Bids Are Invited For Estimate For Procurement Of Furniture In The Prefabrictaed Classrooms-1 Providing And Placing Of Spine Based Modular Workstations Supplying & Placing Workstation In Completely Knock Down Conditions With Per Seat Size 750Mm X 600Mm X, Samba-Jammu And Kashmir

Bids Are Invited For Estimate for procurement of Furniture in the Prefabrictaed Classrooms-1 Providing and Placing of Spine Based Modular Workstations Supplying & Placing workstation in completely knock down conditions with per seat size 750mm X 600mm X 1200mm that is to be assembled at site. The top shall be made up of 25mm thick Pre-laminated particle board with approved laminate and finish as per approved shade. The profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine. A pullout keyboard tray shall be provided of 18mm thick Pre-laminated particle board. The tray shall be operated on keyboard channel. The table shall have panel based partition system of 60mm thick & 1200 mm height with framework made of Aluminium alloy extrusions. All Aluminium parts shall be pretreated and duly powder coated of 40-60µ thick. All these frame work sections shall be fitted to each other by fasteners of 2mm thickness which is properly zinc coated for corrosion resistant. Raceway shall be provided of aluminum 118mm height below the work top as per requirement for inlaying of electrical management and carrying the wire horizontally. The exposed vertical and horizontal faces of the frames shall be snap fitted with curve trims. The trims shall be made of aluminum extrusions of size 60x19mm with 1.5mm thick and covered with Die Casted End caps on joints, 2 way, 3way & 4 Way caps. The Partition shall have concealed wire management capabilities for responsive and safe operations of power, telecommunications and data (LAN) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. Slots/cutouts shall be given on raceways to fix all electrical and data points. The Partition shall be in fabric pinup board. The table top shall be supported on metal base powder coated loop legs having cross-section area 40mm X 20mm. There shall be shoe provided at the bottom of the leg to avoid the scratches on the floor. Dimensions Tolerance + 20 mm each 240 2 Providing and placing of Cushioned High Back Chair with ergonomic design, comfortable & aesthetically appealing.The seat shall be made up of 12mm thick hot-pressed plywood and moulded seat foam upholstered with Micro fabric. Seat size shall be 450 mm (L) x 470 mm (W). Backrest & seat shall be provided with PPCP Cover. Back shall also be upholstered with fabric. Backrest size shall be 700 mm (H) x 470 mm (W). The foam used in the seat shall have density of 40 – 50 Kg/m3 & Hardness of 13 – 17 Kgf (tolerance +/- 5%). The Armrest shall have adjustable feature so that it can be moved up & down. The arm rest shall be made up of injection Moulded polypropylene. The size of the Arm rest shall be 160 mm (L) x 320 mm (H). The twin wheel castors used shall be injection Moulded in Nylon and shall have diameter of 50 mm. The chair shall have Single point locking synchro tilt mechanism with one lever control for locking and seat height adjustment. Mechanism shall be made of MS plate of thickness is 1.3 mm and tilting angle should be 30 degrees. The mechanism shall have knob to adjust the back tilt tension. The base of the chair shall be injection Moulded Nylon and fitted with 5 no’s twin wheel castors. The base should have 630 pitch circle diameter. The Chair shall be tested for ANSI/BIFMA standard from BIFMA Certified Laboratories within India. Dimensions Tolerance + 20 mm each 240 Estimate for procurement of Furniture in the Prefabrictaed Classrooms FACULTY FURNITURE 3 Providing and placing of Mesh Fabric High Back chair with ergonomic design, comfortable & aesthetically appealing. The seat shall be made of 18mm thick hot pressed commercial plywood upholstered with foam net tapestry 0.9mm thick and 300 GSM and the back shall be made of injection moulded polypropylene net cover upholstered with breathable mesh tapestry. The backrest of the chair shall be made by keeping the natural curvature of the spine with adjustable lumbar support as well as adjustable headrest. The chair shall be supplied With 2-Way Adjustable PU Arm which is completely joint with seat. For seating durability the chair shall have knee tilt 360 degree revolving mechanism having Single position locking and tilt tension adjustment with anti-shock feature. The pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm to suit them using the lever under the seat. The pedestal should have five legged injection moulded in 30% glass filled black nylon having pitch circle Dia. 700 mm fitted with 5 nos. twin wheel castors. The castors of the chair should beinjection moulded in 30% glass filled nylon. The seat size shall be 465±10 mm(W) X 500±10 mm(D) and back size shall be 780±10 mm(H) from seat & overall height = 1245±10 mm. Dimensions Tolerance + 20 mm each 8 4 Providing and placing of Main Table with overall size of table shall be 1500 Width mm X 750 Depth mm X 740 Height mm that is to be assembled at site. The construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. The work top shall have the size 1500mm X 750mm made up of 25mm thick particle board of grade II of IS 12823 with approved laminate and finish as per approved shade. The table top profile shall be in rectangle shape with front and back full round post form and other edges shall be sealed with 2mm thick thin strip of impermeable PVC that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree Celsius. The table top shall be supported over particle board base gable end. The end wall of the table on the side shall be topped by gable end. The gable end shall be made up of 25mm