Tender For Providing 04 Nos. 200 Kva Transformers And Other Allied Works In Sec-4 U/E Kurukshetra. (Including Six Years Defect Liability Period For Transformer And Three Years Free Mtc. And Defect Liability Period For Other Items, Free Of Cost)., kurukshetra-Haryana

Providing 04 Nos. 200 Kva Transformers And Other Allied Works In Sec-4 U/E Kurukshetra. (Including Six Years Defect Liability Period For Transformer And Three Years Free Mtc. And Defect Liability Period For Other Items, Free Of Cost).- 1 [13.32]Providing and fixing bolts including nuts and washers complete. [Through Rate] 2 [23.22.1.1]MCCB ,DISTRIBUTION BOARDS, MCB`s, RCCB`s, CHANGE OVER etc. 1.1. Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work. Double pole MCCB 16 to 63 Amp, 25 Ka [Through Rate] 3 [23.27.1]Supply and erection of Godrej Almirah typeM.S. pedestal made of 50 mm x 50 mm x 6 mm angle iron frame with 3.00 mm thick M.S. sheet covering including shutters with suitable hinges and locking arrangement with Godrej type handle including round bars . The top covering should have downward overhang of 75 mm on all sides of pedestal , having two sets of water proof ventilation holes of suitable size on the sides , at top and bottom , each set containing four Nos. holes to discharge the heat produced by the current . The shutters fixed with rubber gasket of superior quality and of suitable size to make it water proof .The pedestal duly painted both inside and outside with two coats of approved paint and primary coat and its legs are embeded upto the entire depth in 1:2:4 cement concrete block , projected 75 mm all around the pedestal and and 200 mm above the ground level including the cost of all labour and material required to complete the job in all respect upto the entire satisfaction of the Engineer-in-charge of the work:- 1. M.S. pedestal of size 600 mm wide , 750 mm high ,300 mm deep and bottom totally open , duly embeded in 1:2:4 cement concrete block of size 750 mm x 450 mm x 200 mm above ground level , having a base of size 900 mm x 600 mm x 250 mm below ground level.0 0 [Through Rate] 4 [24.4.2.4]STREET LIGHT 2.4. Supply and erection of GI bracket made of 32 mm dia medium class GI pipe, having 15 deg angle from horizontal, suitable for fixing on top of Street Lightpole 150 cm long, with 30 cm high suitable size pole cap. [Through Rate] 5 [24.5.1.1]MISCELLANEOUS ITEMS 1.1. Supply and jointing three core submersible flat cables of approved make with bare bunched copper conductor insulated and sheathed with PVC for submersible pump motors /fountain lights etc with voltage grade 1100 volts marked with IS:694, 1990 including cost of jointing, materials as well as carriage, loading, unloading etc. complete in all respect up to the entire satisfaction of Engineer- in-Charge.Submersible Copper Cable 3 Core 1.5 sqmm [Through Rate] 6 Supply Erection of PVC insulated and sheathed underground cable, loose in existing pipe or trenches 1100 volts core having solid aluminium conductor wires confirming to IS: 694 including making necessary connection complete in all respect up to entire satisfaction of the Engineer-in-charge.120 sqmm X3 ½core cable (Armoured) 7 SUPPLY AND ERECTION OF UNDERGROUNG CABLES OF VARIOUS SIZES LOOSE IN EXISTING PIPE OR TRANCHES COMPLETE WITH CONNECTIONS. 16 SQMM 4 core cable (Armoured) 8 Supply, Installation Testing and Commissioning of LED Street Light Fixture with Wattage range of (25 Watt) with body made of High Pressure Single Piece Die Cast Aluminum Alloy and cover made of PMMA (polymethymethacrylate) havingsystem Lumen)120Ipw with inbuilt Protection against Short Circuit, Miswiring, Over Voltage and Surge Protection of 6 KV. The IP of fixture and Driver Compartment should be IP66 and same for the LED Compartment. The driving current should be ( 700mA with THD ( 5% and PF ). 90 and Operating Voltage between 120-270V and CRI ) 70 and Impact Resistance of IK)05. The specifications as mentioned above should be duly tested and Mentioned in LM79 Report from Govt. Approved NABL Accredited Labratory and LM80 Report of LED Chip from the Manufacturer required to complete the job in all respect including erection on existing pole for fixing including connection of the same upto the entire satisfaction of Engineer-in-Charges of the work. (Warranty- 3 Years Including Driver against any manufacturing defect)(Including Three Years replacement warranty and three years Free Mtc./Defect Liability Period Free Of Cost). The logo of company should be embossed on the fixture. (Make:- Phillips/Bajaj/LT) 9 Supply, Erection and Transportation upto site including all taxes as per latest Govt. Instruction amended time again of Prestressed cement concrete pole as per IS: 1678/1960. 