}

Tender For Additional / Alternator To Or Lines Bldg No. T-25 Of Mtn Dou And Other Rev/ Minor Works At Under Ge (East) Bareilly, bareilly-Uttar Pradesh

Statutory Bodies & Commissions/Committees has published Tender For Additional / Alternator To Or Lines Bldg No. T-25 Of Mtn Dou And Other Rev/ Minor Works At Under Ge (East) Bareilly. Submission Date for this Tender is 14-10-2024. Wrenches and Drivers Tenders in bareilly Uttar Pradesh. Bidders can get complete Tender details and download the document.




Tender Notice

45252411
Corrigendum : Tender For Additional / Alternator To Or Lines Bldg No. T-25 Of Mtn Dou And Other Rev/ Minor Works At Under Ge (East) Bareilly
Open Tender
Indian
Uttar Pradesh
Bareilly
14-10-2024

Tender Details

Tender For Additional / Alternator To Or Lines Bldg No. T-25 Of Mtn Dou And Other Rev/ Minor Works At Under Ge (East) Bareilly; 1 Dismantling asbestos cement sheet (corrugated, semi corrugated, etc.) sheets in roof coverings complete all as specified and directed. 2 Dismantling timber scantlings 40 sq. cm and over in section, in any position as unframed work complete all as specified and directed. 3 Demolition of brickwork or stone/boulder masonry, built in cementmortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed. 4 M&L for fly ash brick work with old size bricks, straight or curved on plan exc 6m mean radius, built inCM 1:6 complete all as specified and directed. 5 M&L for fly ash brick work with old size bricks, straight or curved on plan exc 6m mean radius, built inCM 1:4 complete all as specified and directed. 6 S&F rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running railsand guides for sliding doors; fixed with angle cleats or other connecting plates Fe 410-W (Gde E- 250) quality A complete all as specified and directed. 7 M&L for preparation of new or previously untreated steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide or zinc chrome primer complete all as specified and directed. 8 Taking down Chowkats or frames with shutters (without taking off shutters from the frames) n.exc. 1.5 sqm each complete all as specified and directed. 9 Taking down Chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.50 sqm and n exc 4 sqm each complete all as specified and directed. 10 S&F 2nd class hardwood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed. 11 S&F 40 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. 12 S&F 35mm thick factory made glazed and skeleton door shutters open rebated of second class hard wood rail and styles (Hollock), prepared to receive glass/gauge etc without sash bars, edges of framing plain cham-fered or rounded, mitred and rebated sash bars, any numbers The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. 13 S&F 150 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed. 14 S&F 150 mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed. 15 S&F 100 mm MS butt hinges medium weight cold rolled mild steel complete all as specified and directed. 16 S&F 300 mm long mild steel chromium plated sliding door bolts, plate type, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed. 17 S&F mild steel spring 250mm for door, ordinary rat tail rod pattern springs, including roller and roller plate including welding as required for steel frame complete all as specified and directed. 18 S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tracks or wooden beeding patti complete all as specified and directed. 19 M&L for preparation of new or previously untreated of wood or wooden based surface exc. 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed. 20 M&L for powder coated aluminium sliding window with anodized aluminium frame of3 Track of size 92mm x 32mm x 1.5mm thick, with sliding shutters (02 glass and 01 wire cloth) with necessary channels (top rail, bottom rail and style of size 40mmx 18mm x1.10 mm thick) including glazing with tinted sheet glass panel 4.00mm thick and Aluminum alloy wirecloth avg width of aperture 1.4mm fixed outer side with necessary aluminium fillets, fitted with necessary jointing cleats, glazing clips, locking device one for each shutter, rubber packing, aluminium beading, screws, rawl plugs including all necessary holes/ drilling etc complete all as specified and directed.Note : If mentioned section are not available in market, then immediate next higher section shall be provided by the Contractor without any extra cost. 21 S&F aluminium powder coatedpartitionswith aluminium anodizedframe of size 90mm x 44mm x 1.6 mm thick fixed with screws including panels of any 18/19mm thick decorative both side prelaminated perticle board inretior grade upto ht 1.80 mtr abovetinted glass panels 5.5mm thick ofht 0.90 mtr , with necessary, jointing cleats, glazing clips, rubber packing, aluminiumbeading, screws etc complete all as specified and directed. 