Purchase Of Lab Equipments, , Purchase Of Lab Instruments ( Aayushaman Bharat) , Needle Destroyer-(Hub Cutter) Technical Specification- The Cutting Blade Of The Cutter Will Be Made Of Stainless The Thickness Of The Blade Will Not Be Less Than 0.5 Mm One Side Sharpen To Cut Minimum Of 10,000 Cuts. All Other Metal If Used In The Hub Cutter Will Be Made Of Galvanized Carbon Steel Which Will Withstand Rusting Even In Rough Weather With High Humidity Coastal Region For A Minimum Of Five Year(Is 277 Of 2003 – Galvanized Steel Sheet Specification) The Sharp Container Should Be Made Of Polypropylene (Pp) Of Not Less Than 4 Mm Thick And Should Be White/Translucent. Shape: The Shape Of The Container Will Be Such That The Lid Is Tightened With The Body. Capacity Range : Able To Destroy From Hub Of Ad Syringe With Needles From 18-28 Gauge Diameter And From 10-25 Mm Length And Fitted With All Types Of Needle Fittings, Resistance Of Piecing: Container Shall Accept 500 Cut Needle Along With The Hub When It Is ¾ Th Full (Filling Line). Needle Shall Not Penetrate Container Walls When Filled Up To The Filling Line. Tamper-Proofing: When Contaminated Needles Are Being Dropped Into Containers, It Shall Remain Sufficiently Sealed So As To Prevent A Hand From Entering. Needle Should Not Protrude From The Container When The Box Contains 500 Needles With Hub. Capacity Of The Container: Have Sufficient Capacity To Hold 500. Technique : The Device Shall Be Designed To Facilitate The Location And Entry Of The Needles So That The Ad Syringe Is Cut From Hub By Having: A Non-Critical Angle Of The Needle Relative To The Entry Point. Handling : Able To Be Carried In One Hand And Portable Should Be Iso/ Ce Certified. , Cusco Speculum- Technical Specification- Material Should Be Medical Grade Should Be Isi/Bis /Ce/Iso Certified , Lamp With Stand – (Mobile Examination Light) Technical Specification- Operating Lamp, On Mobile Stand. 4 Halogen Bulbs, Each Of 40 Watt, Producing A Total Intensity Of 55,000 Lux Of Cold Light. Colortemperature 4300 K Height Of Stand 190 Cm Horizontal Turning Range 360 Degree Variable Setting Of Lamp Head: 132-265 Cm Diameter Of Lamp Head: 47 Cm Mains Voltage 240 V, 50 Hz With Five High Quality Castors, 2 Of Them Lockable And Balance Should Be Iso/ Ce Certified , Sponge Holding Forceps- Technical Specification- Material Should Be Medical Grade Should Be Isi/Bis /Ce/Iso Certified , Beak Forceps - Technical Specification- Material Should Be Medical Grade Should Be Isi/Bis /Ce/Iso Certified. , Pre-Sterile Wide Mouth Plastic Container With Screw Cap (20Ml,100Ml, Label) , Glucometer- Technical pecification- Should Be A Hand Held Meter Should Require No Routine Maintenance Should Have Reading Range/Linearity From 20 To 600 Mg/Dl Should Have A Maximum Reading Time Of Less Than 10 Seconds Should Use Electrochemical Technology Should Use A Minimum Blood Sample Less Than 1.5?L Should Have A Lcd Display Should Have Measuring Unit In Mg/Dl. Should Have Wide Operating Temperature Should Have A Minimum Memory Of 50 Should Have Life Time Replacement Offer Should Have Easy Code Entry Technique Battery Should Be Replaceable Without Using Any Tools. Should Have Facility To Ensure Accuracy Of Measurements. Should Be Supplied With Three Types Of Control Solutions Of Each At Least 20 Ml Should Have Safety Certificate From A Competent Authority Ce / Fda (Us) / Stqc Cb Certificate / Stqc S Certificate Or Valid Detailed Electrical And Functional Safety Test. , Slide Drying Rack - Technical Specification- Slide Drying Rack Acrylic 54 Slide Capa10 Slots Accommodate 50 Slides. 