|
| 1 | Carriage of Materials |
| 2 | By Mechanical Transport including loading,unloading and stacking |
| 3 | Lime, moorum, building rubbish Lead - 2 |
| 4 | EARTH WORK |
| 5 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 6 | All kinds of soil. |
| 7 | Supplying chemical emulsion in sealed containers including delivery as specified. |
| 8 | Chlorpyriphos/ Lindane emulsifiable concentrate of 20% |
| 9 | CEMENT CONCRETE (CAST IN SITU) |
| 10 | Providing and laying in position excluding cement concrete of level: specified grade the cost of centering and shuttering - All work up to plinth |
| 11 | 1:2:4 (1Cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 12 | Makingplinthprotection 50mmthickofcementconcrete 1:3:6 (1cement : 3 coarse sand (zone-Ill) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. |
| 13 | REINFORCED CEMENT CONCRETE |
| 14 | Reinforced cement concrete work in walls (any thickness),including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor fivelevel,excludingcost of centering,shuttering, finishingand reinforcement: |
| 15 | 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 16 | Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources). |
| 17 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 18 | Foundations,footings,basesof columns,etc.formass concrete |
| 19 | Walls (anythickness)includingattachedpilasters, butteresses, plinth and string courses etc. |
| 20 | Suspended floors,roofs,landings,balconies and access platform |
| 21 | Shelves (Cast in situ) |
| 22 | Stairs, (excluding landings) except spiral-staircases |
| 23 | Small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like |
| 24 | Steelreinforcement forR.C.C.workincludingstraightening,cutting, bending, placing in position and binding all complete above plinth level. |
| 25 | Thermo-Mechanically Treatedbars of gradeFe-500D or more. |
| 26 | Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. |
| 27 | MASONRY WORK |
| 28 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: |
| 29 | Cement mortar 1:6(1 cement :6 coarse sand) |
| 30 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : |
| 31 | Cement mortar 1:6(1 cement : 6 coarse sand) |
| 32 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in : |
| 33 | cement mortar 1:4(1 cement :4 coarse sand) |
| 34 | Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand). |
| 35 | CLADDING WORK |
| 36 | Providingandfixing 18mmthickgangsawcut,mirrorpolished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters,window sills,facias andsimilar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. |
| 37 | Granite stone slab of colour black, Cherry/Ruby red |
| 38 | Area of slab over 0.50 sqm |
| 39 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3(1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 40 | WOOD AND P. V. C. WORK |
| 41 | Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes (weight not less than 10 kg per sqm) fixing with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. |
| 42 | Second class teak wood |
| 43 | 35 mm thick |
| 44 | Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete (Copper oxidised as per IS 1378) |
| 45 | 250x16 mm |
| 46 | Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS 1378) |
| 47 | 150x10 mm |
| 48 | 100x10 mm |
| 49 | Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete (Copper oxidised as per IS 1378) |
| 50 | 125 mm |
| 51 | 100 mm |
| 52 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 53 | 250x16 mm |
| 54 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 55 | 200x10 mm |
| 56 | 150x10 mm |
| 57 | 100x10 mm |
| 58 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 59 | 125 mm |
| 60 | 100 mm |
| 61 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 62 | Twin rubber stopper |
| 63 | STEEL WORK |
| 64 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 65 | Ingratings,frames,guardbar,ladder,railings,brackets, gates and similar works |
| 66 | Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. |
| 67 | M.S. tube |
| 68 | Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. |
| 69 | 10 x 120 mm |
| 70 | FLOORING |
| 71 | Brick on edge flooring with bricks of class designation 7.5 on a bed of 12 mm cement mortar, including filling the joints with same mortar, with common burnt clay non modular bricks: |
| 72 | 1:6 (1cement :6 coarse sand) |
| 73 | Providing andlayingCeramic glazed floor tiles of size 300x300mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 74 | Providing and laying vitrified floor tiles in diferent sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. |
| 75 | Size of Tile 600x600 mm |
| 76 | Providing and laying Vitrified tiles in floor in diferent sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. |
| 77 | Double charge vitrified tile polished finish of size |
| 78 | Size of Tile 600 x 600 mm |
| 79 | Glazed vitrified floor tiles polished finish of size |
| 80 | Size of Tile 600 x 600 mm |
| 81 | ROOFING |
