|
| 1 | Supply, installation, commissioning and testing of magnetic lock type battery operated telephonic communication system suitable upto G+15 upper floors for the lifts installation at NOFRA of any make system, speaker embedded/ engraved/ concealed/ sanctioned one in each car and ground floor in front facia of lift and making good the disturbed surfaces one hand set with receiver in machine rooms properly fixed to wall in bracket including travelling cable and required accessories for fixing complete all as specified and directed by Engineer-in-Charge. |
| 2 | Supply and fixingofentry sign board for Elevators suitable up to G+14 floors, made of stainless steel SS 304, 18 SWG (rust free) having size20\" x 6\" (LxW) along with black letters andsymbol showing Officer or Generalat Nofra complete with all fittings arrangements and make good the surface after replacing the same complete all as specified and directed by Engineer-in-Charge. |
| 3 | Supply and fixingofEmergency contact number board for Elevators car cabin made of stainless steel SS 304, 18 SWG (rust free) having size 9\" x 9\" (LxW) along with black letters at Nofra complete with all fittings arragements and make good the surface after replacing the same complete all as specified and directed by Engineer-in-Charge. |
| 4 | Supply and fixingofentry sign board for Elevators suitable up to G+15 floors, made of stainless steel SS 304, 18 SWG (rust free) having size not less than 40 cm x 10 cm (L&W) along with black letters andsymbol showing Officer or Generalat Nofra complete with all fittings arrangements and make good the surface after replacing the same complete all as specified and directed by Engineer-in-Charge. |
| 5 | Supply and fixingofEmergency contact number board for Elevators car cabin made of stainless steel SS 304, 18 SWG (rust free) having size not less than 20 cm x 20 cm (LxW) along with black lettersat outlying area of Nofra complete with all fittings arragements and make good the surface after replacing the same complete all as specified and directed by Engineer-in-Charge. |
| 6 | Material and Labour for earth continuity conductor or main earthing lead fixed to wall on batten or recess or burried in ground or drawn in conduit /pipe or fixed to poles or any other indicated situation for loop earthing etc. as required25x4 mm galvanised iron strip. |
| 7 | Supply and fix aluminium strip of size 25X4 mm with saddles and fixing screws etc. for roof conductors and down conductors above gound from test point tolift machine room to be terminated to the control panel, machine and other equipment installed in machine room including taking down old complete all as specified and directed by Engr-in-Charge. |
| 8 | Supply and fix aluminium strip of size 32X6 mm with saddles and fixing screws etc. for roof conductors and down conductors above gound from test point tolift machine room to be terminated to the control panel, machine and other equipment installed in machine room including taking down old complete all as specified and directed by Engr-in-Charge. |
| 9 | Matrial and labour forEarthing complete with galvanized steel earth electrode600x600x6mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanized earth strip 32 x 6 mm by means of bolts, nuts & washers of galvanized iron or steel up to the test point all as shown in electrical plate No.3 of SSR Part-I connected to lifts including PCC chamber pit, RCC cover, GI funnel with wire mesh, GI protection pipe of 50 mm dia for earth lead and 20mm GI pipe for watering , excavation and earth work in any type of soil, filling the pit with charcol and common salt surrounding the earth plate complete including connecting up to test point and testing on completion including taking down old complete all as specified and directed by Engr-in-Charge. |
| 10 | Material and Labour for required Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit /pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire all as directed by engineer-in-charge. |