8.2W X 8.5D X 2.0H (Front) X 4.45H (Rear) , Test Tube Rack - Technical Specification- This Polyethylene Rack Will Hold Six Test Tubes, And Has Six Drying Pins. Sides Are Fully Open For Clear Viewing. Rack Has Two 30Mm And Four 20Mm Holes, And Is Pre-Assembled. , Table Top Centrifuge With 12 Tubes With Stabilizer - Technical Specification- Table Top Centrifuge Should Be Microprocessor Controlled With Large Lc Display Of Time, Speed And Temperature With Digitally Controlled Buttons. Programmable Speed With Separate Short Spin Key (In Seconds). Brushless Maintenance Free Motor Drive With Low Noise Levels Less Than 63 Db At Max Speed. Automatic Rotor Recognition And Automatic Imbalance Detection. Double Lid Locking System For Maximum Safety. Maximum Speed 15,000 To 17,000 Rpm With Maximum Rcf 20,000 To 30,000 X G With Speed/Rcf Increment In Steps Of1,000 Wide Temperature Range Of -150C To +40 C And Must Be Able To Maintain 40 C At Max Speed. Fixed Angle Rotor Accommodating 24 X 1.5/2.0 Ml Conical Reaction Tubes, Incl. Polysulfone Lid. Also Supply Fixed Angle Rotor Made Of Polypropylene For 12 X 1.5/2.0 Ml Conical Reaction Tubes, Incl. Polysulfone Lid. Also Supply Adapter For 0.2 Ml Pcr Reaction Tubes. Rotor And Chamber Should Be Made Of Chemical Resistant And Rust Free Material. Suitable Constant Power Supply Backup/Inbuilt Battery. Machine Should Be En-61010-2-020 Certified & Ce Marked, Ivd Compliant, Certified Bio Containment Lid For Safety Purpose. Technical Specification- Stabilizer- Should Work For Input Voltage Range Of 100-240 Volt Ac Single Phase With High Input Voltage Cut At 240 Volt And 2.5 Kva Step Up Voltage – 10 Volt Per Stage. Overload Protection At Input Automatic Cut-Off Time-Between 2-4 Seconds Of Under Voltage/Over Voltage Cutoff At Output. Maximum Power Loss Due To Leakage Of Current-2% Restart Delay Of 6-9 Minutes After The Cut-Off Along With Quick Start Button. The Output Voltage Should Be Stable And Capable Of Operation Continuously With Respect To Any Change In Ambient Temperature And Regulation Should Be Automatic. Automatic Line Voltage Stabilizer (Step Type) Should Be Of Copper Wound Complete With Voltmeter (Digital/Analog) With Selector Switch To Indicate Input And Output Voltage And Construction Conforming To Is: 8448/1989 Reaffirmed 2003. The Output Side Shall Be Provided With Mcb Of Suitable Rating Duty Isi Marked. Provision For Two Output Sockets Of 15 Amps, Isi Marked. Details Of Transformer Should Be Furnished, Such As Rating, Weight Of Winding And Core, Which Should Be Verified During Inspection. A Metal Oxide Varistor (Mov) For Surge Suppression Should Be Provided And Connected Directly On The Power Line. 4 Line Emitting Diode Should Be Provided To Indicate Power Input, Power Output Equipment In Standby Condition And High Input Voltage. Stabilizer Should Be Isi Certified& Marked. , Refrigerator- Technical Specification- Energy Rating3 Star Capacity270 Liter Double Door Refrigerator Branded In Built Stabilizer Direct Cool Technology 1 Year Warrantyrefrigerator & 4 Year On The Compressor Isi/Iso Certification
