E Tender For The Furnishing Works At Ernakulam , E-Tender For The Furnishing Works At Ernakulam , Modular Workstation With Side Storage And With Sharing Partition*Second Floor Audit Dpt, Accounts, Pd/General Section & Legal Cell Workstation:Partition Size: 1500/1500 Mm L X 50Mm D X 1050Mm Ht. (T Type) Table Size: 1500Mm L X 600Mm D X 750Mm Ht. A) Frame Is Made Up Of 50Mm Powder Coated Ms Sections With Necessary Slotting For Wiring Throughout The Height And The Width Of The Partition. It Also Consists Of Two Race Ways One At The Floor Level For Networking And Another Below The Table Top For Fixing Electrical Plug Points. Frame Will Be Covered With Elegant Powder Coated Aluminium Top & Side Trim.B) Tiles Are Made Up Of 9 Mm Mdf Boards (Fabric/Laminated Finish) And Are Fixed To The Framework Which Also Includes A Writing Board /Pin Up Board For Each Workstation.C) Worktop Made Up Of 25 Mm Pre-Laminated Particle Board With Pvc Edge Binding With Vertical Supports With 25Mm Thick Prelaminated Particle Board.D) Side Storage Top With 25Mm Thick Plb And The Rest Made Of 18Mm Thick Pre Laminated Particle Board With 2 Drawers On Top Withtelescopic Sliders, Handle And Individual Lock And Open Storage Below , Modular Workstation With Side Storage And With L Type Partition *Second Floor Accounts, Pd/General Section & Legal Cell Workstation:Partition Size: A) 1500/1500Mm L X 50Mm D X 1050Mm Ht. (L Type)Table Size: 1500Mm L X 600Mm D X 750Mm Ht. A) Frame Is Made Up Of 50Mm Powder Coated Ms Sections With Necessary Slotting For Wiring Throughout The Height And The Width Of The Partition. It Also Consists Of Two Race Ways One At The Floor Level For Networking And Another Below The Table Top For Fixing Electrical Plug Points. Frame Will Be Covered With Elegant Powder Coated Aluminium Top & Side Trim.B) Tiles Are Made Up Of 9 Mm Mdf Boards (Fabric/Laminated Finish) And Are Fixed To The Framework Which Also Includes A Writing Board /Pin Up Board For Each Workstation.C) Worktop Made Up Of 25 Mm Pre-Laminated Particle Board With Pvc Edge Binding With Vertical Supports With 25Mm Thick Prelaminated Particle Board.D) Side Storage Top With 25Mm Thick Plb And The Rest Made Of 18Mm Thick Pre Laminated Particle Board With 2 Drawers On Top Withtelescopic Sliders, Handle And Individual Lock And Open Storage Below , Cabin Table With Side Storage-Table Top - 25Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. Understructure – Legs Made Of 25Mm Thick Pre Lam-Particle Board And Modesty & Side Credenza Made Of 18Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. *Second Floor Audit Officer , Accounts Officer ,Pa To Secretary & Ca To Secretary Room Table:A) Table Size: 1800Mm L X 750Mm D X 750Mm Ht. Side Table Cum Storage: 900Mm L X 450Mm D X 750Mm Ht. (Drawer And Open Storage) , *Second Floor Additional Secretary & Secretary Cabin Table:B)Table Size: 2100Mm L X 1200Mm D X 750Mm Ht. Side Table Cum Storage: 900Mm L X 450Mm D X 750Mm Ht. , Counter Table With Side Storage *Second Floor Superindent Counter Table:Executive Table With Privacy Partition Size: A)Table Size: 1500Mm L X 750Mm D X 750Mm Ht.Side Storage: 900Mm L X 450Mm D X 750Mm Ht , *Second Floor Pd/General Section Counter Table:B) Table Size:1500Mm L X 750Mm D X 750Mm Ht.Side Storage: 900Mm L X 450Mm D X 750Mm Ht. , Pedestal With Single Drawer And Shutter ( For Workstations) Size : 400Mm L X 450Mm D X 650Mm Ht.Made Of 18 Mm Thick Pre Laminated Particle Board With Telescopic Drawer Runners , Handle And Individual Lock. , 3Door Storage-Size: 1200Mm L X 400Mm D X 1200Mm Ht.Made Of 18Mm Thick Pre Laminated Board With Pvc Edge Binding, With Multipurpose Lock, D Handle And Box Hinges With Necessary Intermediate Vertical Supports Where Ever Necessary To Avoid Shelf Bending Issue. , Storage-Size : 1500Mm L X 450Mm D X 750Mm Ht. Made Of 18 Mm Thick Pre Laminated Board With Pvc Edge Binding, With Multipurpose Lock, D Handle And Box Hinges , Conference Table With 02 Nos Of Pop Up Box ( 8 Module Without Switch &Socket)Size : 4800Mm L X 1200Mm D X 750Mm Ht. (2 Pieces Of 2400Mm Joined Together) * Table Top - Made Of 16Mm 710 Grade Plywood Finished With 1Mm Laminate (Wooden Suede) Edges In Double Thick Finished With 2Mm Thick Pvc Edge Binding Matching With The Laminate Shade.* Understructure – Box Type Legs Made Of 16 Mm 710 Grade Plywood Finished With 1Mm Laminate (Wooden Suede) , Office Atndr Room Table With Side Storage-Table Size : 3370Mm L X 450Mm D X 750Mm Ht. (2 Pieces Of 169Mm Joined Together)Side Storage Size : 3370Mm L X 450Mm D X 750Mm Ht. (2 Pieces Of 169Mm Joined Together)A)Table Top - 25Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. Understructure – Legs Made Of 25Mm Thick Pre Lam-Particle Board And Modesty & Side Credenza Made Of 18Mm Thick Pre Lam-Particle Board With Pvc Edge Bindingb)Side Storage Top With 25Mm Thick Plb And The Rest Made Of 18Mm Thick Pre Laminated Particle Board With 2 Drawers On Top Withtelescopic Sliders, Handle And Individual Lock And Open Storage Below , Dinning Room Table- Second Floor 4 Seater Dinningtabletable Size : 4420Mm L X 700Mm D X 750Mm Ht. (2 Pieces Of 2210Mm Joined Together)A)Table Top - 25Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. B)Understructure – Legs Made Of 25Mm Thick Pre Lam-Particle Board And Modesty & Side Credenza Made Of 18Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. , Second Floor2 Seater Dinning Tabletable Size : 700Mm L X 700Mm D X 750Mm Ht.A) Table Top - 25Mm Thick Pre-Lam-Particle Board With Pvc Edge Binding. B)Understructure - Box Type Legs Made Of 25Mm Thick Pre Lam-Particle Board And Modesty & Side Credenza Made Of 18Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. , Waiting Area Counter Table-Table Size : 1930Mm L X 400Mm D X 750Mm Ht.A) Table Top - 25Mm Thick Pre-Lam-Particle Board With Pvc Edge Binding. B)Understructure - Legs Made Of 25Mm Thick Pre Lam-Particle Board And Modesty & Side Credenza Made Of 18Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. , Providing And Supplying Of Encardo 3Str Dimensions W X H X D (Cm) - 179 X 85 X 83.5 Finish Color - Cappuccino Net Weight (Kg) - 85 Primary Material - Solid Wood Upholstery Material - Leatherette Seat Height (Cm) - 55 Warranty - 1 Year Style - Contemporary & Modern Delivery Condition - Knock