11 Mtr. Long 140mm x 200mm at top and 140mm x 400mm at bottom with working load of 400 kg. Buried 2.20 m in ground or as per UHBVNL specification complete in all respect up to the entire satisfaction of Engineer-in-Charge. 10 Supply and erection of 200 KVA outdoor type non sealed 3 phase 50 HZ 11/0.433/200 KVA Aluminum wound oil immersed naturally cooled distribution transformer complete with fitting and accessories inclusive of Ist filling of oil and confirming to ISS 2026/1977 with latest amendments complete in all respect and similarity of transformer should have been got type tested including making of plate form and installation of transformer upto the entire satisfaction of Engineer-in-Charge. Voltage Rated Frequency permitted at 75 ‘ Ci) No Load losses (Max) =220 wattii) Full Load losses (Max)= 1760 watt The above losses are maximum allowable and these would not be any positive tolerance. 11 S/E of 300 Sqmm single core unarmored power cable with aluminum conductor 650/1100 V confirming to ISS 1554 (Part-1) of 1988 IS 7098/Part-1/1988 with latest amendments upto respect upto the entire satisfaction of Engineer-in-charge. Make(Plaza/Havells/ICL/KEI/UNIVERSAL/ CIRTINA/Panasonic Anchor) 12 Supply and erection of 11 KVG.O. Switch with 9 Nos. post insulator suitable heavy duty with suitable copper male and female contents for 11 KV, G.I. Pipe, nut and bolts complete as per ISS:1816/1972 and ISS:2544/1963 as per UHBVN Specifications with latest amendments thereof complete in all respect. 13 Supply and erection of 11 KV Lightening Arrestor (conforming to ISS:3070/1985) with latest amendments complete in respect and erection of the same upto the entire satisfaction of the Engineer-in-charge. 14 SUPPLYING AND FABRICATION OF MS CHANNEL SIZE 100 X 50 X 6 mm MS CHANNEL SIZE 75 X 40 X 6 mm AS PER RELEVANT IS SPECIFICATION, PAINTING AND PRIMING COAT UPTO THE ENTIRE SATISFACTION OF ENGINEER-IN-CHARGE. 15 SUPPLYING AND FABRICATION OF MS ANGLE IRON SIZE 50 X 50 X 6 mm AS PER RELEVANT IS SPECIFICATION, PAINTING AND PRIMING COAT UPTO THE ENTIRE SATISFACTION OF ENGINEER-IN-CHARGE 16 Supply and Fabrication of M.S. Flat size 50 x 6 mm as per relevant IS specification along with painting and priming coat up to the entire satisfaction of Engineer-in-Charge. 17 Supply and Erection of fuse unit L.T. side of 100/200 KVA Transformer complete with wooden board cleats, aluminium strips M.S. clamp and M.S. Nuts and Bolts including all petty material required upto the entire satisfaction of Engineer-In-Charge. 18 SupplyErection of Barbed wire forH.T. Line on existing 11 mtr long pcc pole . 19 Supply and Erection of Danger plate for 11 KV line complete as per UHBVNL specification complete in all respect upto the entire satisfaction of Engineer-In-Charge. 20 S/E of 11 KV disc fitting (Hardware) with accessories suitable for stringing and sagging of ACSR Conductor 50 Sqmm. Conforming to relevant IS specification with latest amendments complete in all respect upto the entire satisfaction of Engineer-In-Charge. 21 S/E of Disc Insulator without fitting T and C Type Jay Shree Make (Conforming to ISS:2486 Part-I and II) with latest amendments complete in all respect and erection of the same upto the entire satisfaction of Engineer-In-Charge. 22 S/E of 11 KV G.I. Pins (long) for H.T. line (Conforming to ISS 2486 (Part-I and II) with latest amendments complete in all respect and erection of the same upto the entire satisfaction of Engineer-In-Charge. 23 S/E of 11 KV Pin Insulator Brown Glazed with creepage distance with 230mm Jaya Shree Make (Conforming to ISS 73/1971) with latest amendments complete in all respect and erection of the same upto the entire satisfaction of Engineer-In-Charge. 24 S/E / Erection of V-Shape Cross Arm as per REC specification / Approved by UHBVN for H.T. line made out of M.S. Channel 40 x 75mm flange thickness 7.3mm holes thickness 4.4mm (conforming of relevant provided in the web at the base for fixing of half clamp and 2 Nos. 20mm for G.I. Pin on the flange of the top. The plate of M.S. flat 50 x 6mm shall be welded on the top and bottom flange of both end of V-shape cross arm with 22mm of holes in the plate complete in all respect upto the entire satisfaction of Engineer-In-Charge. 