1498-02 Engineering Manufacturing Department Items Purchase Amc Servicing Works E Tender (Only Manufacturer Authorized Dealer)-THINNER FOR PAINT MAKE - BERGER / ASIAN/INDIGO WALL PRIMER (WHITE) MAKE - BERGER / ASIAN/INDIGO AINT- 02C CARD FOR VFD MAKE - ABB/DANFOSS/SIEMENS RMIO CARD FOR VFD MAKE - ABB/DANFOSS/SIEMENS RINT CARD 5611 C FOR VFD MAKE - ABB/DANFOSS/SIEMENS CONTROL CARD CON-4 FOR MILL & C/F DRIVE MAKE - ABB/DANFOSS/SIEMENS CON-2 CARD FOR C/F DRIVE MAKE - ABB/DANFOSS/SIEMENS VGA CABLE MALE CONNECTED PLC TO HMI CABLE LENGTH - 2 MTR FOR R.O. PLC PANEL MAKE - ABB/DANFOSS/SIEMENS RED OXIDE MAKE - BERGER / ASIAN/INDIGO PLC MODULE DX 561, SR NO. 1S1202000045418 MAKE - ABB/DANFOSS/SIEMENS HEAT RESISTANCE ANTI CORROSIVE EXTERNAL USE BLACK PAINT. MATERIAL SHOULD HAVE ORIGINAL COMPANY GATE PASS REQUIRED MAKE - BERGER / ASIAN/INDIGO VFD (VARIABLE FREQUENCY DRIVE) - 90 KW, MAKE - ABB/DANFOSS/SIEMENS ABB TIMER MODEL-CT-AHE OFF DELAY WITH AUX SUPPLY TIME RELAY, RANGE 3 SEC- 30 SEC, A1/A2 - 220-230V AC, AIN2 CONTROL CONTACTS. MAKE - ABB/DANFOSS/SIEMENS ABB TIMER MODEL-CT-AHE OFF DELAY WITH AUX SUPPLY TIME RELAY, RANGE 3 SEC- 30 SEC, A1/A2 - 220-230V AC, AIN2 CONTROL CONTACTS. MAKE - ABB/DANFOSS/SIEMENS CHARGING RESISTANCE FOR C/F DRIVE MAKE - ABB/DANFOSS/SIEMENS CHARGING RESISTANCE FOR C/F DRIVE MAKE - ABB/DANFOSS/SIEMENS PLC CPU- PM554-ETH MAKE - ABB/DANFOSS/SIEMENS PLC CPU- PM554-ETH MAKE - ABB/DANFOSS/SIEMENS HMI-CP-405 MAKE - ABB/DANFOSS/SIEMENS HMI-CP-405 MAKE - ABB/DANFOSS/SIEMENS RIBBON CABLE IGBT TO AINT CARD ACS 800 VFD MAKE - ABB/DANFOSS/SIEMENS RIBBON CABLE IGBT FOR DCS 800 MILL DRIVE MAKE - ABB/DANFOSS/SIEMENS RIBBON CABLE FOR DCS 800 C/F DRIVE MAKE - ABB/DANFOSS/SIEMENS RIBBON CABLE FOR DCS 800 C/F DRIVE MAKE - ABB/DANFOSS/SIEMENS CONTROL CARD CON-4 FOR MILL & C/F DRIVE MAKE - ABB/DANFOSS/SIEMENS CONTROL CARD CON-4 FOR MILL & C/F DRIVE MAKE - ABB/DANFOSS/SIEMENS SDCS POWER CARD FOR MILL DRIVE MAKE - ABB/DANFOSS/SIEMENS SDCS POWER CARD FOR MILL DRIVE MAKE - ABB/DANFOSS/SIEMENS CDP CABLE FOR DCS 800-SO2-0520-05 MAKE - ABB/DANFOSS/SIEMENS VFD (VARIABLE FREQUENCY DRIVE),ACS 580 - 01,363 AMP- 4 FOR ID FAN MAKE - ABB/DANFOSS/SIEMENS COM-2 CARD FOR C/F DRIVE MAKE - ABB/DANFOSS/SIEMENS AMC , SERVICING AND OVERHAULING OF BOILER FEED PUMP TYPE -HDA-80/13, WITH TRIAL, MAKE - KSB AMC, SERVICING AND OVERHAULING OF BOILER FEED PUMP TYPE -HDA 65/15 , WITH TRIAL, MAKE - KSB AMC , SERVICING AND OVERHAULING OF SOFT STARTER PANEL(ABB) OF FEED PUMP MOTOR TYPE- PSTB-370-600-70-ISFA894015R7000. SERVICE WITH TRAIL. MAKE - ABB/SEIMENS/MITSUBISHI AMC , SERVICING AND OVERHAULING OF ID FAN MOTOR DRIVE PANEL ABB TYPE- ACS 800-4-0260. SERVICE WITH TRAIL. MAKE - ABB/SEIMENS/MITSUBISHI AMC , SERVICING AND OVERHAULING OF FD FAN MOTOR DRIVE PANEL ABB TYPE- ACS-800-04-0135-3. SERVICE WITH TRAIL. MAKE - ABB/SEIMENS/MITSUBISHI AMC , SERVICING AND OVERHAULING OF SA FAN MOTOR DRIVE PANEL ABB TYPE- ACS-550-01-180A-4. SERVICE WITH TRAIL MAKE - ABB/SEIMENS/MITSUBISHI AMC , SERVICING AND OVERHAULING OF BAGASSE FEEDER 4 NOS DRIVE PANEL ABB ACS-550-01-012H-4. SERVICE WITH TRAIL. MAKE - ABB/SEIMENS/MITSUBISHI AMC , SERVICING AND OVERHAULING OF CENTRIFUGAL MACHINE DC MOTOR DRIVE PANEL ABB TYPE- DCS-800, ABB PLC TOUCH SCREEN HMI COMPLETE AMC FOR CENTRIFUGAL MACHINE THROUGOUT THE SEASON WITH ENGINEER. MAKE - ABB/SEIMENS/MITSUBISHI AMC , SERVICING AND OVERHAULING OF R.O. PLANT ABB PLC PANEL SERVICE & TRAIL. MAKE - ABB/SEIMENS/MITSUBISHI AMC , SERVICING AND OVERHAULING OF POWER HOUSE ACB 4000A (PCC1, PCC2) OVER HAULING & SERVICING & TRAIL. MAKE - ABB/SEIMENS/MITSUBISHI AMC , SERVICING AND OVERHAULING OF POWER HOUSE ACB 1000A (PCC1) OVER HAULING & SERVICING & TRAIL. MAKE - ABB/SEIMENS/MITSUBISHI AMC , SERVICING AND OVERHAULING OF POWER HOUSE ACB 1600A (C/F) OVER HAULING & SERVICING & TRAIL. MAKE -ABB/SEIMENS/MITSUBISHI AMC , SERVICING AND OVERHAULING OF POWER HOUSE ACB 2000A, (PCC3/4) OVER HAULING & SERVICING & TRAIL. MAKE -ABB/SEIMENS/MITSUBISH AMC , SERVICING AND OVERHAULING OF POWER HOUSE H.T. DISTRIBUTION VCB 800A PANEL OVERHOULING & SERVICING & TRIAL. MAKE - ABB/SEIMENS/MITSUBISHI/CROMPTON GREAVES AMC , SERVICING AND OVERHAULING OF POWER HOUSE H.T. DISTRIBUTION VCB 400A, PANEL OVERHOULING & SERVICING & TRAIL MAKE - ABB/SEIMENS/MITSUBISHI/CROMPTON GREAVES AMC , SERVICING AND OVERHAULING OF POWER HOUSE H.T. MAIN INCOMMER 6 MW 1250A, VCB PANEL OVERHOULING & SERVICING & TRIAL. MAKE - ABB/SEIMENS/MITSUBISHI AMC OF D.G.SETS. 625 KVA / UTA-25-G5-1 SERVICE P.A. MAKE INCHCUMINSINCH JAKSON MAKE - CUMMINS JACKSON AMC OF D.G.SETS. 320 KVA / NTA-855-G2-1 SERVICE P.A. MAKE - CUMMINS JACKSON AMC OF D.G.SETS 125 KVA / 6BTAA S-9-G3 SERVICE P.A. . MAKE - CUMMINS JACKSON AMC OF D.G.SETS 25 KVA SX - 3 SERVICE P.A. MAKE - CUMMINS JACKSON TRANSFORMER