Down , Providing And Supplying Of Encardo 2Str Dimensions W X H X D (Cm) - 125 X 85 X 83.5 Thickness Of Plywood Used(Mm) : 12 Mm Leg Material: * Material Of Leg : (Plastic / Insert Moulding / Wooden/ Ms + Chrome Plating / Ss) :-Wooden Hanlde Is The Leg Frame Material (Tropical Wood / Pine Wood/ Rubber Wood): Pine Wood Seat Height (Cm) - 47 Warranty - 1 Year , Providing, Supplying And Placing Of High Back Chair.Seat/Back Assembly : The Cushioned Seat Should Bemade Of Injection Molded Plastic Outer & Inner. Plastic Inner Should Beupholstered With Pure Leather And Moulded High Resilience (Hr) Polyurethane Foam Of Density 45±2 Kg/M3,And Hardness Load 16 ± 2 Kgffor 25% Compression.The Cushioned Back Should Bemade Of Pu Foam With Insitu Molded Ms E.R.W Round Tube Of Size 1.9±0.03Cm X 0.16 ±0.0128Cm. It Upholstered With Pure Leather. Seat Size : 47.6 Cm. (W) X 49.2 Cm. (D) Back Size : 47.5 Cm. (W) X 77 Cm. (D) Armrests: The Armrest Top Should Bemoulded From Polyurethane(Pu), Upholstered In Pure Leather And Mounted On To A Drop Lift Adjustable Type Tubular Armrest Support Made Of 03.81±0.03 Cm X 0.2±0.01 Cm Thk M.S E.R.W Tube Having Chrome Plated Finish.The Armrest Height Adjustable Up To 6.5±0.5Cm In 5 Steps. Active Bio-Synchro Mechanism: The Adjustable Tilting Mechanism Should Bedesigned With The Following Features: • 360° Revolving Type. • Front-Pivot For Tilt With Feet Resting On Ground And Continuous Lumbar Support Ensuring More Comfort. • Tilt Tension Adjustment Can Be Operated In Seating Position. • 5-Position Tilt Limiter Giving Option Of Variable Tilt Angle To The Chair. • Seat/Back Tilting Ratio Of 1: 2 • The Mechanism Housing Should Bemade Up Of Hpdc Aluminium Black Powder Coated. Seat Depth Adjustment: Seat Depth Adjustment Should Beintegrated In The Seat Through A Sliding Mechanism. Seat Depth Adjustment Range Should Beof 6.0±0.5 Cm. Adjustable Back Support: Back Frame Should Beconnected To The Up/Dn Mechanism Housed In Plastic T Spine. It Can Be Adjusted In The Range Of 7.42±0.5 Cm For The Comfortable Back Support To Suit Individual Need. Pneumatic Ht. Adjustment: The Pneumatic Height Adjustment Has An Adjustment Stroke Of 10.0±0.3 Cm. Pedestal Assembly The Pedestal Should Behigh Pressure Die Cast Polishedaluminium And Fitted With 5 Nos. Twin Wheel Castors. The Pedestal Should Be65.0 ± 0.5Cm. Pitch-Center Dia.(75.0 ± 1.0Cm. With Castors.) Twin Wheel Castors:The Twin Wheel Castors Should Beinjection Mouldedin Black Polypropylene. Overall Dimensions Of Chair Seat Height -44.5 To 54.5 Cm. Height -114.0-131.5 Cm. Width & Depth Of Chair As Measured From Base - Width-76.1 Cm And Depth-76.1 Cm , Mid Back Office Chair.Providing & Laying Revolving Chair With Arm Rest. The Seat And Back Cushion Of The Chairs Should Be Pressed On 12Mm Hot Press Moulded Ply The Seat Cushion Of The Chair Should Be Made Up Of 50Mm Thick High Density Of 45±2 Kg/M3 Polyurethane Mould And Back Cushion Should Be Made Up Of 38Mm Thick High Density 33±2 Kg/M3. The Polyurethane Foam Shall Be As Per Manufacturer’S Specification. The Hardness Of Foam Shall Be 20 Kg On Hampden Machine And 25% Compression And It Should Be Covered With Fabric As Per Manufacturer’S Shade Card .The Arms Of The Chairs Should Be Black. The Gas Lift Mechanism Should Be Tested As Per Bifma X 05.01.2002 Standards .The Pedestal Should Be Five Legged Injection Moulded In Black 30% Glass –Filled Nylon And Fitted With 5 Nos Twin Wheel Castors. The Castors Of The Chairs Should Be Glass Filled, Twin Wheel Castors Confirming To Bifma Standards X 05.01.2002 Tested To Perform 1,00,000 Cycles With 225 Lbs Load. It Should Have Synchro Single Point Locking Arrangement. (Note -The Back And Base Of Chair Should Be Supplied With Fabric Upholstered ) Overall Height Of Chair Should Be Minimum 970 Mm ( Inclusive Of Maximum Adjustment Of Gas Lift Mechanism ) , Visitor Chair - Model Smat Cantilever The Seat And Back Are Made Up Of 1.2 Cm Thick Hot Pressed Plywood, Upholstered With Fabric And Moulded Polyurethane Foam With Pvc Lipping All Around. The Back Foam Is Designed With Contoured Lumbar Support For Extra Comfort. Back Size: 49.0Cm.(W) X 47.0Cm.(H) Seat Size: 49.0Cm.(W) X 44.0Cm.(D). Polyurethane Foam: The Polyurethane Foam Is Moulded With Density = 45 +/-2 Kg/M3 And Hardness = 20 +/- 2 On Hampden Machine At 25% Compression. Tubular Frame: The Tubular Frame Is Cantilever Type & Made Of Dia.2.54Cm.(1”)X 14 Bg M.S. E.R.W. Tube And Black Powder Coated. , Conference Hall Chair-Providing, Supplying And Placing Of Mid Back Chair. Seat/Back Assembly : The Cushioned Seat Should Be Made Of Injection Molded Plastic Outer & Inner. Plastic Inner Should Be Upholstered With Leatherette And Moulded High Resilience (Hr) Polyurethane Foam Of Density 45±2 Kg/M3,And Hardness Load 16 ± 2 Kgf As Per Is:7888 For 25% Compression. The Cushioned Back Should Be Made Of Pu Foam With Insitu Molded Ms E.R.W Round Tube Of Size 1.9±0.03Cm X 0.16 ±0.0128Cm. It Upholstered With Leatherette. Seat Size : 47.0 Cm. (W) X 48.0 Cm. (D) Mid Back Size: 47.7 Cm. (W) X 60.1 Cm. (D) Armrests: The Armrest Top Should Be Moulded From Polyurethane(Pu) And Mounted On To A Drop Lift Adjustable Type Tubular Armrest Support Made Of 03.81±0.03 Cm X 0.2±0.01 Cm Thk M.S. E.R.W Tube Having Chrome Plated Finish.The Armrest Height Adjustable Up To 6.5±0.5Cm In 5 Steps. Active Bio-Synchro Mechanism : The Adjustable Tilting Mechanism Should Be Designed With The Following Features: • 360 Revolving Type. • Front-Pivot For Tilt With Feet Resting On Ground And Continuous Lumbar Support Ensuring More Comfort. • Tilt Tension Adjustment Can Be Operated In Seating Position. • 5-Position Tilt Limiter Giving Option Of Variable Tilt Angle To The Chair. • Seat/Back Tilting Ratio Of 1: 2 • The Mechanism Housing Should Be Made Up Of Hpdc Aluminium Black Powder Coated. Seat Depth Adjustment: Seat Depth Adjustment Should Be Integrated In The Seat Through A Sliding Mechanism. Seat Depth Adjustment Range Should Be Of 6.0±0.5 Cm. Adjustable Back Support : Back Frame Should Be Connected To The Up/Dn Mechanism Housed In Plastic T Spine. It Can Be Adjusted In The Range Of 7.42±0.5 Cm For The Comfortable Back Support To Suit Individual Need. Pneumatic Ht. Adjustment : The Pneumatic Ht Adjustment Has An Adjustment Stroke Of 10.0±0.3 Cm. Pedestal Assembly: The Pedestal Should Be High Pressure Die Cast Polished Aluminium And Fitted With 5 Nos. Twin Wheel Castors. The Pedestal Should Be 65.0 ± 0.5Cm. Pitch-Center Dia.