Tender For Purchase Of Tata Ac With 1No And Construction Of Resource Recovery Shed In The Resource Recovery Parkin Udayendiram Town Panchayat; 1 Supply and delivery of Light Commercial Vehicle with following Specifications Displacement (CC) / Engine capacity., 700 CC - 1250CC Max Power, 20-30BHP @ 2500 rpm and above, Max Torque, 500NM @ 2000 rpm and above, Type of fuel Diesel, Load Capacity, 2 cu. m, Vehicle emission Norms BS – VI, No of cylinder in engine, 2 - 4 cylinder Length of chassis, 3800 mm - 3950 mm, Width of chassis 1500 mm - 1550 mm, Ground clearance. 150 mm - 165 mm Fuel tank capacity, Diesel - 30 Ltrs to 40 ltrs, NG - 12 -25kg, Size of Tyres & Nos, 145 R 12 - 5Nos, wheel base 1900 mm - 2250 mm, Gross vehicle weight, 1550 kg - 1900 kg, Clutch, Single plate dry friction diaphragm, Transmission System, Manual, No of speed/ forward gears 4 Nos Speeds(4F+ 1R), Type of Steering, Manual / Power Speed Governors, Shall be Fitted, Pay Load 800Kg to 1000Kg Tipper body length 2100 mm-2200mm, Mild steel Tipper body Width 1400 mm -1500mm, l4ild steel Tipper body Height 750mm- 950 mm, Mild steel Side portion (LH&RH)& rear doors Sheet thickness 2 mm, lvl ild steel Tipper body top sheet including frame sheet thickness 1.6mm, Mild steel Tipper Body Top Lid Sheet thickness 1.2mm, Mild steel Tipper Container Tipper Contajner should be Fabricated with two doors on the rear side and four doors on four top corners of the containers with hinges and locking system. A partition should be provided on the middle of container along the vertical lenqth of the body. Tipper Body Top Lid main Sheet thickness 75x40x6mm Hyd rau lic cylinder make Reputed Make Hydraulic system driven Main Engine Pump Make As per IS standard Painting Should be painted with one coat of Anti-corrosive epoxy primer and two coats of enamel paint for approved quality to ensure long lasting resistance for weatherizing and breakage. The color shade should be as per norms. Lettering To be carried out as directed by Dept officers Tipper body rear door Shall be with necessary lockinq facility Side safety guard Shall be provided as per RTO requirement Additional conditions Vehicle with fuel sensor and GPS tracking.Warranty Distance/Year 2500KM/12 months whichever is earlier. 2 Earthworkexcavationin all classes of Soils and Sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering , bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the Departmental officerswith an initial lead of 10mts and initial lift of 2mts and clearing and levelling the site etc, complete complying with standard specification. 3 Supply delivery and filling of Stone Dust in Layer of not more than 15cm thick including watering with all layers and consolidation complying with standard specification including cost and conveyance of sand at site and all labour charges and all other incidential charges etc., complete as per Standard Specification. 4 Cement Concrete of mix 1 : 4 : 8 (One Cement four sand eight aggregates) using 40mm gauge hard broken including cost conveyance of all materials to site including formwork and centering labour charges, transporting and placing in position including shoring, strutting, forming protective bunds, cofferdams bailing out of water labour for mixing compacting, finishing and curing, working at depths, tools and plants and incidental charges such as sheeting, shoring and bracing and their subsequent removal etc., complete as per standard specification. 5 Supplying anderrectingsteel centering including necessary supportsfor plain surfaces for Reinforced Cement Concrete works such as Coloumn footing,Coloumn pedestals,plith beams, grade beams,staircase steps,etc which requires only nominal strutting using mild steel sheetsof size 90mm x60mm and 10Bg stiffened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervels etc complete in all floorsComplying with standard Specification without Strutting. 6 a). Plinth Beam 7 b). Slab, Lintel, Beam, etc., 8 c). Column 9 Providing and laying in position Standardised Concrete Mix M-20 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 325Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of Crushed Stone Sand (M- Sand), but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - 10 a). Below Ground Level 11 Supplying and Fabrication of Steel and placing in position MS / Ribbed tor steel grills for RCC works as per design given including cost of steel and GI binding wire in Floors etc., Complete complying with standard specification in force per Kilogram. 12 Brick Work in Cement Mortar 1:5 Mix (one cement, five sand) using new Country Bricks of size ( 9” x 4 3/8” x 21/4 “ )from approved quarry including cost and conveyance of all materials to site. Loading and unloading charges and labour charges for mixing, laying and curing etc. complete. Complying with std. specifications.. 13 a).Upto G.L. 14 b). 0.00 mt to 4.50mt 15 PlasteringinC.M. 1 : 5(onecement fivesand)to12 mmthickincludingallcostandconveyanceofallmaterials tositeincludingcostofcementwhichwillbepurcharedlocallybythecontractor and conveyanceofthesametotheactualworksiteandcostformworkincludingwatering curingandallleadsofgoodpotablewaterandallother. 16 SpecialPlasteringinC.M. 1 : 3 ( One cement, three sand) to10 mmthickincludingallcostandconveyance ofallmaterialstositeincludingcostofcementwhichwillbepurcharedlocallybythe contractor andconveyanceofthesametotheactualworksiteandcostformworkincludingwatering curingandallleadsofgoodpotablewaterandallother. 17 Supplying and filling with Well gravel from approved quarry including cost and conveyance of all materials and all labour charges for filling, watering & consolidation etc., complete as per standard specification 24 &25 NBC Part VI (S2) 8 28 V,VI S25 18 Plain Cement Concrete 1:2:4 mix,(one part of cement, two part of M.sand and four part of aggregate) mix using 20mm ISS HBG metal from approved Quarry including cost and conveyance of all materials and all labour charges for mixing, laying, compacting and curing the concrete and other incidental charges to site etc., complete.as per standard specification 28 V,VI S25 19 Supply and fixing of followingL angle truss including cost of Material conveyance of all material, fabrication and fixing charges etc.Completeas per ISI with rust preventive primer & ready to assemble condition for easy installation at site including dismantlingmaking necessary with power drill to the accessories such as supplying and fixing holdfasts, plastic bush inserts receiver runner bottom shock absorbers etc. Complete as Directed by the Departmental Officer. 20 Fabricating supplying and fixing of pre painted galvanium iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers. 21 Supplying and Painting thewalls with TwoCoatsWeather sealedExterior emulsion Paint as instructed by the departmrntal officers includingPreparation of surface curing, etc complete in all floorscomplying with standard specification. ( The Colour and shade of the paint shall be got approved by the departmental officers.) 22 Painting the new iron works such as steel doors, Windows,Ventilators windows bars,balustrades etc,in all floor withtwo coats of best approved first quality and colour of synthetic enamel paint of approved quality, colour and brand (to be approved by executive engineer before use on works ) over one the existing red oxide priming coat in all floors excluding cost of priming coat etc,complete complying with Standard Specification.