| 82 | Providing and fixing on wall face unplasticisedRigidPVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. |
| 83 | 75 mm diameter |
| 84 | FINISHING |
| 85 | 12 mm cement plaster of mix: |
| 86 | 1:6 (1 cement: 6 coarse sand) |
| 87 | 15 mm cement plaster on rough side of single or half brick wall of mix: |
| 88 | 1:6(1 cement: 6 coarse sand) |
| 89 | 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix: |
| 90 | 1:4(1 cement: 4 fine sand) |
| 91 | 6 mm cement plaster of mix: |
| 92 | 1:3(1 cement :3 fine sand) |
| 93 | Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement : 3 fine sand): |
| 94 | Flush / Ruled/ Struck or weathered pointing |
| 95 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: |
| 96 | New work (Two or more coats applied @ 1.43 Itr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 97 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 98 | Two or more coats on new work |
| 99 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: |
| 100 | Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture |
| 101 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 102 | White washing with lime to give an even shade: |
| 103 | Old work (two or more coats) |
| 104 | Removing white or colour wash by scrapping and sandpapering and preparing the surface smooth including necessary repairs to scratches etc. complete |
| 105 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 106 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: |
| 107 | One or more coats on old work |
| 108 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade |
| 109 | Old work (one or more coats applied @ 0.83 Itr/10 sqm). |
| 110 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer\"s specification.Two or more coats on new work |
| 111 | REPAIRS TO BUILDING |
| 112 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. |
| 113 | With cement mortar 1:4 (1cement: 4 coarse sand) |
| 114 | Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in- charge. |
| 115 | Hacking of CC flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Charge. |
| 116 | Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineer-in-Charge. (a) Internal Work- Exposed on wall |
| 117 | Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. |
| 118 | Dismantling and Demolishing |
| 119 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. |
| 120 | Nominal concrete 1:3:6 or richer mix (including equivalent design mix) |
| 121 | Nominal concrete 1:4:8 or leaner mix (including equivalent design mix) |
| 122 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. |
| 123 | Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer-in-charge. |
| 124 | Demolishingbrickworkmanually/bymechanicalmeansincluding stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. |
| 125 | In cement mortar |
| 126 | Demolishingbricktilecoveringinterracingincludingstackingof serviceable material and disposal of unserviceable material within 50 metres lead. |
| 127 | Demolishing mud phaska in terracing and disposal of material within 50 metres lead. |
| 128 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 129 | SANITARY INSTALLATIONS |
| 130 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: |
| 131 | White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 132 | Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : |
| 133 | W.C. pan with ISI marked white solid plastic seat and lid |
| 134 | Providing and fixing CP Brass 32 mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. |
| 135 | Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia |
| 136 | Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : |
| 137 | Flat back wash basin of size 550x400 mm |
| 138 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 139 | Providing and fixing plain bend of required degree. |
| 140 | 100 mm dia |
| 141 | Sand cast iron S&S as per IS : 3989 |
| 142 | Providing and fixing collar : |
| 143 | 100 mm |
| 144 | Sand cast iron S&S as per IS - 3989 |
| 145 | 75 mm |
| 146 | Sand cast iron S&S as per IS - 3989 |
| 147 | Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : |
| 148 | 100 mm |
| 149 | 75 mm |
| 150 | WATER SUPPLY |
| 151 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall |
| 152 | 20 mm nominal dia Pipes |
| 153 | 32 mm nominal dia Pipes |
| 154 | ProvidingandfixingChlorinatedPolyvinylChloride(CPVC)pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. |
| 155 | 20 mm nominal dia Pipes |
| 156 | Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc.Internal work - Exposed on wall |
| 157 | 15 mm dia nominal bore |
| 158 | 20 mm dia nominal bore |
| 159 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : |
| 160 | 25 to 40 mm nominal bore |
| 161 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : |
| 162 | 20 mm nominal bore |
| 163 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : |
| 164 | 20 mm nominal bore |
| 165 | Providing and fixing uplasticised PVC connection pipe with brass unions : |
| 166 | 45 cm length |
| 167 | 15 mm nominal bore |