OIL FILTRATION -1250 LTR, OIL BDV TESTING UPTO 60 KV, SHORTAGE OIL FILLING ,WITH TEATING AND TRAIAL COMPLETE JOB. 2500 KVA MAKE - VOLTAMP AMC FOR SERVICING ,TESTING AND TRIAL OF TRANSFORMER COMPLETE JOB. 2500 KVA 2500 KVA MAKE - VOLTAMP FOR PAINTING OF TRANSFORMER COMPLETE JOB. 2500 KVA MAKE - VOLTAMP TRANSFORMER OIL FILTRATION -1000 LTR, OIL BDV TESTING UPTO 60 KV, SHORTAGE OIL FILLING , COMPLETE JOB. 1500 KVA MAKE - VOLTAMP AMC FOR SERVICING ,BUSHING,TESTING AND TRIAL OF TRANSFORMER COMPLETE JOB. 1500 KVA MAKE - VOLTAMP FOR PAINTING OF TRANSFORMER COMPLETE JOB. 1500 KVA MAKE - VOLTAMP AMC , SERVICING AND OVERHAULING OF MILL RAKE ELEVATOR MOTOR DRIVE PANEL ABB TYPE- ACS-550-01-072. SERVICE WITH TRAIL. MAKE - ABB/SEIMENS/MITSUBISHI AMC , SERVICING AND OVERHAULING OF FABRIZER MOTOR 1250A, VCB PANEL OVERHAULING & SERVICING & TRIAL MAKE - ABB AMC & MAINTANCE OF COMPLETE MILL DCS SYSTEM ALONG WITH JUICE AND WATER FLOW STABLIZATION SYSTEM (RHYTHM MAKE) ALL OTHER INSTRUMENT SYSTEM OF ALL MILL TANDEM.AND INSTRUMENT ENGINEER WILL BE DEPUTED IN FACTORY FOR SEASON, MAKE - ABB/SEIMENS/MITSUBISHI TRAIL AND TESTING OF ALL ELECTRICAL PANEL, BREAKER, SKILLED ELECTRICAL EGINEER : - ENGINEER CAPABLE FOR HANDLING OF ALL ELECTRICAL FAULT ,ENGINEER MUST BE AVAILABLE AT PLANT IN ALL RUNNING SEASON FOR TROUBLESHOOTING ,ENGINEER SHOULD BE ABLE FOR MILL DRIVE, ALL BOILER DRIVES, CENTRIFUGAL PANEL MOTOR DRIVE , ALTERNATOR CONTROL ROOM PANEL (GPR) ALONG WITH AVR , ALL BREAKERS (ACB & VCB), SOFT STATER ETC, (ANY DAMAGE DUE TO MISS HANDLING BY ENGINEER DURING INSTALATION/OPRATION WILL BE RECOVEED FROM CONTRACTOR , IN CASE OF ANY ACCIDENT, INJURY OR LIVE LOSSES/PROPERTY LOSSES ARE WILL BE CONTRACTORS RESPONSIBILITY , FACTORY MANAGMENT SHOULD NOT BE RESPONSIABLE OR LIABLE FOR THIS LOSS). THE FACTORY WILL PROVIDE BACHLOR ACCOMMODATION AND MEAL FOR TWO TIME ONLY.. NOTE: - CONTRACTOR SHOULD HAVE ATLEAST 10 YEARS EXPERIENCE IN SUGAR INDUSTRY AND SHOULD HAVE MINIMUM 15 CRORE TURNOVER IN THE LAST THREE FINANCIAL YEAR. MAKE - ABB/SEIMENS/MITSUBISHI INSTRUMENT ENGINEE FOR COMPLETE PLANT INSTRUMENT FAULT WORK (ENGINEER SHOULD HAVE ATLEAST 5 YEAR EXPERIENCE IN SUGAR PLANT ) SKILLED ENGINEER CAPABLE FOR HANDLING OF INSTRUMENT WORK ,MUST BE AVAILABLE AT PLANT IN ALL RUNNING SEASON FOR TROUBLESHOOTING, AMC CONTRACT( EGINEER ) SHOULD BE EXPERIANCE IN MAINTENANCE OF COMPLETE MILL DCS AUTOMATION, ALL BOILER INSTRUMENT, AUTOMATION CENTRIFUGAL, PAN SECTION, SUGAR HOUSE SECTION, PRDS SECTION,POWER TURBINE, INSTRUMENTAION, AUTOMOTION ETC, (ANY DAMAGE DUE TO MISS HANDLING BYCONTRACT ENGINEER DURING INSTALATION/OPRATION WILL BE RECOVERED FROM CONTRACTOR , IN CASE OF ANY ACCIDENT, INJURY OR LIVE LOSSES/PROPERTY LOSSES ARE WILL BE CONTRACTORS RESPONSIBILITY , FACTORY MANAGMENT SHOULD NOT BE RESPONSIABLE OR LIABLE FOR THIS LOSS). THE FACTORY WILL PROVIDE BACHLOR ACCOMMODATION AND MEAL FOR TWO TIME ONLY.. NOTE: - CONTRACTOR SHOULD HAVE ATLEAST 10 YEARS EXPERIENCE IN SUGAR INDUSTRY AND SHOULD HAVE MINIMUM 15 CRORE TURNOVER IN THE LAST THREE FINANCIAL YEAR. MAKE - ABB/SEIMENS/MITSUBISHI SKILLED ELECTRICAL EGINEER FOR CO-GEN (MANPOWER): - (DURING SEASON/OFF SEASON AS PER REQUIREMENT) AN GRADUATE ELECTRICAL ENGINEER WITH EXPERIANCE OF CO-GENERATION AND POWER EXPORT MIN. 5 YEARS. HE CAN HANDLE THE ENTIRE CO-GENERATION PLANT & CAN DO THE LAISENING WITH CSPDCL/GOVT. ATHOURITIES FOR SMOOTH OPERATION PF CO-GENRATION PLANT AND POWER EXPORT RESPONCIBILITY INCLUDES START-UP/SYNCHRO./METERING/BILLING WORK AND ALL POWER EXPORT RELATED ACTIVITIES AS UNDER- 1. POWER IMPORT/EXPORT PLANNING 2. POWER IMPORT/EXPORT MEETERING 3. BILL VERIFICATION BY CSPDCL 4. POWER IMPORT/EXPORT/GENERATION MONITORING 5. SYNCHRONISATION WITH GRID 6. GRID FAULT REPORTING TO CSPDCL. (WORKING FOR FULL CRUSHING SEASON/OFF SEASON ) IN CASE OF ANY ACCIDENT, INJURY OR LIVE LOSS TO THE CONTRACTORS STAFF/PROPERTY LOSS FACTORY MANAGMENT SHOULD NOT BE RESPONSIABLE OR LIABLE FOR THIS LOSS RECOVERED BY COTRATOR).THE FACTORY WILL PROVIDE ACCOMMODATION AND FOOD. NOTE:-BIDDER SHOULD HAVE ATLEAST 10 YEAR EXPERIENCE IN SUGAR INDUSTRY AND SHOULD HAVE 15 CRORE TRUNOVER IN LAST THREE FINANCIAL YEAR. MAKE- ABB/SEIMENS/ MITSUBISHI AMC SERVICING OF TRIVENI TURBINE AND ALTERNATOR ,SEASON/OFF SEASON Pressure Transmitter, Type-Fixed, Size-0 to 2.5 kg/cm2,Two wire pressure transmitter,24 volt loop powered. MAKE - ABB/DANFOSS/SIEMENS SS BODY FOR MELTER, MODEL - UMHQ 50/32, 1450 RPM, CAP.- 30 M3/HR,MWC - 30 MTR, ,SUCTION - 100 MM,DELIVERY - 50 MM, MAKE- SINTECH HOUSING FOR PUMP, MODEL - SWP - 40/320, CAP.- 18 M3/HR, MWC - 30 MTR,SUCTION - 65 MM,DELIVERY - 40 MM, MAKE- SINTECH HOT WATER PUMP (VERTICLE CRYSTLIZER SIDE) MODEL-SWP 65/320, W.O-16/27/05/08, CAPACITY-50M3/HR., MWC-30, MOTOR-9.3KW, SPEED-1440RPM, SUCTION-100 MM, DELIVERY-65 MM. S.S. SHAFT MAKE - SINTECH S.S. IMPELLER FOR MUD PUMP. MODEL- SSHQ 50/260, NO. -16/27/05/08, Sr. No.