Tender For Setting Right Of Vacant Houses No. 363,370,3022,3023,3057 And 616.; 1 Carriage of Materials 2 By Mechanical Transport including loading,unloading and stacking 3 Lime, moorum, building rubbish Lead - 2 km 4 EARTH WORK 5 Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : 6 All kinds of soil 7 Pipes, cables etc. exceeding 80 mm dia. But not exceeding 300 mm dia 8 Supplying chemical emulsion in sealed containers including delivery as specified. 9 Chlorpyriphos/ Lindane emulsifiable concentrate of 20% 10 CEMENT CONCRETE (CAST IN SITU) 11 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 12 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) 13 Centering and shuttering including strutting, propping etc. and removal of form work for : 14 Foundations, footings, bases for columns 15 Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth. 16 REINFORCED CEMENT CONCRETE 17 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. 18 Thermo-Mechanically Treated bars of grade Fe-500D or more. 19 MASONRY WORK 20 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : 21 Cement mortar 1:6 (1 cement : 6 coarse sand) 22 CLADDING WORK 23 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. 24 WOOD AND P. V. C. WORK 25 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). 26 Second class teak wood 27 Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. 28 Second class teak wood 29 35 mm thick 30 Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete : 31 250x16 mm 32 Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 33 200x10 mm 34 150x10 mm 35 100x10 mm 36 Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : 37 125 mm 38 100 mm 39 Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 40 250x16 mm 41 Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 42 200x10 mm 43 150x10 mm 44 100x10 mm 45 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 46 125 mm 47 100 mm 48 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. 49 Twin rubber stopper 50 Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm),with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer- in-charge 51 Extruded section profile size 48x40 mm 52 Providing and fixing to existing door frames. 53 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of H section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. U cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturers specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter). 54 Providing and fixing wire gauge shutters using stainless steel grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in both directions for doors, windows and clerestory windows with necessary screws : 55 35 mm thick shutters 56 With ISI marked stainless steel butt hinges of required size 57 Second class teak wood 58 STEEL WORK 59 Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. 60 Using M.S. angels 40x40x6 mm for diagonal braces 61 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 62 In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete 63 FLOORING 64 Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 65 40 mm thick with 20 mm nominal size stone aggregate 66 Providing and fixing glass strips in joints of terrazo/ cement concrete floors. 67 40 mm wide and 4 mm thick 68 Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. 69 Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer)with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand)jointing with grey cement slurry @3.3 kg/sqm including grouting thejoints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only .Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. 70 Double charge vitrified tile polished finish of size 71 Size of Tile 600 x 600 mm 72 Glazed Vitrified tiles Matt/Antiskid finish of size 73 Size of Tile600 x 600 mm 74 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. 75 Size of Tile 600x600 mm 76 FINISHING 77 15 mm cement plaster on rough side of single or half brick wall of mix: 78 1:6 (1 cement: 6 coarse sand) 79 12 mm cement plaster finished with a floating coat of neat cement of mix : 80 1:4 (1 cement: 4 fine sand) 81 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix : 82 1:4 (1 cement: 4 fine sand) 83 Pointing on brick work or brick flooring with cement mortar 1:3 (1 cement : 3 fine sand): 84 Raised and cut pointing 85 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturers specification. 86 Two or more coats on new work 87 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : 88 Two or more coats on new work 89 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 90 Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture 91 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 92 White washing with lime to give an even shade : 93 Old work (two or more coats) 94 Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 95 Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. 96 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : 97 One or more coats on old work 98 Finishing walls with Acrylic Smooth exterior paint of required shade : 99 Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface 100 REPAIRS TO BUILDING 101 Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. 102 With cement mortar 1:4 (1cement: 4 coarse sand) 103 Hacking of CC flooring including cleaning for surface etc. complete as per direction of the Engineer-in-Charge. 104 Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. 105 Dismantling and Demolishing 106 Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. 107 Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) 108 Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) 109 Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. 110 Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. 111 In cement mortar 112 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : 113 Of area 3 sq. metres and below 114 Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : 115 Of area 3 sq. metres and below 116 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. 117 SANITARY INSTALLATIONS 118 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 119 White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests 120 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : 121 W.C. pan with ISI marked white solid plastic seat and lid 122 Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. 123 Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge. (a) 15 mm nominal dia 124 Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings : 125 Flat back wash basin of size 550x400 mm 126 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. 