 to < 5 )(E-15.7.2) 108 Providing & Fixing of modular type 120 W Step Fan regulator duly ISI marked (IS 11037:1984 ) with CM/L no. printedmade out of unbreakable and fire retardant vergin poly carbonate with brass terminals and captive screws & silver alloy contact tipwith IP-20 rating ,includingall as per pre approved by Engineer in charge,making connections, testing etc. as required.For additional technical parameters of product / work refer Annexure A attached with this BSR5 step fan regulator 2 Module 360 dgree rotating(E-7.29.1) 109 Providing & Fixing of Heavy duty capacitor start, copper woundDouble ball bearing900/1400 RPM single phaseExhaustfan conforming to IS:2312 ISI marked in existing opening including making connections testing etc. as required. All as per pre approved by Engineer in charge.For additional technical parameters of products/ work, refer Annexure A attached with this BSR .300 mm sweep(900/1400 RPM)(E-15.12.1)E-15.2.1) 110 Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3mm thick water proofing membrane, black finished reinforced with non-woven polyester mattconsisting of a coat of bitumen primer for bitumen membran @ 0.40 Itr/sq.mt. by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ltr and viscosity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc., and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under Joint strength in longitudinal and transverse direction at 23°C as 650/450N/5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D-5147. The laying of membrane shall be got done through the authorized applicator of the manufacturer of membrane..3 mm thick(B-15.12) 111 Providing & laying broken glazed titles on roof ( broken glazed tilesnot less than 9 Kg/Sqm) on top of hot bitumen @ 1.7 Kg/Sqm. (1.40 Kg ofVG-40 (30/40 )grade and 0.30 Kg/Sqm. OfVG-10 (80/100) grade) and joints filled with cement mortar 1 :2 (1 cement:2 marble dust mixed with water proofing compund all complete as per direction of Engineer-in-charge. (B-10.24) 112 Repair of rolling shutter with replacement of shutter spring incl. removal of old spring in the existing rolling shutter incld. Cost of new spring(B-13.26) 113 Repair of rolling shutter with using any material such as bend repair , tightening of spring,bolt and screw etc complete (B-13.27) 114 Labour charges for repair to door / window without using any material such as applying randha (finishing) tightening of bolts & screw etc. (B-13.24) 115 Repair to damaged RCC slabs, beams and columns etc for strengthening with cement mortar 1 : 2 in following steps :- (I)Choping losse and cracked concrete to required depth, cleaning the exposed surface of steel and concrete with wire brush and sand papering , cleaning of concrete surface with water as necessary and getting dried. (II) Applying Epoxy primer on the exposed steel bars.(III)Applying Epoxy hardener and resin mix (as per manufectureds specification) on concrete and steel bars with brush.(IV) Speading dry cement mortar 1 : 2 mix over epoxy treated wet surface and allow it to dry for one day.(V) Plastering the surface with cement sand mortar 1 : 3 upto depth of 30mm complete.(VI) Cure the plastered surface for 15 days, All work including scaffolding etc. complete in all respect. .(B-13.29) 116 Repair to stone masonary in cement sand mortar 1:6 with old and new stone.. (B-13.12) 117 Pointingonstonemasonryincementsandmortar 1:3 (1 cement : 3 sand) :Raised and cut pointing.(B-12.31.2) 118 Providing and laying in position specified grade ofcement concrete for RCC structural elements upto floor five level including curing, compaction, finishing with rendering in cement sand mortar 1:3 (1 cement: 3 coarse sand) and making good the joints and cost of plastizers (if required ) excluding the cost of centering, shuttering and reinforcementfor Walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc.M20 grade Nominal Mix / Design Mix(B-4.2) 119 Centering & shuttering with plywood or steel sheets including strutting, propping bracing both ways with steel propsand removal of formwork for upto floor five level for : Walls (any thickness) including attached pilasters,buttressesplinthandstring course. (B-4.10.1) 120 Finishing with neat cement (punning).(B-12.7) 121 Providing and fixing concertina coil fencing with required dia 610 mm (having 15 nos. round per 6 metre length) up to 3m height of wall with existing angle iron Y shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T. stud tied with GI staples and GI clips to retain horizontal including necessary bolts or GI barbed wire tied to angle iron all complete as per direction of Engineer In Charge with reinforced barbed tape (R.B.T.)/Spring core(2.5 mm thick) wire of high tensile strength of 165 kg/sq.mm with tape (0.52 mm thick) and weight 43.478 gm/metre (Cost of MS angle, CC block shall be paid extra)(B-9.37)