(75.0 ± 1.0Cm. With Castors.) Twin Wheel Castors:The Twin Wheel Castors Should Beinjection Moulded In Black Pp Having 6.0± 0.1Cm Wheel Diameter. Overall Dimensions Of Chair Seat Height -43.1-53.1Cm Height -96.5-114.0.Cm. Width & Depth Of Chair As Measured From Base - Width-76.1 Cm And Depth-76.1 Cm , Providing, Supplying And Placing Of Waiting Chair. Seat Shell :The Seat Shell Should Bea Welded Assembly Of Seat,Back And Side Frame. The Seat And Back Should Bemade Of 0.12±0.013Cm Thk Cr Steel Sheet With Oblong Perforations.They Should Bewelded To Sideframe Of Size 3.2±0.05Cm X 0.5 ± 0.05 Cm Thk Hr Steel.The Welded Assembly Should Bepowder Coated ( Dft 40-60 Microns ). The Seat Has A Front Water Fall Edge To Provide Popliteal Clearance For Comfortable Seating. It Also Has A Buttock Support Curve That Not Only Provides Rear Support But Also Prevents Small Children From Falling Through The Gap Between Seat And Back. Clean And Flat Surfaces Of Seat And Back Aids In Easy Maintenance. * Seat Size : 47.8 Cm (W) X 44.6 Cm (D) * Back Size : 41.6 Cm (W) X 23.0 Cm (H)Understructure Assembly Consshould Be Ts Of Connecting Beam And Leg Assembly Made Of M.S. E.R.W. Oblong Tube Of Size 7.5±0.03Cm X 2.5±0.03Cm X 0.2±0.016Cm Thk.The Welded Structure Assembly Should Bepowder Coated ( Dft 40-60 Microns ).The Leg Assembly Should Befitted With Shoes And Levellers In Nylon. The Leg Structure Should Bedesigned With Minimal Should Be A Of Contact Close To Ground Providing Easy Access For Cleaning Purposes. The Shoes Fitted To Leg Assembly Help In Aligning The Structure For Back To Back Arrangements. Levellers Take Cshould Beof Uneven Flooring.Connecting Beam Should Befitted With Snap Locking End Cap.Lt Also Aids In Side-By-Side Understructure Alignment . Armrest Assembly Consshould Be Ts Of Armrest Frame And Armrest Pad . The Armrest Frame Should Bemade Up Of Size 3.175±0.05Cm X 0.47±0.027Cm Thk Hr Steel And It Should Bepowder Coated ( Dft 40-60 Microns ). Armrest Pad Should Beinjection Molded In Nylon And Should Befitted Onto The Armrest Frame. Overall Dimensions Of Chair Seat Height - 44.1 Cm. Height - 78.5 Cm. Width & Depth Of Chair As- Width-169.5Cm And Depth-63.8 Cm. , Modular Workstation With Side Storage And With Sharing Partition*Second Floor Audit Dpt, Accounts, Pd/General Section & Legal Cell Workstation:Partition Size: 1500/1500 Mm L X 50Mm D X 1050Mm Ht. (T Type) Table Size: 1500Mm L X 600Mm D X 750Mm Ht. A) Frame Is Made Up Of 50Mm Powder Coated Ms Sections With Necessary Slotting For Wiring Throughout The Height And The Width Of The Partition. It Also Consists Of Two Race Ways One At The Floor Level For Networking And Another Below The Table Top For Fixing Electrical Plug Points. Frame Will Be Covered With Elegant Powder Coated Aluminium Top & Side Trim.B) Tiles Are Made Up Of 9 Mm Mdf Boards (Fabric/Laminated Finish) And Are Fixed To The Framework Which Also Includes A Writing Board /Pin Up Board For Each Workstation.C) Worktop Made Up Of 25 Mm Pre-Laminated Particle Board With Pvc Edge Binding With Vertical Supports With 25Mm Thick Prelaminated Particle Board.D) Side Storage Top With 25Mm Thick Plb And The Rest Made Of 18Mm Thick Pre Laminated Particle Board With 2 Drawers On Top Withtelescopic Sliders, Handle And Individual Lock And Open Storage Below , Modular Workstation With Side Storage And With L Type Partition *Second Floor Accounts, Pd/General Section & Legal Cell Workstation:Partition Size: A) 1500/1500Mm L X 50Mm D X 1050Mm Ht. (L Type)Table Size: 1500Mm L X 600Mm D X 750Mm Ht. A) Frame Is Made Up Of 50Mm Powder Coated Ms Sections With Necessary Slotting For Wiring Throughout The Height And The Width Of The Partition. It Also Consists Of Two Race Ways One At The Floor Level For Networking And Another Below The Table Top For Fixing Electrical Plug Points. Frame Will Be Covered With Elegant Powder Coated Aluminium Top & Side Trim.B) Tiles Are Made Up Of 9 Mm Mdf Boards (Fabric/Laminated Finish) And Are Fixed To The Framework Which Also Includes A Writing Board /Pin Up Board For Each Workstation.C) Worktop Made Up Of 25 Mm Pre-Laminated Particle Board With Pvc Edge Binding With Vertical Supports With 25Mm Thick Prelaminated Particle Board.D) Side Storage Top With 25Mm Thick Plb And The Rest Made Of 18Mm Thick Pre Laminated Particle Board With 2 Drawers On Top Withtelescopic Sliders, Handle And Individual Lock And Open Storage Below , Counter Table With Side Storage & With L Type Partition*Third Floor Superindent Counter Table: Modular Partition: 1500/1500Mm L X 50Mm D X 1050Mm Ht.Table Size : 1500Mm L X 750Mm D X 750Mm Ht.Side Storage Size : 900Mm L X 450Mm D X 750Mm Ht.) Frame Is Made Up Of 50Mm Powder Coated Ms Sections With Necessary Slotting For Wiring Throughout The Height And The Width Of The Partition. It Also Consists Of Two Race Ways One At The Floor Level For Networking And Another Below The Table Top For Fixing Electrical Plug Points. Frame Will Be Covered With Elegant Powder Coated Aluminium Top & Side Trim.B) Tiles Are Made Up Of 9 Mm Mdf Boards (Fabric/Laminated Finish) And Are Fixed To The Framework Which Also Includes A Writing Board /Pin Up Board For Each Workstation.C) Worktop Made Up Of 25 Mm Pre-Laminated Particle Board With Pvc Edge Binding With Vertical Supports With 25Mm Thick Prelaminated Particle Board.D) Side Storage Top With 25Mm Thick Plb And The Rest Made Of 18Mm Thick Pre Laminated Particle Board With 2 Drawers On Top Withtelescopic Sliders, Handle And Individual Lock And Open Storage Below , Cabin Table With Side Storage-*Third Floor Deputy Secretary Office Table, Revenue Office Table, Pb, Cho-1,Hs-1 Cabin Table:) Table Size: 1800Mm L X 750Mm D X 750Mm Ht.Side Table Cum Storage: 900Mm L X 450Mm D X 750Mm Ht. (Drawer And Open Storage)Table Top - 25Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. Understructure – Legs Made Of 25Mm Thick Pre Lam-Particle Board And Modesty & Side Credenza Made Of 18Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. , Counter Table With Side Storage-*Third Floor It Work Station Table , Atndr At Deputy Secretary &Pb