Request For Proposal For Supply Of Machines And Laboratory Equipment’S For Mechanical Engineering In The Premises Of Gec, Buxar.-- --1 Digital Brinell cum Rockwell cum Vickers Hardness Tester Brinell ,Rockwell cum Vickers Hardness Tester Sturdy & Reliable Design. • Easy to operate. • Accessories of Brinell, Rockwell and Vickers Test are part of standard outfit. • There are 4 quick load change options 60,100,150 kgf for Rockwell Test (HRA, HRB, HRC) and 187.5 kgf (BHN) for Brinell Test in this machine. • Direct reading of Rockwell scales HR - A,B,C. • Samples up to 230mm high & 155mm Throat depth can be tested. • Rockwell Scales - NABL Calibration can be provided (on request) • Brinell Scales - NABL Calibration can be provided (on request) Rockwell Scales - A, B, C Brinell Hardness Hardness Resolution - 1.0 of a Rockwell unit Rockwell - 10 kgf Pre Load / 60, 100, 150 kgf Main load. Brinell - 10 kgf Pre Load / 187.5 kgf Main load. Display - Analogue. Accuracy - Conforms to IS 1586 - 2000 (2006) Specimen accommodations: Vertical space - 230mm Horizontal space (from central line) - 155mm Vickers hardness tester: Measuring range 8HV0.3 ~ 2500HV10. Test force: 0.3, 0.5, 1, 3, 5, 10kgf. Accuracy ±3%. Eyepiece: magnification 10X, resolution 0.0625μm. Objective: 10X, 20X. Total magnification: 100X (for observation), 200X (for measuring). Stage elevation manual. Load control automatic (load/dwell/unload). Dwell time 5 ~ 60 second. Based on Vickers (HV), converted to Rockwell (HRA, HRB, HRC, HRD, HRE, HRF, HRG, HRK), Brinell (HB), Superficial Rockwell(HR15N, HR15T, HR30N, HR30T, HR45N, HR45T), Shore(HS) and Strength(MPa). Memory of 27 measurement values for print, browsing and output. LCD display with backlight. Can measure Knoop hardness, Knoop indenter is needed. 2 Fatigue Testing Machine 200kg This machine is used to test the Fatigue strength of materials and to draw S-N Diagram by research institutes, Laboratories, material manufacturers and various industries. This is a rotating beam type machine in which load is applied in reversed bending fashion. The standard 8 mm diameter specimen is held in special holders at its ends and loaded such that it experiences a uniform bending moment. The specimen is rotated at 4200 rpm by a motor. A complete cycle of reversed stresses in all fibers of the specimen is produced during each revolution. The bending moment is applied with a lever system and can be easily changed by moving weight over the lever. Total number of revolutions at which the specimen fails is recorded by a Digital Counter. An interlocking system puts off the motor at specimen failure, Machine meets requirements of IS 5075-1959. Maximum Bending Moment:- 2 Nm Bending Moment adjustable:- 2.5-20 Nm Range:- Range-I 2.5-12.5 Nm/Range-II 12.5-20.0 Nm Gripping Dia of specimen:- 12mm Testing Dia of specimen:- 8 mm Rotating speed:- 4200 RPM Accuracy of applied bending moment:- ± 1 % Digital Counter :- 8 Digit Power required:- 0.5 HP Power Supply:- 3 ph,440 V,50 Hz,A.C 3 Impact Testing Machine. Pendulum Impact Testing Machine Confirms to IS, BS standards & also conforms to BS, EN: 10045-1993 (for Charpy), complete as per Makers’ standard supply. Technical Specification : ( Izod & Charpy) Tests Parameters Charpy/ Izod Initial potential energy (joules) :-300/ 170 Minimum scale graduation :- 2 /2 Pendulum drop angle (Degree):- 140/ 90 Impact velocity (m/sec):- 5.308 /3.994 Distance between axis of rotation and center of strikes (i.e. length of pendulum) (mm):- 813.5 /813.5 Effective weight of pendulum (kg) :-21.300 /21.300 Max total friction and windage losses (% of initial potential energy) :-0.5%/ 0.5% Striking edge : Angle at tip (Degree) :-30/ 75 Radius of curvature (mm):- 2 /0.7 Width of tip (mm) :-18 Horizontal relief (Degree) :-10(IZOD) Vertical relief (degree) :-5(IZOD) Test Piece Supports Suitable for specimen (Max) (mm) :-10 x 10 /10 x 10 Distance between supports (mm) :-40 (+ 0.5, - 0.0) (CHARPY) Taper of support (mm):- 11 + 1 (CHARPY) Radius of curvature at edge (mm) :-1 to 1.5 (CHARPY) Overall size (mm) approx. 