| 11 | Supply and fixing, layingPVC insulated XLPE, armoured LT cable, 1100 Volts grade with aluminium conductor of size 4 core 10 Sqmm laid in trenches/ through pipe/ ducts or fixed on wall etc taking down old unserviceable cable ,complete all as specified and as directed. |
| 12 | Supply, laying including testing cable PVC insulated XLPE, armoured LT cable, 1100 Volts grade with aluminium conductor of size 3.5 core 70Sqmm laid in trenches/through pipe /ducts or fixed on wall etc complete all connections to LT panel with proper size glands & lugs including taking down old unserviceable cable all as specified & directed. |
| 13 | Supply, laying including testing and commissioning PVC insulated XLPE, armoured LT cable, 1100 Volts grade with aluminium conductor of size 3.5 core 95Sqmm laid in trenches/ through pipe /ducts or fixed on wall etc complete all connections to LT panel with proper size glands & lugs taking down old unserviceable cable all as specified & directed. |
| 14 | Supply, laying including testing and commissioning PVC insulated XLPE, armoured LT cable, 1100 Volts grade with aluminium conductor of size 3.5 core 120Sqmm laid in trenches/through pipe /ducts or fixed on wall etc taking down old unserviceable cable complete all as specified & directed. |
| 15 | Matrial and labour for 20mm thickgranite slab (of any type) tiles machine cut, mirror polished set on vertical surfacesallround with lift facial elevation including back casting in CM (1:3)15 mm thick and joint filling with white cement with pigment to match with shade of granite for lift architrave including taking down all granite at all floors complete all as specified and directed by Engineer-in-Charge. |
| 16 | Supply, installation, testing and commissioning of LT Feeder Pillar Panel CPRI approved mounted on angle iron framegrouted on floor,cubical outdoor type, with both side opening with minimum size 900 x 900 x 500mm or as per existing size of all breakers and controls, for 415V, 3 phase,made of 3 mm thick CRCA sheet weather, vermin proof factroy fabricated, CPRI approved, front open hinged door with locking arrangement powder coated, individual compartment for MCCBs and 400 Amps rated Aluminium bus bar, top and bottom cable entry including disconnecting cable connections Panel and fixing/connecting in new installed panel with provisions of thimble/lugs and necessary framework and PCC foundation including shifting of existing (old) LT Panel, if any, making arrengement for fixing of panel and making good to disturbed surface as directedcomprising of the following :-(a) MCCB 250 Amps, 36 KA, FP - 01 Nos(b) MCCB 100 Amps, 25 KA, FP - 02 Nos(c) MCB DP 40 Amps - 04 Nos(d) Control panelwiring with 2.5 sq mm multistranded, PVC insulated copper conductor cable between voltmeter, Ammeter, and their selector switch complete withCTs of ratio 250/5 A- 1 Nos ,100/5 A - 2 Nos, voltmeter flush pattern type 96 mm square dial -1 nos, Ammeter digitalCT operated 96 mm square dial flush pattern type -3 Nos, indication lamp for 3 phase and control fuses-3 Nos complete . (e) Aluminium bus bar 400 Amps for phase & 250 Amps for neutral complete with bus bar insulator, nuts & bolts complete.(f) Power panel wiring between bus bar to MCCB of different capacity with PVC insulated multistranded copper cable , singlecore ,1100 volts grade of appropriate size complete. |
| 17 | Supply, installation, testing and commissioning of LT Panel CPRI approved mounted on angle iron frame 40x40x5 mm grouted on floor,cubical outdoor type, with both side opening Minimum size 900x1200x600 mm or suitable fixing of all breakers and controls, for 415V, 3 phase,made of 3 mm thick CRCA sheet weather, vermin proof factroy fabricated, CPRI approved, front open hinged door with locking arrangement powder coated, individual compartment for MCCBs and 400 Amps rated Aluminium bus bar, top and bottom cable entry including disconnecting cable connections Panel and fixing/connecting in new installed panel with provisions of thimble /lugs and necessary framework and