22 S&F pre-coated galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed. 23 Dismantling wall/ ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets complete all as specified and directed. 24 M&L for false ceiling with powder coated exposed G.I. grid suspension system (E-Grid T-2430 or equivalent load carrying capacity with mid span deflection not exceeding 1/360 span with hanger spacing of 1200 mm c/c) consisting of Main Runner 3600/3000 mm long, Cross Tee 1200mm/ 600mm long and Wall Angle. The Wall Angle shall be fixed on PVC Dash Fasteners on the perimeter of the wall by steel screws with distance 300 mm c/c. The Main Runners to be placed @ 1200mm, The Cross Tee 1200mm will be inserted in the pre-cut slots of Main Runner at a regular interval of 600 mm to form a modular grid of 1200mm x 600mm. Additional Cross Tees of 600 mm shall be placed perpendicular to the Cross Tee 1200 mm long to finally form a grid of 600mm x 600mm. Grid of module size 600mm x 600mm shall be supported by 3/4 mm dia G.I. wire from purlins/soffit. 4mm thick High Pressure Steam Cured Everest Non Asbestos Fibre Cement Ceiling tile Oceanic/Diamond textured (Density>1200 Kg/m3, Modulus of Rupture(M.O.R)-10 MPa, Thermal Conductivity (K)-0.02 W/mK) of size 595mm x 595mm, confirming IS 14862 & Type B Category III of ISO 8336:1993, (Reaction to fire-A2-s1-d0) tested as per EN13501 Part-I & BS-476 Part 4,5,6&7 should be placed in the Grid module to form a False Ceiling complete all as specified and directed. 25 M&L for 15mm thick rendering in cement mortar 1:4 on brick masonry surfaces of other than fair faces finished fair & even without using extra cement complete all as specified and directed. 26 M&L rendering 15 mm thick in CM 1:6 on brick masonary wall surfaces or on other than fair faces of brick masonry finished even and smooth without using extra cement complete all as specified and directed. 27 M&L for preparation newly plastered walls surfaces and applying two coats ofoil bound distemper over1mm thick wall care putty complete all as specified and directed. 28 M&L for preparation of newly plastered walls surfaces and applying two coats of cement base paint over a coat over one coat primer complete all as specified and directed. 29 M&L for complete removal of existing treatment of wall and applying two coats of putty, applying two coats of oil bound distemper any colour complete all as specified and directed. 30 Complete removal of existing treatment of wall and applying two coats of cement putty, applying two coats of exterior emulsion (weather proof) any colour complete all as specified and directed. 31 S&F in repair 20 mm dia stainless steel 1.0 mm thick fancy type SS curtain rods with decorative design matching brackets as approved and knobs (lattu) or end bracket as required& other all neccesary fittings fitted with SS screws etc on each end complete all as specified and as directed. 32 M&L for 1:2:4 reinforced cement concrete, type B1 nominal mix using 20 mm graded stone aggregate as inslabs supported on walls, beams and columns in floors, roofs, landings, shelves and the like complete all as specified and directed. 33 M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings,girders, bressummers,lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed. 34 M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide rough finished concret surfaces complete all as specified and directed. 35 S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. 36 M&L for mild steel TMT bars 6mm to 8mm dia cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming complete all as specified and directed. 37 M&L framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and directed. 38 M&L for coloured non skid ceramic tiles 7 to 8 mm thick of colour patteren as approved and as per manufacturers catalouge (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 Sqm, in floor etc including 15mm thick screed bed with cement mortar 1:6 and set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed. 39 M&L for coloured glazed ceramic tiles 300 mm x 450 mm x 7 mm thick on vertical surfaces of colour patteren as approved and as per manufacturers catalouge such as skirting, dados etc, set and jointed in neat cement slurry over and including 10 mm thick rendering in CM 1:4 and pointed in white or coloured cement to match complete all as specified and directed.Note : Skirting shall be provided to match with colour and size of floor tiles provided in rooms. 