thick particle board and profile shall be in linear shape with front and back full round post form and other edge with appropriate PVC edge banding. The table shall be clad with 18mm thick modesty panel which provide structural support for the table. It should be 18mm thick pre-laminated particle board with appropriate PVC edge banding connected with both end. There shall be buffers provided at the base to avoid scratches on the floor. The table shall be supplied with side unit with an overall size 1050mm X 450mm X 710mm. The side unit shall be made up of Pre-laminated particle board of grade II of IS 12823 with top 25mm thick and other parts 18mm thick. A mobile pedestal shall be provided with an overall size 400mm X 450mm X 660mm. The pedestal shall be made up of Pre-laminated particle board of grade II of IS 12823. Pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. The pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. The drawer shall be operated with SS handle and easily close & open with the assistance of roller channel and ball bearing channel having to enable smooth operation. The drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. The pedestal shall be mounted over 50mm injection moulded nylon castor. Dimensions Tolerance + 20 mm each 8 5 Providing and placing of Mesh Visitor chair with overall dimensions of seat shall be 47.0 CM (W) x 48.0 cm (D). The seat shall be made of 18mm thick hot pressed commercial plywood upholstered with high resilience moulded polyurethane foam 50mm thick having density 40kg/m³ with foam net tapestry 0.9mm thick and 300 GSM and the back shall be made of injection moulded polypropylene net cover upholstered with breathable mesh tapestry. The backrest of the chair shall be made by keeping the natural curvature of the spine with adjustable lumbar support. The chair shall be supplied with injection moulded polypropylene fixed arm completely joint with seat. The frame structure shall be cantilever support type made of MS CRCA chrome plated round pipe of dia. 25.4mm with 2mm thick. The seat size shall be 465±10 mm(W) X 500±10 mm(D) and back size shall be 555±10 mm(H) from seat & overall height = 960±10 mm. Dimensions Tolerance + 20 mm each 24 6 Providing and placing of Glass Door Almirah with overall size of the Almirah shall be 916mm (W) X 486mm (D) X 1980mm (H). The Almirah shall be supplied with 2 nos. of glass doors with 4 nos. of adjustable shelves i.e. 5 loading compartments. The glass used shall be 4mm thick clear. The shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. Uniformly distributed load capacity of each shelf shall be 40 Kg maximum. Each rack shall be provided with stiffener at bottom for strength. The entire body panel and shelf shall be made of high yield strength 0.8mm thick and door 1mm thick CRCA sheet of grade ‘D’ confirming to IS: 513. The complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40-50µ thick. Dimensions Tolerance + 20 mm each 8 CLASSROOM FURNITURE 7 Providing and Placing in position of the following specifications of 2-Seater Desk Cum Bench shall be Overall depth of Desk cum Bench shall be 1025, Width of Desk & Bench 1200, Depth of Desk 385, Depth of Bench 330, Height 750 & Height of Bench 450. PANELS: -Seat, Desk & Shelf shall be of 25 thk PLB with 2 thk PVC lipping all around. Back shall be of 18 thk PLT with 2 thk PVC lipping all around. UNDERSTRUCTURE: - Side frames are made of Obround tube 60 X 30 X 2.0 thk and for holding cross member CRCA 2.0 thk bracket welded to vertical member. Base shall be HR plate 8.0 thk welded to the vertical member. Two triangular brackets welded to the vertical member vshall beible from side, will support desk and shelf. One Extra gusset support of 2.0 mm thk plate provided from side. Cross members are Rect. tube 50.8 X 25.4 X 1.6 thk. & Rect. 80 X 40 X 1.6 thk tube. For seat holding, bracket of HR 5.0 thk welded to cross members for holding seat. Perforated Modesty as shown shall be of CRCA 0.8 thk. For additional support, hat section of CRCA 0.8 thk welded inside modesty. The obround tubes are closed with metal caps. The product shall be knockdown structure, to be assembled at site using machine screws. Complete metal structure shall be powder coated each. Dimensions Tolerance + 20 mm 8 Providing and Placing in position of the following specifications of 3-Seater Desk Cum Bench shall be Overall depth of Desk cum Bench shall be 1025, Width of Desk & Bench 1600, Depth of Desk 385, Depth of Bench 330, Height of Desk 750 & Height of Bench 450. PANELS: -Seat, Desk & Shelf shall be of 25 thk PLB with 2 thk PVC lipping all around. Back shall be of 18 thk PLT with 2 thk PVC lipping all around. UNDERSTRUCTURE: - Side frames are made of Obround tube 60 X 30 X 2.0 thk and for holding cross member crca 2.0 thk bracket welded to vertical member. Base shall be HR plate 8.0 thk welded to the vertical member. Two triangular brackets welded to the vertical member vshall beible from side, will support desk and shelf. One Extra gusset support of 2.0 mm thk plate provided from side. Cross members are Rect. tube 50.8 X 25.4 X 1.6 thk. & Rect. 80 X 40 X 1.6 thk tube. For seat holding, bracket of HR 5.0 thk welded to cross members for holding seat. Perforated Modesty as shown shall be of crca 0.8 thk. For additional support, hat section of crca 0.8 thk welded inside modesty. The obround tubes are closed with metal caps. The product shall be knockdown structure, to be assembled at site using machine screws. Complete metal structure shall be powder coated each. Dimensions Tolerance + 20 mm Total Quantity : 552

Sr No	CorrigendumDate	Corrigendum	CorrigendumType	NewSubmissionDate
1	22-11-2024			28-11-2024
2	22-11-2024			28-11-2024

Refer document

INR 280000.0 /-

Refer document