|
| 1 | Earthwork: Excavation in trenches for foundations,pipes cables etc. in ordinary soil (Loam, Clay or Sand) including lift upto 1.5 m lead upto 50m and drassing of sides and ramming of bottom disposal of surplus excavated earth as directed by Engineer- in- charge with lead of 50 m. (PWD SI No-251)/2022 |
| 2 | Providing and laying in cement concrete in 8:4:1 ( stone ballast 8 (40 mm nominal size) : 4 approved coarse sand : 1 cement and curing complete, including cost of formwork in foundation. (PWD S.I No- 281) |
| 3 | RCC work with cement approved coarse sand and 2cm (3/4\")gauge approved stone ballast in the proportion 1:1½:3 (1 cement : 4½ aggregates)slab including necessary centering & shuttering excluding supply of reinforcement and its bending the same with 24 BWG GI binding wire and necessary centering & shuttering excluding supply of reinforcement and complete 284/2022 |
| 4 | R.C.C. work with cement approved coarse sand & 2cms(3/4\") gauge stone grit in proportion of 1:1.5:3 in coloumns and walls excluding supply of reinforcement and its bending but including its fixing & binding the same with 24BWGGI Binding wire & including necessary centering & shuttering etc. & and also including supply of all material labour T&P etc. required for proper completion of work. Binding wire is to be supplied by the contractor free of cost. ( S.I NO. 289 CH-5)/2022 |
| 5 | Mild steel (Tor steel or plain) or iron in plain work such as reinforced concrete or reinforced brick work (when not included in an overall rates) wrought to required shape asnecessary including bending for proper completion of the work and including supply of steel its wastage bend hooks andauthorised overlapping shall be measured up to foor two level . (PWD S.I No- 504) |
| 6 | M-150 brick work in 1:4 (one cement and four coarse sand of 2.25 F.M. mortar) in foundation and including supply of all material and T &P etc. required for proper completion of work. (S.1. 307A)/2022 |
| 7 | 12 mm thick plaster with (1:4) One part of cement and Four part of approved Corse sand includig supply of all material and completion of work.S.I No. 584/2022 |
| 8 | Providing & Installing of Floor Mounted M 20 chlorinator 5 kg/ Hour the complete system consist of Tonner, Gas piping, Water booster pump set, Electric Panel/Cables, Water Side piping, Solution side piping, Chlorine gas detector, Safety equipment, Material Handling equipment, Mandatory spares, Leak Gas absorption Equipment. completed in all respect for proper functioning of the system as per requirement at site. (Make:- Metito, Pennwalt, M.U.) |
| 9 | For Water Analyzer:Measurement Parameters: pH, COD, BOD & TSSOnline Water Analyzer for measurement of pH, COD, BOD & TSSModel: UV300Make:Horiba Advanced Techno France SAS(Formerly Tethys Instruments SAS, FranceSpecifications:COD, BOD & TSS measurement by UV light absorption methodpH measurement by Electrochemical method- Input: 01 No. 4-20mA input module to connect signal cable from 01 No.flowmeterPower Supply: 90-264 VAC 50/60 Hz 40 VAScreen: Colour TFT LCD, Size: 5.7\", resolution: 320 X 240 pixels, LEDbacklight, Resistive touch screenCommunication: RS232 MODBUS protocol & USBEnclosure: Stainless steel with epoxy coating, IP65- Measurement Range:COD: 0 - 500 ppm (Other higher ranges available upon request)\"TSS: 0 - 500 ppm BOD: 0 - 200 ppm (Other higher ranges available upon request) completed in all respect for proper functioning of the system as per requirement at site \"TSS: 0 - 500 ppm BOD: 0 - 200 ppm (Other higher ranges available upon request) completed in all respect for proper functioning of the system as per requirement at site |
| 10 | flow meterProviding, fixing, testing and commissioning of Prosonic FMU40 sensor is suited for non-contact level measurement in fluids, pastes, coarse bulk material and flow measurement in open channels or at weirs. The two-wire or four-wire compact transmitter can be used in applications with storage tanks, agitators, on stockpiles and conveyor belts. The envelope curve can be shown on the on-site display for simple diagnosis. Linearization function (up to 32 points) for conversion of the measured value into any unit of length, volume or flow ratea.Process connection: Thread b.Temperature: -40 to +80°C (-40 to +176°F) c.Pressure: +0.7 to +3bar (+10 to +44psi) d.Maximum measuring distance: Liquids 5m (16ft), Solids 2m (16ft) e.Blocking distance: Liquids and Solids 0.25m (0.8ft) completed in all respect for proper functioning of the system as per requirement at your of site |