40 S&F solid PVC door frame of size 50 mm x 47 mm made out of 10 mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification & drawing complete all as specified and directed. 41 S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solventcement, suppling & fixing in the frame at site as per specification complete all as specified and directed. 42 S&F 100 mm Heavy duty aluminium powder coated butt hinges as approved as per sample complete all as specified and directed. 43 S&F 150 mm Heavy duty aluminium powder coated tower bolt as approved as per sample complete all as specified and directed. 44 S&F 150 mm Heavy duty aluminium powder coated Handle as approved as per sample complete all as specified and directed. 45 S&F in repair 15 mm bore dia of pipe pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Coldwith long screwed shanks and flynuts , screwed for iron pipe and fixed complete all as specified and directed. 46 S&F in repair 15 mm bore dia of pipe cast copper alloy CP angle valve type stop cock with flange screwed at both ends or high pressure with Capstan headconfirming complete all as specified and directed. 47 S&F in repair PVC connection 15mm size with PTMT nuts, of length 600mm complete all as specified and directed. 48 S&F 15 mm bore dia of pipe bib tap long body foam flow with flange, cast copper alloy, chromium plated,fancy type, with crutch or butter fly handle screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. 49 S&F 20 mm dia brass chromium plated tubular towel rail 60cm long with and including flanges complete all as specified and directed. 50 S&F soap dish stainless steel as approved by GE complete all as specified and directed. 51 S&F 600mm x 450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed. 52 S&F viterous china wash hand basin of size 550 x 400 mm, white colour flat back excluding taps, chain and plug and porcelean stopper but including brackets and CP waste fitting and 32 mm PVC waste pipe complete all as specified and directed. 53 S&F vitreous china wash down water closet pedestal pattern (EWC) white excluding flushing cistern & Inclwhite seat cover of same make closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device andflush pipe complete all as specified and directed. 54 S&F 10 litres capacity PVC Valveless symphonic action type flushing cistern high/ low level white complete with inlet, ball valve float and handle including brackets and telescopic down pipes and jointing with WC complete all as specified and directed. 55 M&L for 75 mm, dia PVC (SWR) floor trap, plain with SS grating including jointing to waste pipe fixed in cement concrete 1:2:4, type B-1 complete all as specified and directed. 56 S&F 40 mm bore dia low density polyethylene pipes (LDPE) of pressure rating 6 kg/ cm2 for wash hand basin complete all as specified and directed. 57 Supplying and laying of 20mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified and directed. Note : The rate includes for chase cutting of concealed for all the pipes shall be got tested before providing by pressure testing machine and got approved and any leakage seepage observed, the conctractor shall be redo the same without any extra payment. 58 Supplying and laying of 25mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified and directed. Note : The rate includes for chase cutting of Concealed for all the pipes shall be got tested before providing by Pressure testing machine and got approved and any leakage seepage observed, the conctractor shall be redo the same without any extra payment. 59 S&F 110mm bore dia PVC (SWR) pipes single, socketed in any length, with rubber ring joints fixed to walls with MS clamps complete all as specified and directed. 60 S&F 110mm bore dia PVC (SWR) bends complete all as specified and directed. 61 S&F 110 mm bore dia PVC (SWR) branch piece, double (double Y) equal or unequal complete all as specified and directed. 62 S&F 75mm bore dia PVC (SWR) pipes single, socketed in any length, with rubber ring joints fixed to walls and floor with necessary fitting complete all as specified and directed. 63 S&F 75 mm bore dia PVC (SWR) bends complete all as specified and directed. 64 S&F 75 mm bore dia PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and directed. 