- 6863, 6862, CAPACITY-50M3/HR., MWC-18,SPEED-1450 RPM SUCTION-80 MM, DELIVERY-50 MM. MAKE - SINTECH S.S. IMPELLER FOR SEMIKESTNER CONDENSATE PUMP & VAPOUR CELL, MODEL- SWP - 65/320, CAPACITY - 50 M3/HR., MOTOR - 11 KW, MWC- 30, SPEED- 1445 RPM, SUCTION- 100 MM, DELIVERY - 65 MM.MAKE - SINTECH S.S. IMPELLER FOR SULPHERED SYRUP PUMP. MODEL- UMHQ 65/320, CAPACITY- 45 M3/HR. MWC-15, MOTOR- 15KW, SPEED 1450 RPM, SUCTION - 125 MM, DELIVERY-65. MAKE - SINTECH S.S. SLEEVE FOR SEMIKESTNER CONDENSATE PUMP & VAPOUR CELL, MODEL- SWP - 65/320, CAPACITY - 50 M3/HR., MOTOR - 11 KW, MWC- 30, SPEED- 1445 RPM, SUCTION- 100 MM, DELIVERY - 65 MM. MAKE - SINTECH PUMP HOUSING (C.I.) FOR QUWARD CONDENSATE PUMP MODEL NO- SWP-50/320, CAP- 30M3/HR, MWC- 30 MTR,SECTION - 80 MM,DELEVARY - 50 MM MAKE - SINTECH PUMP HOUSING (C.I.) FOR QUWARD CONDENSATE PUMP MODEL NO- SWP-40/320, CAP- 18M3/HR, MWC- 30 MTR,SECTION - 65 MM,DELEVARY - 40 MM , MAKE - SINTECH HOT WATER PUMP (VERTICLE CRYSTLIZER SIDE) MODEL-SWP 65/320, W.O-16/27/05/08, CAPACITY-50M3/HR., MWC-30, MOTOR-9.3KW, SPEED-1440RPM, SUCTION-100 MM, DELIVERY-65 MM. S.S. SLEEVE MAKE - SINTECH S.S. SLEEVE FOR COLD WATER PUMP. MODEL NO.- SWP-125/320, CAPACITY- 190M3/HR, MWC-30, SUCTION - 150 MM, DELIVERY-125 MM. MAKE - SINTECH S.S. SHAFT FOR COLD WATER PUMP. MODEL NO.- SWP-125/320, CAPACITY- 190M3/HR, MWC-30, SUCTION - 150 MM, DELIVERY-125 MM. MAKE - SINTECH S.S. IMPELLER FOR COLD WATER PUMP. MODEL NO.- SWP-125/320, CAPACITY- 190M3/HR, MWC-30, SUCTION - 150 MM, DELIVERY-125 MM. MAKE - SINTECH S.S. SHAFT FOR SCRREND JUICE PUMP MODEL NO. - CPS 150/500, CAPACITY - 150 M3/HR, MWC - 60, SUNCTION - 200 MM, DELIVERY - 150 MM, MAKE - SINTECH S.S. SLEEVE FOR SCRREND JUICE PUMP MODEL NO. - CPS 150/500, CAPACITY - 150 M3/HR, MWC - 60, SUCTION - 200 MM, DELIVERY - 150 MM, MAKE - SINTECH S.S. IMPELLER SLEEVE FOR SCRREND JUICE PUMP MODEL NO. - CPS 150/500, CAPACITY - 150 M3/HR, MWC - 60, SUCTION - 200 MM, DELIVERY - 150 MM, MAKE - SINTECH SS BODY FOR MUD PUMP MODEL - SSHQ-50/26,CAPA - 50 M3/HR,MWC - 18 ,SUCTION-80 MM,DELEVERY - 50 MM, MAKE - SINTECH SS WEAR PLATE FOR MUD PUMP MODEL - SSHQ-50/26,CAPA - 50 M3/HR,MWC - 18 ,SUCTION-80 MM,DELEVERY - 50 MM, MAKE - SINTECH SS SLEEV FOR MUD PUMP MODEL - SSHQ-50/26,CAPA - 50 M3/HR,MWC - 18 ,SUCTION-80 MM,DELEVERY - 50 MM, MAKE - SINTECH SS IMPELLOR FOR MODEL - CPS - 100/450,CAPA - 150 M3/HR,MWC - 70 ,MOTOR - 55 KW ,RPM - 1450 ,SUCTION-150 MM,DELEVERY - 100 MM,WITH MOTOR MAKE - SINTECH FILTRATE PUMPS. MODEL-CPS 65/260, CAPACITY-50M3/HR. , MWC-20, MOTOR- 7.5 KW, SPEED-1450 RPM, SUCTION-100 MM, DELIVERY-65 MM. S.S. SHAFT MAKE - SINTECH FILTRATE PUMPS. MODEL-CPS 65/260, CAPACITY-50M3/HR. , MWC-20, MOTOR- 7.5 KW, SPEED-1450 RPM, SUCTION-100 MM, DELIVERY-65 MM. S.S. IMPELLER MAKE - SINTECH J.H.CONDENSATE PUMP. MODEL -SWP 40/320, CAPACITY - 15M3/HR./ MWC- 30, SUCTION-65 MM, DELIVERY - 40 MM. S.S. SLEEVE MAKE - SINTECH SULPHITED JUICE PUMP. MODEL- CPS 100/450, CAPACITY-150M3/HR., MWC-70, RPM-1450, SUCTION-150 MM , DELIVERY-100 MM. S.S. SHAFT MAKE - SINTECH SULPHITED JUICE PUMP. MODEL- CPS 100/450, CAPACITY-150M3/HR., MWC-70, RPM-1450, SUCTION-150 MM , DELIVERY-100 MM. S.S. SLEEVE MAKE - SINTECH CLEAR JUICE PUMP MODEL N0. - CPS - 100/320 CAPACITY - 150 M3/HR, MWC - 30, RPM-1450, SUNCTION - 125 MM DELIVERY - 100 MM. S.S. BODY MAKE - SINTECH CLEAR JUICE PUMP MODEL N0. - CPS - 100/320 CAPACITY - 150 M3/HR, MWC - 30, RPM-1450, SUNCTION - 125 MM DELIVERY - 100 MM. S.S. SHAFT MAKE - SINTECH CLEAR JUICE PUMP MODEL N0. - CPS - 100/320 CAPACITY - 150 M3/HR, MWC - 30, RPM-1450, SUNCTION - 125 MM DELIVERY - 100 MM. S.S. WEAR PLATE MAKE - SINTECH S.S IMPELLOR SULPHITED JUICE PUMP CAPACITY- 100/450/150M3/HR MWC - 70, RPM- 1450, SUCTION -150 MM DELIVERY - 100 MM, MAKE SINTECH CLEAR JUICE PUMP MODEL N0. - CPS - 100/320 CAPACITY - 150 M3/HR, MWC - 30, RPM-1450, SUNCTION - 125 MM DELIVERY - 100 MM. S.S. SLEEVE MAKE - SINTECH S.S. SHAFT FOR LIME PUMP, MODEL-STF 50/32, CAPACITY - 6 M3/HR, MWC-20, SUCTION -65 MM, DELIVERY- 50 MM. MAKE - SINTECH S.S. SLEEVE FOR LIME PUMP, MODEL-STF 50/32, CAPACITY - 6 M3/HR, MWC-20, SUCTION -65 MM, DELIVERY- 50 MM. MAKE - SINTECH S.S. SHAFT FOR MUD PUMP. MODEL- SSHQ 50/26, NO. -16/27/05/08, Sr. No.- 6863, 6862, CAPACITY-50M3/HR., MWC-18,SPEED-1450 RPM SUCTION-80 MM, DELIVERY-50 MM. MAKE - SINTECH S.S. SLEEVE FOR MUD PUMP. MODEL- SSHQ 50/26, NO. -16/27/05/08, Sr. No.- 6863, 6862, CAPACITY-50M3/HR., MWC-18,SPEED-1450 RPM SUCTION-80 MM, DELIVERY-50 MM. MAKE - SINTECH S.S. BODY FOR MUD PUMP. MODEL- SSHQ 50/26, NO. -16/27/05/08, Sr. No.