Tender For Construction Of Top Story To Library Building At Uppidamangalam Town Panchayat, Karur District.; 1 Plain Cement Concrete of mix 1 : 4 : 8 (One Cement four sand eight aggregates) using 40mm gauge hard broken including cost conveyance of all materials to site including formwork and centering labour charges, transporting and placing in position including shoring, strutting, forming protective bunds, cofferdams bailing out of water labour for mixing compacting, finishing and curing, working at depths, tools and plants and incidental charges such as sheeting, shoring and bracing and their subsequent removal etc., complete as per standard specification. 2 Supplying andErrectingsteel centering including necessary supportsfor plain surfaces for Reinforced Cement Concrete works such as Coloumn footing,Coloumn pedestals,plith beams, grade beams,staircase steps,etc which requires only nominal strutting using mild steel sheetsof size 90mm x60mm and 10Bg stiffened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervels etc complete in all floorsComplying with standard Specification without Strutting. ( TNSS NO or NBC No 30(S) 86 86 A V, VI(S3)VII 3 For Plane Surfaces such asRectangular or Square RCC columns, sunshades, top and bottom slab of RCC boxing, etc. 4 For Plane Surfaces such as RCC Floor Slab, Roof Slab, Beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc. 5 R.C.C.1 : 11/2 : 3 (One Cement One and Half Sand Three Aggregates) using 20mm gauge hard Granite broken stone jellyincluding cost curing, etc., complete as per standard specification and as directed by Engineer incharge. 6 Ground Floor 7 Supplying andFabricatingandplacinginpositionmildsteelofribbedforsteelbarsforallR.C.C.worksincludingbending,cranking bindingetc.,includingcostofbindingwireM.S.chairslapstofixthereinforcementinallpositionalllasourandmaterialsetc.CompletecomplyingwithstandardSpecification. 8 Brickworkincementmortor1 : 5(One Cement and Five Sand)usingbest quality of countrybricksof size 83/4x41/4x21/4 includingall costof materialsand Labour Charges including Curing charges etc., Complete as per standard specification. 9 Ground Floor 10 Special CeilingPlasteringinC.M. 1 : 3 (One Cement, Three Sand) to10 mmthickincludingallcostandconveyance ofallmaterialstositeincludingcostofcementwhichwillbepurcharedlocallybythe contractor andconveyanceofthesametotheactualworksiteandcostformworkincludingwatering curingandallleadsofgoodpotablewaterandallother. 11 PlasteringinC.M. 1 : 5to (One Cement, Five Sand) 12 mmthickincludingallcostandconveyanceofallmaterials tositeincludingcostofcementwhichwillbepurcharedlocallybythecontractor and conveyanceofthesametotheactualworksiteandcostformworkincludingwatering curingandallleadsofgoodpotablewaterandallother. 12 Supplying and Painting thewalls with TwoCoatsColour Cement Paint over one coat of cement primer as instructed by the departmrntal officers includingPreparation of surface curing, etc complete in all floorscomplying with standard specification. ( The Colour and shade of the paint shall be got approved by the departmental officers.) 13 Paving the Floor with Descrgned Coloured Vitrified tiles of size 600 x 600 x 8mm of best quality and approved variety complying / confirming ISI specification land over cement mortar 1:3 (one cement and three sand) 20mm thick and pomted with same coloured cement neatly etc., complete. 14 Flooring with Ceramic Tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three Sand)base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification.(The make and brand of the tiles should be got approved by Executive Engineer before use on works) 15 Dadooing walls with following best approved quality, white / colour glazed tiles of following sizes set in Cement Mortar 1:2 (One Cement and Two sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers. 16 Supplying and Fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work. 17 Supplying and Fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work(PWD SOR 2020-2021, P.No 65) 18 SupplyandFixingof Steel Dooors, Windows and Ventilators including allLabourCharges for wroughtandPut upinpositionandalsofixinghold fastsinframesandmasonryetc., Complete Complying with StandardSpecifications. 19 Painting the New Iron Works such as Steel Doors, Windows,Ventilators windows bars,balustrades etc,in all floor withtwo coats of best approved first quality and colour of synthetic enamel paint of approved quality, colour and brand (to be approved by executive engineer before use on works ) over one the existing red oxide priming coat in all floors excluding cost of priming coat etc,complete complying with Standard Specification. ( The Make, Quality and colour of paint should be got approved bythe engineer in charge before use on works )( TNSS NO or NBC No 61 V VI (54) 3) 20 Providing & fixing PVC RAIN WATER DOWNFALL PIPE of the following dia with necessary T.W.Clamps Plugs, Shoes,Bemds, other clamps, screws nails etc.,complete complying with standard specification. The rate is inclusive of cost of removable iron gratings of appropriate size. The size of Teak Wood plugs used is 150X25mm in front & 200x75mm in rear (wall side) with a depth