Tender For Establishment Of Open Gymnasium At Various Places Under Tourism Department - Supply And Installation Of Outdoor Gym Equipment, Thiruvananthapuram-Kerala

Establishment Of Open Gymnasium At Various Places Under Tourism Department - Supply And Installation Of Outdoor Gym Equipment Supply And Installation Of Outdoor Gym Equipment , Supply & Installation Of Outdoor Gym Equipments , Od91983/2023_2024 : Air Walker - Supply And Installation Of Air Walker Having The Following Specifications: Dimensions: (L X W X H) 1190 X 380 X 1244 Mm. Main Frame- Ø 88 Mm Od “B” Class Gi Pipe Dually Bending Design. Foundation Plate –M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Paddle– Ø 42 Mm Od Round Gi Pipe. Handle – Ø 33 Mm Od “B” Class Gi Pipe. Footrest - Cast Iron 124 X 296 X 5 Mm Thick And M.S. Plate Of 2 Mm Thick Use To Support It. Top Closing Cap – Dome Shape Made By Pp / Nylon / Hdpe Material. Closing Cap’S - Pp / Nylon / Hdpe Material. Bracket - 8 Mm Thick Laser Profile Is Use To Support Paddle Frame. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Bearing- Use Is 6005 Permanent Lubricated Reputed Brands. Pin’S – Ø 25Mm M.S. Bright Bar Pin. Circlips– A 24 Circlips Are Used For Assembly. Bearing Bushes -Ø 60 Mm Od Seamless Pipe. Coating - Best Quality Of Powder Coating 80-120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. (Should Be Ce Certified For General Product Safety Directive En-16630 & Din En 16630:2015 Safety Requirement & Test Methods Permanently Installed Outdoor Fitness Equipment) , Od91984/2023_2024 : Chest Press (Double) - Supply And Installation Of Double Chest Press Having The Following Specifications: Dimensions: (L X W X H) 1955 X 710 X 1900 Mm. Main Center Pipe - Ø 114 Mm Od “B” Class Gi Pipe. Foundation Plate –M.S. Round Plate Of Ø 250Mm & 8 Mm Thick. Foundations Cover Cap- Dome Shape Of Pp / Nylon / Hdpe Material. Remaining Frame - Made Up Of Ø 48 Mm Od “B” Class G.I. Pipe. Handle - Made Up Of Ø48mm Od “B” Class G.I. Pipe. Link - Made Up Of Ø 48 Mm Od “B” Class G.I. Pipe. Seat & Back Rest – 380 X 275 X 60 Mm Thick High-Density Polyethylene (Hdpe) Blow Molded With M10 In-Sert Wall Thickness 3 To 4 Mm. Bearing Bush Closing Cap’S– Pp / Nylon / Hdpe Material. Handle Must Be Connected With Frame By 8 Mm Laser Cutting Ms Profile. Top Closing Cap – Dome Shape Made By Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Bearing - Use Is 6005 Permanent Lubricated Reputed Brands. Pin – Made Up Of Ø 25 Mm M.S. Bright Bar Pin. Bearing Bushes - Ø 60 Mm Od Seamless Pipe. Grips - High Quality Rubber Ø 46 Mm Od. Circlips–A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 80-120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. (Should Be Ce Certified For General Product Safety Directive En-16630 & Din En 16630:2015 Safety Requirement & Test Methods Permanently Installed Outdoor Fitness Equipment) , Od91985/2023_2024 : Triple Twister - Supply And Installation Of Triple Twister (Standing Position - 2 And Seating Position - 1) Having The Following Specifications: Dimensions: (L X W X H) 1500 X 1500 X 1420 Mm. Main Frame – Ø 114 Mm Od “B” Class Gi Pipe. Foundation Plate – M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Seat Plate Support – Ø 60 Mm Od “B” Class G.I Pipe. Seating Ring - Ø 33 Mm Od “B” Class G.I Pipe Made By Rolling. Seating Ring Support - Ø 33 Mm Od “B” Class G.I Pipe. Remaining Frame – Is Made By 100 X 50 X 2.5 Mm Rectangular Pipe. Standing Plate- Ø 300 Mm Od X 10 Mm Thick M.S. Plate. Seating Plate- Ø 300 Mm Od X 10 Mm Thick M.S. Plate. Seating Seat Position And Other Two Standing Position Plates Are Fixed 120 Degrees Each From Other. Handle – Ø 33 Mm “B” Class G.I. Pipe Made By Rolling. Top Closing Cap – Dome Shape Made By Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Bearing - Used Is 6005 