760 (L) X 440 (W) X 1925 (H) Net Wight (kg) approx. 425.. Standard Accessories: Charpy Striker :-1 NO Izod striker :-1 NO Combined Charpy / Izod (10 x 10 specimen) support Block :-1 NO Specimen setting Gauges ( for Charpy and Izod) :-2 NOs Set of spanners :-1 Set 4 Torsion Testing Machine Digital Torsion Testing Machine of capacity 100Nm Max. Torque Capacity (Nm):-100 Torque Resolution (Nm):- 0.01 Angle of Twist ( Degree) :- 0.1 Torsion Speed & Direction:- 1.5 RPM Reverse Distance between grips (mm):-0-400 Grips for around bar of Dia (mm) :- 4 – 8/ 8 – 12 Grips for Flat bars thickness Width:- 2 – 8/25 Motor (hp):- 0.5 Power supply:- Three Phase, 415V, 50Hz. AC Overall Size Approx (L x W x H) (mm):- 1325 X 650 X 1375 5 Continuous beam deflection test A steel beam and two load hangers are supplied together with two dial gauges for measuring beam deflections and slopes. This equipment is part of a ranged to both, demonstrate and experimentally confirm basic engineering principles. 6 Strain Measurement 0-200 Gm Strain Gauge Cantilever Trainer kit, Display Type: Digital 7 V- Notch making Machine Cutting Speed: 150mm/min (for Izod and Charpy test) Feed speed: 90 mm/min 8 Verification of Maxwell’s reciprocal theorem A mild steel beam 100cm long and 1.25cm x 4mm in cross section with graduations at every 10cm along the length. Two knife edge supports 70cm apart with a 30cm overhang on one side. A dial gauge with 25mm travel (with a magnetic base) should be supplied with the apparatus. Apparatus to be supplied should be complete with a supporting stand and a set of weights. 9 Universal Milling Machine Surface of Table (MM):800x175 No. of T-Slots:3 Size of T-Slots: ½” Swivel either Side of Table: 45 Cross Traverse (MM):150 Vertical Traverse (MM):400 Longitudinal Traverse (MM):475 Arbor Diameter (MM):25.4 Taper of Spindle: ISO 40 No. of Spindle Speed:6 Range of Spindle Speed (RPM):40 - 700 Spindle Diameter (MM):50 No of Feed in Longitudinal Table Long:2 Main Motor Power (HP):1 Weight (Kgs.):450 Accessories include with above machine: 1 HP 1440 RPM 3 Phase Electric Motor: 1 No. R/F Switch, V-Belt & Fittings: 1 No. Coolant Pump &Fittings: 1 No. Vertical Attachment: 1 No. Foundation Rubber Pad: 4 Nos. Oil – Can: 1 No. Allen Key Set: 1 No. Spanner Set: 1 No. Rotary Table 8” Dia. Milling Vice (100 mm) with Swivel Base Full Universal Dividing Head (110mm) with Chuck I.S.O 40 Collect Adopter with Key Collects 12 Pieces Set 4mm. to 25mm. Stub Milling Arbour (For Holding Shell & Mill Cutter) Boring Head 18-12mm. Clamping Kit 10 Lathe Machine Norton Type Bed length 6 feet, Light Duty High Precision All Geared Head Lathe Machine having Norton Gear Box Lead Screw & Feed Shaft Separate Spindle, Speed 60–1050RPM with Hardened Bed & complete with all standard accessories such as driving plate, center adapter, dead center, change 11 HYDRAULIC HACKSAW MACHINE 8” Cap. Hydraulic Control Hacksaw Machine having Blade Size 16” x 1 ¼” Complete with all standard accessories as per makers supply Cutting Round: 200 Capacity Square: 150 No of stroke per min: 100-125 