Cabin & Propery Tax Workstation:A)Table Size: 1500Mm L X 600Mm D X 750Mm Ht.Side Storage: 900Mm L X 450Mm D X 750Mm Httable Top - 25Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. Understructure – Legs Made Of 25Mm Thick Pre Lam-Particle Board And Modesty & Side Credenza Made Of 18Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. , Pedestal With Single Drawer And Shutter ( For Workstations)Size : 400Mm L X 450Mm D X 650Mm Ht.Made Of 18 Mm Thick Pre Laminated Particle Board With Telescopic Drawer Runners , Handle And Individual Lock. , 3Door Storage -Size: 1200Mm L X 400Mm D X 1200Mm Ht.Made Of 18Mm Thick Pre Laminated Board With Pvc Edge Binding, With Multipurpose Lock, D Handle And Box Hinges With Necessary Intermediate Vertical Supports Where Ever Necessary To Avoid Shelf Bending Issue. , Storage-Size : 1500Mm L X 450Mm D X 750Mm Ht. Made Of 18 Mm Thick Pre Laminated Board With Pvc Edge Binding, With Multipurpose Lock, D Handle And Box Hinges , Office Atndr Table Office Atndr Table-Third Floor Atndr Office Room Table 1Table Size : 4670Mm L X 500Mm D X 750Mm Ht. (3 Pieces Of 1560Mm Joined Together)A)Table Top - 25Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. B)Understructure – Legs Made Of 25Mm Thick Pre Lam-Particle Board And Modesty & Side Credenza Made Of 18Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. , Third Floor Atndr Office Room Table 2-Table Size : 1750Mm L X 500Mm D X 750Mm Ht.A)Table Top - 25Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. B)Understructure – Legs Made Of 25Mm Thick Pre Lam-Particle Board And Modesty & Side Credenza Made Of 18Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. , Third Floor Atndr Office Room Table 3 ( Revenue, Ri Office)Table Size : 2800Mm L X 500Mm D X 750Mm Ht ( 2 Pieces Of 1400Mm Joined Together)A)Table Top - 25Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. B)Understructure – Legs Made Of 25Mm Thick Pre Lam-Particle Board And Modesty & Side Credenza Made Of 18Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. , Third Floor Atndr Office Room Table 3 ( Property Tax)Table Size : 5580Mm L X 500Mm D X 750Mm Ht. (3 Pieces Of 1860Mm Joined Together)A)Table Top - 25Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. B)Understructure – Legs Made Of 25Mm Thick Pre Lam-Particle Board And Modesty & Side Credenza Made Of 18Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. , Third Floor Atndr Office Room Table 4( Revenue Non Tax)Table Size : 2500Mm L X 500Mm D X 750Mm Ht. (2 Pieces Of 1250Mm Joined Together)A)Table Top - 25Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. B)Understructure – Legs Made Of 25Mm Thick Pre Lam-Particle Board And Modesty & Side Credenza Made Of 18Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. , Third Floor Atndr Office Room Table 4( Revenue Non Tax) Table Size : 3600Mm L X 500Mm D X 750Mm Ht. (2 Pieces Of 1810Mm Joined Together)A)Table Top - 25Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. B)Understructure – Legs Made Of 25Mm Thick Pre Lam-Particle Board And Modesty & Side Credenza Made Of 18Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. , Cashier Counetr Table-Third Floor Waiting Area Cashier Counter Tabletable Size : 1200Mm L X 400Mm D X 750Mm Ht. A)Table Top - 25Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. B)Understructure – Legs Made Of 25Mm Thick Pre Lam-Particle Board And Modesty & Side Credenza Made Of 18Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. , Dinning Room Table- Table1 Size : 2400Mm L X 750Mm D X 750Mm Ht.)Table Top - 25Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. B)Understructure – Legs Made Of 25Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. , Dinning Room Table-Table2size : 700Mm L X 700Mm D X 750Mm Ht.Table Top - 25Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. B)Understructure – Legs Made Of 25Mm Thick Pre Lam-Particle Board With Pvc Edge Binding , Providing, Supplying And Placing Of Waiting Chair. Seat Shell :The Seat Shell Should Bea Welded Assembly Of Seat,Back And Side Frame. The Seat And Back Should Bemade Of 0.12±0.013Cm Thk Cr Steel Sheet With Oblong Perforations.They Should Bewelded To Sideframe Of Size 3.2±0.05Cm X 0.5 ± 0.05 Cm Thk Hr Steel.The Welded Assembly Should Bepowder Coated ( Dft 40-60 Microns ). The Seat Has A Front Water Fall Edge To Provide Popliteal Clearance For Comfortable Seating. It Also Has A Buttock Support Curve That Not Only Provides Rear Support But Also Prevents Small Children From Falling Through The Gap Between Seat And Back. Clean And Flat Surfaces Of Seat And Back Aids In Easy Maintenance. * Seat Size : 47.8 Cm (W) X 44.6 Cm (D) * Back Size : 41.6 Cm (W) X 23.0 Cm (H)Understructure Assembly Consshould Be Ts Of Connecting Beam And Leg Assembly Made Of M.S. E.R.W. Oblong Tube Of Size 7.5±0.03Cm X 2.5±0.03Cm X 0.2±0.016Cm Thk.The Welded Structure Assembly Should Bepowder Coated ( Dft 40-60 Microns ).The Leg Assembly Should Befitted With Shoes And Levellers In Nylon. The Leg Structure Should Bedesigned With Minimal Should Be A Of Contact Close To Ground Providing Easy Access For Cleaning Purposes. The Shoes Fitted To Leg Assembly Help In Aligning The Structure For Back To Back Arrangements. Levellers Take Cshould Beof Uneven Flooring.Connecting Beam Should Befitted With Snap Locking End Cap.Lt Also Aids In Side-By-Side Understructure Alignment . Armrest Assembly Consshould Be Ts Of Armrest Frame And Armrest Pad . The Armrest Frame Should Bemade Up Of Size 3.175±0.05Cm X 0.47±0.027Cm Thk Hr Steel And It Should Bepowder Coated ( Dft 40-60 Microns ). Armrest Pad Should Beinjection Molded In Nylon And Should Befitted Onto The Armrest Frame. Overall Dimensions Of Chair Seat Height - 44.1 Cm. Height - 78.5 Cm. Width & Depth Of Chair As- Width-169.5Cm And Depth-63.8 Cm. , Mid Back Office Chair.Providing & Laying Revolving Chair With Arm Rest. The Seat And Back Cushion Of The Chairs Should Be Pressed On 12Mm Hot Press Moulded Ply The Seat Cushion Of The Chair Should Be Made Up Of 50Mm Thick High Density Of 45±2 Kg/M3 Polyurethane Mould And Back Cushion Should Be Made Up Of 38Mm Thick High Density 33±2 Kg/M3. The Polyurethane Foam Shall Be As Per Manufacturer’S Specification. The Hardness Of Foam Shall Be 20 Kg On Hampden Machine And 