of 110mm. The pipe is to be fixed by means of U clamps at the centre of pipes to be fixed.110mm dia PVC Pipe [4 Kg/SqCm] 21 Supply and Fixing of PVC Solid Doors using 19gauge 19mm MS Sq,tubes for styles and frames, 15mm MS Sq.tubes for to, Lock and bottom rails. The Steel Tubes shall be covered with 5mm thick Solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in positionincluding furniture and fittings. The over all size of styles shall be 50mm X 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm X 30mm. The over all size of frames shall be 50mm X 45mm with suitable tabate for housing the shutter etc, complete as per standard specification. PWD SOR Pg. No. 49 Sl.No.122 a 22 Weathering Course in Brick Jelly and lime concrete using broken brick jelly of size 20 mm uniform gauge in pure slacked lime ( no sand to be used ) the proportion of brick jelly to lime being 32:12.5 by volume laid over the RCC roof slab in a single layer of required design , slope and finished thickness by beating the concrete with wooden and beaters of approved pattern keeping the surface constantly wet by springing lime Jaggery water etc,. complete as per standard specification and as directed by the Engineer incharge 23 Finishing The Top of Roof with One Course of Machine Pressed Tiles of Size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers 24 Plain Cement Concrete of mix 1 : 2: 4 (One Cement Two sandFour Aggregates) using 20mm gauge hard broken including cost conveyance of all materials to site including formwork and centering labour charges, transporting and placing in position including shoring, strutting, forming protective bunds, cofferdams bailing out of water labour for mixing compacting, finishing and curing, working at depths, tools and plants and incidental charges such as sheeting, shoring and bracing and their subsequent removal etc., complete as per standard specification. 25 Supply and Fixing of Stainless Steel (Salem Stainless Steel) Door frame ( Box section using stainless steel plate of 1.6mm thick) of size 100mm X 60mm with a rebate of 30 / 35mm X 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel holdfast etc. 26 Supplying & FixingDoor Shutters for Mediun Density Fiber Board of exterior grade 35 mm thick,single leaf conforming to IS:12406/1989 with 35x12 mm T.W.Lipping on all edges with necessary adhesives and CP screws complying with standard specifications. The rate is inclusive ofthreee coats of best quality varnish but excluding cost of furniture fittings.such as 300 mm tower bolt 2nos,200mm towerbolt I no. 300mm Aldrop 1 No. Alu handle ornamental type 2 Nos,and 1 No. Door stopper etc complete. 27 Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete 28 Earthling as per ISI Specification with an earth electrode of 2.1mt class B GI pipe of dia not less than 40mm and with 20mm dia copper earth flat of size 125mm x50mmx6mm, with funneling arrangement using charcoal, common salt, G.I.reducer, check nuts etc.,and masonry work and providing RCC cover slab 38mm thick for the Brick masonry including cost of steel and fabrication of reinforcement etc., complete in all respects as directed by the departmental officers. (SD 233) 29 Supplying and Run off 8 SWG copper wire on walls or below ground level with necessary U nails, earth work excavation and refilling & including the cost of all materials etc., complete in all respects as directed by the departmental officers.(SD 75) 30 Supplying and Fixing of 3 Phase DB with MCB 12 way TPMCB sheet steel distribution boards (flush type/surface type) fitted with bus bars and neutral links with three phase MCB outgoings and separate 4 way provision for accommodating One No. 4 pile incoming MCB / Isolator and another separate 4 way provision for accommodating One No. 4 pole ELCB / RCD (totally 8 ways in one segment) (3 x 4 ways in each segment) and separate provisions for MCB / Isolator (totally 12 Nos.) for sub incomers in 3 segments with label holder etc.complete in all respects as directed by the departmental officers 31 Supply and Run off 2 of 2.50sqm PVC insulated single core unsheathed copper conductor cable of 1100 V grade with ISI markconfirming to IS:694/1990 with continuousearth connection by means of 1.50 sqm PVC insulated single core unsheathed copper conductor cable confirming to IS:694/1990 in suitable PVC rigid pipe 1.8mm thick concealed in wallfor mains including the cost of PVC pipes and specials, cables, cement, brass screws, T.W plugs, saddles and labour etc., complete in all respects as directed by the departmental officers. (derived from SD 55) 32 Supply and Run off 2 of 1.5 sqmm PVC insulated single core unsheathed copper conductor cable of 1100 V grade with ISI markconfirming to IS:694/1990 with continiousearth connection by means of 1.50 sqm PVC insulated single core unsheathed copper conductor cable confirming to IS:694/1990 in suitable PVC rigid pipe 1.8mm thick concealed in wallfor mains including the cost of PVC pipes and specials, cables, cement, brass screws, T.W plugs, saddles and labour etc., complete in all respects as directed by the departemental officers. (derived from SD 54) 33 Supply and Fixing of TNEB meter Board suitable for 32 A Three phase service connection with 32A fuse unit(500V)32A neutral link and earth link (1 x 1/8 Copper flat) on T.W plank of size 600mm x450mm x 19mm with supportingT.W.reepers of 1 thick oneither sider with painting withsuitable bolt and nuts for fixingthe TW plank on wall withearth connection and interconnection with 7/20 PVCinsulated copper wire from EBmeter to fuse unit. SD 127) 34 Supply and Run of 4 core 16 Sq.mm PVC Armoured cableof 1100 V grade with ISI mark.