Blade Size (mm): 400x32 Approx Weight Kg: 350 Motor (1440 RPM): 1 HP 1 HP 1440 RPM 3 Phase Electric Motor: 1 No. R / F Switch, V-Belt & Fitting: 1 No. Hacksaw Blade (16” x 1 ¼”): 1 No. Foundation Rubber Pad: 4 Nos. Oil – Can: 1 No. Allen Key Set: 1 No. Spanner Set: 1 No. 12 Pillar Drill 20 Pillar Drilling Machine 20mm Cap / 8 Speed / 125mm Travel / 4’ Pillar Height Drilling Capacity (mm): 20 Pillar Dia. (mm): 75 Spindle Nose: MT-2 Spindle Travel (mm): 125 Spindle Center To Pillar Surface (mm): 200 No. Of Spindle Speed: 8 Spindle Speed (RPM): 87 - 3200 Table Size (mm): 280x280 Base Size (mm): 460x315 Base To Spindle Nose (mm): 925 Main Motor Power (HP): 1 13 Bench vice 6 inch Bench vice 6 inch 14 Pipe vice 3 inch Pipe vice 3 inch 15 Tap and die set ¼ to ½, Tap and die set ¼ to ½, 16 Drill bits 1/8” to 1/2”, 10 pc set, Drill bits 1/8” to 1/2”, 10 pc set, 17 Hacksaw blade Hacksaw blade 18 Solid frame hacksaw Solid frame hacksaw 19 Steel rule 12, Steel rule 12, 20 Try Square 12 Stainless steel blade Try Square 12 Stainless steel blade 21 Calipers, 10” Calipers, 10” 22 Divider 10” Divider 10” 23 V block 4” V block 4” 24 Vernier Caliper Vernier Caliper 25 Slip Gauge complete Set Slip Gauge Block set, Metric, 87 or 103 Blocks of Grade 1 Steel 26 Vernier calliper (a) Vernier Calliper 3oomm (b) Vernier Calliper 2oomm (c) Vernier Calliper 15omm (d) Inside Vernier Calliper 15omm (e) Vernier Calliper (digital) (f) Vernier Caliper (dial) (h) Screw vernier Caliper 27 MICROMETER (a) Micrometer Outside 0-25mm (b) Micrometer Outside 25-50mm ( c) Micrometer Outside 50-75mm (d) Micrometer Outside 75 -100mm (e) Inside Micrometer 25mm (f) Inside Micrometer 50mm 28 Sine Bar complete Set Sine Bar (100mm, Hardened tool Steel) Sine Bar (200mm, Hardened tool Steel) Sine Centre Complete Set (Roller distance 200mm, Centre height: 65mm or Roller distance: 300mm, center height: 75mm) 29 Vernier Bevel Protector Vernier Bevel Protector (Blade edge angle: 60°, 45° Edge, Blade length: 150mm), Range - 360 Deg, LC:5 Min, it is capable of measuring from 0 to 360°. the vernier scale has 24 divisions coinciding with 23 main scale divisions. thus the least count of the instrument is 5. 30 Straight Edge Straight Edge 31 Gauge Sets (Radius, Thread) Gauge Sets (Radius, Thread ) 32 Thread Plug Gauges ( set of 5 ) Thread Plug Gauges (GO & NO GO Set of different dimensions) 33 Plain Plug Gauges ( Set of 5 ) Plain Plug Gauges (GO & NO Go Set of different dimensions) 34 Snap Gauges ( Set of 5 ) Snap Gauges (GO & NO Go Set of different dimensions) 35 Steel Scale Steel Scale (150mm, 300mm, 1000mm) 36 Caliper (a) Outside firm caliper (6 inch) (b) Inside firm caliper (6 inch) (c) Outside transfer firm caliper (6 inch) (d) Inside transfer firm caliper (6 inch) 37 Spirit Level Spirit Level: 12 inch precision Spirit Level 38 Thread Micrometer Thread Micrometer 39 Autocollimator Telescope magnification: 38x, Objective: f=700mm, effective aperture: 70mm, Measuring range: 30 Minutes of arc (Both vertical and horizontal axis), minimum reading: 0.5 seconds of arc, readout system: Adjustment in view field and reading on micrometer, measuring Accuracy: 0.5 seconds of arc within a range of 5 minutes arc 1 second of arc within a range of 30 minutes of arc, Light Source: LED, Power supply: 12V 5 A 40 DISPLACEMENT MEASUREMENT TRAINER MODULE – LVDT DISPLACEMENT MEASUREMENT TRAINER MODULE – LVDT 41 MECHANICALCOMPARATOR Operates on the principal of the Change of inductance of a coil by movement of a steel armature, which is moved by a plunger arrangement in contact with the surface to be checked. the plunger consists of MechanicalGauge Head with armature and feeler, Ammeter, Power Supply, with 2 amps x 2 Nos. dimmer & specimen Holde 42 PNEUMATIC COMPARATOR Accurate C-jet Dial Type Air Gauge Unit Range ±0.001mm. Oil & Moisture removal filter set Unit, Outlet house, cock valve, pressure indicator., 2jet Air Plug Gauge Dia. 10-20 through bore with setting rings. 