E -Tender For The Furnishing Work At Ernakulam- 1 e -Tender for the furnishing work at ErnakulamFor more details refer tender documents 2 12.45.3 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturers specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum moisture resistant board50cm. 3 Providing and fixing partition using 12.5 mm thick tapered edge gypsum moisture resistant board up to ceiling height (upto 360cm) consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufactures specification and direction of engineer in charge all complete.75 mm overall thickness partition with 12.5 mm thick Moisture Resistant Board 4 12.52.4 Providing and fixing tiled false ceiling of approved materials of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams per sqm, both side inclusive) consisting of main T runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200mm center to center and cross T of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main T at 600 mm center to center to form a grid of 1200x600 mm and secondary cross T of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main T runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85x 30x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer -in-charge.12.5 mm thick fully Perforated Gypsum Board tile made from plaster board having glass fibre conforming to IS: 2095 Part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with centre borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side , having as NRC ( Noise Reduction Co efficient) of 0.79, with 50 mm resin bonded glass wool backing. 5 26.22.1 Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991,in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main- T runners of size 24x38 mm of length 3000 mm, cross - T of size 24x32 mm of length 1200 mm and secondary intermediate cross-T of size 24x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.With 15 mm thick tegular edged light weight calcium silicate false ceiling tiles. 6 15.7.4Demolishing brick work manually / by mechanical means including stacking of serviceable material anddisposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.Incement mortar 7 15.3Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge. 8 13.1.112 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) 9 13.43.1Applying one coat of water thinnable cement primer of approved brand and manufacture on wall/ceilingsurface: Water thinnable cement primer 10 13.60.1Wall/ceiling painting with acrylic emulsion paint of approved brand and manufacture to give an even shade: Twoor more coats on new work 11 13.80Providing and applying white cement-based putty of average thickness 1 mm, of approved brand andmanufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 12 13.45.1 Finishing walls with textured exterior paint of required shade:New work (Two or more coats applied @ 3.28 ltr/ 10 sqm ) over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm 13 Toughened Glass Partition Providirig and fixing 12mm Thick Clear toughened Glassy using Dorma patch fittings, all complete as per architectural drawings and the directions of Engineer 14 Toughened glass door :Providing fixing door of 12mm thick Toughened glass door ( Saint gobain) with Dorma/ozone) patch fiiitngs ( floor spring,Top patch ,pivot Pin ,Bottom patch ,Corner 15 ReceptionWall, Conference room& CEO room WallPaneling for the existing surfaces to be made out of 16 mm thick marine plywood framework /aluminum section frame work backing covered with 9/12 mm thick 303 grade marine ply wood finished with approved 1.0mm thk laminateincluding skirting & band at top in the same alignment with a groove and including molding of approved size as shown in detailed drawing or as directed by Architect 16 Wooden wall partition-wall partition behind the reception area by using 6mm and 9mm thick bwr plywood laminated with veneer with approved design and pattern 17 Interior landscaping Providing 25mm to35mm white marble pebbles stone, round polished white pebble with plants 18 Window Blinds:Providing and fixing window blinds on each window including cost & conveyance all materials & labour etc. Except pantry area 19 Wall paper:- Providing & fixing wall paper, of approved shade & design,basic price to be minimum Rs1200/- per sq.m finished complete asdirected. 