Permanent Lubricated Reputed Brand. Bearing Bushes - Ø 60 Mm Od Seamless Pipe. Pin – Made Up Of Ø 25Mm M.S. Bright Bar. Circlips– A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 80 -120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing (Should Be Ce Certified For General Product Safety Directive En-16630 & Din En 16630:2015 Safety Requirement & Test Methods Permanently Installed Outdoor Fitness Equipment) , Od91986/2023_2024 : Leg Press (Double) -Supply And Installation Of Double Leg Press Having The Following Specifications: Dimensions: (L X W X H) = 1676 X 400 X1500 Mm. Main Frame - Ø 114 Mm Od “B” Class Gi Pipe. Foundation Plate – M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Foundations Cover Cap - Dome Shape Of Pp / Nylon / Hdpe Material. Link - Is Ø 60 Mm Od “B” Class Gi Pipe. Seat Frame - Ø 42 Mm Od “B” Class Gi Pipe. Leg Press Back Rest Should Be Angled In 120 -130 Degree. Foot Rest - Cast Iron 124 X 296 X 5 Mm Thick And M.S Plate Of 2 Mm Thick Use To Support It. Seat & Back Rest – 380 X 275 X 60 Mm Thick High-Density Polyethylene (Hdpe) Blow Molded With M10 In-Sert Wall Thickness 3 To 4 Mm. Link Connected With Frame By 8 Mm Thick Laser Cutting Ms Profile. Top Closing Cap – Dome Shape Made By Pp / Nylon / Hdpe Material. Closing Cap’S- Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded At Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Bearing- Use Is 6005 Permanent Lubricated Reputed Brand. Pin– Ø 25 Mm M.S. Bright Bar Pin. Bearing Bushes - Ø 60 Mm Od Seamless Pipe. Circlip– A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 80 -120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing (Should Be Ce Certified For General Product Safety Directive En-16630 & Din En 16630:2015 Safety Requirement & Test Methods Permanently Installed Outdoor Fitness Equipment) , Od91987/2023_2024 : Rower - Supply And Installation Of Rower Having The Following Specifications: Dimensions: (L X W X H) = 1472 X 915 X 1040 Mm. Upper And Bottom Pipes - Ø 88 Mm Od “B” Class Gi Pipe. Foundation Plate –M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Handle - Ø 33 Mm Od “B” Class G.I Pipe. Angle Between Handle And Horizontal Surface Is 75 - 80 Degree. Linkages – Ø 48 Mm Od “B” Class G.I. Pipe. Seat & Back Rest – 380 X 275 X 60Mm Thick High-Density Polyethylene (Hdpe) Blow Molded With M10 In-Sert Wall Thickness 3 To 4 Mm. Foot Resting Pipe - Ø 60 Mm Od “B” Class G.I. Pipe. End Closing Cap – Dome Shape Made By Pp / Nylon / Hdpe Material. Closing Caps – Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø250 Mm & 8Mm Thickness Is Welded At Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Pin – Ø 25 Mm M.S. Bright Bar Pin. Circlips– A 24 Circlips Are Used For Assembly. Bearing Bushes - Ø 60 Mm Od Seamless Pipe / Bar. Bearing- Use Is 6005 Permanent Lubricated Reputed Brands. Grips – High Quality Rubber 46 Mm Od. Coating - Best Quality Of Powder Coating 80 -120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing (Should Be Ce Certified For General Product Safety Directive En-16630 & Din En 16630:2015 Safety Requirement & Test Methods Permanently Installed Outdoor Fitness Equipment) , Od91988/2023_2024 : Shoulder Builder (Double) - Supply And Installation Of Double Shoulder Builder Having The Following Specifications: Dimensions: (L X W X H) 890 X 558 X 1500 Mm. Main Frame - Made From Ø 114 Mm Od “B” Class G.I. Pipe. Foundation Plate –M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Foundation Cover Cap - Dome Shape Of Pp / Nylon / Hdpe Material. Shoulder Ring Pipe - Ø 33 Mm Od “B” Class G.I Pipe. Shoulder Ring Pipe Support – Ø 25 Mm Od “B” Class G.I Pipe. Nylon Knob With Bearing – Is Fixed On Shoulder Ring Pipe For Rotating Purpose (2 Set To Be Fixed In A Position For Kids And Adults). Top Closing Cap’S- Pp / Nylon / Hdpe Material. Closing Cap – Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded At Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Bearing - Use Is 6005 Permanent Lubricated Reputed Brands. Pin – Ø 25 Mm M.S. Bright Bar Pin. Foundation Plate – M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick.<Br>Bearing Bushes - Ø 60 Mm Od Seamless Pipe. Circlips – A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 80 -120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. (Should Be Ce Certified For General Product Safety Directive En-16630 & Din En 16630:2015 Safety Requirement & Test Methods Permanently Installed Outdoor Fitness Equipment) , Od91989/2023_2024 : Sit-Up Board - Supply And Installation Of Sit-Up Board Having The Following Specifications: Dimensions: (L X W X H) 1570 X 450 X 660 Mm. Main Frame - Made From Ø 33 Od “B” Class G.I. Pipe Bending Design. Foundation Plate – M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Leg Support - Ø 60 Mm Od “B” Class G.I Pipe. Remaining Frame - Ø 60 Mm Od “B” Class Gi Pipe And 100 X 50 Ms Pipe. Backrest Seat - Made Of M.S Checkered Plate Sheet Of 3 Mm Thickness Size 1100 Mm X 310 Mm. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Coating - Best Quality Of Powder Coating 80 -120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. (Should Be Ce Certified For General Product Safety Directive En-16630 & Din En 16630:2015 Safety Requirement & Test Methods Permanently Installed Outdoor Fitness Equipment) , Od91990/2023_2024 : Sky Walker - Supply And Installation Of Sky Walker Having The Following Specifications: Dimensions: (L X W X H) 1720 X 910 X 1700 Mm. Main Frame - Made Of Ø 88 Mm Od “B” Class Gi Pipe Dually Bending Design. Foundation Plate – M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Paddle Vertical Support - Ø 42 Mm Od “B” Class Gi Pipe. Handle - Ø 33 Mm Od “B” Class Gi Pipe Dually Bending Design. Leg Movement Frame – 50 Mm X 50 Mm X 2 Mm Thick Square Pipe. Footrest - Cast Iron 124 X 296 X 5 Mm Thick And M.S. Plate Of 2 Mm Thick Use For To Support It. Top Closing Cap – Dome Shape Made By Pp / Nylon / Hdpe Material. Closing Cap’S– Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm M.S Pipe. And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Grips - High Quality Rubber Ø 46 Mm Od. Bearinguse Is 6005 Permanent Lubricated Reputed Brand. Bearing Bushes - Ø 60 Mm Od Seamless Pipe. Pin –Made Of Ø 25Mm M.S. Bright Bar. Circlips – A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 80-120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. (Should Be Ce Certified For General Product Safety Directive En-16630 & Din En 16630:2015 Safety Requirement & Test Methods Permanently Installed Outdoor Fitness Equipment) , Od91991/2023_2024 : Surfboard - Supply And Installation Of Surfboard Having The Following Dimensions: (L X W X H) 1090 X 890 X 1390 Mm. Main Frame – Made From Two Pipes Of Ø 114 Mm Od “B” Class Gi Pipe. Foundation Plate –M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Connecting Pipe - Ø 88 Mm Od “B” Class Gi Pipe Is Used To Connect Both Main Frame Pipes At Top End And Ø 42 Mm Pipe Is Used To Connect At Bottom End. Handle - Ø 42 Mm And Ø 33 Mm Od “B” Class Gi Pipe. Support Pipe – Ø 60 Mm Must Be Used To Support Leg Movement Frame. Leg Movement Frame– Ø 42Mm Od “B” Class Gi Pipe. Footrest - Cast Iron 325 X 270 X 8 Mm Thick And M.S. Plate Of 250 X 200 X 2 Mm Thick Use For To Support It. Bracket - 8Mm Thick Laser Profile Is Use To Support Leg Movement Frame. Top Closing Cap – Dome Shape Made By Pp / Nylon / Hdpe Material. Closing Cap’S– Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded At Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Grips - High Quality Rubber Ø 46Mm Od. Bearing - Use Is 6005 Permanent Lubricated Reputed Brand. Bearing