- 6863, 6862, CAPACITY-50M3/HR., MWC-18,SPEED-1450 RPM SUCTION-80 MM, DELIVERY-50 MM. MAKE - SINTECH S.S. BODY FOR MUD PUMP. MODEL- SSHQ 50/26, NO. -16/27/05/08, Sr. No.- 6863, 6862, CAPACITY-50M3/HR., MWC-18,SPEED-1450 RPM SUCTION-80 MM, DELIVERY-50 MM. MAKE - SINTECH S.S. SHAFT FOR FILTRATE PUMPS. MODEL-OPS 65/260, CAPACITY-50M3/HR. , MWC-20, MOTOR- 7.5 KW, SPEED-1450 RPM, SUCTION-100 MM, DELIVERY-65 MM. MAKE - SINTECH S.S. BODY FOR FILTRATE PUMPS. MODEL-OPS 65/260, CAPACITY-50M3/HR. , MWC-20, MOTOR- 7.5 KW, SPEED-1450 RPM, SUCTION-100 MM, DELIVERY-65 MM. MAKE - SINTECH S.S. WEAR PLATE FOR FILTRATE PUMPS. MODEL-OPS 65/260, CAPACITY-50M3/HR. , MWC-20, MOTOR- 7.5 KW, SPEED-1450 RPM, SUCTION-100 MM, DELIVERY-65 MM. MAKE - SINTECH S.S. SLEEVE FOR FILTRATE PUMPS. MODEL-OPS 65/260, CAPACITY-50M3/HR. , MWC-20, MOTOR- 7.5 KW, SPEED-1450 RPM, SUCTION-100 MM, DELIVERY-65 MM. MAKE - SINTECH S.S. SHAFT FOR VACCUM FILTER CAKE WASH PUMP. CPS 40/16, CAPACITY - 20 M3/HR. MWC-40, MOTOR - 7.5KW, SPEED- 2900 RPM, SUCTION-65 MM, DELIVERY- 40 MM. MAKE - SINTECH S.S. SLEEVE FOR VACCUM FILTER CAKE WASH PUMP. CPS 40/16, CAPACITY - 20 M3/HR. MWC-40, MOTOR - 7.5KW, SPEED- 2900 RPM, SUCTION-65 MM, DELIVERY- 40 MM. MAKE - SINTECH S.S. SLEEVE FOR 3rd BODY EVAPORATOR CONDENSATE PUMP , CAPACITY- 30 M3/HR. MWC-30, SUCTION- 80MM, DELIVERY- 50MM, SPEED- 1450 RPM. MAKE - SINTECH S.S. SLEEVE FOR 4th & 5th BODY EVAPORATOR CONDENSATE PUMP , MODEL- SWP - 40/320, CAPACITY- 18 M3/HR. MWC-30, MOTOR- 5.5 KW, SPEED- 1450 RPM, SUCTION- 65 MM, DELIVERY- 40 MM. MAKE - SINTECH S.S. SHAFT FOR SULPHERED SYRUP PUMP. MODEL- UMHQ 65/32, CAPACITY- 45 M3/HR. MWC-15, MOTOR- 15KW, SPEED 1450 RPM, SUCTION - 125 MM, DELIVERY-65. MAKE - SINTECH S.S. SLEEVE FOR SULPHERED SYRUP PUMP. MODEL- UMHQ 65/32, CAPACITY- 45 M3/HR. MWC-15, MOTOR- 15KW, SPEED 1450 RPM, SUCTION - 125 MM, DELIVERY-65. MAKE - SINTECH S.S.SHAFT FOR PAN CONDENSATE PUMP, CAPACITY-50 M3/HR., MODEL-SWP 65/320, MWC-30, SUCTION-100 MM, DELIVERY-65 MM, MOTOR-9.3KW, SPEED- 1450 RPM. MAKE - SINTECH S.S. SLEEVE FOR PAN CONDENSATE PUMP, CAPACITY-50 M3/HR., MODEL-SWP65/320, MWC-30, SUCTION-100 MM, DELIVERY-65 MM, MOTOR-9.3KW, SPEED- 1450 RPM. MAKE - SINTECH S.S. SHAFT FOR INJECTION PUMP (SMALL), MAKE CPS 200/320, CAPACITY- 450 M3/HR. MWC-17, MOTOR-37 KW. SPEED- 1470 RPM, SUCTION- 250 MM, DELIVERY- 200 MM. MAKE - SINTECH S.S. SLEEVE FOR INJECTION PUMP (SMALL), MAKE CPS 200/320, CAPACITY- 450 M3/HR. MWC-17, MOTOR-37 KW. SPEED- 1470 RPM, SUCTION- 250 MM, DELIVERY- 200 MM. MAKE - SINTECH S.S. SLEEVE FORBIG INJECTION PUMP. MODEL- SMF 35/35, CAPACITY- 1200 M3/HR., MWC-17, MOTOR 90 KW, SPEED- 980 RPM, SUCTION- 350 MM, DELIVERY-350 MM. MAKE - SINTECH S.S. SHAFT FOR BIG INJECTION PUMP. MODEL- SMF 35/35, CAPACITY- 1200 M3/HR., MWC-17, MOTOR 90 KW, SPEED- 980 RPM, SUCTION- 350 MM, DELIVERY-350 MM. MAKE - SINTECH WEIGHT BALANCING SPRING FOR BIG INJECTION PUMP. MODEL- SMF 35/35, CAPACITY- 1200 M3/HR., MWC-17, MOTOR 90 KW, SPEED- 980 RPM, SUCTION- 350 MM, DELIVERY-350 MM. MAKE - SINTECH SERVICE WATER PUMP. W.O-16/027/05/08, MODEL-SWP 125/32, CAPACITY-200M3/ HR. MWC- 30, SPEED-1450 RPM, SUCTION-150 MM, DELIVERY-125 MM. S.S. SHAFT MAKE - SINTECH S/S/SLEEVE FOR SERVICE WATER PUMP. W.O-16/027/05/08, MODEL-SWP 125/32, CAPACITY-200M3/ HR. MWC- 30, SPEED-1450 RPM, SUCTION-150 MM, DELIVERY-125 MM. MAKE - SINTECH S.S. SHAFT FOR SPRAY PUMP, MODEL- SMF 40/45, CAPACITY- 2600 M3/HR., MOTOR-132KW, SPEED- 980RPM, SUCTION- 450 MM, DELIVERY- 400 MM. MAKE - SINTECH WEIGHT BALANCING SPRING FOR SPRAY PUMP, MODEL- SMF 40/45, CAPACITY- 2600 M3/HR., MOTOR-132KW, SPEED- 980RPM, SUCTION- 450 MM, DELIVERY- 400 MM. . MAKE - SINTECH S.S. SHAFT FOR MODEL CPS 32/260, Sr. No.- 8234, CAPACITY -20M3/HR.,W.O -11/CPS-D-0039 SUCTION-50 MM, DELIVERY - 32 MM. MAKE - SINTECH MODEL CPS 32/260, Sr. No.- 8234, CAPACITY -20M3/HR.,W.O -11/CPS-D-0039 SUCTION-50 MM, DELIVERY - 32 MM. S.S. WEAR PLATE MAKE - SINTECH MODEL CPS 32/260, Sr. No.- 8234, CAPACITY -20M3/HR.,W.O -11/CPS-D-0039 SUCTION-50 MM, DELIVERY - 32 MM. S.S. SLEEVE MAKE - SINTECH S.S. SLEEVE FOR SPRAY PUMP, MODEL- SMF 40/45, CAPACITY- 2600 M3/HR., MOTOR-132KW, SPEED- 980RPM, SUCTION- 450 MM, DELIVERY- 400 MM. MAKE - SINTECH RMBA-01 MUD BUS FOR C/F DRIVE MAKE - ABB/DANFOSS/SIEMENS THERMISTER FOR C/F DRIVE MAKE - ABB/DANFOSS/SIEMENS PLC MODULE DX 561 MAKE - ABB/DANFOSS/SIEMENS RINT CARD 5611 C FOR VFD MAKE - ABB/DANFOSS/SIEMENS RMIO CARD FOR VFD MAKE - ABB/DANFOSS/SIEMENS TIMER BLOCK FOR A9---75 TP401A 0.1-40 SEC. MAKE - ABB/DANFOSS/SIEMENS DCS 800M DCS-ABB IOS HARDWARE FOR - AI-40, AO-24, DI-48, DO-24, MAKE - ABB/DANFOSS/SIEMENS VFD (VARIABLE FREQUENCY DRIVE) 55 KW, MAKE - ABB/DANFOSS/SIEMENS STEAM FLOW DP TYPE TRANSMITER SERIAL NO.-OO416368 MODEL NO.