20 Sticker work : Applying&Fixingetchingstickerforaglass partition & Glass Door including all Materials & Labour Charges 21 Workstations: Fabrication, supply and installation at office type modular workstations ; Leg and beam desk system of following specification and size. Table top: 18mm thick MDF and 2mm edge banding finish, access flapwire manager: Understructure: Made of ERW tubular structure of size 50x50mm 1.6 mm thick powder coated with suitable levelers; power beam for integrated wire management, raceways, Raceway:Data and power with provision for sockets/data below table top [20.01 to 22.01]4 seater workstationCross model (2400 x 2400 x 750 H) 22 6 seater work station discussion Table(2400 x 1200 x 750 H) 23 2 seater workstation (2400 x 600 x 750 H) 24 L Shaped executive table of size (1800 x 900 x 750 H + 900 x 400 x 750 H )with storages & drawers with lock ,keyboard drawer using 18mm thick MDF with 1 mm lamination and 2mm edge banding finish, includingcost & conveyance all materials & labour etc 25 Reception Table (3500 x 600 x 750 H) with side storage (900 x 450 x 750 H) Providing & Fixing Reception Table as per design and size. Made up of 16 mm thick 303 grade bwr marine plywood with 1 mm lamination and 2mm edge banding finish 26 CEO Table (2400 x 1200 x 750 H) with side storage (1000 x 400 x 750 H) Providing & Fixing CEO Table as per design and size .Made up of 18mm thick 303 bwr grade marine plywood with 1 mm lamination and 2mm edge banding finish 27 Meeting table (3600 x 1200 x 750 H ) : Laminate finish Table top made of 18mm thick pre laminated mdf with 1 mm laminationfinishchamphered edge having matching shade of edge banding. Table top to have aluminum finish flip top and provision to fix power and data inside a dual layered fixed tray under the table top. To be inclusive of under table top mountedadjustable size and cable manager of full extended table height length. Either table Legs shall be made from MS50 micron powder coated Legs assembled together MS Powder coated plate at topor the vertical support shall be provided with 18 mm Prelaminated mdf as per the design.The base support plate is having provision for wire entry and glide fixing. The wire carrying is facilitated through the hollow space between two leg extrusions and the wires are concealed between removable rigid PVC extrusion in the leg . 28 Conference Table:Size : 9000mm L x 1400 mm D x 750mm Ht. Laminate finish Table top made of 18mm thick pre laminated mdf with 1 mm laminationfinishchamphered edge having matching shade of edgebanding. Table top to have aluminum finish flip top and provision to fix power and data inside a dual layered fixed tray under the table top. To be inclusive of undertable top mountedadjustable size and cable manager of full extended table height length. Either table Legs shall be made from MS50 micron powder coated Legs assembeled together MS Powder coated plate at topor the vertical support shall be provided with 18 mm Prelaminated mdf as per the design . The base support is having provision for wire entry and glide fixing. The wire carrying is facilitated through the hollow space between two leg extrusions and the wires are concealed between removable rigid PVC extrusion in the leg . 29 Hi backchairs for CEO & conference table with ergonomic design, good lumbar support, seating comfort, Seat with high density PU foam upholstered with approved quality fire retardant fabric, Hydrualic gas lifting mechanism, Tilt locking mechanism, fixed armrest with integral PU skin metal inserted arm rests, five pronged chrome base with nylon castors.(for CEO) 30 Hi backExecutive chairs for officers with ergonomic design, good lumbar support, seating comfort, Seat with high density PU foam upholstered with approved quality fire retardant fabric, Hydrualic gas lifting mechanism, Tilt locking mechanism, fixed armrest with integral PU skin metal inserted arm rests, five pronged chrome base with nylon castors.(for cabin) 31 Medium back mesh chairs for conferance table, with ergonomic design, good lumbar support, seating comfort, Seat with high density PU foam upholstered with approved quality fire retardant fabric, Hydrualic gas lifting mechanism, fixed armrest with integral PU skin metal inserted arm rests, five pronged chrome base with nylon castors. 32 Medium back task mesh chairs for workstationswith ergonomic design, good lumbar support, seating comfort, Seat with high density PU foam upholstered with approved quality fire retardant fabric, mesh back, Hydrualic gas lifting mechanism,fixed armrest with integral PU skin metal inserted arm rests, five pronged chrome base with nylon castors. 