Tender For Provision Of Office And Adm Accommodation At Panzgam Grnunder Aor Of Ge 874 Ews.; 1 Surface excavation not exceeding 30cm deep and averaging 15 cm deep and getting out in any type of soil, complete all as specified and directed. 2 Excavation in trenches n exc 1.5m wide and n exc 1.5m in depth for foundation etc n exc 10 sqm on plan and getting out in any type of soil complete all as specified and directed. 3 All as per item No 2 above but depth exc 1.5m and n exc 3 m. 4 Returning filling in including spreading levelling watering and well ramming in layers n exc 25cm complete all as specified and directed. 5 Removal of excavated materials n. exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed. 6 Spreading and levelling earth in layers n exc. 25cm thick, well ramming including watering as required complete all as specified and directed. Note:- Earth Removed under respective item of BOQ shall be used. 7 M&L for plain cement concrete (1:4:8), type D-2, using40mm graded stone aggregate as in sub base filling and mass concrete complete all as specified and directed. 8 M&L for brick work with sub class B brick straight or curved on plan exc 6m mean radius built in cement mortar 1:6. complete all as specified and directed. 9 M&L for brick work with sub class B brick straight or curved on plan exc 6m mean radius built in half brick thick wall of cement mortar 1:4 complete all as specified and directed. 10 M & L for stone walling of random rubble, brought upto courses well bonded, bedded and solidly hearted built in CM 1:4 complete all as specified and directed. 11 Extra over stone walling for hammer dressing to face stone and dressing of face beds and joints complete all as specified and directed. 12 M & L for flush pointing to random rubble stone masonry in cm 1:4, uncoursed or brought up to courses complete all as specified and directed. 13 M&L for RCC Design Mix M-30 as in Foundations, including rafts, footings,foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. 14 M&L for RCC Design Mix M-30 as in Columns, pillars, piers, posts and struts complete all as specified and directed. 15 M&L for RCC Design Mix M-30 as in Beams, cantilevers, bressummers,lintels over 1.5m span complete all as specified and directed. 16 M&L for use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed. 17 M&L for use and waste of formwork to sides of pillars, posts struts piers columns of square or rectangular and stanchions complete all as specified and directed. 18 M&L for use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummer lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed. 19 Supply and fixing 10 mm dia and over mild steel TMT bars, cut to length, bent to shape required cranking bending and binding with and including mild steel wire annealed not less than 0.90 mm dia. complete all as specified and directed. 20 All as per item No 19, but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed. 21 S&F mild steel work as in rooftrusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc confirming to Fe410-W (Grade E-250) quality A complete all as specified and directed. 22 S&F mild steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade Fe410-W (Grade E-250) quality A complete all as specified and directed. 23 S&F mild steel work as in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe410-W (Grade E-250) quality A complete all as specified and directed. 24 M&L for mild steel work as in screw bolts (machine made),16-20 mm dia, with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 15cm and n exc 22.5cm long complete all as specified and directed. 25 S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with tapping screws complete all as specified and directed. 26 S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with tapping screws complete all as specified and directed. 27 M& L for E-board ceiling 6mm thick precoated non asbestos E board classic designer tiles of size 605x605mm fixed in GI snap grid interlocking system powder coated at bottom of same manufactures including GI wire as per manufacturer specifications. if pre coating is spoiled by worker while fixing of tiles the complete tile surface shall be provided with 2 coats of plastic emulsion paint complete all as specified and directed. 28 M&L for 6 mm thick Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on one face; fixed with screws to timber frame work in ceiling complete all as specified and directed. 29 S&F plain fillets rectangular or triangular in section clean sawn secured with nails or brads exceeding 3 sqcm & n exc 6 sqcm, second class soft wood (Kail) clean sawn complete all as specified and directed. 30 M&L for second class softwood as in scantling, clean sawn fixed in position with nails, unframed work, complete, all as specified and directed. 31 M&L hardcore (broken stone or boulders) of gauge n exc 63 mm deposited spread and levelled in layers n exc 15 cm thick watered and rolled / rammed to a true surface all complete all as specified and directed. 32 M&L for 75 mm thick Subbase PCC (1:3:6)type C-2 (using 40 mm graded stone aggregate) complete all as specified and directed. 33 M&L for providing, cement concrete type B-0 (1:2:4) (using 12.5mm graded crushed stone aggregate)in roof kerbs or mud stops, rounded or chamfered on edgesin lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed. 34 M&L for coloured non-skid ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.18 sqm but n. exc 0.38 sqm, laid in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed. 35 M&L for coloured non-skid ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.06 sqm but n. exc 0.11 sqm, laid in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed. 36 S&F for glazed ceramic tiles coloured of size 350x250x7mm thick/450x350x7mm thick fixed in vertical surfaces, set and jointed in neat cement slurry and pointed in white and colour cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and directed. 