65 S&F aluminium powder coated frame for louvers section of size 75x40x1.6mm including 4mm thick glass in louvors of 100 mm width with glazing cleat and revolving arrangement of standard section of aluminium including rubber packing, aluminium beadingor gasket forfor aluminium sections for fixing glass sheet and necessary fittings complete screws plugs, handle, tower bolt, stay hooks including fixed Aluminium wire clothetc complete all as specified and directed. 66 Surface dressing n exc 15 cm deep in any type soil complete all as specified and directed. 67 Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and getting out in any type of soil completed all as specified and directed. 68 Returning filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm complete all as specified and directed. 69 Removing excavated material n exc 50m and depositing where directed at a level n exc 1.50M above the starting point complete all as specified and directed. 70 M&L for PCC 1:4:8 D-2 type (using 40mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed. 71 M&L for cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in coping complete all as specified and directed. 72 M&L for RCC 1:2:4 type B-1 (Nominal Mix) (using 20mm graded stone aggregate) as in foundation footing,Plinth, lintel/ roof beam complete all as specified and directed. 73 M&L for hard core broken brick gauge n exc 63mm, deposited spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed 74 M&L for 75 mm PCC 1:4:8 type D-2 (40 mm graded stone aggregate ) as in floor complete all as specified and directed. 75 M&L 40 mm thick PCC 1:2:4, type B1, 20 mm graded aggregate as in floor rough finished to receive top layer complete all as specified and directed 76 M&L for non- skid coloured ceramic tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile and including 15 mm thick screed bed or bedding layer of mortar, in cement mortar 1:6 complete all as specified and directed. complete all as specified and directed. 77 M&L for non- skid coloured ceramic tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed. complete all as specified and directed. 78 M&L 9 to 10 mm thick glazed coloured ceramic tiles (square/ rectangular) with border, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in vertical surfaces such as skirting or dado set & jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles complete all as specified and directed. 79 S&F aluminium alloypowder coated aluminium door frame fixed with side hung shutters and glazing fixed with and including 5 mm thick aluminium composite panel LDPE core PET coating (both side decorative type) fixed with rubber gasket with aluminium heading, clips frame made with aluminium box section complete all as specified and directed as appended below:-(a) Frame 100x44x1.48mm thick with rawl plug(b) Middle and lock rail : 150x44x1.48mm thick(c) Bottom rail : 150x44x1.48mm thick(d) Top rail/style : 85x44x1.48mm thick(e) Aluminium beading : 0.7mm thick(f) Aluminium handle D type 150mm long, aluminium tower bolt 9.9mm dia shoot 200mm long brass mortise lock 100mm 4 leaver , withS S hinges complete (g) Making good of wall surface to match with existing surface complete. 80 S&F powder coated aluminium ventilators box type with louvers & wire mesh fixed with neoprene rubber gasket, aluminium beading, clips. Frame made with powder coated aluminium section of size as appended below (i)frame :45.2mm x35mm X 1.15 mm(ii) Aluminium beading - 0.7mm thick(iii) Glass louvers depth 6 inch. Blade Angle: 38 degrees and thickness of blade 2.02 mm with 106.25 mm spacing.(iv) Aluminium neccessary fittings complete as required.(v) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed. 81 M&L for 75 mm thick cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in plinth protection finished even and smooth without using extra cement including forming necessary joints 12 mm wide to the full depth of PCC at every 3 metres and every change of direction and filling the same with & including bitumen and sand 1:3 by weightcomplete with and including necessary form work etc complete all as specified and as directed. 82 S&F vitreous chinaware coloured wash hand basin with pedestal of size 55X45X82cm complete including fancy CP pillar tap, CP Waste coupling ,waste pipe ,complete fixing arrangementand cutting for and pinningin walls & making good complete all as specified and directed. 83 S&F vitreous china bowl urinal flat back size 430x370x340 mm with grating and union for discharge pipe including flushing cistern flush pipe and waste pipe and all coplete acceries for urinal complete all as specified and directed. 