43 BEVEL PROTECTOR Range - 360 Deg, LC:5Min, it is capable of measuring from 0 to 360°. the vernier scale has 24 divisions coinciding with 23 main scale divisions. thus the least count of the instrument is 5. 44 Profile Projector Surface Plate 24” x 24” Profile Projector Surface Plate 24” x 24” 45 FLOATING CARRIAGE MICROMETER Work piece :16.20mm | Prism :2 no’s | Method: Two wire method 46 ORIFICE, VENTURI & ROTAMETER APPARTUS Venturi nozzle: A=84…338mm2 angle at the inlet: 10,5° angle at the outlet: 4° Orifice plate flow meter: diameter=14mm Rotameter: max. 1000L/h 6 tube manometers: 390mmWC Required for Operation: Hydraulic bench 47 REYNOLDS NUMBER APPARATUS Water tank capacity: 2200mL Pipe section. length: 675mm inside diameter: 10mm Tank for ink capacity: approx. 250mL Required for Operation: Hydraulic bench 48 REYNOLDS NUMBER APPARATUS Water tank capacity: 2200mL Pipe section. length: 675mm inside diameter: 10mm Tank for ink capacity: approx. 250mL Required for Operation: Hydraulic bench 49 BERNOULIS THEOREM APPARATUS Venturi nozzle A: 84…338mm2 angle at the inlet: 10,5° angle at the outlet: 4° Pitot tube movable range: 0…200m diameter: 4mm Pipes and pipe connectors: PVC Measuring ranges pressure: 0…290mmWC (static pressure) 0…370mmWC (total pressure) Required for Operation: Hydraulic bench 50 PITOT TUBE Pitot static tube: Head diameter: 2.5 mm. Transparent pipe: 32 mm. internal diameter and 430 mm. length approx. Hose connections. Water manometer 500 mm. length. Easy and quick coupling system built in. Required for Operation: Hydraulic bench 51 Single Cylinder Four Stroke Petrol Engine Test Rig Single Cylinder Four Stroke Petrol Engine Test Rig · The setup consists of single cylinder, four stroke, petrol engine connected to Eddy current dynamometer for engine loading. The setup has stand‐alone type independent panel box consisting of air box, fuel tank, manometer, fuel measuring unit, digital speed indicator and digital temperature indicator. · The setup enables study of engine for brake power, BMEP, brake thermal efficiency, volumetric efficiency, specific fuel consumption, air fuel ratio and heat balance. Provision is also made for conducting Morse test. Set up is supplied with MS Excel program for Engine Performance Analysis. · Self-calculation and graphs sheets with excel programming’s for comparison. Solution tabs as reference for online diagnostics to problems. Almost components from highly reputed MNC and international imports. Self-calibration/check techniques available. Specification: - Engine: - Make ‐Honda Model ‐Honda GX200D QX, Type‐Single cylinder, 4 stroke Petrol, Air cooled, 4.1 KW at 3600 rpm, stroke 54 mm, bore 68mm. Capacity 196 cc. Dynamometer: Type eddy current, water cooled Propeller shaft: With universal joints Air box: M S fabricated with orifice meter and manometer Fuel tank: Capacity 15 lit with glass fuel metering column RPM indicator: Digital with non-contact type speed sensor. Temperature sensor: Type Thermocouple, Type K Temperature indicator: Digital, Range 0‐1200 Deg C Load indicator: Digital, Range 0‐50 Kg, Supply 230VAC Load sensor: Load cell, type strain gauge, range 0‐50 Kg 52 Tachometer Tachometer
