Tender For Misc B/R Repair To Certain Accn At Af Stn Adampur- 1 BR WORKS :- 2 M&L for Reinforced cement concrete, type B-1, (1:2:4), using 20 mm graded crushed stone aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, and in shelves and the like complete all as specified and directed. 3 M&L for Reinforced Cement concrete, type B-1 (1:2:4), using 20 mm graded crushed stone aggregates as in lintels up to 1.5 metre clear span, bed blocks, copings and the like including weathering, slightly rounded or chamfered angles & throating including provision of necessary formwork, complete all as specified and directed. 4 M&L for Brick work using bricks as specified in PS clause 5.1, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar (1:6), complete all as specified and directed. 5 M&L for Brick work in half brick thick wall using bricks as specified in PS clause 5.1, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar (1:4), complete all as specified and directed. 6 Use & waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizontal or sloping) with fair finished flat surfaces of concrete, complete all as specified and directed. 7 Use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. with rough finished surfaces of concrete, complete all specified and directed. 8 M&L for Plywood 6 mm thick, 5 ply type BBcommercial BWR one side laminate confirming to IS: 303 fixed on frame, IN REPAIRS, complete all specified and directed. 9 M&L for Plywood 12 mm thick, 7 ply type BBcommercial BWR one side laminate confirming to IS: 303 fixed on frame, IN REPAIRS, complete all as specified and directed. 10 M&L for Plywood 18 mm thick, 12 ply type BBcommercial BWR one side laminate confirming to IS: 303 fixed on frame, IN REPAIRS, complete all as specified and directed.. 11 S&F, Stainless steel 100mm size auto soft closing hydraulic hinges fixed with stainless steel screws, ISI marked complete all as specified and directed. 12 S&F, Mild steel chromium plated solid handle, 100mm suitable for cupboard shutter, complete all as specified and directed. 13 M&L for Rolled mild steel sections as in joist channel, angle, post, strut or Tee section, fixed independently, with base plate, connecting plates (cut to ordinary length i.e within 20mm of length indicated) quality A confirming to grade Fe-410-Gde E-250, complete all as specified and directed. 14 M&L forRolled mild steel work as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting platesconformingto IS 1161-1979 grade St -240 complete all as specified. quality-A complete all as specified and directed. 15 M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 16 S&F, Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm of any colour hving tensile strength of 550 Mpa as in roof coverng/ cladding to wall bent to curve, fixed with self tapping screws comlete all as specified. 17 S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm of any colour hving tensile strength of 550 Mpa as in roof coverng/ cladding to wall, fixed with self tapping screws comlete all as specified. 18 Water Proofing Treatment to RCC roofs comprising of : - 19 Taking down existing water proofingtreatment (any no. of layers) from RCC roofs includingcleaning the surface including flashings and junction of parapet etc. with wire brushing & water to the entire satisfaction of EIC, complete all as specified and directed. 20 M&L for PCC (1:2:4) type B-1 using 20 mm graded stone crushed aggregate, laid to slope as directed by Engineer in Charge over RCC roofs as padding, complete all as specified and directed. 21 M&L for Rendering15 mm thick (Average thickness) rendering on roof surface including flashings and junction of parapets etc., finished even and fairin cement mortar (1:4), using water proofing compound as recommended by manufacturers after brushing cement slurry @ 1.20 kg/Sq. m, complete all as specified and directed. NOTE: Supply only WPC will be measured & paid for separately under respective item of BOQ. 22 M&L for APP based polymeric membrane laid on primed roofs & flashing by forced application using Butane torch and sealing all joints on primed surface by applying hot blown industrial grade bitumen @ 85/25 @ 1.20 kg/Sq.m over a coat of bitumenous primer @ 0.40 litre per square metre over clean RCC/plastered roof surfaces & flashings complete all as specified and directed. 23 40 mm thick brick tiles (EXCEPT TILES) bedded over 15 mm thick cement mortar (1:4),and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement on APP membrane complete all as specified and directed. 24 M&L for 40 mm thick brick tilesbedded over 15 mm thick cement mortar (1:4),and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement on APP membrane complete all as specified and directed. 25 M&L for Making benching with PCC (1:2:4) type B-0 (using water proofing compound) along side walls adjoining to roofs, in CONCAVE SHAPE,complete all as specified and directed. NOTES: (i)WPC will be measured and paid for separately under respective item of BoQ.