84 S&F urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed. 85 S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes confirming to IS 1161-1979 complete all as specified and directed. 86 S&F 1000 litres, rotational moulded polyethylene of white colour in tripple layer water storage tank (cylindrical vertical with closed top with suitable size ofMS tasla with suitable locking system), hoisted and fixed in position complete all as specified and directed 87 S&F fancy type brass chromium plated soap dish of 160x160x90 mm complete all as specified and directed. 88 S&F 20mm bore ball brass valve high pressure with polythene float and fly nut complete, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. 89 S&F 15 mm dia fancy type stop cock, chromium plated with long shank and cup (conncelaed type) for iron pipe or for unions and fixed complete all as specified and directed. 90 S&F 15 mm dia steel tubing galvanized medium grade concealed in all type wallwith all fittings, fixed to walls and ceiling or in floor complete all as specified and directed. 91 S&F 20 mm dia steel tubing, galvanized, medium grade concealed in all type wallwith all fittings,fixed to walls and ceiling or in floor complete all as specified and directed 92 Taking down cement plaster on brick or stone walls, etc.including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed. 93 S&F powder coated aluminium sliding windows frame with movable shutter (sliding on minimum two PVC roller of best quality, for each shutter on three tracks with stainless steel mosquito proofing and glazing shutter and incl 5.00 mm thick glass & stainless steel wire mesh fixed with neoprene rubber gasket with aluminium beading, clips, frame made with aluminium section as appended below- (i) Window frame: 90x32mm X 1.15 mm thick for three tracks.(ii) Top/bottom rail and style / rail of shutter: 15x37.5x1.15 mm thick and over. (iv) stainless steel wire cloth 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed in aluminium window or alongwith F/Y section fixed with aluminium wire staples complete.(v)Aluminium fittings such aluminum suitable handle with auto interlock cap with suitable size.(vi) Making good of wall surfaces with silicon to match with existing surfaces complete all as specified and directed. 94 M&L for powder coated aluminum window/ doors grills fixingalong with frame of following specification, grills with opening 69.4mmX 78.2mm grills thickness shall be of 6.4mm X 5.8mm having weight not less than 2.306 Kg/per sqmshape as ordered with frame channel of34 X 11mm X1.7mm thick fixed with screw inside of the window complete all as specified and as directed. 95 Taking down carefully existing Aluminum/ Copper point wiring (light/ Fan / including switches/ sockets/ Power Point) complete fittings etc. making good to disturbed surface of wall/Floor etc to match the existing surface/ finishes complete all as specified and directed. 96 M&L for concealed point wiring for one light/ fan/ bell point controlled by one switch with 1.5 Sqmm (Nominal area) PVC insulated, unsheathed, stranded copper conductor cable FRLS (1100Volts grade) drawn in and including PVCconduits of 20 mm dia with all fittings and accessories alongwith PVC insulated cable with copper conductor of size 1.5 Sqmm FRLS as earth continuity conductor including fixing of 1. 2mm thick MS sunk terminal boxdulyflus complete all as specified and directed. 97 All as per item no.2 here in before but for socket outlet 3/5 pin 5 amp. on the same board. 98 All as per item No 02 here-in-before but for 5 Amps 3/5 Pinpoint on independent board 99 M&L for concealedpoint wiring with 2.5 Sqmm (Nominal area)PVCinsulated,unsheathed, multi stranded copper conductor FRLS cable drawn in and including PVC rigid PVC conduit 25mm or higher size with all its fittngs and accessories for one 3 pin/6 pin 15 Amps socket out let point independent alongwith PVC insulated cable with solid copper conductor 1.5 Sqmm FRLS (nominal area) continuous earth wire, and connected to earth dolly including fixing of 1.20mm sunk pressed steel terminal box suitably flushedto wall with 3mm thick Hylum sheet cover fixed with screws & cup washers incl. making good complete all as specified and directed. 100 S&F modular white cover plate with frame, 1 module complete all as specified and as directed. 101 S&F modular white cover plate with frame, 2 module complete all as specified and as directed. 102 S&F modular white cover plate with frame, 3 module complete all as specified and as directed. 