-2051CD3A02A1AH2B1K5M5D4DF04, RANGE -0 TO 7500MMH2O MAKE - ROSE MOUNT/NEXUS/ABB/FORBES MARSHALL SUPPLY, ERECTION AND COMMISSIONING OF SYRUP SO2 BURNOR TEMPERATURE MONITOR WITH PANEL WITH ITS ERECTION HARDWARE, MAKE - ABB/DANFOSS/SIEMENS SUPPLY, ERECTION AND COMMISSIONING OF FURNACE PRESSURE TRANSMITTER AND ERECTION HARDWARE, MAKE - ABB/DANFOSS/SIEMENS SDCS POWER CARD DCS880 FOR MILL DRIVE MAKE - ABB/DANFOSS/SIEMENS RMBA-01 MUD BUS FOR C/F DRIVE MAKE - ABB/DANFOSS/SIEMENS THERMISTER FOR C/F DRIVE MAKE - ABB/DANFOSS/SIEMENS SCOPE OF SUPPLY : DESIGN, MANUFACTURING, SUPPLY, ERECTION & COMMISSIONING OF GRPF SYSTEM FOR MILL Ø33X66 1. GRPF ROLLERS WILL BE OF OUTSIDE DIAMETER 910 MM & 1700 MM SHELL LENGTH. 2. THE GRPF TOP & BOTTOM ROLLER WILL BE OF COARSE GRAIN CI SHELL SHRUNK FITTED ON SHAFT. TOP ROLLER WILL BE LOTUS. 3. THE SHAFT WILL BE OF 40C8 QUALITIES CONFIRMING TO IS: 1570 – 1979 OR EQUIVALENT, BEARING MIN. STRENGTH OF 58 KG/MM2. 4. THE ROLLER SURFACE WILL BE HARD FACED. 5. THE JOURNAL SIZE WILL BE MINIMUM DIA. 300 MM X 400 MM FOR GRPF ROLLER. 6. THE ROLLER WILL BE SUPPORTED ON CAST STEEL BEARING OF IS-1030 GRADE LL WITH GUN METAL BUSH. 7. GRPF TOP BRACKET, BOTTOM BRACKET & SIDE CAP WILL BE FABRICATED OUT OF IS: 2062 WELD-ABLE QUALITY 32 MM THICK. MILD STEEL PLATE. IT WILL BE STRESS RELIVED & MACHINED TO SUIT GRPF ROLLER. 8. SPACER & PACKING PLATES WILL BE PROVIDED IN BETWEEN TOP & BOTTOM ROLLER BEARING TO ADJUST THE SETTING BETWEEN THE GRPF ROLLERS. 9. PRESSURE CHUTE WILL BE MADE OUT OF 25 MM THICK MS PLATE OF IS:2062 QUALITY MATERIAL. INSIDE SURFACE OF PRESSURE CHUTE WILL BE LINED WITH 5 MM THICK STAINLESS STEEL PLATE OF AISI-304 QUALITY. THE PRESSURE CHUTE WILL BE SUITABLE REINFORCE TO WITH STAND MAXIMUM PRESSURE OF 7 KG/CM2. PRESSURE CHUTE WILL HAVE ARRANGEMENT TO CHANGE SETTING. 10. STATIC COLLAR WILL BE PROVIDED OF 25 MM THK M.S. PLATE WITH HARD FACING. 11. GRPF WILL BE DRIVEN BY 200KW AC VFD DRIVE THR PLANETARY GEAR BOX ATTACHED TO BOTTOM ROLLER, ( GEAR BOX – PREMIUM, MOTOR – MARATHON / CG / ABB, VFD – DANFOSS). WILL BE SUPPLY TAIL BAR COUPLING ARRANGEMENT FOR THIS DRIVE. 12. GRPF TOP ROLLER WILL BE DRIVEN BY CROWN PINION FROM GRPF BOTTOM ROLLER. 13. SURFACE SPEED OF GRPF ROLLER WILL BE ABOUT 30% HIGHER THAN MILL ROLLER SPEED. 14. EXISTING UNDER FEED ROLLER WITH BEARINGS & BRACKET WILL BE USED AS GRPF UNDER FEED ROLLER & WILL BE DRIVEN BY CROWN PINION FROM GRPF TOP ROLLER. 15. TOP ROLLER AND BOTTOM ROLLER COVERS OF 4 MM THK M.S. PLATE WILL BE PROVIDED.TERMS AND CONDITION :- 01. WORK WILL BE COMPLETEDIN THE SCHEDULE TIME (GIVEN BY CHIEF ENGINEER) 02. ALL TOOL AND TACKELS ie- HYDRA, CRANE, WELDING MACHINE,WELDING CABLE.CUTTING SET,SAFETEY ITEM ARE IN SCOPE OF CONTRACTOR/SUPPLIER. 03. ALL CONSUMABLES TO EXECUTE THE JOB/ WORK,ie - GAS,WELDING ELECTRODE etc. WILL BE CONTRACTOR SCOPE. 04. LODGING,UNLOADING,TRANSPORTATION WILL BE IN THE SCOPE OF CONTRACTOR. 05. IN THE CASE OF ANY CSUALTY/ ACCIDENT FACTORY MANAGEMENT WILL NOT BE RESPONSIBAL, ALL RESPOSIBLE OF SUPPLYER /CONTRACTORMAKE - ADITYA/ARYAN/RUSHIKESH DECORATIVE PAINT - ANTI CORROSIVE DECORATIVE ALUMINUM PAINT MAKE - BERGER / ASIAN/INDIGO DECORATIVE PAINT - ANTI CORROSIVE DECORATIVE ALUMINUM PAINT MAKE - BERGER / ASIAN/INDIGO DECORATIVE PAINT - ANTI CORROSIVE DECORATIVE GREEN PAINT MAKE - BERGER / ASIAN/INDIGO CHLORO RUBBER PAINT / EPOCSY CHEMICAL PAINT (WHITE) MAKE - BERGER / ASIAN/INDIGO CHLORO RUBBER PAINT / EPOCSY CHEMICAL PAINT (RED) MAKE - BERGER / ASIAN/INDIGO CHLORO RUBBER PAINT / EPOCSY CHEMICAL PAINT (SMOKE GRAY) MAKE - BERGER / ASIAN/INDIGO CHLORO RUBBER PAINT / EPOCSY CHEMICAL PAINT (LEMON YELLOW) MAKE - BERGER / ASIAN/INDIGO CHLORO RUBBER PAINT / EPOCSY CHEMICAL PAINT (GREEN) MAKE - BERGER / ASIAN/INDIGO CLEANING, WASHING,MAINTENANCE AND HYDRAULIC TESTING OF OIL COOLER OF MILLS. make - ESKAY HEAT EXCHANGERS PVT LTD/SUNRISE/MULTITECH ENGINEERS CLEANING, WASHING AND HYDRAULIC TESTING OF OIL COOLER OF FIBRISER. MAKE - ESKAY HEAT EXCHANGERS PVT LTD/SUNRISE/MULTITECH ENGINEERS CLEANING, WASHING,MAINTENANCE AND HYDRAULIC TESTING OF OIL COOLER OF TURBINE MAKE - ESKAY HEAT EXCHANGERS PVT LTD/SUNRISE/MULTITECH ENGINEERS ONE TIME SERVICING & TESTING TRAIL WITH TUBE REPLACEMENT (WITH NEW TUBE SUPPLY) OF TURBINE OIL COOLER HEAT EXCHANGER - 040118100, TYPE - ST-BEM, S.R. NO 21364, CAPACITY - 120 GSM, DESIGN PRESSOUR - SHELL SIDE - 9 KG PER CM SQR @ 100 DIGREE CENTIGRAGE TUBE SIDE - DESIGN PRESSOUR - 6KG PER CM SQR @ 100 DIGREE CENTIGRADE , WITH 320 COPPER TUBE ID - 14MM, OD - 17MM, THICKNEES - 1.5MM, TUBE LENGTH 2630 CM WITH INSTALATION, TESTING & TRAIL MAKE - ESKAY HEAT EXCHANGERS PVT LTD/SUNRISE/MULTITECH ENGINEERS ELECTROMAGNETIC FLOWMETER, SIZE: 4/100 MM, REMOTE VERSION WITH INTER CONNECTION CABLE, LINER: PTFE, OUTPUT: 4 TO 20 Madc, INPUT POWER: 220VAC, RANGE: 0 TO 250 TPH, MAKE -ABB/EMERSON/YOKOGAWA AMC , SERVICING AND OVERHAULING OF BOILER