(ii) For Performance Guarantee of Water Proofing Treatmentrefer PS clause 11.5. 26 Supply only water proofing compound (WPC), ISI marked. 27 M&L for Decorative laminates type I, 0.5 mm thick of surface finish, colour and pattern as approved , fixed with approved adhesive complete all as specified and directed. 28 M&L for Decorative laminates type I, 0.9-1 mm thick of surface finish, colour and pattern as approved , fixed with approved adhesive complete all as specified and directed. 29 M&L for High quality solid colour (matching shade) PVC edge banding tape not less the 3 mm thick having 18/19 mm widthfixed with approved adhesive to HDMR board complete all as specified and directed. 30 S&F, Ball bearing runners 45mm telescopic channel (20 inch) full extension load capacity 50 kgs complete all as specified and directed. 31 S&F, Chrome plated stainless steel wire basket (storage basket) pull out type for large utensills, size 486x500mm with necessary fixing clips etc.complete in all respect complete all as specified and directed 32 S&F, Chrome plated stainless steel wire basket (cup and soucer basket) pull out type, size 530x500mm with necessary fixing clips etc. complete all as specified and directed 33 S&F, Chrome plated stainless steel wire basket (jar basket) pull out type, size 536x500mm with necessary fixing clips etc. complete all as specified and directed. 34 S&F, Chrome plated stainless steel wire basket (Thali basket) pull out type,size 380x500 mm with necessary fixing clips etc. complete all as specified and directed 35 S&F, Chrome plated stainless steel wire basket pull (cutlery basket) out type,size 380x500 mm with necessary fixing clips etc. complete all as specified and directed 36 S&F, Chrome plated stainless steel wire basket pull (storage/plain basket) out type,size 380x500 mm with necessary s fixing clips etc. complete all as specified and directed 37 Chrome plated stainless steel wire basket pull (Bottle pull out) out type,size 150 to 200 mm with necessary sliding frame structure, fixing clips etc. complete in all respect as specified and directed. 38 S&F, 8 Ltr PVC water basket complete all as specified and directed. 39 M&L for 25 mm thick, cement concrete type B-0, 1:2:4 using 12.5 mm graded crushed stone aggregate, finished even & rough, as in sub floors, complete all as specified and directed. 40 M&L for Granite jet black shade, 15-18 mm thick,as in step, jambs, cooking platform and like, machine cut, machine polished,bedded and jointed with grey cement slurry & pointed with grout of matching shade including necessary cutting over & including 10 mm thick (average thickness) cement mortar (1:4), complete all as specified and directed. 41 Rounding of/ moulding to edges (half round) of stone of any description including rubbing and polishing (Granite finish), complete all as specified and directed. 42 M&L for Glazed ceramic coloured tiles 7mm thick,area of each tile exc. 0.17 Sq.m but n. exc. 0.19 Sq.m on vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 10 mm thick bedding layer in cement mortar (1:4), complete all as specified and directed. 43 M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exc. 0.11 Sq.m but n. exc. 0.18 Sq.m,laid in floors etc, set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 15 mm thick bedding layer in cement mortar (1:4), complete all as specified and directed. 44 M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exc. 0.11 Sq.m but n. exc. 0.18 Sq.m,laid in skirting, dado etc, set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over andincluding 10 mm thick bedding layer in cement mortar (1:4), complete all as specified and directed. 45 M&L for Rendering 15 mm thickon fair faces of brick work or concrete surfaces, finished even and fairon walls in cement mortar (1:6)complete all as specified and directed. 46 M&L for Rendering 15 mm thickon fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:4), mixed with water proofing compound as per manufacturers instructions, complete all as specified and directed.NOTE: WPC will be measured and paid for separately under respective item of BoQ. 47 M&L for Prepration of new plasterd wall surfaces of any description complete all as specified and applying the following: -(a) Applying wall care putty, in two coats& smoothening the surfaces as specified. (preparatory to paint as directed).(b) Two coats of interior acrylic distemper/oil bound distemper over and including a coat of interior primer. 48 M&L for Complete removal of existing treatment of any description, including prepration of wall surfaces of any description complete all as specified and directed and applying the following: -(a) Applying wall care putty, in two coats& smoothening the surfaces etc. as specified (preparatory to paint as directed). (b) Two coats of interior acrylic distemper/oil bound distemper over and including a coat of interior primer. 