Tender For Provn Of 01X Or’S Living Accn For D & E Coy At Kiari Area Under Ge 860 Ews. ; 1 Surface dressing n exc 15 cm deep in soft /loose soil complete all as specified and directed by Engr-in-Charge. 2 Excavating in post holes (or similar holes) each n. exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25 cm complete all as specified and directed by Engr-in-Charge. 3 Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, laying of cables/pipes etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out in hard /dense soil complete all as specified and directed by Engr-in-Charge. 4 Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed by Engr-in-Charge. 5 M&L for Cement concrete type D2 1:4:8 (using 40 mm graded crushed stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed by Engr-in-Charge. 6 M&L Cement Concrete Type-B1 1:2:4 (using 20 mm graded crushed stone aggregate) as in foundations, including rafts, footings complete all as specified and directed by Engr-in-Charge. 7 M&L forReinforced cement concrete (nominal mix) 1:2:4(using 20 mm graded crushed stone aggregate) in chajjas complete all as specified and directed by Engr-in-Charge. 8 M&L for formwork to Rough finishedsurfaces concrete chullah hoods, chajjas, troughs and similar items including edges complete all as specified and directed by Engr-in-Charge. 9 S&FMild steel TMT bars 10 mm dia and over Fe-410 W(Gde E 250) cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engr-in-Charge. 10 M&L for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1998 grade St-240 complete all as specified and directed by Engr-in-Charge. 11 M&L for steel work in roof trusses (framed ) trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam,tee,angle,channel or flat sections) including distance pieces cleats etc complete all as specified and directed by Engr-in-Charge. 12 M&L for Pre-cast cement concrete block masonry type C-1 1:3:6 (using 20 mm graded crushed stone aggregate) with solid blocks, exc. 10 cm in width and setting in mortar 1:6 complete all as specified and directed by Engr-in-Charge. 13 M&L for Hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed by Engr-in-Charge. 14 M&L PCC type C1 75 mm thick 1:3:6 (using 20 mm graded aggregate crushed stone aggregate) as in Plinth protection laid in alternate bays (not exc 2 Sqm each) finishing even smooth at top without using extra cement and providing joints throughout the thickness of plinth protectio, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed by Engr-in-Charge. 15 M&L for Cement Concrete type D-2, 1:4:8 (using 20 mm graded crushed stone aggregate) 100mm thick as Sub base complete all as specified and directed by Engr-in-Charge. 16 M&L for coloured joint free Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm screed bed in CM 1:6 complete all as specified and directed by Engr -in-Charge. 17 M&L for Glazed ceramic tiles 450x300x7mm thick coloured/shaded as in vertical surfaces such as skirting dados etc set and jointed in neat cement slurry and pointed in coloured cement to match the surface with 10 mm thick rendering (1:4) complete all as specified and directed by Engr -in-Charge. 18 M&L for 2nd class hardwoodPlain, solid, straightchowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinnedat joints complete all as specified and directed by Engr -in-Charge. 19 M&L for Factory made shutter 35 mm thick 2nd class hardwood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressuretreated all as specified and directed by Engr-in-charge. 20 M&L for 30mm thick Second class hard wood Glazed and skeleton windows,ventilators open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc.sizes of members of shutters as specified in SSR Part I, Section 8 Clause 8.24(a) complete all as specified and directed by Engr -in-Charge. 21 S&F 3.00 mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, all as specified. 22 S&FFigured glass, pin head type 3 mm thick, confirming to SI-5437 (1969)and glazing with oil putty in squares n exc 0.5 sq. m in each pane all as specified. 23 M&L for Providing, cement concrete in hold fasts, roof kerbs or mud stops, rounded or chamfered on edges type B1 1:2:4 (using 20mm graded crushed stone aggregate) complete all as specified and directed by Engr-in-Charge. 24 S&F MS flat iron of size 25x3 mm as in hold fast conforimg to Fe 410-0 or Fe-310-0 complete all as specified and directed by Engr -in-Charge. 25 M&L for 15 mm thick cement plaster in cement mortar 1:6 on brick or concrete surface of walls and finished surface even and smooth without using extra cement complete all as specified and directed by Engr -in-Charge. 26 M&L for Rendering 15 mm thick on fair faces of brick wall or cement concrete surface in cement mortar 1:4 finished surface even and smooth without using extra cement complete all as specified and directed by Engr -in-Charge. 