25% Compression And It Should Be Covered With Fabric As Per Manufacturer’S Shade Card .The Arms Of The Chairs Should Be Black. The Gas Lift Mechanism Should Be Tested As Per Bifma X 05.01.2002 Standards .The Pedestal Should Be Five Legged Injection Moulded In Black 30% Glass –Filled Nylon And Fitted With 5 Nos Twin Wheel Castors. The Castors Of The Chairs Should Be Glass Filled, Twin Wheel Castors Confirming To Bifma Standards X 05.01.2002 Tested To Perform 1,00,000 Cycles With 225 Lbs Load. It Should Have Synchro Single Point Locking Arrangement. (Note -The Back And Base Of Chair Should Be Supplied With Fabric Upholstered ) Overall Height Of Chair Should Be Minimum 970 Mm ( Inclusive Of Maximum Adjustment Of Gas Lift Mechanism ) , Visitor Chair - Model Smat Cantilever The Seat And Back Are Made Up Of 1.2 Cm Thick Hot Pressed Plywood, Upholstered With Fabric And Moulded Polyurethane Foam With Pvc Lipping All Around. The Back Foam Is Designed With Contoured Lumbar Support For Extra Comfort. Back Size: 49.0Cm.(W) X 47.0Cm.(H) Seat Size: 49.0Cm.(W) X 44.0Cm.(D). Polyurethane Foam: The Polyurethane Foam Is Moulded With Density = 45 +/-2 Kg/M3 And Hardness = 20 +/- 2 On Hampden Machine At 25% Compression. Tubular Frame: The Tubular Frame Is Cantilever Type & Made Of Dia.2.54Cm.(1”)X 14 Bg M.S. E.R.W. Tube And Black Powder Coated. , Providing, Supplying And Placing Of Boltless Shelving System Of Height 2100Mm, Length 1300Mm & Depth 500Mm With 6 Panels. Upright Is Roll-Formed Construction Made Up Of Single Piece Having Slots At 25Mm Pitch Upright Typeupright G50 Profile Width 50 Mm Profile Depth 37 Mm No Of Pieces Single Panel Adjustability 25 Mm Material Quality Min Ys=210 Mpa Mfg Process Roll Forming Finish Powder Coated Colour Oxford Blue Bracingis Formed Single Piece Section Which Connects Two Vertical Uprights & Makes A Frame Bracing Type Battened Type Section Flat With Edge Hem Bend And Middle Rib Material Thickness 1.2Mm Mfg Process Press Brake Forming Connectivity Hooking & Pin Assembly No Of Fasteners 2 Nos Of M6x10 Plastic Rivet Pin Surface Finish Galvanized Base Plate G50 Base Are Used To Transfer The Upright Load Into Ground & Also Act As A Connecting Member Between Ground & Upright. Width 64Mm Depth 60Mm Thickness 2.0Mm Connectivity Grouting No Of Anchor Bolt 1 No Of M8x51 Fastener Type Coach Bolt No Of Fasteners To Connect Upright 1 No Of M6x15 Fastener Type Hex. Bolt & Nut Mfg. Process Press Forming Finish Galvanized Shelf Panels Are The Load Carrying Members Which Are Hooked Into The Uprights Via Shelf Clips. ‘4’ Nos. Of Clips Are Used Per Panel. Width 1300 Mm In 50 Pitch. Depth 300 To 600Mm In 50 Pitch. Thickness 0.8 Mm Range Where Panel Cannot Be Offered Refer Shelf Panel Load Chart Height 32Mm No Of Bends 14 Sharp Edges No Sharp Edges Mfg. Process Roll Formed Usage Decking Surface Fasteners No Divider Adjustability 50Mm Mounting Using ‘4’ Nos. Of Shelf Clips Surface Finish Galvanized Shelf Clip Shelf Panels Are Mounted Using This Shelf Clips. Profile Section 70 X 17 X 12Mm Material Thickness 2.3Mm Mfg. Process Blanking & Punching No Of Bend 2 Connectivity Insertion Surface Finish Galvanized Back Ties Are The Critical Members In Ensuring Stability. Usage Stability Dia. Of Tie Rod 5Mm Size Of Turn Buckle 90Mm Connectivity – Tie Rod Cleat Hooking Fasteners ‘1’ No Of Plastic Rivet Pin / Cleat Mfg. Process – Tie Rod Bending Surface Finish Galvanized , Modular Workstation With Side Storage And With Sharing Partition*Second Floor Audit Dpt, Accounts, Pd/General Section & Legal Cell Workstation:Partition Size: 1500/1500 Mm L X 50Mm D X 1050Mm Ht. (T Type) Table Size: 1500Mm L X 600Mm D X 750Mm Ht. A) Frame Is Made Up Of 50Mm Powder Coated Ms Sections With Necessary Slotting For Wiring Throughout The Height And The Width Of The Partition. It Also Consists Of Two Race Ways One At The Floor Level For Networking And Another Below The Table Top For Fixing Electrical Plug Points. Frame Will Be Covered With Elegant Powder Coated Aluminium Top & Side Trim.B) Tiles Are Made Up Of 9 Mm Mdf Boards (Fabric/Laminated Finish) And Are Fixed To The Framework Which Also Includes A Writing Board /Pin Up Board For Each Workstation.C) Worktop Made Up Of 25 Mm Pre-Laminated Particle Board With Pvc Edge Binding With Vertical Supports With 25Mm Thick Prelaminated Particle Board.D) Side Storage Top With 25Mm Thick Plb And The Rest Made Of 18Mm Thick Pre Laminated Particle Board With 2 Drawers On Top Withtelescopic Sliders, Handle And Individual Lock And Open Storage Below , Modular Workstation With Side Storage And With L Type Partition *Second Floor Accounts, Pd/General Section & Legal Cell Workstation:Partition Size: A) 1500/1500Mm L X 50Mm D X 1050Mm Ht. (L Type)Table Size: 1500Mm L X 600Mm D X 750Mm Ht. A) Frame Is Made Up Of 50Mm Powder Coated Ms Sections With Necessary Slotting For Wiring Throughout The Height And The Width Of The Partition. It Also Consists Of Two Race Ways One At The Floor Level For Networking And Another Below The Table Top For Fixing Electrical Plug Points. Frame Will Be Covered With Elegant Powder Coated Aluminium Top & Side Trim.B) Tiles Are Made Up Of 9 Mm Mdf Boards (Fabric/Laminated Finish) And Are Fixed To The Framework Which Also Includes A Writing Board /Pin Up Board For Each Workstation.C) Worktop Made Up Of 25 Mm Pre-Laminated Particle Board With Pvc Edge Binding With Vertical Supports With 25Mm Thick Prelaminated Particle Board.D) Side Storage Top With 25Mm Thick Plb And The Rest Made Of 18Mm Thick Pre Laminated Particle Board With 2 Drawers On Top Withtelescopic Sliders, Handle And Individual Lock And Open Storage Below , Superindent Table With Side Storage And With L Type Partition *Fourth Floor Superindent Counter Table:Modular Partition: 1500/1500Mm L X 50Mm D X 1050Mm Ht.Table Size : 1800Mm L X 750Mm D X 750Mm Ht.A) Frame Is Made Up Of 50Mm Powder Coated Ms Sections With Necessary Slotting For Wiring Throughout The Height And The Width Of The Partition. It Also Consists Of Two Race Ways One At The Floor Level For Networking And Another Below The Table Top For Fixing Electrical Plug Points. Frame Will Be Covered With Elegant Powder Coated Aluminium Top & Side Trim.B) Tiles Are Made Up Of 9 Mm Mdf Boards (Fabric/Laminated Finish) And Are Fixed To The Framework Which Also Includes A Writing Board /Pin Up Board For Each Workstation.C) Worktop Made Up Of 25 Mm Pre-Laminated Particle Board With Pvc Edge Binding With Vertical Supports With 25Mm Thick Prelaminated Particle Board.D) Side Storage Top With 25Mm Thick Plb And The Rest Made Of 18Mm Thick Pre Laminated Particle Board With 2 Drawers On Top Withtelescopic Sliders, Handle And Individual Lock And Open Storage Below , Cabin Table With Side Storage- *Fourth Floor Supdt Engineer Cabin Table:Table Top - 25Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. Understructure – Legs Made Of 25Mm Thick Pre Lam-Particle Board And Modesty & Side Credenza Made Of 18Mm Thick Pre Lam-Particle Board With Pvc Edge Binding.