PCC foundation including shifting of existing (old) LT Panel, if any, making arrangement for fixing of panel and making good to disturbed surface as directedcomprising of the following :-(a) MCCB 250 Amps, 36 KA, FP - 01 Nos (b) MCCB 100 Amps, 25 KA, FP - 02 Nos (c) MCCB 63Amps, 16 KA, FP - 02 Nos (d) MCB DP 40 Amps - 02 Nos (e) Control panelwiring with 2.5 sq mm multistranded, PVC insulated copper conductor cable between voltmeter, Ammeter, and their selector switch complete withCTs of ratio 250/5 A- 1 Nos ,100/5 A - 2 Nos, voltmeter flush pattern type 96 mm square dial -1 nos, Ammeter digitalCT operated 96 mm square dial flush pattern type -3 Nos, indication lamp for 3 phase and control fuses-3 Nos complete .(f) Aluminium bus bar 400 Amps for phase & 250 Amps for neutral complete with bus bar insulator,nuts & bolts complete.(g) Power panel wiring between bus bar to MCCB of different capacity with PVC insulated multistranded copper cable , singlecore ,1100 volts grade of appropriate size complete. |
| 18 | Supply, install, commission and testingLT panel board, indoor type, manufactured by a CPRI approved factory, floor mounted, dust & vermin proof, front and rear operated doorwithnecessary locking arrangement with MS-75 for base frame and angle iron 50 x 50 x 6 mm for legs , four nos legs 750 mm long and CRCA sheet dulypowder coated both internally and externally. The panel shall be suitable for 415 Volts, 50 HZ, 3 Phase 4 wire system and shall be complete with suitable capacity copperbus bar (1.5 times the incoming switch gear current rating) alongwith complete internal wiring with suitable size of copper cable, CT etc includign taking down existing rusted panelcomplete all as specified and as directed with the following accessories :-INCOMING(a)MCCB 4 pole, 415 Volts, 200 Amps, breaking capacity 25 KA - 01 NosOUTGOING(a)MCCB 4 pole, 415 Volts, 100 Amps, breaking capacity 25 KA - 03 Nos(b) MCB TPN 40 Amp - 04(c) MCB DP 25 Amp - 02(d)Multifunctional meter flush mounting type 96 x 96 mm - 01 Nos(e) Indicator lamp (RYB) (set of three) - 01 Set. |
| 19 | Supply, install, commission and testingLT panel board, indoor type, manufactured by a CPRI approved factory, floor mounted, dust & vermin proof, front and rear operated doorwithnecessary locking arrangement with MS-75 for base frame and angle iron 50 x 50 x 6 mm for legs , four nos legs 750 mm long and CRCA sheet dulypowder coated both internally and externally. The panel shall be suitable for 415 Volts, 50 HZ, 3 Phase 4 wire system and shall be complete with suitable capacity copperbus bar (1.5 times the incoming switch gear current rating) alongwith complete internal wiring with suitable size of copper cable, CT etc includign taking down existing rusted panelcomplete all as specified and as directed with the following accessories :-INCOMING(a)MCCB 4 pole, 415 Volts, 200 Amps, breaking capacity 25 KA - 01 NosOUTGOING(a)MCCB 4 pole, 415 Volts, 100 Amps, breaking capacity 25 KA - 02 Nos(b) MCCB 4 pole, 415 Volts, 63 Amps, breaking capacity 25 KA - 02 Nos(c) MCB DP 40 Amp - 02(d) Voltmeter,digital type 0- 500 volt,with selector switch -01 set(e) Phase indicating lamps LED type ( red , yellow, blue) -01 set(f)) Ammeter Digital type 0-500Amps, with selector switch and CT\"-1set . |
| 20 | Supply ,install , testing and commissioning LT panel in replacement, indoor type, 800 Amps Aluminiumbus bar with colour coded heat shrinkable sleeves, IP 43 Protection class, factory fabricated, cubical panel,provn for ventilation , angle iron frameand four legs of 50x50x6mm thick angle iron ,1 ft long grouted on PCC foundation of height not less than 40 cm from the ground level , grouting properly, free standing type, made out ofCRCA sheet with locking arrangement, both sides openable, having cable gallery of suitable size for easy connection of cables, dust vermin proof suitable for 3 phase 4 wire 415 volt 50Hz AC including Digital multi display meter with selector switch,phase indicator lamp(RYB), suitable size copper conductor control