37 M&L for 25mm thick PCC (1:2:4) type B-0 using 12.5mm graded stone aggregate as in floor finished even and rough to receive the topping layer complete all as specified and directed. 38 M&L for 75 mm thick, PCC (1:3:6), type C-2 (using 40 mm graded stone aggregate) as in paving, plinth protection etc, surfaces finished even and smooth without using extra cement and divided into panels not exc 1.20 Mtr complete all as specified and directed. 39 M& L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick / concrete/stone, surfaces and finished even and smooth without using extra cement mixed with WPC @ 3% by Wt. of cement (External surfaces) complete all as specified and directed. Note:- WPC shall be measured and paid separately. 40 Supply only approved integral water proofing compound complete all as specified and directed. 41 M&L for rendering 15mm thick on other than fair faces of brick/stone or concrete surfaces in CM 1:6, finished even and smooth without using extra cement (internal surfaces) complete all as specified and directed. 42 M&L for preparation of newly plastered surface of walls and applying two coats of oil bound distemper over and including 2mm thick wall care putty to achieve smooth surface complete all as specified and directed. 43 M&L for preparation of newly plastered surface of walls and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces. complete all as specified and directed. 44 M & L for preparing new plastered surfaces of walls and applying two coats of cement base paint over one coat of white wash complete all as specified and directed. 45 M&L for preparing newly steel surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer exc 10cm width or girth complete all as specified and directed. 46 S&F pressed steel frames for doors of size 125mmx60mmx1.25mm with one or more rebates including necessary fixing lugs, hinges, lock, strike plate, etc., complete with flat iron hold fasts and necessary concrete to fix hold fasts complete all as specified and directed. Note:- Cost of filling of PCC 1:2:4 type B-0 filling in hollow portion of frame shall be included the quoted rates. 47 S&F 35mm thick, 2nd class hard wood, plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed. 48 S&F 35mm thick, 2nd class hard wood, Glazed and skeleton shutter, open rebated and prepared to receive glass, gauge etc. (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc. complete all as specified and directed. 49 M&L for natural colour 15 micron anodized aluminium sliding window three track with chowkhat and aluminium grill of approved design complete all as directed with all fixing arrangements (including providing and fixing window handles, tower bolts and provision for fixing lock) including neoprene lining. The member shall made out of extruded aluminium sections comprising of:- (a)Shutter vertical member 47.62 x 45.45 x 1.74mm weighing 0.881 Kg/RM.(b)Shutter top member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM. (c)Shutter bottom member 47.62 x 44.45 x 1.14mm weighing 0.607 Kg/RM. (d) Natural colour 15 micron anodized aluminium anodised frame of chowkhat of section 85.00 x 44.45 x 1.80 mm weighing 1.302 Kg/ RM, with flat iron hold fasts and necessary concrete to fix hold fasts all as directed. (e)including 5.50mm thick tinted glass fixed with alumnium beading, silicon lining and gaskets and stainless-steel wire cloth complete. (f) The size of anodised aluminium round handle, fancy type shall be 100mm dia (02 Nos) and anodised aluminium tower bolt of size 100mm (02 Nos). 50 S&F 3mm thick figured glass, pin head type and glazing with oil putty in squares in exc 0.5 sqm in each pane complete all as specified and directed. 51 M&L for galvanised mild steel wire cloth 0.56 nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples, fixed in repairs, complete all as specified and directed. 52 S&F mild steel work in any other section as in window guard bars, grill and other similar work such as in hold fast for chowkat complete all specified and directed. 53 S&F for 100mm long stainless-steel butt hinges medium weight cold rolled complete all as specified and directed. 54 M&L for Aluminium handles cast type anodised 150 mm long complete all as specified and directed. 55 M&L 250mm long Aluminium alloy, anodised, sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, 56 S&F for 200mm length aluminum, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed. 57 M&L for precoated sheet type door spring, heavy type, 200 mm long including roller and roller plate complete all as specified and directed. 58 S&F 2nd class hard wood small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary labours; articles n exc 200 cu. cm each complete all as specified and directed. 59 M&L for preparing newly wooden surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed. 60 S&F for 75mm long stainless-steel butt hinges medium weight cold rolled complete all as specified and directed. 61 M&L for Aluminium handles cast type anodised 100mm long complete all as specified and directed. 62 S&F for 150mm length aluminum, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed. 63 S&F Harrison rails, stainless steel, with fixing brackets, stops, rollers etc., complete all as specified and directed. 