Tender for construction work of EVM VVPAT warehouse and warehouse meeting hall and officer office on the second floor of the office building in the District Election Office, 1 Earth work in excavation by mechanical means (Hydraulic excavator)I manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.DSR 2.8.1. 2 1:4:8 (1 Cement : 4 coarse sand (zone-Ill) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) DSR 4.1.8 3 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in Cement mortar 1:4 (1 cement : 4 coarse sand)DSR 6.4.2 4 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. as per dsr no 5.33.2.1 5 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. as per dsr no 5.3 6 Centering and shuttering including strutting, propping etc. and removal of form forLintels, beams, plinth beams, girders, bressumers and cantileversas per dsr no 5.9.5 7 Columns, Pillars, Piers, Abutments, Posts and Struts as per dsr no 5.9.6. 8 roofs, landings, balconies and access platform as per dsr no 5.9.3 9 Steel reinforcement for R.C.C. work ready to use ·cut and bend rebars of approved make from factory/workshop to construction site including placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500O ormore. DSR 5.22.B.1 10 12 mm thick plaster with cement and corse sand (1 cement 6 corse send) 13.4.2 11 15 mm thick plaster on the rough side with cement and corse sand (1 cement 6 corse send) 13.5.2 12 Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and comers, all necessary fittings_ complete, including applying a priming ooat of approved steel primer. 10.5.1 13 Providing and fixing factory made ISi marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F70,F48, K11 Band K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, priming coat of approved steel primer, but excluding the cost of other fittings,glass panes complete all as per approved design, (sectional weight of only steel members shall be measured for payment). DSR 10.11.1 14 Providing & fixing glass panes with putty and glazing clips in steel doors,windows, clerestory windows, all complete with 4.0 mm thick glass panes DSR 10.30.1 15 Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete.Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides DSR 10.29.2 16 Cement concrete pavement with 1 :2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including finishing complete. DSR 11.7 17 Providing and laying vitrified floor tiles In different sizes (thickness to be specified by the manufacturer) with water absorption lass than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades,laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand),jointing with gray cement slurry@ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.11 .41.2 Size of Tile 600x600 mm DSR 11.41.2 18 Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and confonning to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bad of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. DSR 11.46.2 Size of Tile 600x600 mm 19 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade DSR 13.62.1 Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture 20 Finishing walls with Acrylic Smooth exterior paint of required shade DSR 13.46.1 New work (Two or more coat applied@ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10sqm) 21 Providing and applying white cement based putty of average thickness 1 mm,of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. DSR 13.80 22 Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour 13.41.1 New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre DSR 13.41.1 23 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming lo IS : 5382, leaving 10 mm gap for thermal expansion, (I) Single socketed pipes 12.41 .2 110 mm dia meter 24 Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings standard size C.P. brass flush pipe, spreaders with unions and damps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever requiredDSR 17.5.1 Single half stall urinal with 5 litre PVC. automatic flushing 25 17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden deals with C.P. brass screws and washers complete. 26 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes. having thennal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of Joints complete as per direction of Engineer in Charge.25 mm nominal dia Pipes 18.7.3 27 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes. having thennal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of Joints complete as per direction of Engineer in Charge.15 mm nominal dia Pipes 18.7.1 28 Providing and rlXing C.P. brass bib cock of approved quality conforming to IS:8931 18.49.1 15 mm nominal bore 29 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.18.48 30 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting_ of fittings and brackets, cutting and making good the walls wherever require: 17.7.1 White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps mm with integral type foot rests 31 Providing and fixing water close squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or Strap, 10 litre low level white P.V.C.flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231 , with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required 17. 1.1 White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests 32 Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level white P.V.C.flushing cistern, including flush pipe, with manuall controlled device (handle lever), conforming to IS : 7231, wilh all fittings and fixtures complete, including cutting and making good the walls and floors wherever 17.2.2 W.C. pan with ISi marked black solid plastic seat and lid 33 Providing and fixing toilet paper holder 17.34.1 C.P. brass 34 Providing and fixing factory made ISi marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F70,F48, K11 Band K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, priming coat of approved steel primer, but excluding the cost of other fittings,glass panes complete all as per approved design, (sectional weight of only steel members shall be measured for payment). DSR 10.11.1 35 Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main T runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross T of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main T at 600 mm center to center to form a grid of 1200x600 mm and secondary cross T of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main T runners to be suspended from ceiling using Gl slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm Gl adjustable rods with galvanised butterfly level clips of size 85 × 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. Gl Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum) 12.52.1 36 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc.DSR 1.14.1 37 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2x2.5 sq. mm + 1 X 2.5 sq. mm earth wire Wiring for circuit/ submain wiring alongwith earth 1.14.2 38 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulatedcopper conductor, single core cable in surface/ 1 recessed medium class PVC conduit as required. 2 x 4 sq. mm + 1 X 4 sq. mm earth wire1.14,3 39 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulatedcopper conductor, single core cable in surface/ 1 recessed medium class PVC conduit as required. 2 x 10sq. mm + 1 X 6 sq. mm earth wire1.14,5 40 Supply and fixing hexagonal/Round G.P. fan box of approved make made up of 1.0mm thick ISI Marked G.P. sheet spot weeldeed Four to Eight holes of 25,4 mm for pipe entry of the box. Holes should be semi- shuttered type with 0.5mm G.P. Sheet made upper & lower cover duty screwed fitted with 300mm round zink coted M.S Bar X 12mm & brand name should be embossed. Fixing with wiring condult laid in the R.C.C roof before concreting alongwith supply of all material, labour, T&P etc. required for proper completion of the work. UPPWD(E&M) 1149 41 Erection and testing of ceiling fan and regulator for room height upto 3.5mts. including supply of 3mm thick G.I. Pipe 19mm dia culy painted, complete in all respects.UPPWD(E&M) 1116 42 Supply and fixing of LED Tube Light batten fitting 9 suitable for up to 1 X 22 watt LED tube light on surface complete in all respect. - UPPWD1413CAT-AA with tube 43 Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min, 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC 19.1 44 Supply and fixing suitable size GI box with modular plate and cover in front on surface or inrecess, including providing and fixing 3 pin 5/6 A each modular socket outlet and 5/6 A modular switch, connections etc. as required .1.31 45 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or inrecess, including providing and fixing 6 pin 5/6 each & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.1.32 46 nstallation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm 1.50.1 47 Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. 4 way (4 + 12), Double door 2.4.1 48 Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, C curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole 2.10.1 49 .Supply and fixing of CO2 type fire extinguisher 4.5 kg. capacity (ISI Marked IS : 2878 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for proper completion of work. UPPWD 1132 50 Supply and Fixing of Fire Extinguisher ABC Type 6.0 kg. Capacity ( ISI Market IS 15683 & TAC approved) complete with initial charge and wall bracket, along with supply of all materials and labour for propercompletion (Firiecon/LifeGurd/Fire fit/Excell) UPPWD 1131 51 Supply and stacking of Fly ash conforming to IRC- 58 at site, including carriage, loading, unloading & stacking up to any lead (measured stacks will be reduced by 20% for payment 2.37 52 Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement: 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.(e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge: 22.7.1. With average thickness of 120 mm and minimum at khurra as 65 mm 53 Supply and Fixinginformation / sign boardi/c all comp. at site made by angle iron 35x35x5 and 1 mm thick M. S. sheet and fixed at site