*Fourth Floor Supdt Engineer Cabin Table:A) Table Size: 2100Mm L X 120Mm D X 750Mm Ht.Side Table Cum Storage: 900Mm L X 450Mm D X 750Mm Ht. (Drawer And Open Storage) , *Fourth Floor Asst-Executive Engr 1&2 & Exe-Engr 1&2 Cabin Table:B)Table Size: 1800Mm L X 1200Mm D X 750Mm Ht. Side Table Cum Storage: 900Mm L X 450Mm D X 750Mm Ht. (Drawer And Open Storage) , *Fouth Floor Asst-Engr 3,4&5 Cabin Table:D) Table Size: 1800Mm L X 71200Mm D X 750Mm Ht. Side Table Cum Storage: 900Mm L X 450Mm D X 750Mm Ht. (Drawer And Open Storage) , *Fouth Floor Hd-1 & Hd-2 Cabin Table:E) Table Size: 1600Mm L X 750Mm D X 750Mm Ht. Side Table Cum Storage: 900Mm L X 450Mm D X 750Mm Ht. (Drawer And Open Storage) , Pedestal With Single Drawer And Shutter ( For Workstations)Size : 400Mm L X 450Mm D X 650Mm Ht. Made Of 18 Mm Thick Pre Laminated Particle Board With Telescopic Drawer Runners , Handle And Individual Lock. , 3Door Storage -Size: 1200Mm L X 400Mm D X 1200Mm Ht.Made Of 18Mm Thick Pre Laminated Board With Pvc Edge Binding, With Multipurpose Lock, D Handle And Box Hinges With Necessary Intermediate Vertical Supports Where Ever Necessary To Avoid Shelf Bending Iss , Storage Size : 1500Mm L X 450Mm D X 750Mm Ht.Made Of 18 Mm Thick Pre Laminated Board With Pvc Edge Binding, With Multipurpose Lock, D Handle And Box Hinges , Conference Hall &Union Office Table With 02 Nos Of Pop Up Box ( 8 Module Without Switch &Socket)Size : 4800Mm L X 1200Mm D X 750Mm Ht. (2 Pieces Of 2400Mm Joined Together)* Table Top - Made Of 16Mm 710 Grade Plywood Finished With 1Mm Laminate (Wooden Suede) Edges In Double Thick Finished With 2Mm Thick Pvc Edge Binding Matching With The Laminate Shade.* Understructure – Box Type Legs Made Of 16 Mm 710 Grade Plywood Finished With 1Mm Laminate (Wooden Suede) , Town Planning Dept & Engineerind Dept. Atndr & Printer Counter Tabletable Size : 2000Mm L X 600Mm D X 750Mm Ht. A)Table Top - 25Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. B)Understructure – Legs Made Of 25Mm Thick Pre Lam-Particle Board And Modesty & Side Credenza Made Of 18Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. , Dinning Room Table Table Size : 1650Mm L X 700Mm D X 750Mm Ht. A)Table Top - 25Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. B)Understructure – Legs Made Of 25Mm Thick Pre Lam-Particle Board And Modesty & Side Credenza Made Of 18Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. , Ee-Additional Secretaryroom:Supplying And Placing In Position Main Table,Eru & Pedestal Of The Following Specifications. 2100X2250x750 Primary Work Surface Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top Soft Closing Access Flap With In-Build Power Box Are Provided On Work Surface For Wire Management Secondary Work Surface Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top. Modesty Panel Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top. Under Structure Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Integrated Pedestal Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Drawer Fronts Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top Pedestal Construction Is Box-Box-File Type Which Uses Powder Coated 400 Mm Long Metal Panel Drawer Slides. Drawer Extension Is 325 Mm. Drawers Have A Soft Closing & Anti Slam Mechanism. Handles Are Provided For Ease Of Opening. Pedestals Are Provided With Lock For Security. , Supplying And Placing In Position Main Table,Eru & Pedestal Of The Following Specifications. 2100X2250x750 Primary Work Surface Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top Soft Closing Access Flap With In-Build Power Box Are Provided On Work Surface For Wire Management Secondary Work Surface Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top. Modesty Panel Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top. Under Structure Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Integrated Pedestal Made Of 25Mm Thick Pre-Laminated Twin Board Of E1-P2 Grade And Approved Shade Confirming To Is-12823:1990, Edge Banded With Matching 2 Mm Thick Pvc Lipping. Drawer Fronts Made Of 25Mm Thick Mdf One Side Pre-Laminate Board Confirming To Is-14587:1998 With 0.4Mm Pvc Membrane Pressed On To Top Pedestal Construction Is Box-Box-File Type Which Uses Powder Coated 400 Mm Long Metal Panel Drawer Slides. Drawer Extension Is 325 Mm. Drawers Have A Soft Closing & Anti Slam Mechanism. Handles Are Provided For Ease Of Opening. Pedestals Are Provided With Lock For Security. , Providing And Supplying Of Encardo 3Str Dimensions W X H X D (Cm) - 179 X 85 X 83.5 Finish Color - Cappuccino Net Weight (Kg) - 85 Primary Material - Solid Wood Upholstery Material - Leatherette Seat Height (Cm) - 55 Warranty - 1 Year Style - Contemporary & Modern Delivery Condition - Knock Down , Providing And Supplying Of Encardo 2Str Dimensions W X H X D (Cm) - 125 X 85 X 83.5 Thickness Of Plywood Used(Mm) : 12 Mm Leg Material: * Material Of Leg : (Plastic / Insert Moulding / Wooden/ Ms + Chrome Plating / Ss) :-Wooden Hanlde Is The Leg Frame Material (Tropical Wood / Pine Wood/ Rubber Wood): Pine Wood Seat Height (Cm) - 47 Warranty - 1 Year , Exicutive High Backrevolving Chairproviding & Laying Revolving Chair With Arm Rest. The Seat And Back Cushion Of The Chairs Should Be Pressed On 12Mm Hot Press Moulded Ply The Seat Cushion Of The Chair Should Be Made Up Of 50Mm Thick High Density Of 45±2 Kg/M3 Polyurethane Mould And Back Cushion Should Be Made Up Of 38Mm Thick High Density 33±2 Kg/M3. The Polyurethane Foam Shall Be As Per Manufacturer’S Specification. The Hardness Of Foam Shall Be 