Tender For Comprehensive Misc Repair Works In Various Mes Installation Under Area Of Age B/R-Ii At Ge Saugor- 1 Dismantling posts or struts (wood, steel or R.C.C.) any section, including takingout embedded portion in concrete, brick work, masonary, etc and making good disturbed ground complete all as specified and directed by Engineer-in-charge. 2 Site clearance in soft/loose soil complete all as specified and directed. 3 Dismantling of fencing barbed wire/wiremess of any thickness or size and round bar etc complete all as specified and directed by Engineer-in-charge. 4 Excavating in post holes in any type of soil each n.exc 0.5 cum , getting out and removing surplus soil to a distance n.exc 50 m and making good surface complete all as specified and directed by Engineer-in-charge. 5 M& L Cement concrete 1:4:8 Type D 2 (using 40 mm graded aggregate ,in foundations, filling and mass concrete, including demolition of old cement concrete in ground floors and pavings n exc 15cm below or above ground floor complete all as specified and directed by Engineer-in-charge. 6 M&L for PCCtype C-21:3:6 using40mm graded stone aggregate infoundation, filling and mass concrete, including demolition of old cement concrete in ground floors and pavings n exc 15cm below or above ground floor complete all as specified and directed by Engineer-in-charge. 7 M&L for PCCin embedding of chain link fencing, rounded or chamfered on edges type B1 (1:2:4) using 20 mm graded aggregate including necessary formwork, including demolition of old cement concrete in ground floors and pavings n exc 15cm below or above ground floor complete all as specified and directed by Engineer-in-charge. 8 M & L for mild steel Angle ironas in posts and struts in fencing includingcutting tops to shape as directed, drilling holes, notching for wire , etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling bolting or riveting, etc, and similar work and similar conforming to Fe-290 Gde E-165 complete all as specified and directed by Engineer-in-charge. 9 M & L for Mild steel Round bars 10mm dia and over, cut to length, bent to shape required, includinig cranking, bending spirally for hooping of columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9 mm dia or securing with clips quality confirming to Fe-410 W complete all as specified and directed by Engineer-in-charge. 10 S&F chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed by Engineer-in-charge.Note: Weight of chain link fencing will be ascertain by BOO. 11 S&F framed work such as grills gratings,sunshed cover fixed with nut bolts incl,cutting drilling holesetc., with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed baluster, walk ways, railings, framedwork or water tanks and similar work conforming to Fe 290gde E 165, including dismantling of old MS work complete all as specified and directed by Engineer-in-charge. 12 M & L for painting steel surfaces exc 10 cm in width or girth with two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified and directed by Engineer-in-charge. 13 M & L for Preparation of newly steel and iron surfaces of any description n.exc 10cm in width or girth when connected with other painting, applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-charge. 14 M&L for75 mm thick PCC 1:3:6, C2 (40mm graded aggregate) as in plinth Protection finishing cement concrete surface even & smooth without using extra cement complete incl forming construction joint 10mm x 20mm filled with bitumen and coarse sand mortar, including demolition of old cement concrete in ground floors and pavings n exc 15cm below or above ground floor complete all as specified and directed. 15 M&L for providing cement concrete1:2:4 type B-0 (12.5 mm graged aggregate)in window or door cills, lintels, bressumers, steps, quoin, blocks, cover slabs ,coping , bands,shelves, including demolition of existing cement concrete in any position completeall as specified and directed. 16 Dismantling unframed timber scantlings 40 sq. cm & over in section, in any position. 17 S&F Pre painted galvalum sheet 0.50 mm thick havingaluminum zinc coating 150 gsm/ sqm(AZ- 150) corrugated steel sheetany colour having tensile strength of 550 Mpa as in Roof covering /cladding to wall fixed with self tapping screws, including dismantling old plain or corrugated asbestos sheeting , any gauge, thickness complete all as specified and directed. 18 S&F 0.45 mm thickgalvalume sheetprecoated coloured ridge suitable for profile pattern sheetfixed with self driving screws, including dismantling old plain or corrugated asbestos sheeting , any gauge, thickness complete all as specified and directed. 19 S&F structural steel work as in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed. 20 S&F MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment (Fe 290 Gde E 165) complete all as specified and directed. 21 S&F Mild steel screw bolts (machine made) with hexagonal / square heads at one end & screwed the other/ screwed both ends, each screwed end to be fitted with washers & one hexagonal or square nut, length of bolt exc 5cm but n exc 10cm long dia of shank 16 to 20 mm complete all as specified and directed. 22 M&L forbrick work with sub class Bold size bricks straight or curved on plan exc 6 m mean radius built in CM 1:6, including demolition of brick masonry, built in cement mortar with all quoins, arches, pillars, etc and removing of rubbish off the premises complete all as specified and directed. 23 M & L for stone walling of random rubble, uncoursed well bonded, bedded and solidly hearted built in Cement -mortor 1 : 6, including demolition of old brick or stone masonry, built in cement mortar incl all quoins, arches, pillars, etc and removing of rubbish off the premises complete all as specified and directed by Engineer-in-charge. 