(PWD SOR PG no 125) 35 Supply and Run of 4 core 10 Sq.mm PVC Armoured cableof 1100 V grade with ISI mark.(PWD SOR PG no 125) 36 Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 3mm thick hylum sheet cover with TW switch box and 5A F.T. switch with continuous earth wire connection of 14 SWG TC wire for making good of the concealed portion with suitable colour for PVC Concelaed light point / Fan point (For Electronic regulator). SD 23 37 Wiring with 2 x 1.5 sqmm (22 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 x 100 x 113 mm TW switch box with 3mm hylum sheet cover for5A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point. SD 38 38 TowardsCostandSupplyofCFL LightFittingsincludingallcostand conveyancetositeetccomplete. 39 Supply and Fixing of 1200mm (48) sweep AC ceiling fan complete with stepped electronic regulator with 300mm down rod on the existing clamp (SD111) 40 Supply and Fixing of 400mm Sweep-wall mount fanincludingallcostand conveyancetositeetccomplete. 41 Supplying and Fixing in position best quality P.V.C soil/ waste pipes (6KSC) of various sizes having ISI mark and providing leakproof joints including fixing to the wall with P.V.C/ M.S clamps etc., and making connection to all sanitaryfittings, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications.(D) 42 Supply and Delivery and Fixing of HDPE tank as per IS 12701 / 1996 including loading,unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc., 43 Supplying and Fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements).The valves to be used on work shall be got approved by the Executive Engineer before use on work. 44 25mm Gun metal Gate Valve 45 40mm Gun metal Gate Valve 46 Supplying and Fixing in Position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary.(Taps should be got approved by the Executive Engineer before use on the works) 47 SD Tap 48 Pillar Tap 49 Supplying, Laying and Jointing PVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications.The PVC pipes shall be got approved by Executive Engineer before use on works. 50 25mm dia 51 32mm dia 52 Supplying PVC Specials (with working pressure 10 kg. / sq.cm.) in water supply arrangements (both in internal and external water supply arrangements includingallcostand conveyancetositeetccomplete. 53 PVC Coupler 54 25mm Pipe coupler 55 32mm Pipe coupler 56 PVC Elbow 57 25mm Pipe elbow 58 32mm Pipe elbow 59 PVC Bend 60 25mm Pipe Bend 61 32mm Pipe Bend 62 PVC Tee 63 25mm Pipe Tee 64 32mm Pipe Tee 65 PVC End Cap 66 25mm Pipe end cap 67 32mm Pipe end cap 68 PVC Reducer 69 25 mm x 20 mm Reducer 70 32 mm x 25 mm Reducer 71 PVC Reducer Tee 72 25 mm x 20 mm Reducer Tee 73 32 mm x 25 mm Reducer Tee 74 PVC Reducer Elbow 75 25 mm x 20 mm Reducer Elbow 76 32 mm x 25 mm Reducer Elbow 77 Jet Nipple 78 25mm Pipe Jet Nipple 79 32mm Pipe Jet Nipple 80 Supplying and Fixing in position 15mm dia C.P.Shower rose & stop cock ofapproved make confirming to IS specifications and quality including cost ofShellac thread etc. complying with standard specification. 81 C.P. Shower Rose 82 Stop Cock 83 Supplying and Fixing in positionC.P. Towel rail 600mm long and 20mm dia with brackets of same materials including cost of teak wood plug and C.P.Screws etc. complete complying with standard specification. 84 Supplying and Fixing in positionC.P. Soap tray of size 150 x 150mm including cost of teak wood plug and C.P. screws. etc. complete complying with standard specification. 85 Supply and Delivery of Electric Monoset centrifugal pump conforming to IS9079:2002 asamended from time to time ,with CIFG200 Casing ,hydraulically and dynamically balanced BronzegradeLTB-2 impeller ,impeller ring and casing ring,stainlesss teel shaft capable of discharging required quantity of water against a total head noted below due to all causes.Pump shall of BEE 3 Star Rated and capable of discharging the specified quantity at the head noted at theminimum NPSHA at sit conditions. The shut off head shall beat least 25% over and above the head at duty point.The pump shall be suitable for operation in A Cthreephase,415V+/-10%,50Hz+/-5%. Squirrel cage induction motor for continuous operation.The speed of the Pump and Motor shall be not less than 2700to2900 RPM respectively.(250x20) TWAD SOR Pg 95 86 Supplying and Fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm P or S trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 liters capacity PVC / 12.5 liters capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings. 87 Supplying and Fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of Sandand five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three Sand ) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)