20 Kg On Hampden Machine And 25% Compression And It Should Be Covered With Fabric As Per Manufacturer’S Shade Card .The Arms Of The Chairs Should Be Black. The Gas Lift Mechanism Should Be Tested As Per Bifma X 05.01.2002 Standards .The Pedestal Should Be Five Legged Injection Moulded In Black 30% Glass –Filled Nylon And Fitted With 5 Nos Twin Wheel Castors. The Castors Of The Chairs Should Be Glass Filled, Twin Wheel Castors Confirming To Bifma Standards X 05.01.2002 Tested To Perform 1,00,000 Cycles With 225 Lbs Load. It Should Have Synchro Single Point Locking Arrangement. (Note -The Back And Base Of Chair Should Be Supplied With Fabric Upholstered ) Overall Height Of Chair Should Be Minimum 970 Mm ( Inclusive Of Maximum Adjustment Of Gas Lift And Multifunctional Mechanism ) , Mid Back Office Chair.Providing & Laying Revolving Chair With Arm Rest. The Seat And Back Cushion Of The Chairs Should Be Pressed On 12Mm Hot Press Moulded Ply The Seat Cushion Of The Chair Should Be Made Up Of 50Mm Thick High Density Of 45±2 Kg/M3 Polyurethane Mould And Back Cushion Should Be Made Up Of 38Mm Thick High Density 33±2 Kg/M3. The Polyurethane Foam Shall Be As Per Manufacturer’S Specification. The Hardness Of Foam Shall Be 20 Kg On Hampden Machine And 25% Compression And It Should Be Covered With Fabric As Per Manufacturer’S Shade Card .The Arms Of The Chairs Should Be Black. The Gas Lift Mechanism Should Be Tested As Per Bifma X 05.01.2002 Standards .The Pedestal Should Be Five Legged Injection Moulded In Black 30% Glass –Filled Nylon And Fitted With 5 Nos Twin Wheel Castors. The Castors Of The Chairs Should Be Glass Filled, Twin Wheel Castors Confirming To Bifma Standards X 05.01.2002 Tested To Perform 1,00,000 Cycles With 225 Lbs Load. It Should Have Synchro Single Point Locking Arrangement. (Note -The Back And Base Of Chair Should Be Supplied With Fabric Upholstered ) Overall Height Of Chair Should Be Minimum 970 Mm ( Inclusive Of Maximum Adjustment Of Gas Lift Mechanism ) , Visitor Chair - Model Smat Cantilever The Seat And Back Are Made Up Of 1.2 Cm Thick Hot Pressed Plywood, Upholstered With Fabric And Moulded Polyurethane Foam With Pvc Lipping All Around. The Back Foam Is Designed With Contoured Lumbar Support For Extra Comfort. Back Size: 49.0Cm.(W) X 47.0Cm.(H) Seat Size: 49.0Cm.(W) X 44.0Cm.(D). Polyurethane Foam: The Polyurethane Foam Is Moulded With Density = 45 +/-2 Kg/M3 And Hardness = 20 +/- 2 On Hampden Machine At 25% Compression. Tubular Frame: The Tubular Frame Is Cantilever Type & Made Of Dia.2.54Cm.(1”)X 14 Bg M.S. E.R.W. Tube And Black Powder Coated. , Providing, Supplying And Placing Of Waiting Chair. Seat Shell :The Seat Shell Should Bea Welded Assembly Of Seat,Back And Side Frame. The Seat And Back Should Bemade Of 0.12±0.013Cm Thk Cr Steel Sheet With Oblong Perforations.They Should Bewelded To Sideframe Of Size 3.2±0.05Cm X 0.5 ± 0.05 Cm Thk Hr Steel.The Welded Assembly Should Bepowder Coated ( Dft 40-60 Microns ). , Providing, Supplying And Placing Of Mid Back Chair. Seat/Back Assembly : The Cushioned Seat Should Be Made Of Injection Molded Plastic Outer & Inner. Plastic Inner Should Be Upholstered With Leatherette And Moulded High Resilience (Hr) Polyurethane Foam Of Density 45±2 Kg/M3,And Hardness Load 16 ± 2 Kgf As Per Is:7888 For 25% Compression. The Cushioned Back Should Be Made Of Pu Foam With Insitu Molded Ms E.R.W Round Tube Of Size 1.9±0.03Cm X 0.16 ±0.0128Cm. It Upholstered With Leatherette. , Providing, Supplying And Placing Of Boltless Shelving System Of Height 2100Mm, Length 1300Mm & Depth 500Mm With 6 Panels. Upright Is Roll-Formed Construction Made Up Of Single Piece Having Slots At 25Mm Pitch Upright Typeupright G50 Profile Width 50 Mm Profile Depth 37 Mm No Of Pieces Single Panel Adjustability 25 Mm Material Quality Min Ys=210 Mpa Mfg Process Roll Forming Finish Powder Coated Colour Oxford Blue Bracingis Formed Single Piece Section Which Connects Two Vertical Uprights & Makes A Frame , Modular Workstation With Side Storage And With Sharing Partition*Second Floor Audit Dpt, Accounts, Pd/General Section & Legal Cell Workstation:Partition Size: 1500/1500 Mm L X 50Mm D X 1050Mm Ht. (T Type) Table Size: 1500Mm L X 600Mm D X 750Mm Ht. A) Frame Is Made Up Of 50Mm Powder Coated Ms Sections With Necessary Slotting For Wiring Throughout The Height And The Width Of The Partition. It Also Consists Of Two Race Ways One At The Floor Level For Networking And Another Below The Table Top For Fixing Electrical Plug Points. Frame Will Be Covered With Elegant Powder Coated Aluminium Top & Side Trim.B) Tiles Are Made Up Of 9 Mm Mdf Boards (Fabric/Laminated Finish) And Are Fixed To The Framework Which Also Includes A Writing Board /Pin Up Board For Each Workstation.C) Worktop Made Up Of 25 Mm Pre-Laminated Particle Board With Pvc Edge Binding With Vertical Supports With 25Mm Thick Prelaminated Particle Board.D) Side Storage Top With 25Mm Thick Plb And The Rest Made Of 18Mm Thick Pre Laminated Particle Board With 2 Drawers On Top Withtelescopic Sliders, Handle And Individual Lock And Open Storage Below , Modular Workstation With Side Storage And With L Type Partition *Second Floor Accounts, Pd/General Section & Legal Cell Workstation:Partition Size: A) 1500/1500Mm L X 50Mm D X 1050Mm Ht. (L Type)Table Size: 1500Mm L X 600Mm D X 750Mm Ht. A) Frame Is Made Up Of 50Mm Powder Coated Ms Sections With Necessary Slotting For Wiring Throughout The Height And The Width Of The Partition. It Also Consists Of Two Race Ways One At The Floor Level For Networking And Another Below The Table Top For Fixing Electrical Plug Points. Frame Will Be Covered With Elegant Powder Coated Aluminium Top & Side Trim.B) Tiles Are Made Up Of 9 Mm Mdf Boards (Fabric/Laminated Finish) And Are Fixed To The Framework Which Also Includes A Writing Board /Pin Up Board For Each Workstation.C) Worktop Made Up Of 25 Mm Pre-Laminated Particle Board With Pvc Edge Binding With Vertical Supports With 25Mm Thick Prelaminated Particle Board.D) Side Storage Top With 25Mm Thick Plb And The Rest Made Of 18Mm Thick Pre Laminated Particle Board With 2 Drawers On Top Withtelescopic Sliders, Handle And Individual Lock And Open Storage Below , Superintendent Table & Vehicle Cell Cabin Table With Side Storage Fifth