25 S/E of G.I Pipe earthing set 40mm dia 2.5 Mtr. long shall be of medium class conforming to ISS: 1239(Part-I) with latest endments shall have 12mm dia holes at interval of 150mm on the entire surface of the earthing pipe shall be tapered and top and of G.I pipe shall be threaded and shall be provided with suitable size of G.I earth wire. The clamp shall be tightened to the earth pipe with 12mm dia galvanized M.S. Nut and Bolts and spring washers complete in all respect upto entire satisfaction of Engineer-In-charge. 26 Supplyand erection of Earthing Rod of 20mm dia and 2.5 Mtr. Long shall be tapered to be pointed at one end of about length of 50mm and other end of the rod shall flatten over a length of 150mm into 40mm and having two holes of 12mm dia and 50mm apart alongwith 16 SWG thick conduit pipe 25mm dia 3 Mtr. Long (conforming to IS 9537 (Part-I) enameled black painted complete in all respect upto the entire satisfaction of Engineer-In-Charge. 27 S/E of G.S.L. wire 8 SWG conforming to ISS: 280/1978/1963 with latest amendments complete in all respect and erection of the same upto the entire satisfaction of Engineer-In-charge. 28 S/E of M.S. Stay set complete with elbow and Nuts complete in all respect made out of M.S. Rod 18mm diaand 1.8mtr. long to with stand 1000 Kg load under tension and upper and theadedupto 0.25 Mtr. Length and elbow made out of 16mm dia M.S. round shall be welded firmly on M.S. Angle of size 50 x 50 x 6mm of 180mm and (conforming o ISS 226, ISS 1732/1971) with latest amendments three of and hexagonal Nuts conforming to ISS 136/1971 with latest amendments on pole complete in all respect upto the entire satisfaction of Engineer-In-Charge. S/E of stay set 4 Nos. for 11 Mtr. Long PCC polealong with GSS wire and Disc insulator complete. 29 S/E and Erection of ACSR Cond. (confirming to IS 398(PART-II)-1976 -1996,4826-1976 , IS: 1521-1972 and IS:1778-1980 with latest amendments and the erection of the same with accessories including stringing and sagging of conductor as well as jointing and binding with insulator at spots complete in all respect up to the entire satisfaction of the engineer –in - charge.ACSR Conductor 50 Sqmm 30 S/E of Guard made of G.I. Wire 8 SWG Conforming to ISS:280/1978/1963 with latest amendments complete in all respect and erection of the same upto the entire satisfaction of Engineer-In-Charge for L.T. Line. 31 S/E of M.S. Stay set complete with elbow and Nuts complete in all respect made out of M.S. Rod 18mm dia and 1.8mtr. long to with stand 1000 Kg load under tension and upper and theaded upto 0.25 Mtr. Length and elbow made out of 16mm dia M.S. round shall be welded firmly on M.S. Angle of size 50 x 50 x 6mm of 180mm and (conforming o ISS 226, ISS 1732/1971) with latest amendments three of and hexagonal Nuts conforming to ISS 136/1971 with latest amendments on pole complete in all respect upto the entire satisfaction of Engineer-In-Charge.S/E of stay set 2 No. for 9 Mtr. Long PCC polealongwith GSS wire and Disc insulator complete with Clamps and Nuts and Bolts. 32 S/E of L.T. Shackle Insulator of size 90 x 75mm (conforming to ISS:1445/1977) with latest amendments complete in all respectand erection of the same upto the entire satisfaction of Engineer-In-charge. 33 S/E of M.S. D-Strap type –I made out of M.S. Flat 40 x 6mm and suitable for L.T. insulator 90 x 75mm with latest amendments complete in all respect and erection of the same upto the entire satisfaction of Engineer-In-Charge excluding cost of nuts an bolts . 34 Supply, Erection and Transportation upto site including all taxes as per latest Govt. Instruction amended time again of Prestressed cement concrete pole as per IS: 1678/1960. 9 Mtr. Long 105mm x 115mm at top and 105mm x 315m at bottom with working load of 200 kg. Buried 1.80 m in ground or as per UHBVNL specification complete in all respect up to the entire satisfaction of Engineer-in-Charge 35 Providing and fixing bolts including nuts and washers complete. 36 S/E and Erection of ACSR Cond. (confirming to IS 398(PART-II)-1976 -1996,4826-1976 , IS: 1521-1972 and IS:1778-1980 with latest amendments and the erection of the same with accessories including stringing and sagging of conductor as well as jointing and binding with insulator at spots complete in all respect up to the entire satisfaction of the engineer –in - charge.ACSR Conductor 30 Sqmm 37 S/E of Guard made of G.S.L. Wire 8 SWG Conforming to ISS:280/1978/1963 with latest amendments complete in all respect and erection of the same upto the entire satisfaction of Engineer-In-Charge for H.T. Line. 38 Supply and Fabrication of M.S. Angle Iron size 50x50x6mm as per relevant IS specification alongwith painting, priming coat upto the entire satisfaction of Engineer-in-Charge.

INR 1000 /-

INR 50360.0 /-

INR 25.17 Lakhs /-