|
| 1 | Supply and fix Tripple layer Rotational moulded polytheylne water storage tank (cylindrical ) with closed top hoisted and fixed in position of capacity 10000 Ltr. (Make : SintexStar/Cello/mega) |
| 2 | Supply and laying in trench/fixed on wall/floors galvanized steel water tubing medium grade ISI marked of the following sizes incl all fittings such asbends elbows, tees, short pieces, connectors, back nuts, diminishingpieces, caps and pigs, unions etc. complete all as directed . Make Jindal/Tata/Prakash Surya/Zenith.Note :- Necessary excavation and earth work shall be measured and paid separately |
| 3 | (a) 15mm bore |
| 4 | (b) 20mm bore |
| 5 | (c) 25mm bore |
| 6 | (e) 40mm bore |
| 7 | (f)50mm bore |
| 8 | (g) 80mm bore |
| 9 | S&F gunmetal globe or gate valve with iron wheel head screwed bolt ends for iron pipe of the following sizes complete all as specified and directed by Engineer-in-charge. Make : Leader/Zoloto |
| 10 | (a) 15mm bore |
| 11 | (b) 20mm bore |
| 12 | (c) 25mm bore |
| 13 | (d) 40mm bore |
| 14 | (e) 50mm bore |
| 15 | Supply and fixing Ball brass valves high pressure with polythene flote and flynut complete secewed for iron pipe or brass feerrule 20mm dia including taking down u/S valve complete all as specified and directed by Engineer-in-Charge. |
| 16 | Supply, installation, commissioning and testing of pumping set, centrifugal, electric driven, supplied and installed complete of 5 HP 3.7 KW and rating MIKS 32C sufficient for 450 LPM and discharge head range 50 Meters,connection cable and PCC foundation complete all as specified and directed by Engr-in-charge |
| 17 | M&L Rolled mild steel in compound girders and stanchions lattice girders, arial masts, stagingand the like including caps , bases, splices etc. built up from two or more beam or channel sections or angles with plates including all lattice bars, stiffeners, gusset plates,wire meshetc. conforming to Fe 410-W (Gde-E-250) quality -A, for fabrication of shed of DG setall as specified and directed by Engineer-in-Charge. |
| 18 | Prepainted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified, all as specified and directed. |
| 19 | Prepainted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridge, hips, valley/ eaves/ rain water gutters, drip and straight flashing (length and girthas fixed), fixed with self tapping screws all as specified |
| 20 | M&L Brick work with sub classs \"B\" bricks, straight or curved on plan exceeding 6.0 mtr mean radius built in 1:4 cement mortar complete all as specified and directed by Engineer-in-Charge. |
| 21 | M&L 15mm thick, Plaster/rendering on fair faces of brick work or one side of lathing in cement mortar 1:4, finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge. |
| 22 | M&L Hardcore of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface for PVC tankfoundation work, complete all as specified and directed by Engineer-in-Charge. |
| 23 | M&L PCC 1:4:8, M-7.5, type D-2, (using 40mm graded crushed stone aggregate), 100mm thick as in sub base of floor for PVC tank peding complete all as specified and directed by Engineer-in-Charge. |
| 24 | M&L PCC 1:2:4, M-15, type B-1 (using 20mm graded crushed stone aggregate), 100mm thick as in floor finsihing for PVC tank peding , finishing cement concrete surface even and smooth using extra cement, and coping of poles complete all as specified and directed by Engineer-in-Charge. |
| 25 | M&L PCC 1:3:6,M-5, type E-2 (using 40mm graded crushed stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed by Engineer-in-Charge. |
| 26 | M&L for Applying two finishing coat on walls surface of oil bound distamper (oil emulsion ) on walls, complete all as specified and directed |
| 27 | M&L 75mm thick PCC type C-2 (1:3:6) using 40mm graded stone aggregate as in sub-base complete all as sprecified and directed |
| 28 | Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in & raming earth/ briken rubble mixed with earth around, in layers n. exc. 25 cm watering, & removing surplus soil to a distance n exc 50m & making good surface in Hard/ldense soil. complete all as specified and directed. |
| 29 | S & F mild steel security chain link fancing 60mm x 60mm with PVC coated mesh made out of 3mm dia MS wire and 1.00mm thick PVC coating including binding wire complete all as specified and directed |
| 30 | M&L for dismantling of existing panel including disconnecting connected cables, etc. and supplying, installing, testing and commissioning of factory made LT cubical double door both front and rear side openable, Indoor type, of Suitable to accomodate the following accessories made out of CRCA sheet 2 MM thick duly powder coated with Seimens Grey Shade RAL 7032,totally enclosed, dust and vermin proof outer cubicle with working voltage of 415V, 50 Hz, 3 phase 4 wire fully compartmentalised with door for each compartment. Cubiclle must be extendible in both ends having both front and rear side openable and should be provided with suitable louvers for ventilation. Bus bars provided shall be adequately supported on insulators to withstand dynamic stresses due to short circuit current and shall be suitably colour coded with heat shrinkable sleeve for phase indication. The standard phase arrangement when facing the switchgear shall be R-Y-B from left to right. The bus bar connections and their insulated supports shall be mechanically strong, and shall withstand all the stresses which shall be imposed upon them in ordinary working due to fixing, vibration, fluctuation in temp., shot-circuit or other causes. The bus bar should be supported on DMC. Internal wiring should be done with 2.5 sqmm multi-stranded copper conductors and shall be properly bunched, tied, ferruled for proper identification, crimped and shall be connected with suitable lugs and PVC sleeves, etc. The bottom of the panel should contain detachable plate having provision for entry of armoured cable of adequate size with glands. Threaded earthing studs - 02 Nos shall be provided at the bottom and lifting lugs of suitable size at top to lift the panel safely shall be made. The cubicle incomer MCCB as well as outgoings shall have copper TPN/TP , current rating not less than 1.5 times the rated capacity of individual feeders inclding all broken surface making good . The cubicle should be inclusive of following : |