33 Metal type leg VisitorschairFixed armrest withFabric Seat ,Large chrome plated heavy duty metal base Cantilever base Stylish black nylon mesh/cushioned backrest 34 Plant box1200 x 300 x 750 H :15mm multiwood with PU paint finish 35 2 seater visitors sofausing good quality timber with Comfort Level - Medium Form andHigh Quality 230 GSM Polyester Fabric good quality fabrics 36 Discussion Table with 2 nos fabric couch 37 Discussion Table with 3 nos fabric couch 38 Flush door : Providing and fixing 30 mm thicklaminated flush door shutters conforming to Idecorative type, core of block board construction with frame of I st class hard wood and well matched mica on both faces of shutters.including Stainless Steel butt hinges ,handle ,lock with necessary screws etc 39 Modular pantry unit using high quality 710 Gurjen prelaminated plywood including storages, tracks, drawersincludingcost & conveyance all materials & labour etc. 40 Storage unit of approved make of following size made of 12/18mm thick Pre laminated medium density fiber board for vertical and horizontals and intermediate shelves. The openable door shutters shall be provided with SS handles, locks, auto closing hinges and necessary hardwares etc; complete. The exposed edges shall be finished with 2mm thick PVC lippingSize : 750cm L x 210cm H x 400cm D 41 Wash counter storage unitof approved make of following size made of 16 mm thick both sides plywoodboards for vertical and horizontals and intermediate shelves. The openable door shutters shall be provided with SS handles, locks, auto closing hinges and necessary hardwares etc; complete. The exposed edges shall be finished with 2mm thick PVC lipping 42 Granite topProviding and fixing 12 mm thick granite with edge moldingExtra for providing opening or required size & shapefor wash basin/kitchen sink pantry-1.98 sqmwash counter - 0.63 sqm 43 Pedestal Storage: made of 18mm pre- laminated MDF. All exposed edges lipped with 2mm or 0.8mm edge band. One Pull out drawer and one shutter door Considered.Size: 500H X 420D X 400 W mm 44 6 Watt LED ceiling lightInstallation, Testing and Commissioning of 6 W, Surface / Recess mounted LED Dowlight Luminaire including driver complete asrequired. Brand - Wipro /Philps 45 3 Watt LED ceiling light Installation, Testing and Commissioning of 3 W, Surface / Recess mounted LED Dowlight Luminaire including driver complete asrequired. Brand - Wipro /Philps 46 LED Strip Light : Installation, Testing and Commissioning of Linear LED Strip-lights(15 Watt /Metre) for installing in False-ceiling Coves together withrequisite driver etc. complete as required. with 2 years Warrantyagainst any manufacturing defect working under standardelectrical condition. 47 Supply and installation of Interactive display unit with accessories: of size 86 in built Intel core i5 8gb 512 with windows10th or 11 with two year warranty Display parameter: ADS/1897(H)x1068(V)/16:9/450cd/M2/1400:1/6˜8ms/DLED/178 (V) 178(h)/3840(h)x2160(v)20Wx2 sound track2.0 /amlogic T982 quad core a55x4.19ghz /mil G52mp2Android space: Android 11.0/ram 4 GB/Rom32GB/version 5.0 /frequency 2.4Ghz distance 0.10mWarless Module: Version 802.11ac.b/g/n/a/ax/frequency 2.4Ghz/5Ghz,distance -0-10mHDMI in -/USB2.01/usb 3.0 1/touch usb 2.2 1/audio in 1/audio out 1/i/o interface : coaxial output 1/Earphone 1/RS232 1/RJ45 1/3” usb 3.0+type +c+touch out+HDMI in window cpu-intel i3/i5/i7/system version-win 10pro/11pro/internal storage -4Gb/8GB/16Gb/32GB/OPS computer -HDD-ssd-128/256/512Gb/Graphics -integrated/wifi-yes/PC interface-VGA x HDMI x wifi xLAN x lcommic-in lan LINE OUT USB 2.0 5USB 3.0I/power dissipation -440w standby consumption 0.5w/power suppy-100-240v-50/60Hz4AOthers : VESA Hole specification -800x400mm/wall mounting screws spec -M8x25mm/net weight -70kg/Touch screen-Teach technology -Non contact infrared sensing technology/writing height-3mm/bounding 0 boundingAccessories- writing display-Double stylus pen two color/wall brocket -1pc/touch pen-1pc/power cable-1pc/operation manual-1Environmental – working temperature -0.40cParameters- storage temperature-20+60c/working life-time -60000hrs 48 Blue Star/voltas or equilant Make Ceiling Mounted Duct ableUnitSupply of Blue Star/ voltas or equilant make 4 TR Inverter Cassette Split air conditioner 1PH Model AC with cordless remote (ID336TANU1) FullCopper Mode 49 Supply of Blue Star /voltas or equilant make Air-cooled Concealed Split air conditioner with nominal capacity 1.5TR Fitted with Rotary compressor and Microcontroller panel 50 LOW SIDE 1 [49.01 to 51.01]1. Installation, Testing & Commissioninga. 4TR Cassette Installation, Testing &Commissioning 51 b. Copper refrigerant piping interconnecting the condensing unit to evaporating unit 52 c. Installation, testing and commissioning of the entire system after necessary leaktest,Vaccumazing and charging 53 LOW SIDE 22. Supply & erection of GSS Ducting (Supply Air) 22G 54 LOW SIDE 3Supply and installation of Supply & Return AirGrills control damper 55 LOW SIDE 4Supply and installation of Supply & Return AirGrills control damper 56 LOW SIDE 5Supports for duct and machine (Slotted anglethreaded rod etc..) 57 LOW SIDE 6ODU Stand for Cassette condensing units. 58 LOW SIDE 7Machine Supporting rubber pads as vibrationisolators 59 LOW SIDE 8Drain water piping, 32mm PVC with RubberSleeve insulation. 60 LOW SIDE 9Canvass connection 61 LOW SIDE 10ODUStandfor1.5TRcondensingunits