FEED PUMP TYPE MOTER DRIVE PANEL ABB TYPE ACS - 800-4-0360 AMC SERVICING WELDING MACHINE WITH SERVICE ENGINEER MAKE - ADOR SUPPLY ERECTION AND COMMISSIONING LEVEL SENSOR & TRANSMITTERS CABILARY TYPE PAN LEVEL SENSORS 6 NOS. CONDUCTIVITY SENSOR WITH TRANSMITTER FOR EACH PANS,SIZE SET OF 6 SENSORS MAKE- ABB SUPPLY ERECTION AND COMMISSIONING MASS FLOW METER CORIOLISSIZE 100 NB RANGE: 0 TO 200TPH NORMAL,INLET PRESSURE: 6,KG./CM2,50*C.MAX.TPR MAKE - ABB . SUPPLY ERECTION AND COMMISSIONING JUMBO DISPLAY DIGITALSIZE 4 LINEMAKE CURRENT HR. FLOW, PREVIOUS HR.FLOW TOTAL,IMBIBITION CURRENT & PREVIOUS HRS.,RETRANSMISSION 4-20 MADC. MAKE - ABB SUPPLY ERECTION AND COMMISSIONING JUMBO DISPLAY DIGITALSIZE 2LINEMAKE EXHAUST PRESSURE & EXHAUST TEMPERATURE MAKE - ABB SUPPLY ERECTION AND COMMISSIONING SIGNAL ISOLATOR DUAL CH.SIZE 4-20 MAMAKE INPUT 4-20MADC , DUAL OUTPUTISOLATOR MAKE - ABB/MASIBUS SUPPLY ERECTION AND COMMISSIONING BRIX SENSOR WITH TRANSMITTER MICROWAVESIZE 50 TO 100%MAKE PAN BRIX SENSOR TRANSMITTER FOR “A” MASSECUITE MICROWAVE TYPE MAKE - ABB/H&K SUPPLY ERECTION AND COMMISSIONING TEMPERATURE SENSOR WITH TX. SIZE 300 MM LENGTHMAKE TEMPERATURE SENSOR WITH TX.(RTD+TW+TTX) FOR BODY, CALENDRIA MAKE - ABB/PEPL SUPPLY ERECTION AND COMMISSIONING INJECTION WATER CONTROL VALVE BFL / GLOBE YSIZE 300MMMAKE BFLY/GLOBE REGULATING TYPE WITH VALVE POSITIONER & AIR REGULATORS,I/P CONVERTORS,MANUAL HAND WHEEL, POSITION FEEDBACK COMPLETE WITH ALL ACCESSORIES & COUNTER FLANGES.MAKE - ABB/I&S/UNIFLOW SUPPLY ERECTION AND COMMISSIONING FEED CONTROL VALVE PROPORTIONALSIZE 6MAKE FEED CONTROL VALVE (GLOBE REGULATING TYPE WITH MANUAL WHEEL & POSITION FEEDBACK MAKE - ABB/I&S/UNIFLOW SUPPLY ERECTION AND COMMISSIONING FEED CONTROL VALVE FOR PAN HEADER ON/OFF TYPESIZE 4/100 NB MAKE FEED CONTROL VALVE FOR PAN HEADER FEED CONTROL (OPEN/CLOSE GLOBE VALVE CYLINDRICAL OPERATED TYPE FOR EACH PAN WITH MANUAL HAND WHEELHEADER (4 NOS. FOR EACH PAN)) MAKE - ABB/I&S/UNIFLOW SUPPLY ERECTION AND COMMISSIONING VAPOUR STEAMING CONTROL VALVE FOR EACH PAN ON/OFFSIZE 6”MAKE VAPOUR STEAMING CONTROL VALVE FOR PAN STEAM WASHING (OPEN/CLOSE GLOBE TYPE FOR PAN ) WITH POSITION FEED BACK & MANUAL HANDWHEEL MAKE - ABB/I&S/UNIFLOW SUPPLY ERECTION AND COMMISSIONING HOT WATER CONTROL VALVE ON/OFFSIZE 3”MAKE HOT WATER CONTROL VALVE (OPEN/CLOSE GLOBE TYPE FORWITH MANUAL HANDWHEEL & POSITION FEEDBACK.MAKE - ABB/I&S/UNIFLOW SUPPLY ERECTION AND COMMISSIONING NON-CONDENSABLE CONTROL VALVE ON-OFFSIZE 2MAKE NON-CONDENSABLE (OPEN/CLOSE GLOBE TYPE FOR PAN WITH MANUAL HANDWHEEL & POSITION FEED BBACK MAKE - ABB/I&S/UNIFLOW SUPPLY ERECTION AND COMMISSIONING VACUUM BREAK VALVE PROPORTIONALSIZE 4MAKE VACUUM BREAK VALVE REGULATING GLOBE TYPE WITH MANUAL HANDWHEEL & POSITION FEEDBACK FOR PAN ) MAKE - ABB/I&S/UNIFLOW SUPPLY ERECTION AND COMMISSIONING AUTO/MAN FACILITY FOR PAN OPERATIONS SIZE MAKE PANEL-ENCLOSURE FOR PANS COMPRISING OF : HMI 10 FOR DISPLAY PARAMETERS, AUTO/MANUAL STATION FOR CONTROL VALVE-1NOS.,FOR REGULATING VALVES, SELECTORS SWITCHES-.PUSH BUTTONS TO OPERTATE PANS BY OPERTAOR IN MANUAL MODE. MAKE - ABB/RHYTHM SUPPLY ERECTION AND COMMISSIONING REDUNDANT DCS CPU FOR RIO PANEL SIZE MAKE AC800M,PM858 KO2 WITH BATTERY BACKUP AND ACCESSORIES, COMPLETE SET. MAKE - ABB SUPPLY ERECTION AND COMMISSIONING IOS HARDWARE WITH TERMINATION & FUES TBSIZE MAKE ANALOGUE INPUT MODULE,AI801 MAKE - ABB SUPPLY ERECTION AND COMMISSIONING IOS HARDWARE WITH TERMINATION & FUES TBSIZE MAKE ANALOGUE OUTPUT MODULE,AO801 MAKE - ABB SUPPLY ERECTION AND COMMISSIONING IOS HARDWARE WITH TERMINATION & FUES TBSIZE MAKE DIGITAL INPUT MODULE,DI801 MAKE - ABB SUPPLY ERECTION AND COMMISSIONING IOS HARDWARE WITH TERMINATION & RLY BORDSIZE MAKE DIGITAL OUTPUT MODULE,DO801 MAKE - ABB SUPPLY ERECTION AND COMMISSIONING COMMUNICATION ETHERNATE CABLE ,CAT6 OUTDOOR WITH RJ 45 CONNECTOR & ACCESSORIESSIZE MAKE - ABB SMOKE GRAY PAINT Make - Berger Paint/ Asian Paint/Nerolac Paint ALUMINIUM PAINT Make - Berger Paint/ Asian Paint/Nerolac Paint S.S. TUBE - ID/OD -98/102 MM , LENGTH -810 MM Divine Tubes/ Rajendra Matel/ Ratnamani/Remi tubes Bus Green Paint Make - Berger Paint/ Asian Paint/Nerolac Paint Post Office colour Red paint Make - Berger Paint/ Asian Paint/Nerolac Paint SKY BLUE PAINT Make - Berger Paint/ Asian Paint/Nerolac Paint TARPAULIN 60X60 TARPAULINE IN SIZE 60’x60’ Heavy Duty As per IS:7903@PGOI Make Only.HDPE(High Density Polyethlene Geomemberbrane Tarpaulin with 05 Layer 300 Micron, UV Treated(Ultra Violet) Stabilized, 100% water Proof, With Greater strength & Stiffness, Easy to Fabricate & Weld using Thermoplastic.Density-1600 Kg/m3. Temperature of Crystalization-111.90C. Melting Point-130.80C .Specific Heat Capacity – 1640 to 2400 J/Kg-k. MAKE - ONLY MANUFATURE HORIZONTAL BELT CONVEYER SIZE - WEIDTH -864 MM LENGTH - 25 MTR Size :- Width - 864 mm , Length - 25 mtr ,Height - 800 mm(Agitator Side) Height - 1000 mm (Drive Side) Gear box with Motor - Model MIB - 304/1325 -4/38 Sr. No. - 131204000039287 Motor - RPM - 1455 , HP - 7.5 hp , KW - 5.5 kw MAKE - DYNAMIC RUBBER/ SIMPLEX ENGGINEERING / ROHAN ENGGINEERING/STITCH EXPERTS(INDIA) BELT STAICKER ( TRUCK UNLOADEER ) HEIGHT ( DRIVE SIDE ) - 1250 MM HEIGHT - 85 MM BELT TYPE - 3 PLY Belt Stacker (Truck Unloader) Height ( Drive Side) - 1250 mm, Height - 85 mm Belt Type - 3 Ply, Belt Width - 500 mm, Staicker Width - 700 mm, Length of Staicker - 5400 mm Primium Worm Reducer - Type - A 237 , Ratio - 30/1,Sr. No. - 6R 94060 Motor - RPM - 1410, kw - 1.1, Hp -1.5 MAKE - DYNAMIC RUBBER/ SIMPLEX ENGGINEERING / ROHAN ENGGINEERING/STITCH EXPERTS(INDIA) FOOD GRADE EPOXY COATING LIGHT GRAY PAINTt Make - Berger Paint/ Asian Paint/Nerolac Paint Installization of Mechanical Circulator in 60 MT Pan & trail and Testing Lumsum Mechanical Circulator for Pan(60 Ton):- Specification- Motor 45 KW/STD/IE2 Motor.RPM-52 RPM.Impeller -Wide Blade Hydraulic 1875 mm.MOC-40 gm, Electrical Panel with Complete System. MAKE - SPRAY ENGGENERRING / ENVISION ENGINEERING SOLUTION / UTTAM ENGG. Installization of Mechanical Circulator in 80 MT Pan & trail and Testing Lumsum Mechanical Circulator for Pan(80 Ton):- Specification- Motor 45 KW/STD/IE2 Motor.RPM-52 RPM.Impeller -Wide Blade Hydraulic 1875 mm.MOC-40 gm, Electrical Panel with Complete System. MAKE - SPRAY ENGGENERRING / ENVISION ENGINEERING SOLUTION / UTTAM ENGG. ETP upgradation online monitoring system 1.Modification/Repairing/Maintenance work of pipe line from inlet source to the end source of the final utility system (Air, Water & Chemicals)2. Oil Skimmer Specification: Belttype, Oil recycle rate– 10LPH,Capacity: 1-10 LPH, RPM=14003.Chemical dosing pump with VFD- and Repairing/Servicing for sludge drainage system. Specification: Nos. 3,Centrifugal type/Pneumatic/PPpump, Capacity-500-600 LPH, Head=5-25m, Pressure=4kg/cm2,4. Bio-cultural and MBBR media required for MBBR Tank. MBBR Specification:PP media high protected surface area, Dimension range-19mm-80mm long, Dia- 25x10 mm or closer, Wide ratio: minimum 78%, density=0.8- 1gm/cm3, MOC- PP/PVC5. Tube settling tank fillsSpecification:MOC–Pvc, Shape-hexagonal chevaron, Hydraulic radius-1.5cm,Angle of Inclination- 60 degree6. Screw press and pump systemSpecification: Motor capacity:1-2 HP, suction pressure 0.5-10 bar,delivery pressure upto16 bar. Type: rotary /positive displacement, flow rate: 0.6- 10 m3/hr7. Media requirement for drying bed. Specific MAKE- ION EXCHANGE/NALCO/AAKAR ENGINEERING/MANUFACTUR /AUTHORIZED DEALER Batch Vacuum Pan 80 Mt Capacity Capacity : 80 T, Type : Low Head, Boiling : ‘A’ Massecuite, Surface / Volume Ratio : 6.6, Ligament Of Holes : 16 Mm (Minimum) With Diamond Pitch, Tube Size : 102 Od X 1.2 Thk X 800mm Long, Tube Materials : S.S 304 Bottom Cone : `W’ Bottom Cone With Pneumatic Discharge Valve 600 mm Dia-2 No Support : skirt type shell support shall be provided, catchall : M. S. Fabricated catchall centrifugal type with UmbrellaTechnical specification :- capacity : 80 t, quantity : 1 no, volume : 560 hl, heating surface area : 370 m2, tube size : 102 od x 18 swg x 800 long, tube materials : s.s 304 quality, annealed, total no. Of tubes : 1640 nos. Plate thickness :- calendria shell : 18 mm, body shell : 18 mm, down take shell : 16 mm, bottom cone : 22 mm x 18 deg, top cone : 18 mm x 30 deg, tube plate : 32 mm, catchall : external - 12 mm, internal - 10 mm, vapour inlet : 10 mm, vapour outlet : 10 mm. Overall dimensions :- Calendria Dia : 6250 Mm, Body Shell Dia :6250 Mm, Down Take Dia : 2400 Mm Strike Level : 1000 Mm App, Make NR Febricators & Errectors/Dewoo Engineering/Uttam Engineering/Shrijee Stagging And Structure of 80 Ton Pan Erection & Fabraction Stagging And Structure of 80 Ton Pan Erection & Fabraction, IncludingTube Fitting Work. Make NR Febricators & Errectors/Dewoo Engineering/Uttam Engineering/Shrijee Receiving Crystallizer 90 MT Capacity Receiving Crystallizer 90 MT Capacity :- Technical Specification :- Description units technical specification :- quantity nos. 1 no, capacity tons 90, material of construction m.s. Fabricated of `u’ shaped construction mounted horizontally, support stools supports shall be provided. Thickness :- shell mm 16 , end plates mm 20 with stiffeners ismc 150, center shaft : fabricated central shaft of 600 dia x 12 thick fitted with 40c8 solsid shaft at both ends, stirrer : elliptical ribbon type stirrer made out of 25mm thick, 150 mm wide t joint, stirrer speed rph 60, stuffing box : stuffing box with gland packing will be provided, overall dimensions :- length mm 8000 mm ( approx), width