| 31 | Location : LT Panel near main water tank at Mankot area(A) INCOMING -(a)MCCB -DPX3 160 thermal & magnetic type 4 pole 415 volt 25 kA breaking cap. adjustable thermal release range 63 Amps Cat ref no. 4200 55 of make Legrand or equivalent in M/s Schenider/M/s Siemens – 01 No. |
| 32 | (B) OUTGOING -(a)MCCB -DPX3 160 thermal & magnetic type 4 pole 415 volt 25 kA breaking cap. adjustable thermal release range 40 Amps Cat ref no. 4200 52 of make Legrand or equivalent in M/s Schenider/M/s Siemens – 02 Nos.(b)DOL startor for 5 HP three phase 415V -02 Nos of Make L&T or equivalent as specified in Appx c complete all as spd and directed.including contol wiring & motor protector assembley having dry run protection, phase sequence corrector, earth leakage protection, single phase protection, high voltage and low voltage, time delay power programme time switch complete- 02 Nos(c) Multi function meter having LCD Display,96 x 96 sq.mm - 01 No(d) Current transformer of suitable ratio, Accuracy - 5VA, Class - 2. MAKE AE/NSDA/PRINZ(e) LED Indicators rivved lens with trimmed collar- Red, Yellow and Blue - 1Each Set. Make : TEKNIK/SELECT/L&T(f) Aluminium bus bar of rating150 Amps rating for R-Y-B Phase and Neutral.(g) Base frame for cubical mounting made out of 40x40x6mm equal angle iron duly painted.(h) Foundation for the panel should provided with PCC 1:4:6 at a depth of 150 MM below G.L. and 100 MM above the G.L. with slot openings for I/C and O/G cables. |
| 33 | M&L construction of brick masonary valve pit built in cement mortar 1:6 including all excavation and earth work in any type of soil and disposal of surpluse soil to a distance not exc. 50 mtr all as directed by Engineer-in-charge including 10mm thick plastering internally in CM 1:4 and flush pointing in same mortar to brick work externally as work proceeds and cement concrete in foundation PCC (1:4:8) type D-2 15 cm thick & PCC 1:3:6 type C-1 coping, including 75 mm thick & hard core of gauge and exc. 63mm using broken stone /bolder, MS sheet cover 3.15 mm thick MS angle iron frame, handle locking arrangement and painting to steel surfaces including dismantling of old valve pit complete all as specified and directed by Engineer-in-Charge. incl necessary excavation earth work of the followingsizes :- |
| 34 | (a) 750 mm x 750mm x 750mm. |
| 35 | (b) 900mmx900mmx900mm |
| 36 | Supplying, fixing, jointing, connecting & testing intrenches XLPE/PVC insulated PVC sheathedcable heavy duty1100 volts grade, aluminum conductor in trenches / ducts /on wall surface as in repairs/replacement of old unserviceable cable of following sizes all as specified and directed. |
| 37 | (b) 4 core 16 Sqmm |
| 38 | M&L for sand cushioning for cable protection 8 cm below the cable and 15 cm above the cable complete all as specified and directed |
| 39 | Supply and lay burnt bricks sub class `B’ of size 230x115x75mm laid dry over sand cushioning in trenches as protection on the cable all as directed |
| 40 | Excavation in trenches in any type of soil n. exc 1.5mtr wide and n. exc 1.5mtr depth for LT cable /GI tubing and getting out in Hard/dense soil all as specified. |
| 41 | M&L for returning, filling in including sperading, leveling watering and well ramming in layers n. exc 25 cm thick each layers in soil all as specified and directed. |
| 42 | M&L for removal of surplus soil to a distance not exceeding 50 mtr and deposting where directed and at a level not exceeding 1.5 mtr above the starting point all as specified and directed by Engr-in-Charge. |
| 43 | S&F in replacement of CI foot valve of 50mm dia all as specified and directed by Engineer-in-Charge. |
| 44 | M&L for earthing complete with GI earth plate electrode of size 60cm x 60cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of the plate not less than 1.5m below the normal ground level connected with GI strip 25 x 4mmby means of bolts, nuts, check nuts & washers of galvanished iron steel including necessary excavation and earth work in any type of soil, removing surplus soilto a distance not exc 50m, with and including PCC chamber in PCC (1:2:4), type B1,using (20mm graded stone aggregate),\"mild steel angle iron frame\" made out of MS angle iron of size 40x40x6mm thick duly painted with two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer hinged with and including 6mm thick CI cover with handle, watering arrangement with funnel internally secured with wire mesh with 40mm dia mediumgrade pipe for watering 40mm dia light grade, GI pipe for lead protection in and including alternate layers of charcoal dust and common salt complete all as shown inelectrical \"plate No \"3\" and connected to earthing test point all as specified and indicated including testing on completion, complete all as specified and directed. |