127 Providing and fixing soil, waste and vent pipes : 128 100 mm dia 129 Centrifugally cast (spun) iron socket & spigot (S&S) pipe as per IS: 3989 130 75 mm diameter : 131 Centrifugally cast (spun) iron socketed pipe as per IS: 3989 132 Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 133 100 mm dia 134 Sand cast iron S&S as per IS - 3989 135 75 mm dia 136 Sand cast iron S&S as per IS- 3989 137 Providing and fixing plain bend of required degree. 138 100 mm dia 139 Sand cast iron S&S as per IS : 3989 140 75 mm dia 141 Sand cast iron S&S as per IS - 3989 142 Providing and fixing single equal plain junction of required degreewith access door, insertion rubber washer 3 mm thick, bolts andnuts complete. 143 100x100x100 mm 144 Sand cast iron S&S as per IS - 3989 145 Providing and fixing terminal guard : 146 100 mm 147 Sand cast iron S&S as per IS - 3989 148 75 mm 149 Sand cast iron S&S as per IS - 3989 150 Providing and fixing collar : 151 100 mm 152 Sand cast iron S&S as per IS - 3989 153 75 mm 154 Sand cast iron S&S as per IS - 3989 155 Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter : 156 100 mm 157 75 mm 158 Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 159 100 mm inlet and 100 mm outlet 160 Sand cast iron S&S as per IS: 3989 161 100 mm inlet and 75 mm outlet 162 Sand cast iron S&S as per IS - 3989 163 WATER SUPPLY 164 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 165 20 mm nominal dia Pipes 166 32 mm nominal dia Pipes 167 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 168 20 mm dia nominal bore 169 25 mm dia nominal bore 170 Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 171 20 mm nominal bore 172 Providing and fixing uplasticised PVC connection pipe with brass unions : 173 45 cm length 174 15 mm nominal bore 175 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 176 15 mm nominal bore 177 Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. 178 15 mm nominal bore 179 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 180 15 mm nominal bore 181 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 182 15mm nominal bore 183 Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge. 184 Cutting holes up to 30x30 cm in walls including making good the same: 185 With common burnt clay F.P.S. (non modular) bricks 186 Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc. 187 DRAINAGE 188 Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 189 100 mm diameter 190 150 mm diameter 191 Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design : 192 100 mm diameter S.W. pipe 193 150 mm diameter S.W. pipe 194 Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 195 100x100 mm size P type 196 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 197 150 x 100 mm size P type 198 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 199 Dismantling of old S.W. pipes including breaking of joints and bed concrete stacking of useful materials near the site within 50 m lead and disposal of unserviceable materials into municipal dumps : 200 150 mm diameter 201 Supplying and fixing C.I. cover 300x300 mm without frame for gully trap (standard pattern) the weight of cover to be not less than 4.5 kg 202 Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : 203 For pipes 100 to 250 mm diameter 204 ALUMINIUM WORK 205 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fastenersto be paid for separately) : 206 For fixed portion 207 Powder coated aluminium (minimum thickness of powder coating 50 micron) 208 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) 209 Powder coated aluminium (minimum thickness of powder coating 50 micron) 210 WATER PROOFING 211 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. 212 Grading roof for water proofing treatment with 213 Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) 214 Providingand applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge. 215 NEW TECHNOLOGIES AND MATERIALS 216 Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type orof approved makeincluding tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge 217 25 mm average thickness 218 Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust freesteel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge. 219 Bars upto 12 mm diameter 220 Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as perspecifications and direction of Engineer-In-charge complete in all respect. 221 Epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make 222 Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used)as per specifications and directions of Engineer-in-charge. 223 25 mm average thickness in 2 layers. 224 MINOR CIVIL MAINTENANCE WORK 225 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources: 10 graded brick aggregate 40 mm nominal size derived from natural sources) 226 P/F C.P brass towel rod complete with two C.P.brass brackets fixed to wooden cleats with C.P. brass screws of approved quality size of 600 x 20 mm. 227 Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of Dia 0.50 mm all complete. For aluminum/ wooden Door and Window shutter including removing old wire mesh where necessary. 228 Providing and fixing C.P. grating with or without hole for waste pipe for floor/ nahani trap 100 mm dia. weight not less than 100 grams. 229 Providing and fixing C.P flange for C.P bib cock/C.P angle stop cock. 230 Providing and fixing C.P Brass shower rose 15 mm or 20 mm inlet with shower arm (a) 75 mm dia fancy type. 231 Providing and fixing C.P. waste 32 mm dia of make L&K for wash basin / sink. 232 Providing and fixing ISI marked flush door shutter non decorative type, core of block board construction with frame of first class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked M.S butt hinges with necessary screw complete. 233 Extra for providing and fixing of 8mm to 9mm thick ceramic glazed wall tiles instead of 5mm thick ceramic glazed wall tiles. 234 Providing and fixing C.P waste 40 mm nominal bore for china sink or wash basin (L&K) make. 235 Providing and fixing C.P basin mixer of 15 mm nominal bore (L&K) make for one piece only 236 Providing and fixing aluminum door seal in door i/c necessary screw etc complete. 237 Providing and fixing of I hook of with ISI marked M.S. pressed butt hinges bright finished of required size. 238 Providind and fixing C.P. hand spray (heath faucet) with push button control and flexible hose connection with C.P hook of L&K make or approved equivalent complete in all respects. 239 Providing and fixing Single point locking handles PULSE (aluminium & zamak) ( PL205H / Model) of LGF Sysmac ( I ) Pvt. Ltd. or equivalent make as approved powder coated to required colour or shadeincluding the cost of screw and other incidental charges complete as per manufacturers specification.