103 S&F modular white cover plate with frame, 4 module complete all as specified and as directed. 104 S&F modular white cover plate with frame, 6 module complete all as specified and as directed. 105 S&F modular white cover plate with frame, 8 module complete all as specified and as directed. 106 M&L modular metal flush box 1/2 module complete all as specified and directed. 107 M&L modular metal flush box 3 module complete all as specified and directed. 108 M&L modular metal flush box 4 module complete all as specified and directed. 109 M&L modular metal flush box 6 module complete all as specified and directed. 110 M&L modular metal flush box 8 module complete all as specified and directed. 111 S&F modular switches 1 way, 6 A, 1 module complete all as specified and directed. 112 S&F modular switches 1 way, 16 A, 1 module complete all as specified and directed. 113 S&F modular sockets6 A,-2/3 pin combined2 module complete all as specified and directed. 114 S&F modular sockets6 A/ 16 A, 2/3 pin combined2 module complete all as specified and directed. 115 S&F switch piano flush type single pole one way 5 Amps complete all as specified and directed. 116 S&F switch Piano flush type single pole one way 15 Amps complete all as specified and directed. 117 S&F socket outlet 2 in 1, 3 pin 5 Amp flush type complete all as specified and directed. 118 S&F socket outlet 2 in 1, 3 pin 5Amp and 15 Amp complete all as specified and directed. 119 M&L for ceiling rose, 3 phase/ PVC/ polycarbonate, isolated body complete all as specified and directed. 120 S&F lamp holder (batten/ angle) PVC/polycorbonate type with back plate for batten/ angle fittings complete all as specified and directed. 121 S&F lamp LED Adore plus 1X9 watt , CDL , 3 star rating, heat sink white with polycorbonate diffuser, B-22 base cap, retrofit type, 220/230 volts complete all as specified and directed. 122 S&F LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. 123 S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. 124 S&F building security light LED type 30 W, 6500K, 240V connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. 125 S&F air circulator fans 230 volts single phase 50 Hz 1450 RPM Oscillating 600mm sweep suitable for wall mounting, made of metal body, copper winding including connecting up with three core flexible copper conductor cable for suitable size and wall mounting fastener bolt, nuts & washers etc, complete all as specified and directed. 126 S&F sheet metal enclosure 20Amo SP(2P+E) with metal plug and socket DBs suitable for protection of appliances like AC/Geysers etc complete with one MCB single pole 20 Amps, 240 Volts including connection, testing and making good the disturbed surface complete all as specified and direceted. 127 S&F double door MCB distribution boards sheet steel, powder coated DBs suitable for MCBs fitted with bus bar, neutral link earth bar and din rail single phase and neutral confirms to IS : 13032-1991 of 12 ways complete all as specified and directed. 128 S&F 240V, 10KA B curve miniature circuit breaker (MCB) and current carrying capacity 6 to 32 AMP in the MCB DB complete with connection testing and commissioning complete all as specified and directed. 129 S&F 240V, 10KA C curve miniature circuit breaker (MCB) and current carrying capacity 40 to 63 AMP in the MCB DB complete with connection testing and commissioning complete all as specified and directed. 130 S&F GI bracket mede out from GI pipe 32 mm dia bend to shape as required, 1.2 mtr long fixed on wall with flat iron clamps of size 25X4 mm, 2 Nos with the help of bolts, nuts, washers etc for fixing of security light fitting complete all as specified and directed. 131 Supply, laying and testing XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 Sqmm 2 core complete all as specified and directed. 132 S&F lamp LED heat sink white with polycarbonate diffuser, B-22 base cap, retrofit type, 220/230 Volts,7/9 Watt complete all as specified and directed. 133 S&F LED tube light fittings 1x 20 watt (T-8 ), 4 long, 220 Volts, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. 134 S&F LED building security light fitting 25 Watt,230 Volts, AC outdoor type with high pressure die cast aluminium housing and heat resistant polycarbonate cover complete with driver, lamp & IP 65/66 protection complete all as specified and directed. 135 S&F in repair stepped, electronic fan regulator flush type, 180 Watt, 240 Volts on the existing phenolic laminated sheet complete all as specified and directed. 