24 Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. 25 M&L rendering 15 mm thick on surface other than fair face of brick work or stone surfaces with CM 1:6 finished even & fair complete all as specified and as directed 26 M&L Rendering 15mm thick on stone masonry surfaces or surface other than fair face of brickwork in CM (1:4) and 5 mm thick in second coat with and including water proofing compound @ 2% by wt of cement complete all as specified. 27 M&L Rendering 10mm thick on fair faces of brick work or concrete surfaces in CM (1:3) in ceiling complete all as specified and directed. 28 M&L for preparing the new plastered surfaces and applying three coats of white wash on walls all as specified and direcrted. 29 M&L for Three coat of white wash on old decorated surface of walls including preparation of old surface i.ebrooming down with steel wire brushes scraping downmoulds moss and efflorescent salts and treating oil and greasy spots, removing of nails, making good holes , craks etc and washing floors, cleaning glass , joinery , electric fitting, etcall as specified and directed. 30 M&L for preparation of old ceiling surfaces and applying two coats ofWhite wash on ceilingsurfaces complete all as specified and directed. 31 M&L for applying three coats of white wash on new Ceiling surface including preparation of surface complete all as specified and directed. 32 M & L for applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm / litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43litre / 10 sqm including priming coat of exterior primer applied @ 0.90 litre / 10 sqm over new surfaces., including preparation and complete removal of existing treatment of surfaces of old surfaces etc complete all as specified and directed. 33 M & L for complete removal of existing treatment and applying two coats of acrylic emulsion paint , white or tinted over a coat of wall primer and applyingbirla / J. K. wall care whiteputty 1 mm thick in two layerfor levelling the surfaces of oldwalls etc complete all as specified and directed. 34 M&L Two coats of synthetic enamal paint over a coat of red oxide primer on steel surfaces over 10cm width or girth incl preparation of old painted surfaces complete all as specified and directed. 35 M&L for preparation of old wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed. 36 M&L for coloured designer tiles exterior grade ( ENDURA OR Equivalent as given in Appendix C) 10 mm thick, over and including 15 mm thick cement mortor 1:6 set and jointed in floor and pointed in neat cement slurry with grey cement and pigment in floor etc, including dismantling of existing floor tiling and removing rubbish from site complete all as specified and directed. 37 M&L for coloured designer tiles exterior grade ( ENDURA OR Equivalent as given in Appendix C) 10 mm thick, over and including 10 mm thick cement mortor 1:4 set and jointed in verticle surface and pointed in neat cement slurry with grey cement and pigment in verticle surface etc, including dismantling of existing floor tiling and removing rubbish from site complete all as specified and directed. 38 M&Lfor glazed ceramic joint free coloured tiles on vetical surfaces size 600x300x7mm thick, over & including 15mm thick renderingin CM 1:4 set and jointed in neat cement slurry and pointed in white/coloured cement to match the shade /colour of tiles,including dismantling offloor tiling including cement mortar beddingand removing of rubbish off the premises complete all as specified and directed. 39 M&L for machine pressed precast cement concrete coloured chemically treated interlocking paver block any shape and size conforming to IS-15658-2006 of 60 mm thickness M-35 grade with grey cement and pigmentlaidover and including avg 40 mm thick uniformly levelled surface ofstone dust cushioning including PCC 1:2:4 type B-0 as in coping all around of size 150 x100 mm thick, including dismantling of existing tile with bed complete all as specified and directed. 40 Material and labour for providingreinforced cement concrete (nominal mix) Type B -1,1:2:4 (20 mm graded stone aggregate) for foundation including rafts, footings, foundation beams, plinth beams and bases for columns, including demolition of existing RCC complete all as specified and as directed. 41 Material and labour for providingreinforced cement concrete (nominal mix) Type B -1,1:2:4 (20 mm graded stone aggregate)as in columns, pillars, piers, post and struts, including demolition of existing RCC complete all as specified and as directed. 42 M & L for form work to sides & soffits of plinth beam and sides of footings getting rough finished surfaces of concrete complete all as specified and directed. 43 M &L for form work to sides of columns getting rough finished surfaces of concrete complete all as specified and directed. 44 M&L for 10mm dia and over TMT bars cut to length, bent to shape required includingcranking bending spirally for hooping for columns hooking ends and binding with and including mild steelwire (annealed) not less than 0.9mm dia or securing with clips completeall as specified and directed. 45 M&L for 5 mm dia and over upto and including 10 mm dia TMT bars cut to length, bent to shape required includingcranking bending spirally for stirrups, spacers, and binbers and binding with and including mild steelwire (annealed) not less than 0.9mm dia or securing with clips completeall as specified and directed.. 