| 168 | Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work): |
| 169 | 20 mm nominal bore |
| 170 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : |
| 171 | 15 mm nominal bore |
| 172 | Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. |
| 173 | 15 mm nominal bore |
| 174 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. |
| 175 | 15 mm nominal bore |
| 176 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 |
| 177 | 15 mm nominal bore |
| 178 | Providing and fixing C.P. Brass extension nipple (size 15 mm x 50 mm) of approved make and quality as per direction of Engineer-in-charge. |
| 179 | Cutting holes up to 30x30 cm in walls including making good the same: |
| 180 | With common burnt clay F.P.S. (non modular) bricks |
| 181 | Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc. |
| 182 | ALUMINIUM WORK |
| 183 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fastenersto be paid for separately) : |
| 184 | For fixed portion |
| 185 | Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 186 | Forshuttersofdoors,windows&ventilatorsincluding providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) |
| 187 | Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 188 | Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/ structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540-F & ISO 11600 |
| 189 | Upto 5 mm depth and 5 mm width |
| 190 | WATER PROOFING |
| 191 | Providingand applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer- in-Charge. |
| 192 | NEW TECHNOLOGIES AND MATERIALS |
| 193 | Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type orof approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge |
| 194 | 25 mm average thickness |
| 195 | Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as perspecifications and direction of Engineer- In-charge complete in all respect. |
| 196 | Epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make |
| 197 | Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used)as per specifications and directions of Engineer-in-charge.Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75 mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2). |
| 198 | 25 mm average thickness in 2 layers. |
| 199 | Minor Civil Maintenance Work |
| 200 | \"Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources: 10 graded brick aggregate 40 mm nominal size derived from natural sources) |
| 201 | \"P/F C.P brass towel rod complete with two C.P.brass brackets fixed to wooden cleats with C.P. brass screws of approved quality size of 600 x 20 mm. |
| 202 | \"Providing and fixing C.P. grating with or without hole for waste pipe for floor/ nahani trap 100 mm dia. weight not less than 100 grams. |
| 203 | \"Providing and fixing C.P flange for C.P bib cock/C.P angle stop cock. |
| 204 | \"Providing and fixing C.P Brass shower rose 15 mm or 20 mm inlet with shower arm (a) 75 mm dia fancy type. |
| 205 | \"Providing and fixing C.P. waste 32 mm dia of make L&K for wash basin / sink. |
| 206 | Providing and fixing fly proof stainless steel grade 304 wire gauge, to Aluminumwindows and Aluminum clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm, with all necessary complete. |
| 207 | \"Providing and fixing C.P waste 40 mm nominal bore for china sink or wash basin (L&K) make. |
| 208 | Providing and fixing C.P basin mixer of 15 mm nominal bore (L&K) make etc. complete |
| 209 | \"Providind and fixing C.P. hand spray (heath faucet) jaquar make or equivalant with push button control and flexible hose connection with C.P hook complete in all respects.\" |
| 210 | \"\"\"Providing and fixing aluminum door seal in door i/c necessary screw etc complete.\"\"\" |
| 211 | \"Construction of modular kitchen as per approved design in type IV.1. Base Unit. (Empty Box) 400 mm 2. Base Unit. (Drawer Basket) 380*485*140 mm 3. Base Unit.(Meta Drawer)m 530*500*86 mm Grain Trolly Basket with porter 520*485*190 mm 4. Base Unit ( Perforated Cutlery)380*485*100 mm Drawer Basket 380*485*100 mm Thali Basket 380*485*140 mm 5. Base Unit.(Bottle P. O. 2 S) 100*485*420 mm 6. Base Unit.( Empty Box) 440 mm - 7. Base Unit (Perforated Cutlery) 420*485*100 mm Drawer Basket each 1 420*485*100 mm Drawer Basket each 1 420*485*140 mm 8. Base Unit. Drawer Basket 420*485*140 mm 9. Base Unit Empty Box 440 mm - 10. Base Unit (Rack)11.Base Unit Empty Box 12. Base Unit Empty Box 13. Marble for Partition 14.Full extention ball bearing sliding telescopic. 15. Wall Unit (Glass & Plate Rack including Drip Tray.)16. Wall Unit (Glass Shutters) 17. Solid Shutters 18. Auto Closing Concealed Hinges 19. Handles 20. Hardware (Screws counter sunk, Connect Fastners, Tags) 21.Fixing & Installation of the complete modular kitchen. \" |
| 212 | Providing and fixing Single point locking handles \"PULSE\" (aluminium & zamak) ( PL205H / Model) of LGF Sysmac ( I ) Pvt. Ltd. or equivalent make as approved powder coated to required colour or shadeincluding the cost of screw and other incidental charges complete as per manufacturers specification. |