27 S&F 100 mm size extruded alluminium alloy with galvanised mild steel hinge pin type C-21 all as specified and directed by Engr in charge. 28 S&FAluminium anodised, barrel tower bolts of extruded section with 150 mm long bolt and fixed all as specified 29 S&F Aluminium handles, cast type, anodised 125 mm size complete all as specified 30 S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, 250 mm long 31 S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, 150 mm long complete all as specified and directed by Engr -in-Charge. 32 S&F 0.50 mm thick Pre- painted galvalume aluminum zinc coating GI based corrugated sheet in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as directed by Engr-in-Charge. 33 S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheeting 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws/J hooks and bolts as reqd complete all as specified and directed by Engr -in-Charge. 34 S&F Viterous China wash hand basin with pedestal coloured, flat back of 550 x 400 mm including brackets, cutting for and pinning the ends of brackets or erecting stands also including brass chromium plated waste coupling 32mm dia, PVC flexible waste pipe of 750mm long complete all as specified and directed . 35 S&F vitreous China squatting pan orrisa pattern white colour of size 580x440mm with integral foot rests includingprovision of lime concrete including P/S traps complete all as specified and directed by Engr -in-Charge. 36 S&F of PVC (Plastic polymer Cistern) low level white flushing cistern 10 litre capacity valve less, syphonic action type, complete with inlet, ball valve, float valve, bends, brackets, brass screws, handle etc and S & F of 32 mm dia PVC flush pipe of suitable length and making all connection complete all as specified and directed. 37 S&F 600mm x 450 mm bevelled edge mirror of selected quality glass mounted on 6mm thick AC building boardfixedon wall with wooden plugs with chromium plated brass screw & cup washer complete all as specified and directed by Engr -in-Charge. 38 S&F rotational moulded polyethylene water storage tank (cylindricalvertical with closed top) hoisted and jointed in position all as specified in SSR Part-I (1000 ltr capacity) including dismantling existing tank and providing all necessary fittings for connecting with pipe line, metal lockable cover complete all as specified and directed by Engr -in-Charge. 39 S&F 16mm bore 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors complete all as specified and directed by Engr -in-Charge. 40 S&F 20mm bore 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors complete all as specified and directed by Engr -in-Charge. 41 S&F 20 mm bore Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed by Engr -in-Charge. 42 S&F 20 mm bore ball valves high pressure PTMT with epoxy coated aluminium rod & high densityplastic ball screwed for iron pipe and fixed complete all as specified and directed by Engr -in-Charge. 43 S&F 15mm bore pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed by Engr -in-Charge. 44 S&F 15mm bib taps, fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed by Engr -in-Charge. 45 S&F brass chromium platedtubular towel rail 20mm dia600 mm long fixed complete all as specified and as directed. 46 S&F 75 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joint laid in trenches or in floors complete all as specified and directed by Engr -in-Charge. 47 S&F 110 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joint laid in trenches or in floors complete all as specified and directed by Engr -in-Charge. 48 M&L forPVC (SWR) 110 mm gully trap setting joining with solvent cement complete all as specified and directed. 49 S&F PVC connection15mm size with PTMT nuts of length 450mm fixed complete all as specified and directed. 50 S&F in repair PTMT waste grating doom with waste hole 100mm dia complete all as specified and directed by Engr -in-Charge. 51 S&F angle/stope valves 15mm bore (for iron pipe)fancy type PTMT any colour screwed down high pressure with butterfly handle screwed both ends complete all as specified and directed by Engr -in-Charge. 52 M&L Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes etc. with riveted, bolted or welded attachment confirming to Fe 410-W (Gde E-250), complete all as directed by Engieer-in-charge. 53 M&L for Mild steel bolts neck exc 10 mm dia and n exc 15 mm dia, purpose made, with hexagonal or square head one end and screwed the other, or screwed both ends; each scre-wed end to be fitted with washers and one hexagonal or square nut, exc 5cm but n exc 10cm long complete all as specified and directed by Engr -in-Charge. 