maintenance of Completed Scheme Under Nazul A/C-Ii (Hz). Maintenance Of Open Gym Equipment In Various Parks Under The Jurisdiction Of Horticulture Division-1 (Specialized Work).-SCHEDULE AEarth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.(a) All kinds of soil. 2 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 gradedstone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. (a) 40 mm thick with 20 mm nominal size stone aggregate. 3 Excavating holes more than 0.10 cum & upto 0.5 cum including getting out the excavated soil, then returning the soil as required in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering etc, disposing of surplus excavated soil, as directed within a lead of 50 m and lift upto 1.5 m.(a) All kinds of soil 4 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :(a) 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) 5 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :(a)1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) 6 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:(a)Cement mortar 1:6 (1 cement : 6 coarse sand) 7 Extra for pre finished nosing to treads of steps of marble stone. 8 Providing and laying factory made chamfered edge Cement Concretepaver blocks in footpath, parks, lawns, drive ways or light traffic parkingetc, of required strength, thickness & size/ shape, made by table vibratorymethod using PU mould, laid in required colour & pattern over 50 mmthick compacted bed ofsand, compacting and proper embedding/layingof inter locking paver blocks into the sand bedding layer through vibratorycompaction by using plate vibrator, filling the joints with sand and cuttingof paver blocks as per required size and pattern, finishing and sweepingextra sand. complete all as per direction of Engineer-in-Charge.(a) 60 mm thick cement concrete paver block of M-35 grade withapproved colour, design & pattern. 9 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge). 10 40 mm thick fine dressed stone flooring over 20 mm (average) thick baseof cement mortar 1:5 (1 cement : 5 coarse sand) with joints finished flush. (a) Red sand stone 11 Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) : (i) Gang saw cut stone (a) 30 mm thick White sand stone 12 SCHEDULE BAir Walker: Providing and fixing air walker with below specifications:1. Dimensions (LxWxH): 1100 x 550 x 1480mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. ‘U’ shaped main frame of NB 65mm (G.I.) ‘C’ Class Pipe. 4. All other pipes of NB 32mm (G.I.) ‘C’ Class (‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness, UV resistant and colored. 9. Foothold made of nylon alloy with rounded edges to prevent impact and injury. 10. Maintenance concealed self lubricated bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 11. The equipment are fitted with inbuilt limiters to prevent unwanted movements12. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 14. High S S steel with galvanized nut bolts are used for assembly. 15. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment and certify from IS9001/ISO 1400116. Self-Explanatory stainless steel label fixed on equipment for ease of use.Including maintenance cost for 2 years 13 Air Swing: Providing and fixing air swing in a pair with below specifications:1. Dimensions (LxWxH): 1150 x 900 x 1250 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. Main frame of NB 50mm (G.I.) ‘C’ Class Pipe. 4. Handle support frame of NB 40mm (G.I.) ‘C’ Class Pipe.(‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) 5.All Pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Handle bars are provided with high end quality rubber grips. 9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 10. Foothold made of nylon alloy with rounded edges to prevent impact and injury. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly. 16. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment.17. Self-Explanatory stainless steel label fixed on equipment for ease of use.Including maintenance cost for 2 years 14 Horse rider station: Providing and fixing horse rider station with below specifications:1. Dimensions (LxWxH): 1000 x 600 x 1100 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make3. Main frame of NB 65mm (G.I.) ‘C’ Class Pipe. 4. Handle support frame of NB 50mm (G.I.) ‘C’ Class Pipe.(‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters)5.All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 9. Foothold made of NB 25mm (G.I.) ‘C’ Class Pipe. 10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly. 16. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment.17. Self-Explanatory stainless steel label fixed on equipment for ease of use.Including maintenance cost for 2 years 15 Stair Stepper:Providing and fixing stair stepper in a combination pair with a stepper on one side and a twister on other side with below specifications:1. Dimensions (LxWxH): 1000 x 800 x 1400 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make(‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters)3. Twister main frame of MS pipe 80 x 40mm 4. Stepper main frame of MS pipe 80 x 40mm. 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Foothold made of nylon alloy with rounded edges to prevent impact and injury. 9. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 10. The equipment is fixed on ground with concrete of minimum strength M-25 and Expansion Bolts. 11. Once the concrete is set, the equipment is fixed on to it.12. High tensile steel with galvanized nut bolts are used for assembly. 13. Equipment made to EN16630 International standard for outdoor fitness equipment.14. Self-Explanatory stainless steel label fixed on equipment for ease of use. 16 Leg Press: Providing and fixing leg press in a pair with below specifications:1. Dimensions (LxWxH):2000 x 550 x 1600 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. Main frame of NB 50mm (G.I.) ‘C’ Class Pipe.(‘NB’ stands for Nominal Bore i.e., Internal Diameter of pipe in millimeters) 4. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 5. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 6. Zinc primer paint is applied at all the welding points prior to finishing. 7. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 8. Foothold made of NB 50mm (G.I.) ‘C’ Class Pipe. 9. Seats made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. 10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 11. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 12. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 14. High tensile steel with galvanized nut bolts are used for assembly. 15. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment.16. Self-Explanatory stainless steel label fixed on equipment for ease of use.Including maintenance cost for 2 years 17 Pull Chair:Providing and fixing Pull Chair in a pair with below specifications:Dimensions (LxWxH): 1950x700x2000mm. Fabricated with main post of NB 100mm (G.I) ‘C’ Class Pipe of approved make. Main frame of NB 50mm (G.I) ‘C’ Class pipe. Handle frame of NB 32mm (G.I) ‘C’ Class pipe.(‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres). All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Handle bars are provided with high end quality rubber grips.Base plate cover made of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and coloured. Seat to be made up from virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, coloured, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. The equipment are fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensile steel with galvanized nut bolts are used for assembly. Equipment made of EN16630 / DIN79000 international standard for outdoor fitness equipment.Self-Explanatory stainless steel label fixed on equipment for ease of use.including maintenance cost for 2 years. 18 Seated Chest Press:Providing and fixing Seated Chest Press in a pair with below specifications:Dimensions (LxWxH): 1800x700x2000mm. Fabricated with main post of NB 100mm (G.I) ‘C’ Class Pipe of approved make. Main frame of NB 50mm (G.I) ‘C’ Class pipe. Handle frame of NB 32mm (G.I) ‘C’ Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres). All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint is applied at all the welding points prior to finishing. Handle bars are provided with high end quality rubber grips.Base plate cover made of virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness, UV resistant and coloured. Seat to be made up from virgin LLDPE plastic by rotational moulding with minimum 4.00mm thickness,coloured, UV resistant and environmental friendly. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. The equipment are fitted with inbuilt limiters to prevent unwanted movements. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensile steel with galvanized nut bolts are used for assembly. Equipment made of EN16630 / DIN79000 international standard for outdoor fitness equipment.Self-Explanatory stainless steel label fixed on equipment for ease of use. ) including maintenance cost for 2 years. 19 Arm wheel: Providing and fixing arm wheel in a pair with below specifications:1. Dimensions (LxWxH): 850 x 800 x 1800 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. Main frame wheel of NB 32mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters).4. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 5. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 6. Zinc primer paint is applied at all the welding points prior to finishing. 7. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 8. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. 9. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 10. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 11. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 12. High tensile steel with galvanized nut bolts are used for assembly. 13. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment.14. Self-Explanatory stainless steel label fixed on equipment for ease of use.Including maintenance cost for 2 years 20 Elliptical Exerciser:Providing and fixing elliptical exerciser with below specifications:1. Dimensions (LXWXH): 1200x540x1600 mm2. Fabricated with main post of NB 100 mm (G.I) ‘C’ Class pipe of approved make.3. Main frame of NB 65 mm (G.I) ‘C’ Class Pipe.4. Handle frame of NB 32 mm and NB 25 mm (G.I) ‘C’ Class Pipe.(NB stands for Nominal Bore Size i.e Internal Diameter of pipe in millimeters).5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints.6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.7. Zinc primer paint is applied at all welding points prior to finishing.8. Handle bars are provided with high end quality rubber grips.9. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00 mm thickness, UV resistant and colored.10. Maintenance free bearings of SKF or equivalent make duly oil sealed M-25 and J shaped welded bolts of 18 mm thickness.11. The equipment is fixed on the ground with concrete of minimum strength M-25 and J shaped welded bolts of 18 mm thickness.12. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.13. High Tensile steel with galvanized nut bolts are used for assembly.14. Equipment made to EN16630/ DIN79000 International standard of outdoor fitness.15. Self-explanatory stainless steel label fixed on equipment for ease of use.Including maintenance cost for 2 years 21 Double cross walker: Providing and fixing double cross walker with below specifications:1. Dimensions (LxWxH): 1600 x 600 x 1600 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. Handle frame of NB 32mm and NB 25mm (G.I.) ‘C’ Class Pipe.(‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters). 4. Foot support frame of 100 x 50 x 2.5mm CRC rectangular pipe. 5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Base plate cover made of virgin LLDPE plastic by rotational molding with minimum 4.00mm thickness, UV resistant and colored. 9. Foothold made of nylon alloy with rounded edges to prevent impact and injury. 10. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 11. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 12. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 13. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover.14. High tensile steel with galvanized nut bolts are used for assembly. 15. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment.16. Self-Explanatory stainless steel label fixed on equipment for ease of use. Including maintenance cost for 2 years 22 Twister: Providing and fixing triple twister with below dimensions:1. Dimensions (LxWxH): 1700 x 1300 x 1300 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. Main frame of NB 32mm (G.I.) ‘C’ Class Pipe.4. Handle frame support of NB 32mm (G.I.) ‘C’ Class Pipe.(‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters).5. Foothold plate of made of cast iron of 12mm thickness. 6. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 7. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 8. Zinc primer paint is applied at all the welding points prior to finishing. 9. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 10. The equipment is fixed on ground with concrete of minimum strength M-25 and Expansion Bolts. 11. Once the concrete is set, the equipment is fixed on to it. 12. High tensile steel with galvanized nut bolts are used for assembly. 13. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment.14. Self-Explanatory stainless steel label fixed on equipment for ease of use.Including maintenance cost for 2 years 23 Rowing machine: Providing and fixing rowing machine with below specifications:1. Dimensions (LxWxH): 1280 x 800 x 1150 mm 2. Fabricated with main post of NB 100mm (G.I.) ‘C’ Class Pipe of approved make.3. Main frame of NB 65mm (G.I.) ‘C’ Class Pipe. 4. Handle support frame of NB 25mm (G.I.) ‘C’ Class Pipe. (‘NB’ stands for Nominal Bore Size i.e., Internal Diameter of pipe in millimeters).5. All Pipes are powder coated with 80-120 micron thick AkzoNobel or equivalent Paints. 6. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. 7. Zinc primer paint is applied at all the welding points prior to finishing. 8. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 9. Foothold made of NB 65mm (G.I.) ‘C’ Class Pipe. 10. Seat to be made up from virgin LLDPE manufactured by rotational molding with 4.00 mm thickness, colored, UV resistant and environmental friendly. 11. Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated are used in the equipment manufactured. 12. The equipment are fitted with inbuilt limiters to prevent unwanted movements. 13. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness. 14. Once the concrete is set, the equipment is fixed on to it and nuts and bolts are covered with base plate cover. 15. High tensile steel with galvanized nut bolts are used for assembly. 16. Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment.17. Self-Explanatory stainless steel label fixed on equipment for ease of use.Including maintenance cost for 2 years 24 Weight Assisted Lat Pull DownProviding, designing and fixing of weight assisted Lat Pull Downfabricated with main pipe of ‘ C’ Class GI Pipe with minimum 75 mm dia and other pipes of 60mm dia and joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Machine to have weight plate adjustment arrangement made of 202 grade stainless steel and designed to prevent theft of weight plates. Plates have to be fully locked in the machine but movable for adjustment. Change system should allow user to freely change resistance by changing individual weight plate of each arm. Weight on each arm should be adjustable between 0-15kgs. Seats to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic as 4.00 mm, colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free, duly oil sealed and self-lubricated made by reputed company to be approved by Engineer in charge. Equipment to be fitted with inbuilt limiters to prevent unwanted movement. All open ends of pipe to be closed by GI/ LLDPE caps or sealed in for user safety. The equipment to be fixed on ground with concrete of minimum strength M-25 and J shape welded bolt made of 18mm galvanized rod and once the concrete is set, fix the equipment on to it. All complete as per direction and approval of Engineer-in-charge regarding material, shape of equipment, colour on metal, seat and base plate and fixing of equipment etc. (the cement concrete and excavation work shall be paid separately).Equipment made to EN16630 / DIN79000 International standard for outdoor fitness equipment.Self-Explanatory stainless steel label fixed on equipment for ease of use. including maintenance cost for 2 years. 25 Sit up station : Providing and fixing Sit up stationin a pair with below specifications:1. Dimensions (LxWxH): 1500 x 1150 x 650mm 12.Fabricated with main frame of NB 100mm (G.I.) C Class Pipe of approved make.3. Main frame of NB 25mm (G.1.) C Class Pipe.4. Leg support of NB 65mm (G.I.) C Class Pipe.NB stands for Nominal Bore l.e., Internal Diameter of pipe in millimeters)5. Perforated MS Sheet for Back Support.6 The back support Fixed on its top is made of perforated MS sheet of 2mm thickness. 7. All pipes are powder coated using Akzo Nobel or equivalent Paint of 80-120 micron thick.8. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs.9. Zinc primer paint is applied at all welding points prior to finishing.10. Base plate cover made of virgin LLDPE plastic by rotational molding with 4.00mm thickness, UV resistant and colored. 11. The equipment is fixed on ground with concrete of minimum strength M-25 and J shaped welded bolts of 18mm thickness.12. Once the concrete is set, the equipment is fixed on to it.13. High tensile steel with galvanized nut bolts are used for assembly.14. Equipment made to EN16630 & DIN 79000 International standard for outdoor fitness equipment.15. Self-Explanatory stainless steel label fixed on equipment for ease of use.Including maintenance cost for 2 years 26 Deduct for taking away the old gym equipment without dismembering i/e dismantling charges and removing the dismantled old gym eqipment from the site assumiing 25% of the cost as buy back value as per the direction of engineer-in-Charge.(i) Air Walker 27 (ii)Air Swing 28 (iii) Horse Rider Station 29 (iv) Stair Stepper 30 (v) Leg press 31 (vi) Pull chair 32 (vii) Seated chest press 33 (viii)Arm wheel 34 (ix) Elliptical exerciser 35 (x) Double cross walker 36 (xi) Twister 37 (xii) Rowing machine 38 (xiii) Weight Assisted lat pull down 39 (xiv) Sit up station 40 SCHEDULE CMaintenance cost for 5 years ( 02 year free + 03 year paid) for 3rd year all item of schedule Bitem no. 12 to 25 assuming at 2% of all itemsof Schedule B i.e. Rs. 7,89,976/- (each set) 41 for 4th year all item of schedule Bitem no. 12 to 25 assuming at 3% of all itemsof Schedule B i.e. Rs. 7,89,976/- (each set) 42 for 5th year all item of schedule Bitem no. 12 to 25 assuming at 4% of all itemsof Schedule B i.e. Rs. 7,89,976/- (each set) 43 Total 44 Less correction on factor on DSR 2023 on account of GST @ 0.973