49 M&L for Prepration of new plasterd wall surfaces of any description complete all as specified and applying the following: -a) Applying wall care putty, in two coats& smoothening the surfaces as specified. (preparatory to paint as directed).complete all as specified. (b) Two coats of exterior acrylic emulson over and including a coat of water based exterior primer complete all as specified and directed. 50 M&L for Two coatsof synthetic enamel paint over & including a coat of red oxide primer over steel or iron surfaces of any description not other wise described over 10cm width or girth including preparation of surfaces, complete all as specified and directed. 51 Disconnecting existing tanks of capacity exceeding 500 litre but not exceeding 1000 litre, setting aside (or lowering if required) for cleaning/roof repair etc. and hoisting, reconnecting and re-fixing in position after necessary cleaningby removing all scale and dirt etc. including cleaning mouth of circulating service pipescomplete all as specified and directed 52 S&F, 500 litre capacity, white, three layered polyethylene water storage tanks (cylindrical vertical with threaded lid) including hoisted and fixed in position, making connections, IN REPAIRS, including the following acessories complete all as specified & directed: -(i) Gun metal ball valves, high pressure, with metal rod & high density plastic ball complete screwed for iron pipe or brass ferrule and fixed, IN REPAIRS, suitable for 20 mm bore GI pipe(iii) Gun-metal stop valve (quarter turn type)with MS lever handle, suitable for 20 mm bore GI tubes, ISI marked, screwed both ends for iron pipe, IN REPAIRS.(iv) Provn of 20 mm bore GI light grade tube from O/H tank to nearest mouth of RWP, IN REPAIRS. 53 S&F, 1000 litre capacity, white, three layered polyethylene water storage tanks (cylindrical vertical with threaded lid) including hoisted and fixed in position, making connections, IN REPAIRS, including the following acessories complete all as specified & directed: -(i) Gun metal ball valves, high pressure, with metal rod & high density plastic ball complete screwed for iron pipe or brass ferrule and fixed, IN REPAIRS, suitable for 20 mm bore GI pipe(iii) Gun-metal stop valve (quarter turn type)with MS lever handle, suitable for 20 mm bore GI tubes, ISI marked, screwed both ends for iron pipe, IN REPAIRS.(iv) Provn of 20 mm bore GI light grade tube from O/H tank to nearest mouth of RWP, IN REPAIRS. 54 S&F, Steel tubes 15 mm bore ‘medium grade’, galvanized with all fittings and fixed to walls and ceilings or laid in floors, complete all as speciifed and directed. 55 S&F, Steel tubes 20 mm bore ‘medium grade’, galvanized with all fittings and fixed to walls and ceilings or laid in floors, complete all as speciifed and directed. 56 S&F, Angular stop valve/cock, cast copper alloy, chromium plated, with wall flange,quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS, complete all as specified and directed. MAKE: PRAYAG Cat No. 6510 or equivalent make mentioned in Appendix B. 57 S&F, Concealed stop valve/cock, cast copper alloy, chromium plated, with wall flange,quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS, complete all as specified and directed. MAKE: PRAYAG Cat No. 6518 or equivalent make mentioned in Appndix B. 58 S&F, Bib tap, cast copper alloy, chromium plated fancy type, long body with wall flange,quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS, complete all as specified and directed. MAKE: PRAYAG Cat No. 6508 or equivalent make mentioned in Appendix B. 59 S&F, Centre hole basin mixer, cast copper alloy chromium plated, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS complete all as specified and directed. MAKE: KEROVIT Cat No. KB111027 or equivalent make mentioned in Appendix B.. 60 S&F, Wall mixer, cast copper alloy chromium plated, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS complete all as specified and directed. MAKE: KEROVIT Cat No. KB511021 or equivalent make mentioned in Appendix B.. 61 S&F Sink mixer, cast copper alloy chromium plated, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS complete all as specified and directed. MAKE: KEROVIT Cat No. KB511024 or equivalent make mentioned in Appendix B.. 62 S&F, 125mm Overhead ABS shower with cast copper alloy chromium plated arm 225 mm long with flange andfixed in position, IN REPAIRS, complete.MAKE: PRAYAG Cat BS-76 or equivalent make mentioned in Appendix B. 63 S&F, Vitreous China wash down water closet pan (pedestal pattern), white ISI marked, with & including stainless steel body Jet spray (L-bend) with 1.50 metre long braded tube tube, soft close PVC seat & cover and uPVC S trap, IN REPAIRS, complete all as specified and directedMAKE OF EWC: PRAYAG Cat No. 4016 or equivalent make mentioned in Appendix B. 64 