mm 3060 mm ( approx), height mm 3500 mm ( approx). Drive arrangement : - motor hp 7.5 hp x 1440 rpm, planetary reduction gear box : top gear / kavistu make, size : suitable, valves and fittings :- masecuite discharge valve, type : fabricated sliding valve, size : 300mmdia , drain : 150mmdia fabricated nipple x 1 nos Make NR Febricators & Errectors/Dewoo Engineering/Uttam Engineering/Shrijee Stagging And Structure of 90 Ton Receiving Crystallizer Stagging And Structure of 90 Ton Receiving Crystallizer Including Erection & Fabraction. Make NR Febricators & Errectors/Dewoo Engineering/Uttam Engineering/Shrijee Black Bitmin Black Paints(Heat resistant) Make - Berger Paint/ Asian Paint/Nerolac Paint Anti Sulphuric White Paint Make - Berger Paint/ Asian Paint/Nerolac Paint Food Grade Enamal White Paint Make - Berger Paint/ Asian Paint/Nerolac Paint Electric Type Hot Air Generating System for Sugar Gross Hopper. Size-1.5 Mtr width Complete system with trial. Make - J.J. Engineering/Excel sugar system/Expert machinest. Condenset Pump With Motor, Cap. 50 m3/Hr. Head- 50 m Make - Sintech Condenset Pump With Motor, Cap. 60 m3/Hr. Head- 40 m Make - Sintech Condenset Pump With Motor, Cap. 40 m3/Hr. Head- 30 m Make - Sintech Condenset Pump With Motor, Cap. 10 m3/Hr. Head- 30 m Make - Sintech Condenset Pump With Motor, Cap. 5 m3/Hr. Head- 30 m Make - Sintech TARPAULINE IN SIZE 60’x90 Heavy Duty As per IS:7903@PGOI Make Only.HDPE(High Density Polyethlene Geomemberbrane Tarpaulin with 05 Layer 300 Micron, UV Treated(Ultra Violet) Stabilized, 100% water Proof, With Greater strength & Stiffness, Easy to Fabricate & Weld using Thermoplastic.Density-1600 Kg/m3. Temperature of Crystalization-111.90C. Melting Point-130.80C .Specific Heat Capacity – 1640 to 2400 J/Kg-k. MAKE - ONLY MANUFATURE SUGAR BAG STACKER (MOBILE TYPE) 1-Material to be coveyed-sugar bag(50kg),2-Type of conveyor-belt type,3 Capacity-800 bags/hr,4 Height of stacking-10 meter for 50 kg bags, 5.Rubber Belting(chevron cleated type)-650mm wide,M-24 grade N-M, 315/3-1,5,3-ply Make-DURA,HINDUSTAN,INDO NATIONAL,INDUS, 1st Part:-6.Length Of Boom-5.0 meter, 7.Head pulley(Rubberized)-Q-315x750 mmfacee,Shaft at bearing point Q-60, bearing Make-SKF/FAG, 8. Tail Pulley-Q-315x750 mmfacee,Shaft at bearing point Q-55, bearing Make-SKF/FAG, 9. Idlers A-Carrying-Q-76.1X 750,Bearing 6204 zz, make SKF/FAG spacing-450 mm B-Return-Q-76.1X 750,Bearing 6204 zz, make SKF/FAG spacing-3000 mm,10.Hosting & Lowering Arran(Worn and Worn sheel type)-50:1,5 Module driven wench with 12mm wire rope 6 x 37(manual), 11.Wheel -A-Pnumatic Wheel-600 x19. 02 Nos ADV wheel, B-Casterval wheel-3 x 8 -02 Nos Revolving Wheel, 12. Drive Details- A- Motor with starter-3 HP/1440 rpm Make-ABB/Slemens,COL,Bharat Bijali, B-Gear Box-U-400 Make-Elecon, Greaves, C-Input Coupling-Tyre Type, F-60, D.Out put coupling-Through chain & Sprocket, 13.Supporting Structure-MS-as per IS-2062, MS Fabricated with plate, chanel, angles with supporting chanel o 50 mm x 50mm x 6mm angle, Head frame-150 mm x x65mm x 6mm chanel, boom-125mm x 65mm x 6mm angle,2nd Part:-6.Length Of Boom-10.0 meter, 7.Head pulley(Rubberized)-Q-315x750 mmfacee,Shaft at bearing point Q-70, bearing Make-SKF/FAG, 8. Tail Pulley-Q-315x750 mmfacee,Shaft at bearing point-, bearing Make-SKF/FAG, 9. Idlers A-Carrying-Q-76.1X 750,Bearing 6204 zz, make SKF/FAG spacing-450 mm B-Return-Q-76.1X 750,Bearing 6204 zz, make SKF/FAG spacing-3000 mm,10.Hosting & Lowering Arran(Worn and Worn sheel type)-50:1,8 Module driven wench with 12mm wire rope 6 x 37 with geared motor & Elect panel & limit switch(Powerized), 11.Wheel -A-Pnumatic Wheel-600 x19. 02 Nos ADV wheel, B-Casterval wheel-600 x19. 02 Nos ADV wheel, 12. Drive Details- A- Motor with starter-5 HP/1440 rpm Make-ABB/Slemens,COL,Bharat Bijali, B-Gear Box-U-500 Make-Elecon, Greaves, C-Input Coupling-Tyre Type, F-60, D.Out put coupling-Through chain & Sprocket, 13.Supporting Structure-MS-as per IS-2062, MS Fabricated with plate, chanel, angles with supporting chanel o 50 mm x 50mm x 6mm angle, Head frame-150 mm x x65mm x 6mm chanel, boom-125mm x 65mm x 6mm angle, 14. Carrying rollers and return roller of suitable size and number are fitted with proper space to run the belt smoothly., 15.Paint the structure of both parts of stacker with one coat of red oxide and one coat of enamel smole gray paint., 16.Supplier to be submit the drawing of both parts of stacker for approval with in 10 days after issue the PO. MAKE - DYNAMIC RUBBER/ SIMPLEX ENGGINEERING / ROHAN ENGGINEERING/STITCH EXPERTS(INDIA) BLACK PAINT MAKE BERGER Make - Berger Paint/ Asian Paint/Nerolac Paint Golden Yellow paint Make - Berger Paint/ Asian Paint/Nerolac Paint PRIMAR RED OXIDE PAINT Make - Berger Paint/ Asian Paint/Nerolac Paint