46 S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, including hacking out old broken glass (any thickness, size, quality or description) from wooden / steel frames glazed with oil putty or fixed with beadscomplete all as specified and directed. 47 S&F galvanised mild steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples, including taking out old wire cloth complete all as specified and directed. 48 Taking down chowkats or frames with shutters (w/o taking of shutters from the frame) nexc 1.5 Sqm each complete all as specified and directed. 49 Taking down chowkats or frames with shutters (w/o taking of shutters from the frame) exc 1.5 but n exc n.exc 4Sqm each complete all as specified and directed. 50 Cutting holes in brick walls in cement mortar or cement lime mortar and stone wall built in lime mortarfor inserting holdfasts in exc. One brick but not exc. two brick walland making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 TypeB-1 as required complete all as specified and directed. 51 S& F glazed (5.0 mm thick plain /coloured glass)aluminum door powder coated consisting of frame of 63.50 mm x 38.10 x 1.95 mm size with shutter fixed on frame both side open able on pivotal arrangement with including necessary cutting holes in wall & floor, Door shutter consists of top and bottom rail size is 83 x 44.45x 2mm mm , &lock rail size is 100 x 44.45x 2mm mm & style of door shutter is 85mmx 44.45 x 2mm mmwith handles 2 Nos in each door , hinges has fitted on frame as requiredfixed with rubber gasket & aluminum beading any No of panels with aluminum handle ,locking arrangemen,floor door stopperincl. necessary joining cleats , glazing clips and floor springsetc complete, confirming to IS. 52 S&F aluminium windowssliding type three track powder coated consisting of frame bottom with gutter of sizemin 92.34 X 39 mm,sideand top of size min 92.34X29.70, shutters vertical 39X20 mm,shutter top &bottom of size min 20X39 mm ,shutter interlock min size 39X20 mm with rollers and conceled locking arrangements with 4 mm thick tintedglass with rubber gasket,brush and aluminium beading , ,aluminium grill with fixing arrangement (wt. of grill not less then 2.50 kg/sqm),aluminium wire mess 0.36 mm dia and aperture size 1.40 mmetcincluding necessarycutting holes on wall and floor and confirming to IS complete all as directed by Engr-in- Charge (Al. section thickness 1.50 mm } 53 S&F Mild steel door shutter with MS angle iron shutters frame 35 mm X 35 mm X 5 mm in two panel covered with 1.25 mm thick MS plain black sheet welded to shutter with 2 Nos sliding door bolt of 16 mm dia300 mm long with locking arrangement, 2 Nos of tower bolt of200 mm longincluding MS angle iron frame 40mm x40mmx 5mm as in chowkhat with 6 Nos hold fast of flat iron 30mm X5 mm ,200 mm long with bottom flat iron of size 30mmx5mm and 100 mm size4 Nosbutt hinges including necessary cutting, welding, binding as required with two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces complete all as specifiedand as directed.[Single shutters of approx width0.8 to 1.2 m andht 1.9 to 2.10 M.] 54 Cutting chases, pinning in, in brick wall making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring etc. and making good, in cement mortor 1:3 cutting not exceeding 10cm girth complete all as specified and directed. 55 M & L forPCC ( 1: 2: 4) type B-0 using (12.5mm graded stone aggregate) etcon roof top as a leveling course / paddingto maintainthe slope,finished the surfaces even and smooth without using extra cement, including demolition of existing PCC etc complete all as specified and directed. 56 Taking downof oldroof treatment of any description including demolition of mud phushka, lime, concrete,tiles , cement plaster, padding upto 30cm depth from roof surfaces etc including cleaning, brushing and watering to joints and grooves and throwing the same to a distance exc 250 mtr and n exc 500 mtr from the roof of height 3 to 9 mheight etc and applying new water proofing roof treatment toRCC roof with approved modified membrane of weighing not less than 3kg/sqmcomprising with following items with and including materials and labour as under:-(i) The surface of roof,parpet and gutters drain mouths etc over which water proofing treatment is to be applied shall be cleaned of all foreign matter such as fungus,mass dust etc by wire brushing and dusting.For cast iron drain outlets a groove shall be cut as specified and directed. A fillet of PCC (1:2:4) of 100x100mm shall be provided at all junctions of vertical and horizontal surfaces and wherever there is a change of dirction. The membrane should not be taken over at any steep turns and hence all corners/timers should be rounded.(ii) M&L rendering 10mm thick in cement mortar 1:4 mixed with and including water proofing compound @ 200ml per 50 kg bag of cement applied over roof slab.(iii) Oil based Bitumenprimer conforming to IS-3384-1986 @ 0.3 kgs per sqm to be applied on prepared surface till the surface is properly impregnated.(iv) Applyingone coat of hot blown grade bitumen 85/25 grade @ 1.20 kg/Sqm(v) Laying of water proofing teratment of weight not less than 3 Kg / sqmAPP modified polymeric water proofing membrane composed of 100 micron (+10% ) high density polyethylene sheet ( HMHDPE) as center core, which is standwiched between high quality polymeric bitumen mix having softening , high heat resistance and cold flexible protected on either side with a thin thermo fusible HMHDPE film with side and laps 75 mm and 100 mm as per manufacture instruction etc.(vi) Applyingone coat of hot blown grade bitumen 85/25 grade @ 1.20 kg/Sqmover the membrane. (vii) Applying aluminium paint in two coat @ 100 gm/sqm in each coat on finished membrane surfaces complete all as specified and directed.