wiring and power coating, connecting the cable with necessary cable glands, lugs etc for all incoming & outgoing cables, proper arrangement for ventilation accomodating the following items and space as per site including taking down old rusted panel complete all as specified and directed with the following accessories :-(a) MCCB 630A, rated for 415Volt, 4 pole, 3 Phase, rupturing capacity of 36KA, Thermal-Magnetic type MCCB, Qty-01 No. (incoming), the service short circuit breaking capacity (Ics) shall be equal to ultimate breaking capacity (Icu) i.e. Ics =100% Icu. (Thermal adjustment and magnetic adjustment setting)(b) MCCB 250A, Rated for415Volt, 4 pole, 3 Phase rupturing capacity of 36KA, Thermal-Magnetic type MCCB, Qty-04 No. (Outgoing) the service short circuit breaking capacity (Ics) shall be equal to ultimate breaking capacity (Icu) i.e. Ics =100% Icu. Fixed Thermaland magnetic setting.(c) MCCB 160 A, Rated for415Volt, 4 pole, 3 Phase, rupturing capacity of 25kA, Thermal-Magnetic type Qty-02 No (Outgoing) (d) Indicating lamp - 02 sets (e) Digital volt / ammeter-02 Nos with selector switch(f)CT coil400/5A - 01 |
| 21 | Supply, fix, install, testing and commissioning of feeder pillar box ,out door type cubical shape,three phase, 4 wire, copper bus barrating 400 amps for phases and 200 amps for neutral made out of CRCA sheet ,3 mm thick ,factory fabricated , CPRI approved , powder coated ,dust and vermin proof , provn for ventilation , angle iron frameand four legs of 50x50x6mm thick angle iron ,1 ft long grouted on PCC foundation of height not less than 40 cm from the ground level , grouting properly ,and of suitable size to accommodate the items mentioned belowand having separate compartment /chambers for cable gallery busbar,switch gearand front sideopenable , back side fixedl etc all as specified and comprising of following including necessary cable connections to the MCCBs ,voltmeter,Ammeter and cable lugs etc including taking down existing panel complete all as specified and directed with the following accessories :-.(i) MCCB 4 Pole, 415V, adjustable type, 200 Amps with breaking capacity 36KA Make- Schneider/Havells/Legrand-01 No (Incoming)(ii) MCCB4 pole 415V fixed type, 25 to 100 Amps with breaking capacity 16KA. Make- Schneider/Havells/Legrand -03 Nos (outgoing)(iii)MCB Isolator 40 Amps- 06 Nos (outgoing)(iv) Voltmeter,digital type 0- 500 volt,with selector switch -01 set(v) Phase indicating lamps LED type ( red , yellow, blue) -01 set(vi)Ammeter Digital type 0-500Amps, with selector switch and CT\"-1set . |
| 22 | Taking down old MCCBs andSupply & fixing in new MCCBs 125 Amps 415 V 16 KA 4 pole thermal magenetic adjustable type complete all as specified and directed by Engineer-in-Charge. |
| 23 | Taking down carefully aluminium point wiring (light, fan, socket or power) complete, (fittings such asswitches,ceilingroses, pendants, regulators sockets etc to be measured separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified. |
| 24 | Material and Labour for point wiring complete with 1.5 sqmm single core multistranded FRLS PVC insulated unsheathed copper conductors 1100 volts grade drawn through and including PVC non-metallic casing and caping of size not less than 25mm width, ISI marked with accessories fixed on wall/ ceiling/ truss etc with PVC non metallic ISI marked terminal boxes/ modular boxes surfacing on wall including one FRLS PVC insulated & sheathed multistranded green colour copper conductor 1.5 sqmm as earth continuity conductor connected to common earth as earth dolly for :- |
| 25 | One light point /Exhaust Fan Point controlled by one switch SP one way. |
| 26 | One 3 Pin socket outlet 5 Amps on independent board |
| 27 | Supply and fixing in repair Modular Switch, 6Amp, One way, 1 module. |
| 28 | Supply and fix ceiling rose surface bakelite with ISI mark, flush type with ISI mark three terminals complete all as specified. |
| 29 | Supply and fixing in repair Modular Socket oulet, 6 Amps, 2/3 pin combined, 2 module. |
