Construction of 01 ACR GMS RAJPURA - Earth work in bulk excavation by manual means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m Sq. on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed byEngineer-in-Charge. All kinds of soil : incliding all lead lift and carrige.( Complete job) 2 Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) 3 Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) 4 Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) 5 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. Layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering lead upto 50m and lift upto 1.5m. 6 Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in superstructural above plinth level upto V floorincluding curing in : Cement mortar 1:6 (1 cement : 6 coarse sand) 7 Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and above plinthincluding curing in :Cement mortarCement mortar 1:4 ( 1 cement : 4 coarse sand) 8 Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement.1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) 9 Providing and laying Reinforced Cement Concrete 1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size) in suspended floors, balconies, landings and staircase having upto 15° slope. excluding cost of centering and shuttering , all work upto floor V level,Crushed Aggregate 10 Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete Thermo-Mechanically Treated bars of grade Fe-500Dor more. 11 Centering and shuttering including strutting, propping etc. and removal of form for : 12 Foundations: footings, bases of columns etc. for mass concrete. 13 Suspended floors, roofs, landings, balconies and access platform. 14 Lintels, beams, plinth beams, girders, bressumers and cantilevers. 15 Columns, pillars, piers, abutments, posts, and struts. 16 Edges of slabs and breaks in floors and walls Under 20 cm wide 17 Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60mm thickness, including hinges jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25mm, or base ties of 1.60mm pressed, mild steel welded or rigidly fixed together by mechanical means, including M.S pressed butt hinges 2.5mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-charge:Fixing with adjustable lugs with split end tail to each jamb 18 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete. 9.48.1 Fixed to steel windows by welding 19 6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand) 20 12 mm cement plaster of mix :1:6 (1 cement: 6 fine sand)including alllifts,leads,carriage of the material. 21 15mm Cement plaster on the rough side of single or half brick wall of mix: 1 : 6 ( 1cement : 6 fine sand) .including all lifts,leads,carriage of the material. Complete job 22 Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges brightfinished of required size with necessary screws.First class kail wood 35 mm thick 23 Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. Plain particle board flat pressed, 3 layer or graded wood particle board medium density Grade I, IS : 3087 marked 24 Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.Second class Kail wood 25 Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 250x16 mm 26 Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : 27 150x10mm 28 100x10mm 29 Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade withnecessary screws etc. completez 30 100 mm 31 125mm 32 Providing and fixing aluminum hanging floor door stopper, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :Twin rubber stopper 33 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand)including grouting the joints with white cement and matching pigments etc. complete Size of tile 600x600 mm 34 Applying priming coat with ready mixed pink or grey primer of approved brand and manufacture 35 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.Two or more coats on new work 36 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade.Two or more coats on new work 37 Finishing walls with water proofing cement paint of required shade onNew work (two or more coats applied @ 3.84 kg/10sqm) 38 Making plinth protection 50 mm thick of cement concrete 1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggreagate 20mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth. Crushed 39 Providing and fixing elecctric points complete in all respect as per necessary at site NSI 40 Carriage of material from source to site of work by mechanical transport including loading /unloading and stacking complete. 41 Carriage of materials by mechanical transport including loading / unloading and stackingcomplete. Sand lead up to 50 kms avg. 42 Carriage of materials by mechanical transportincluding loading / unloading and stacking complete. Stone aggregate lead up to 20 kms avg. 43 Carriage of materials by mechanical transport including loading / unloading and stacking complete. Bricks lead up to 80 kms avg.
