Tender For Raghuagarad To Marthapur Road For The Year 2024-25 - Clearing And Grubbing Road Land Including Uprooting Rank Vegetation, Grass, Bushes, Shrubs, Saplings And Trees Girth Up To 300 Mm, Removal Of Stumps Of Trees Cut Earlier And Disposal Of Unser

Sharing tender

Raghuagarad to Marthapur Road for the Year 2024-25 - Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, up to a lead of 1000 meters including removal and disposal of top organic soil not exceeding 150 mm in thicknessas per direction of Engineer-in-Charge. 2 Earth work inexcavation of foundation in all kinds of soil within initial leads and lift including rough dressing ,leveling bed and depositing the excavated materials away from the working area etc. complete 3 Construction of granular sub-base by providing Close graded Granular subbase Grading-III material as per table 400-1, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density complete as per Clause 401 of MoSRT&H Specifications for Road & Bridge works (4th Revision) 4 Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing thematerial with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, layingin uniform layers 5 Labour for scraping cleaning the road surface applying tack coat using 3.0kg of Bitumen for 10 sqm and laying 37.5mm thick built up spray groutingin one layer 0.45 cum tof 25mm to 40mm size hard granite, Page-152,Item no-28 6 Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including clearing of road surface and spraying primer at the rate of 0.60 kg/sqm with mechanical/manual broom clause 502 of MoSRT&H specifications for road & bridge works.(4th Revision) etc. complete as per direction of Engineer-in-charge. (4th revision).A/R,Page-167,Item no-43 7 Providing and applying tack coat with Bitumen emulsion(MS)using emulsion distributor at the rate of 0.20 kg/sqm on the prepared bituminous surfaces cleaned with mechanical broom includingcost, conveyance, royalty, taxes, labour charges, T&P etc. required for the work complete as perdirection of the Engineer-in-Charge. 8 Providing and laying bituminous macadam with hot mix plant using crushed aggregates of specified grading premixed with bituminous binder of 60/70 penetration grade of bitumen, transported to site, laid over a previously prepared surface with a hydrostatic paver finisher with sensor control to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per Clause 504 of MoSRT&H Specifications for Road & Bridge works (4th Revision) A/R,Page-169,Item no-45 9 Providing and laying semi dense bituminous concrete with batch type hot mix plantusingcrushedaggregates of 13mm nominal size (Grading-I) premixed with bituminousbinder ofVG-30 ofbitumen,transportingthehot mixtoworksite, laying with a hydrostaticpaverfinisherwithsensor control to the required grade, level and alignment, rolling with smooth wheelede,vibratory and tandem rollers to achieve the desired compaction includingcost, conveyance, royalty, taxes, labour charges, T&P etc. required for the work complete as perdirection of the Engineer-in-Charge. 10 Construction of embankment with approved material obtained from borrow pitswith all lifts & leads transporting to site by mechanical means (within a lead of 5Km)spreading, grading to required slope and compacting to meet requirement of Tables 300-2 & Clause 305 of MoSRT&H specifications for road and bridge works (4th revision)andas per direction of the Engineer-in-Charge. 11 Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.