136 Hanging only ceiling fan (M.D. supply) and connecting up including provision of cable from ceiling rose or connector to fan including Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc and remarking the serial MES fan nos complete all as specified and directed. 137 Taking dowm sub main wiring/ service cable including earth wire and making good disturbed surfaces to match with the existing surfaces of walls, floorscomplete all as specified and directed. 138 M&L for sub main wiring with 2 run of FR PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.0 sqmm alongwith one run of FR PVC insulated & unsheathed multistranded copper conductor of nominal cross sectional area 6.0 sqmm as earth continuity conductor drawn through in & includingPVC complete all as specified and directed. 139 S&F in repair sheet metal enclousers (DBS) when MCBs to be used 8 way, 240 Volt, double door single pole & neutral with 200 Amps rated bus bar complete all as specified and directed. 140 S&F in repair MCB single phase and neutral 40 A,230V 10KA. C curve type complete all as specified and directed. 141 S&F in repairMCB SP 6A-32A, 230V 10kA B curve type complete all as specified and directed. 142 M&L for earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not lessthan 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicatedincluding testing on completion complete all as specified and directed. 143 Supply & installation of Galvanized steel high mast lighting system of 16 meter in two section, 3 mm section thickness, top dia 150 mm, bottom dia 340 mm, with 2/3 wire rope system and its accessories. System is suitable for loading 08 nos 80 to 150w LED lights complete all as specified and directed. 144 M&L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 Sqmm 4 core complete all as specified and directed. 145 Supply and laying GI tubing light grade 40 mm bore dia with all fittings for cable protection complete all as specified and directed. 146 M&L for dry sand cusioningfor UG cable in trenches including spreading levelling and hand panning and consolidating complete all as specified and directed. 147 M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS15658-2006 of 100 mm thickness M-50 grade complete all as specified and directed. 148 Supplying andlayingun-reinforced precast concrete cable cover, Class LV, Type 1,flat, size 250 mm x 150mm x 40mm complete all as specified and directed. 149 M&L for earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire complete all as specified and directed. 150 S&F all in one solar LED street light IP66 with high efficiency mono crystal line solar panel PV module not less than 12V, 20W lithium ferro phosphate battery with in-built BMS technology, capacity 12.8V, 10.5 Ah high efficiency LED 100LM/W, MPPT solar charge controller and aluminium extruded body & is specially programmed to automatically control the dimming and brightness of light, which increase the backup time and minimum 10 Hrs backup including galvanised steel pole of min 20 feet and prepare foundation of size 1x1x4 feet and grouted galvanised steel pole with nut and bolts including all accessories complete all as specified and directed. 151 Supply, laying, connecting and testing 50 mm dia steel tubing, galvanized, medium grade concealed in all type wallwith all fittings, laid in trenches complete all as specified and directed 152 Supply, laying, connecting and testing 25 mm dia steel tubing, galvanized, medium grade concealed in all type wallwith all fittings, laid in trenches complete all as specified and directed 153 S&F 25 mm bore dia gun metal globe valve or gate valve with iron wheel head, screwed both ends with 01 No union for iron pipe heavy duty with ISI marked all as specified and directed. 154 S&F 50 mm bore dia gun metal globe valve or gate valve with iron wheel head, screwed both ends with 01 No union for iron pipe heavy duty with ISI marked complete all as specified and directed. 155 S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Corrigendum Details

Sr No CorrigendumDate Corrignedum CorrigendumType NewSubmissionDate
1 07-10-2024 Bid Auto Extn Corrigendum Bid Auto Extn Corrigendum 14-10-2024

Key Value

Document Fees
INR 500 /-
EMD
INR 94000.0 /-
Tender Value
INR 47 Lakhs /-
Disclaimer :
We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.
Tell us about your Product / Services,
We will Find Tenders for you

Copyright © 2024 · All Rights Reserved. Terms of Usage | Privacy Policy

For Tender Information Services Visit : TenderDetail