Floor Superindent & Vehicle Cabin Table: Table Size : 1500Mm L X 750Mm D X 750Mm Ht. Side Storage Size : 900Mm L X 450Mm D X 750Mm Ht. * Table Top - 25Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. * Understructure – Legs Made Of 25Mm Thick Pre Lam-Particle Board And Modesty & Side Credenza Made Of 18Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. , Cabin Table With Side Storage Table Top - 25Mm Thick Pre Lam-Particle Board With Pvc Edge Binding.Understructure – Legs Made Of 25Mm Thick Pre Lam-Particle Board And Modesty & Side Credenza Made Of 18Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. *Fifth Floor Kudumbasree Meeting Room & Cabin Table:B)Table Size: 1500Mm L X 750Mm D X 750Mm Ht. Side Table Cum Storage: 900Mm L X 450Mm D X 750Mm Ht. (Drawer And Open Storage) , Typing Pool Workstation Table Size: 1500Mm L X 750Mm D X 750Mm Ht. Side Table Cum Storage: 900Mm L X 450Mm D X 750Mm Ht. (Drawer And Open Storage) Table Top - 25Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. Understructure – Legs Made Of 25Mm Thick Pre Lam-Particle Board And Modesty & Side Credenza Made Of 18Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. , Planning Cell Atndr Table Table Size: 2300Mm L X 500Mm D X 750Mm Ht. Table Top - 25Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. Understructure – Legs Made Of 25Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. , Pedestal With Single Drawer And Shutter ( For Workstations) Size : 400Mm L X 450Mm D X 650Mm Ht.Made Of 18 Mm Thick Pre Laminated Particle Board With Telescopic Drawer Runners , Handle And Individual Lock. , 3Door Storage -Size: 1200Mm L X 400Mm D X 1200Mm Ht.Made Of 18Mm Thick Pre Laminated Board With Pvc Edge Binding, With Multipurpose Lock, D Handle And Box Hinges With Necessary Intermediate Vertical Supports Where Ever Necessary To Avoid Shelf Bending Iss , Storage Size : 1500Mm L X 450Mm D X 750Mm Ht.Made Of 18 Mm Thick Pre Laminated Board With Pvc Edge Binding, With Multipurpose Lock, D Handle And Box Hinges , Conference Table With 02 Nos Of Pop Up Box ( 8 Module Without Switch &Socket)Size : 4800Mm L X 1200Mm D X 750Mm Ht. (2 Pieces Of 2400Mm Joined Together) * Table Top - Made Of 16Mm 710 Grade Plywood Finished With 1Mm Laminate (Wooden Suede) Edges In Double , Dinning Room Table Tablesize : 700Mm L X 700Mm D X 750Mm Ht.. ) Table Top - 25Mm Thick Pre-Lam-Particle Board With Pvc Edge Binding. B)Understructure - Box Type Legs Made Of 25Mm Thick Pre Lam-Particle Board And Modesty & Side Credenza Made Of 18Mm Thick Pre Lam-Particle Board With Pvc Edge Binding. , Providing, Supplying And Placing Of Waiting Chair. Seat Shell :The Seat Shell Should Bea Welded Assembly Of Seat,Back And Side Frame. The Seat And Back Should Bemade Of 0.12±0.013Cm Thk Cr Steel Sheet With Oblong Perforations.They Should Bewelded To Sideframe Of Size 3.2±0.05Cm X 0.5 ± 0.05 Cm Thk Hr Steel.The Welded Assembly Should Bepowder Coated ( Dft 40-60 Microns ). The Seat Has A Front Water Fall Edge To Provide Popliteal Clearance For Comfortable Seating. It Also Has A Buttock Support Curve That Not Only Provides Rear Support But Also Prevents Small Children From Falling Through The Gap Between Seat And Back. Clean And Flat Surfaces Of Seat And Back Aids In Easy Maintenance. * Seat Size : 47.8 Cm (W) X 44.6 Cm (D) * Back Size : 41.6 Cm (W) X 23.0 Cm (H)Understructure Assembly Consshould Be Ts Of Connecting Beam And Leg Assembly Made Of M.S. E.R.W. Oblong Tube Of Size 7.5±0.03Cm X 2.5±0.03Cm X 0.2±0.016Cm Thk.The Welded Structure Assembly Should Bepowder Coated ( Dft 40-60 Microns ).The Leg Assembly Should Befitted With Shoes And Levellers In Nylon. The Leg Structure Should Bedesigned With Minimal Should Be A Of Contact Close To Ground Providing Easy Access For Cleaning Purposes. The Shoes Fitted To Leg Assembly Help In Aligning The Structure For Back To Back Arrangements. Levellers Take Cshould Beof Uneven Flooring.Connecting Beam Should Befitted With Snap Locking End Cap.Lt Also Aids In Side-By-Side Understructure Alignment . Armrest Assembly Consshould Be Ts Of Armrest Frame And Armrest Pad . The Armrest Frame Should Bemade Up Of Size 3.175±0.05Cm X 0.47±0.027Cm Thk Hr Steel And It Should Bepowder Coated ( Dft 40-60 Microns ). Armrest Pad Should Beinjection Molded In Nylon And Should Befitted Onto The Armrest Frame. Overall Dimensions Of Chair Seat Height - 44.1 Cm. Height - 78.5 Cm. Width & Depth Of Chair As- Width-169.5Cm And Depth-63.8 Cm. , Mid Back Office Chair.Providing & Laying Revolving Chair With Arm Rest. The Seat And Back Cushion Of The Chairs Should Be Pressed On 12Mm Hot Press Moulded Ply The Seat Cushion Of The Chair Should Be Made Up Of 50Mm Thick High Density Of 45±2 Kg/M3 Polyurethane Mould And Back Cushion Should Be Made Up Of 38Mm Thick High Density 33±2 Kg/M3. The Polyurethane Foam Shall Be As Per Manufacturer’S Specification. The Hardness Of Foam Shall Be 20 Kg On Hampden Machine And 25% Compression And It Should Be Covered With Fabric As Per Manufacturer’S Shade Card .The Arms Of The Chairs Should Be Black. The Gas Lift Mechanism Should Be Tested As Per Bifma X 05.01.2002 Standards .The Pedestal Should Be Five Legged Injection Moulded In Black 30% Glass –Filled Nylon And Fitted With 5 Nos Twin Wheel Castors. The Castors Of The Chairs Should Be Glass Filled, Twin Wheel Castors Confirming To Bifma Standards X 05.01.2002 Tested To Perform 1,00,000 Cycles With 225 Lbs Load. It Should Have Synchro Single Point Locking Arrangement. (Note -The Back And Base Of Chair Should Be Supplied With Fabric Upholstered ) Overall Height Of Chair Should Be Minimum 970 Mm ( Inclusive Of Maximum Adjustment Of Gas Lift Mechanism ) , Visitor Chair - Model Smat Cantilever The Seat And Back Are Made Up Of 1.2 Cm Thick Hot Pressed Plywood, Upholstered With Fabric And Moulded Polyurethane Foam With Pvc Lipping All Around. The Back Foam Is Designed With Contoured Lumbar Support For Extra Comfort. Back Size: 49.0Cm.(W) X 47.0Cm.(H) Seat Size: 49.0Cm.(W) X 44.0Cm.(D). Polyurethane Foam: The Polyurethane Foam Is Moulded With Density = 45 +/-2 Kg/M3 And Hardness = 20 +/- 2 On Hampden Machine At 25% Compression. Tubular Frame: The Tubular Frame Is Cantilever Type & Made Of Dia.2.54Cm.(1”)X 14 Bg M.S. E.R.W. Tube And Black Powder Coated.