64 S & F solid PVC door frame of size 50 x 47mm made out of 5mm plain coloured PVC sheet reinforced with MS square tube, in opening complete all as specified and directed. 65 M&L for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’channel having a PVC sheet strip of 20mm width stuck inside withsolvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing, complete all as specified and directed. 66 S & F for factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side pre lam PVC sheet and edges shall be painted to match with pre lam sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 160 of MES SSR 2010 Part-II complete all as specified and directed. 67 S & F for factory made fully glazed PVC window/ventilator shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; complete all as specified and directed.Note: - Glass shall be measured and paid separately. 68 S&F steel water tubing medium grade galvanized with all fittings and fixed complete to walls, ceilings or laid on floors, 20 mm dia bore of tube complete all as specified and directed. 69 S&F GI steel water tubing medium grade galvanized with all fittings and fixed complete to walls, ceilings or laid on floors, 15 mm dia bore of tube complete all as specified and directed. 70 M&L for lagging to pipes 15mm dia used in internal water supply or plumping all round with,25mm thick bonded mineral wool preformed SNAP ON pipe sections of density 144 kg/cum conforming to IS-9842 complete all as specified and directed. 71 M&L for lagging to pipes 20mm dia used in internal water supply or plumping all round with,25mm thick bonded mineral wool preformed SNAP ON pipe sections of density 144 kg/cum conforming to IS-9842 complete all as specified and directed. 72 S&F Vitreous China wash down water closet pan with P trap (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) Pedestal pan and trap, including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe, etc. complete all as specified and directed. 73 S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25-metre-long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect complete all as specified and directed. 74 S&F toilet paper holder with flap recessed type (stainless steel) of vitreous china fixed to walls with chromium plated (CP) brass screws complete all as specified and directed. 75 S & F for 10 ltr capacity PVC valveless syphonic action type flushing cistern, low level white with inlet ball valve float and handle including brackets complete all as specified and directed. 76 S&F Vitreous China urinals, half stall type, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinalback in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed. 77 S & F for vitreous china wash basin white flat back size 450x300mm including brackets, cutting for and pinning in ends or brackets with waste coupling of PTMT bore of 32 mm dia discharge pipe (half or full threaded) minimum wt 32 mm (45 gms/40-60 gms) complete all as specified and directed. 78 S&F pillar taps cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lettered Hot or cold with long screwed shanks and fly nuts, screwed for union pipe and fixed to 15mm dia pipe complete all as specified and directed. 79 S&F tubular towel rail brass chromium plated, 20mm dia, D type 60 cm long between flanges complete all as specified and directed. 80 S&F 600x450mm bevelled edge mirror of selected quality glass, moulded on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated screws and cup washers complete all as specified and directed. 81 S&F CP soap dish complete all as specified and directed. 82 S&F Sheet glass shelf assembly consisting of 5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed. 83 S&F 15mm bore dia of stop valves but fancy type, chromium plated with long shank and cup (concealed type) screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed. 84 S&F 15mm bore dia of angle valves cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed. 85 S&F bib taps 15mm bore, fancy type chromium plated with butterfly handle, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed. 86 M & L for PVC (SWR) 110mm bore (dia) soil, waste and ventilating pipe, singe socketed, in any length with Rubber Ring Joints fixed to walls etc, complete all as specified and directed. 87 M & L for PVC (SWR) 110mm bore (dia) PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors etc, complete all as specified and directed. 88 M & L for PVC (SWR) 75mm bore (dia) soil, waste and ventilating pipe, singe socketed, in any length with Rubber Ring Joints fixed to walls,etc, complete all as specified and directed. 89 M & L for PVC (SWR) 110mm bore (dia), Bends any type with Access Door, etc. and Jointing with Solvent Cement, complete all as specified and directed. 90 M & L for PVC (SWR) 75mm bore (dia), Bends any type, and Jointing with Solvent Cement, complete all as specified and directed. 91 S&F PVC gully trap square or round mouthed type (P), size of trap 125x 110mm and jointing to drains with solvent cement complete all as specified. 92 S&F PVC connection 15mm dia and 600mm long with PTMT nuts and washer complete all as specified and directed. 93 S&F waste coupling of PTMT (half or full thread). (Minimum weight 32 mm-45 gms / 40mm-60gms) for 32mm bore dia of discharge pipe fixed to WHB, sink complete all as specified and directed. 94 Supply only HDPE pipes of pressure rating 6kgf/sqcm of 32mm bore for outlet pipe of WHB complete all as specified and directed. 95 M & L for PVC (SWR) 110mm bore (dia), Single T Junction equal or unequal with Access Door, etc. and Jointing with Solvent Cement, complete all as specified and directed. 