54 M&L for preparation of new steel surfaces of any description over 10 cm width or girth not otherwise described and treating with two coats of synthetic enamel paints over a coat of red oxide primer complete all as specified and directed by Engr -in-Charge. 55 M&L for Preparing newly plastered surfaces of walls and applying two coats of cement base paint with one coat of primer complete all as specified and directed by Engr -in-Charge. 56 M&L for Preparing new surface of wall of any description and applying two coats of distemper oil emulion with one coat of primer complete all as specified and directed by Engr -in-Charge. 57 M&L for Preparation of new wooden or wood based Surfaces of any description, not otherwisedescribed, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed by Engr -in-Charge. 58 M&L for Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces;6 mm thick ( 5 Nos of ply) fixed with nails to timber frame work as in walls complete all as specified and directed by Engr -in-Charge. 59 M&L for Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one faces; 4 mm thick ( 3 Nos of ply) fixed with nails to timber frame work as in ceiling complete all as specified and directed by Engr -in-Charge. 60 M&L second class hard wood timber scantling plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads, sectional area exc. 6 Sq cm n.exc 13 Sq cm complete all as specified and directed by Engr -in-Charge. 61 Excavating over areas, n exc 1.5 m deep and getting out in hard/dense soil complete all as specified and directed by Engr -in-Charge. 62 Excavating over areas,exc 1.5 m and n.exc. 3.00m deep and getting out in hard/dense soil complete all as specified and directed by Engr -in-Charge. 63 M&L for Walling of random rubble stone masonry, uncoursed, well bonded, bedded and solidly hearted, build in cement mortar 1:6 complete all as specified and directed by Engr -in-Charge. 64 M&L for Walling of random rubble, uncoursed, well bonded, laid dry in retaining walls, abutments and similar work complete all as specified and directed by Engr -in-Charge. 65 M&L for reinforced cement concreteType B1 1:2:4using 20mm graded crushed stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed by Engr -in-Charge. 66 M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) etc rough finished surfaces of concrete complete all as specified and as directed. 67 M&L for formwork Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm widerough finished surfaces of concrete complete all as specified and as directed. 68 M&L for precast reinforced cement concrete 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in cover slab for manholes set in CM 1:4 including necessary form work complete all as specified and directed by Engineer in Charge. 69 Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cms complete all as specified and directed by Engr -in-Charge. 70 M&L Concrete bed 1:4:8 type D-2( using 40mm graded crushed stone aggregate)to drain pipes incl packing under and haunching against the sides of pipes after they are laid and tested bore of pipe in 150 mm complete all as specified and directed by Engr-in-Charge. 71 S&F150mm dia, PVC (SWR) pipes single socketed,inanylength with rubber ring joints, laid in trenches or in floors complete all as specified and directed by Engr -in-Charge. 72 M&L for Rendering 15mm thick in CM 1:4 on fair faces ofstone surface work with water proofing compound @ 3% by weight of cement including finishing the surface even and smooth without using extra cement complete all as specified and directed by Engr -in-Charge.Note : WPC shall be measured and paid seperately. 73 Supply only Integral Water proofing compound. 74 M&L for loose filling with broken stone or boulders of gauge nexc 63mm in soakage pit, soakage wells complete all as specified and directed by Engr-in-Charge. 75 Material and labour for point wiring with 1.5Sqmmcopper conductor (Multi-standard) PVC insulated andunsheathed electric cable 1100 voltsin and includingPVC casingand cappingof 25 mm and above (as per conductor run )with all fittings/ accessories and including PVCinsulated and unsheathed electric cable1100 volts1.5 Sqmm ( multi-stranded)copperconductor single core( Green colour) cable as continuous earth wire connected to common earth dollyincluding50 mm deep box made of 2nd class hard board of requiredsizeand shape etc covered with 3 mmthick plastic laminated sheet ( Make Hylum) forone lightpoint,bell,exhaust point, bulk head, independent controlled by one, one way switchcomplete all as specified and as directed by the Engineer-in-Charge. 76 Description all as per Srl item No. 75.00 here-in-before but for one socket outlet 3 pin, 5 Amps on independent board. 77 Description all as per Srl item No. 75.00 here-in-before but for one socket outlet 3 pin, 5 Amps on same board. 