S&F, Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm, ISI marked, white, with integral foot rests (excluding flushing cistern and flush pipe), 110x125 size uPVC P trap & necessary joints, lime concrete IN REPAIRS, complete all as specified and directed.MAKE: PRAYAG Cat No. 4055 or equivalent make mentioned in Appendix B 65 S&F, Vitreous China wash hand basin, white, flat back, size 550 x 400 mm, ISI marked,including fixing acessories like rag bolts etc. with CP waste coupling half or full threaded suitable for & including 32 mm size PVC solid waste pipe,IN REPAIRS, complete all as specified. MAKE: PRAYAG Cat No. 4645 or equivalent make mentioned in Appendix B 66 S&F, Health fauset with 1 metre SS tube & hook complete. MAKE: PRAYAG Cat No. BEA-97 or equivalent make mentioned in Appendix B. 67 PVC flushing cistern 10 litre capacity, syphonic action type, any shade, dual flush, ISI marked with flush pipe and all fixing acessories,IN REPAIRS, complete all as specified and directed. MAKE: PRAYAG Cat No. 502 or equivalent make mentioned in Appendix B 68 S&F, Corner Glass shelf 300 mm with brass brackets and fixed to wall with chromium plated brass screws and rawl plugs, IN REPAIRS, specified and directed. MAKE: PRAYAG Cat No. BEA-44 or equivalent make mentioned in Appendix B. 69 S&F, Stainless steel round slotted grating with frame, 100 mm size fixed in position with cement joints, IN REPAIRS, complete all as specified and directed. 70 S&F, PVC connections with PTMT nuts, 450 mm long, IN REPAIRS, complete all as specified and directed. 71 S&F, Stainless steel sink, double bowl type, matt finish, made out of SS sheet not less than 1 mm for kitchen with & including plug waste pipe, washers connecting union etc including necessary fixing acessories,overall size 1143 mmx510X203 mm with bowl size 510mm x 405mm x203mm IN REPLACEMENT, complete. MAKE: PRAYAG Cat No. P-1350D or equivalent make mentioned in Appndix B. 72 S&F, Stainless Steel kitchen plate rack of sheet thickness not less than 0.61 mm overall size 786 x 760 x 254 mm, fixed on walls wth PVC plugs and SS screws, INREPAIRS, complete.MAKE: PRAYAG Cat No. P-346 or equivalent make mentioned in Appndix B. 73 S&F, uPVC pipes 75 mm external dia, type-B, ISI marked (IS:13592) single socketed in any length with rubber ring joints, fixed under floors/walls as SWR pipes, IN REPAIRS, complete all as specified and directed. 74 S&F, uPVC pipes 110 mm external dia, type-B, ISI marked (IS:13592) single socketed in any length with rubber ring joints, fixed under floors/walls as SWR pipes, IN REPAIRS, complete all as specified and directed. 75 S&F, uPVC/PVC bend any radius, suitable for uPVC soil waste discharge pipes 75 mm external dia,IN REPAIRS, complete all as specified and directed. 76 S&F, uPVC/PVC bend any radius, suitable for uPVC soil waste discharge pipes 110 mm external dia,IN REPAIRS, complete all as specified and directed. 77 S&F, uPVC/PVC single T, equal or unequal, suitable for uPVC soil waste discharge pipes 75 mm external dia,IN REPAIRS, complete all as specified and directed. 78 S&F, uPVC/PVC single T, equal or unequal, suitable for uPVC soil waste discharge pipes 110 mm external dia,IN REPAIRS, complete all as specified and directed. 79 S&F, uPVC floor trap,suitable for uPVC soil waste discharge pipes 75 mm ext dia, embedded in PCC type B-1(1:2:4), IN REPAIRS, complete all as specified and directed, 80 DISMANTLING/DEMOLITION WORKS :- 81 Taking down cement plaster of any description on brick walls or concrete surfaces etcincluding raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed. 82 Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. 83 Taking up or down steel tubing 15 mm bore and connections, including cleaning for re-fixing or removal to store complete all as specified and directed. 84 Taking up or down steel tubing 20 mm bore and connections, including cleaning for re-fixing or removal to store complete all as specified and directed. 85 Demolition brickwork or stone / boulder masonrybuilt in cement mortar including all quoins, arches, pillars etc complete all as specified and directed 86 Dismantling timber scantling 40 sq. cm and over in section, in any position, complete all as specified and directed. 87 Dismantlingasbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings, complete all as specified and directed. 88 Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed. 89 Dismantling boarding, any description, fixed in any position complete all as specified and directed. 90 Demolition of mud phuska in roofs, of thickness not more than 200 mm including plaster and leeping plaster complete all as specified and directed. 91 Dismantlig brick tiles in roof laid dry and pointed in cement mortar complete all as specified and directed. 92 Notes:Amount ofcredit for retrieved materials is mentionedintender documents in pdf form which will be deducted while acceptance of tender offline.