| 30 | Supply and fixing in repairModular white cover plate with Frame 2 Module complete all as specified and directed. |
| 31 | Supply and fixingin repair Modular white cover plate with Frame 3Module complete all as specified and directed. |
| 32 | Supply and fixingModular white cover plate with Frame 6 Module complete all as specified and directed. |
| 33 | Supply and fixing modular metal flush box 6 Module concealed in wall complete all as specified and directed. |
| 34 | Supply and fixing in repair Polymer extruded channel, with opaque diffuser for glare free light 1x18/20 WH 04 feet longaccessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable sizewithall accessories complete all as specified and directed. |
| 35 | Supply and fixing in repair linear Aluminium Batten LED T/L 20 W rated input voltage 140V AC -270 V AC Lumens efficiency 100 Lm/W Aluminium Extruded chanel Powder coated with opaque diffuser for glare free light complete with accessories internally prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable sizecomplete all as specified and directed. |
| 36 | Taking down old sheet metal enclosure, supply and fixing in repair sheet metal enclosure 08 way Double door type having protection IP-42, with 200 Amps rated bus bar connecting with existing wiring circuits by providing copper pin terminals of suitable size complete all as directedcomprising of the following |
| 37 | MCB Four pole 63 Amps, 240 Volts |
| 38 | MCB SP 6-32 Amps, 240 Volts |
| 39 | Supply and fixing in repair single phase sheet metal powder coated double door distribution board 4 way comprising with following :- (a) MCB SPN 40Amps 240Volts, 10KA - 1 No (\"C\" Series) (b) MCB SP 6 - 32Amps 240Volts - 2No (\"C\" Series) |
| 40 | Complete lift Machine Overhauling hoist way and induction motor with capacity from 7 HP to 15 HP both by opening of Gear removing old dirty oil, cleaning & replacing of new gear oil refitting of the same with new packing & adjustment of thrust bearing & keeping it into perfect working order,opening of the hoist way machine by taking the main pulley and diverter pulley and complete refixing after overhauling all as specified and directed by Engineer-in-Charge. |
| 41 | Taking down unserviceable main pulley with complete set Supplying & fixing new main pully with complete set complete all as specified & directed by Engr-in-Charge. |
| 42 | Dismantling and taking out all defective batteries from existing ARD and supply and fixing new maintenance free batteries suitable for ARD including necessary connection like battery terminals of brass and copper lead heavy duty to connect the batteries terminal of 12 VDC, 18 AH (one set of 04 nos batteries for each ARD). |
| 43 | Taking down old unserviceable Aluminium chequered plate supply & fixing new aluminium Chequered plate of thickness upto 5mm including removing existing plates complete all as specified and directed by Engineer-in- Charge. |
| 44 | Dismantling and taking outARDcontrol system and commissioning andtesting of new ARD system including PCB cards/diodes suitable for upto 15 HP motor including wiring with connected item in existing building.Make: Must be sitable for Shree Elevators/Monarch/As per exiting make at site complete all as specified and directed by the Engr-in-charge |
| 45 | Dismantling and taking out old unserviceable buffer spring for lift and supplying & fixing new buffer spring complete all as specified and directed by Engr in Charge. |
| 46 | Supply & fixing in repairs DB 8 way Double door SPN type, 240 volt having protection IP-42, with 200 Amps rated bus bar connecting with existing wiring circuits by providing copper pin terminals of suitable size complete all as directed |
| 47 | Supply and fixing in repairsMCB SPN 40 to 63 amp rating 240V, 10KA \"C\" curve miniature circuit breaker (MCB)and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specifed and directed by Engr in Charge. |
| 48 | Supply & fixing in repairs MCB SP 06-32 Amps, 10 KA rating complete all as specified anddirected. |