Bushes - Ø 60 Mm Od Seamless Pipe. Pin – Made Of Ø 25Mm M.S. Bright Bar. Circlips – A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 80 -120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. (Should Be Ce Certified For General Product Safety Directive En-16630 & Din En 16630:2015 Safety Requirement & Test Methods Permanently Installed Outdoor Fitness Equipment) , Od91992/2023_2024 : Cross Trainer (Double) - Supply And Installation Of Double Cross Trainer Having The Following Specifications: Dimensions: (L X W X H) 2280 X 550 X 1650 Mm. Main Frame- Made Of Ø 88 Mm Od “B” Class Gi Pipe Dually Bending Design. Foundation Plate – M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Paddle Vertical Support - Ø 42 Mm Od “B” Class Gi Pipe. Handle - Ø 33 Mm Od “B” Class Gi Pipe Dually Bending Design. Leg Movement Frame – 50 Mm X 50 Mm X 2 Mm Thick Square Pipe. Footrest - Cast Iron 124 X 296 X 5 Mm Thick And M.S. Plate Of 2 Mm Thick Use For To Support It. Top Closing Cap – Dome Shape Made By Pp / Nylon / Hdpe Material. Closing Cap’S– Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od B Class G.I. Pipe. And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Grips - High Quality Rubber. Bearing- Use Is 6005 Permanent Lubricated Reputed Brand. Bearing Bushes - Ø 60Mm Od Seamless Pipe. Pin –Made Of Ø 25Mm M.S. Bright Bar. Circlips – A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 80-100 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing (Should Be Ce Certified For General Product Safety Directive En-16630 & Din En 16630:2015 Safety Requirement & Test Methods Permanently Installed Outdoor Fitness Equipment) , Od91993/2023_2024 : Back Extension - Supply And Installation Of Back Extension Having The Following Specifications: Dimensions: (L X W X H) 1060 X 730 X 990 Mm. Main Frame - Made From Ø 88 Mm Od “B” Class G.I. Pipe. Foundation Plate – M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Leg Support - Ø 42 Mm Od “B” G.I Pipe. Seat Rest Pipe – Ø 42 Mm Od “B” Class G.I Pipe. Handle Pipe – Ø 33 Mm Od “B” Class G.I Pipe. Footrest - Cast Iron 124 X 296 X 5 Mm Thick And M.S Plate Of 3 Mm Thick Used To Support It. Footrest Pipe – Ø 42 Mm Od “B” Class G.I Pipe And 80 X 40 Mm Ms Rectangular Pipe. Closing Cap – Pp / Nylon / Hdpe Material. Seat – 360 X 300 X 2 Mm Thick M.S. Seat With Corner Fillet For Safety. Grips - High Quality Rubber Ø 46 Mm Od. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Coating - Best Quality Of Powder Coating 80-120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing.. (Should Be Ce Certified For General Product Safety Directive En-16630 & Din En 16630:2015 Safety Requirement & Test Methods Permanently Installed Outdoor Fitness Equipment) , Od91994/2023_2024 : Push-Up Bar And Dip Station - Supply And Installation Of Push-Up Bar And Dip Station Having The Following Specifications: Providing And Fixing Push Up Bar Made From G.I. Pipe. Dimensions: (L X W X H) 1220 X 530 X 1500 Mm. Main Frame - Ø 88 Mm Od “B” Class Gi Pipe. Leg & Hand Support - Ø 33 Mm Od “B” Class Gi Pipe. Foundation Plate – M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Top Closing Cap – Dome Shape Made By Pp / Nylon / Hdpe Material. Closing Cap’S- Plastic Molded. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Coating - Best Quality Of Powder Coating 80 - 120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing (Should Be Ce Certified For General Product Safety Directive En-16630 & Din En 16630:2015 Safety Requirement & Test Methods Permanently Installed Outdoor Fitness Equipment) , Od91995/2023_2024 : Arm And Paddle Bike - Supply And Installation Of Arm And Paddle Bike Having The Following Specifications: Dimensions: (L X W X H) 990 X 500 X 880 Mm. Main Frame –100 Mm X 50 Mm X 2.5 Mm Rectangular Cr Pipe With Bending