78 Description all as per Srl item No. 75.00 here-in-before, but for one socket outlet 15 Amps on independent board with 2.5 Sqmm copper conductor (Multi-stranded) insulated and unsheathed electric cable 1100 volts (ISI Marked) including PVC insulated and unsheathed electric cable 1100 volts 1.5 Sqmm copper stranded conductor as continuous earth wire connected to common dolly complete all as specified and as directed by Engineer-in-Charge. 79 Supply and fixing switch piano flush button single pole one way5 Amps complete all as specified and as directed by Engineer-in-Charge. 80 Supply and fixingsocket2 in 1, 5 Amp, flush type complete all as specified and as directed by Engr-in-charge. 81 Supply and fixing switch socket combination multi purpose 2 in 1, 3 pin 5A/16A, 5 in 1 flush type complete all as specified and as directed by Engr-in-charge. 82 Supply and fixing angular lamp holder, PVC/Polycaronate type with back plate suitable for 9/12 watt LED bulb forbatten fittings complete all as specified and directed by the Engineer-in-Charge. 83 Supply and fixing LED 12 Watt complete all as specified and as directed by Engineer-in-Charge. 84 Supply and fixing ceiling rose, surface bakelite, 65 x 50 mm, three terminals complete all specified and as directed by the Engineer-in-Charge. 85 Supply and fixing LED batten lights fitting 1x 20W, 220V,AC decorative type including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed by Engineer-in-Charge. 86 S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by the Engineer-in-Charge. 87 Supply and fix exhaust fan made of study Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and directed by the Engineer-in-Charge. 88 S&F DB, Single Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed. 89 S&F DB, Single Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, SPN 4 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed. 90 Supply and fixing MCB single pole and neutral 32 to 40Amps , 240 volt, 10 KA,complete all as specified andas directed by the Engineer-in-Charge. 91 Supply and fixing MCB single pole 6 to 32 Amps, 240 volts, 10 KA complete all as specified and as directed by the Engineer-in-Charge. 92 Supply and fixingLED luminaire 600 mm x 600 mm, 40 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling 6500K including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and directed by the Engineer-in-Charge. 93 Supply and fixingnew energy saving LED Bulk head fitting 10 watt made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP 66 protection and impact resistance of IK07as reqd to be mounting bracket in wall/floor to suit the opening of the fitting with FI clamp, nut, bolt and washers of suitable size including making connection complete all as specified and as directed by Eng-In-Charge. 94 Earthing complete withgalvanized steel earth plate electrode 60 cmx 60 cm x 6 mm thick buried directlyin ground (earth pit notless than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metres below normal ground level,connecting to theGalvanized ironearth wire 4.0 mm dia by means of bolts, nuts , check nuts and washers of galvanized iron andsteelearth wire protected by provision of GI lightgrade pipe15 mmbore including provision of concrete pitmade from PCC ( 1:2:4) type B-1 (using20 mm graded stone aggregate) with 40mm thick cover of RCC 1:2:4 reinforced with XPM (Weight not less than 4 Kg/Sqm) and frame of angleiron40 x 40 x 6 mm and handle of 6 mmdia MS barmade to shape, GI light grade 20 mmbore pipefor watering perforated atbottom, 1.50metre long placed on top edge of earth plate, common salt &charcoalfilling, withfixing arrangement , funnel, wire mesh and earthwork in hard/dense soil, returning filling in and removal of surplus soilto a distance notexceeding50 metres, all as perelectrical plate No 3 of SSR 2009 Part-I and connecting toCBDB’s as specified or indicated including testing on completion complete all as specified and as directed by Engineer-in-Charge. 95 Supply and laying XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor 1100 V grade nominal cross sectional area 16 Sqmm, 2 core laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/floors/equipment etc including jointing and testing complete all as specified and directed by the Engr-in-Charge. 96 Material and labour for un-reinforced pre-cast concrete cable covers, class LV type-1, flat size 250mm x 150mm x 40mm thick complete all as specified and directed by Engr-in-Charge. 97 M&L for sand cushioning with layer of sand 8cm thick before laying of cable and 15cm after laying, streching & testing of cable in trenches complete all asspecified and directed by Engr-in-Charge. Note :- Only punned thickness i.e 18cm shall be measured and paid.