Design. Foundation Plate – M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Handle – Ø 33 Mm Od “B” Class Gi Round Pipe Dully Bending Design. Side And Top Cover – 1.6 Mm Thick Ms Laser Cutting Profile Is Used. Seat – 380 X 275 X 60 Mm Thick Hdpe Blow Moulding. Paddle –100 Mm X 50 Mm Capsule Pipe And 40 X 16 Mm Ms Flat Should Be Used For Connecting The Paddle And Shaft. Closing Cap’S – Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Bearing Bushes - Ø 60 Mm Od Seamless Pipe. Bearing - Use Is 6005 Permanent Lubricating Sealed Reputed Brand. Shaft -Made Up Of Ø25mm Od Ms Bright Bar. Circlips– A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 80 - 120 Micron. Safety Instructions And Exercise Chart - Start & Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing.. (Should Be Ce Certified For General Product Safety Directive En-16630 & Din En 16630:2015 Safety Requirement & Test Methods Permanently Installed Outdoor Fitness Equipment) , Od91996/2023_2024 : Horse Rider - Supply And Installation Of Horse Rider Having The Following Specifications: Dimensions: (L X W X H) 1140 X 400 X 1400 Mm. Main Frame - Ø 114 Mm Od “B” Class Gi Pipe. Foundation Plate – M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Foundation Cover Cap - Dome Shape Of Pp / Nylon / Hdpe Material. Remaining Frame – Is Made By Ø 48 Mm Od “B” Class Gi Pipe. Seat Frame – Is Made By Ø 48 Mm Od “B” Class Gi Pipe. Seat Position Must Be Horizontal To 110 -120 Degree. Link - Made Up Of Ø 48 Mm Od “B” Class G.I. Pipe. Angle Between Link And Ground Position Is 10-20 Degree. Handle - Ø 33 Mm Od “B” Class Gi Pipe. Paddle Vertical Support - Ø 60 Mm Od “B” Class Gi Pipe. Handle Frame- Ø 42 Mm Od “B” Class Gi Pipe Dually Bending Design. Foot Pipe - Ø 33 Mm Od “B” Class Gi Pipe. Support Frame – 10 Mm Thick Ms Flat Is Used. Seat- Dimension 320 X 270 X 100 Mm Blow Moulded Wall Thickness 4Mm Material Hdpe. Bearing Bush Closing Cap – Pp / Nylon / Hdpe Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded At Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Bearing - Use Is 6005 Permanent Lubricated Reputed Brand. Bearing Bushes - Ø 60Mm Od Seamless Pipe. Pin – Made Of Ø 25 Mm M.S. Bright Bar. Grips - High Quality Rubber Ø 46 Mm Od. Circlips – A 24 Circlips Are Used For Assembly. Coating - Best Quality Of Powder Coating 60 To 70 Micron. Safety Instructions And Exercise Chart - Start &Finish Position Stick On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing (Should Be Ce Certified For General Product Safety Directive En-16630 & Din En 16630:2015 Safety Requirement & Test Methods Permanently Installed Outdoor Fitness Equipment) , Od91997/2023_2024 : Single Bar - Supply And Installation Of Single Bar Having The Following Specifications: Dimensions: (L X W X H) 3550 X 2590 Mm. Main Frame - Made From Ø 48 Mm Od “B” Class G.I. Pipe. Frame Of Single Bar – Ø 33 Mm Od “B” Class G.I. Pipe. Foundation Plate – M.S. Round Plate Of Ø 250 Mm & 8 Mm Thick. Top Closing Cap’S - Decent Design Size Pp / Hdpe / Ms. Material. Foundation Stool: Made From Main Pipe Ø 88 Mm Od M.S Pipe And Top Support Of M.S. Round Plate Of Ø 250 Mm & 8 Mm Thickness Is Welded Top. Square Tube Of 30 X 30 X 2 Mm Must Be Used To Support Center Pipe. Height Of Stool Is 3 Ft. Foundation Stool Is Embedded In C.C. Stock Below Ground Level. Coating - Best Quality Of Powder Coating 80-120 Micron. Safety Instructions And Exercise Chart – Made From Aluminum / Stainless-Steel Stick-On Product. All Joints Must Be Robotic Welded And Zinc Primer Paint Should Be Applied At All The Welding Points Prior To Finishing. (Should Be Ce Certified For General Product Safety Directive En-16630 & Din En 16630:2015 Safety Requirement & Test Methods Permanently Installed Outdoor Fitness Equipment)

INR 2950 /-

INR 50000.0 /-

INR 62.32 Lakhs /-