96 M & L for PVC (SWR) 75mm bore (dia), Single T Junction equal or unequal with Access Door, etc. and Jointing with Solvent Cement, complete all as specified and as directed. 97 S&F110mm dia PVC (SWR) vent cowl complete all as specified and directed. 98 S&F110mm dia PVC (SWR) P’ trap complete all as specified and directed. 99 S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed. 100 S&F CP grating 125mm complete all as specified and directed. 101 S&F rotational moulded polyethylene water storage tank(cylindrical vertical with closed top) hoisted and fixed in position of 1000 liters capacity confirming to IS specificationcomplete all as specified and directed. 102 S&F 20 mm dia ball valves, high pressure of epoxy coated aluminium rod and high-density plastic ball complete screwed for iron pipes or brass ferrule and fixed complete all as specified and directed. 103 M & L for Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors in with grey pigment cement and pigments over 20mm screed bed in CM 1:4 complete all as specified and directed 104 M & L for 100mm thick Plain cement concrete M-7.5 nominal mix, type D-2, using 40mm graded mechanically crushed stone aggregate as sub base to floor, surfaces finished even and fair complete all as specified and directed. 105 M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extras and complete all as specified and directed. 106 M&L for construction of 10 users septic tank complete all as specified and shown on drawing No. CESZ-TD-/2015 sheet No 1/3 & 2/3 dated 22 Feb 2015 (Revised dt 21 Mar 2015) and specified in particular specifications. 107 M&L for construction of Soakage well, of size 1.8 m dia at bottom and 3 m total depth complete all as specified and shown on drawing No. CESZ-TD-/2015 sheet No 1/3 & 3/3 dated 22 Feb 2015 (Revised dt 21 Mar 2015) and specified in particular specifications. 108 M&L for 150 mm thick reinforced concrete pipes, class NP2 laid and jointed complete with collars complete all as specified and directed. 109 M&L for PCC M 7.5 (Nominal mix) type D-2, using 40mm graded stone aggregate as in bed of drain pipe 150mm dia (nominal) including packing under and hanuching against the sides of pipe after they are laid and tasted complete all as specified. 110 M&L for precast RCC 1:2:4 type B1 cover slab using 20mm graded stone aggregate with plain fair faces incl. chamfers, weathering and setting in CM 1:6 including necessary form work complete all as specified and directed. 111 M&L for brick work sub class Bbrick straight or curved on plan exceeding 6m mean radius built in CM 1:4 compete all as specified and directed. 112 M & L PCC 1:3:6, nominal mix type C-2 using 40mm graded crushed stone aggregate as in foundation filling and mass concrete complete all as specified and directed. 113 M&L for 15mm thick rendering cement plaster in CM 1:4 on other than fair faces of brick masonry surface finished even and smooth without using extra cement complete all as specified and directed. 114 M&L for point wiring with 1.5 Sq mm multi stranded insulated copper conductor single core PVC insulated cable 1100 volt including casing and caping for one light point controlled by one switch including sunken box with gang box/outer plate including PVC insulated 1.5 Sqmm copper conductor FRLSH as earth wire for one light controlled by one switch completed all as specified and directed. 115 All as per description of serial item No 114 here -in -before but for 3-pin socket out let 5 Amps on independent board with other switches with continuous PVC insulated copper conductor cable 1.5 Sqmm FRLSH earth wire. 116 All as per description of serial item No 114 here -in -before but for 3-pin socket out let 15 Amps on independent board with 2.5 Sqmm FRLSH multi stranded. copper conductor PVC insulated cable 1100 volts grade with continuous continous1.5 Sqmm FRLSH earth wire. 117 Supply and fixing lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings suitable for LED bulb 7 watt completed all as specified and directed. 118 Supply and fixing LED 7-Watt Bulb with B22 pin, suitable for fixing in holder completed all as specified and directed. 119 S&F decorative LED batten for surface and pendant applications.Anodized extruded aluminium housing, high transmissivity diffuser, high lumen output of VIVA MINI LED Luminaires (4FT) of 20W connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and directed. 120 Supply and fixing LED luminaire 600mm x 600mm 35/36-watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holder and LED lamp suitable for roof ceiling including connecting up the driver three core flexible copper conductor cases of suitable size completed all as specified and directed. 121 S&F of LED light fitting, 1x9 W bulk head luminaries, with lamp holders, etc. complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V, 50 HZ completed all as specified and directed. 122 S&F of modular type switch piano 6 Amps single pole one way completed all as specified and directed. 123 S&F of ceiling rose surface Bakelite 65x50mm two to three terminals (ISI Marked) completed all as specified and directed. 124 S&F switch socket combination 2-in-1, 5 pin 6 Amps modular type (ISI Marked) complete all as specified and as directed. 125 S&F Switch socket combination 5 in 1, 5 Pin 15 Amp modular type complete all as specified and as directed. 126 S&F rectangular boards/ blocks of size 30x25x4cm depth closed recessed, complete all as specified and directed. 127 S&F Sheet metal enclosure factory made for DBs single pole and neutral double door 240 volts 8 way with 200 Amps rated bus bar fixed on walls, including dressing and connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning and making good of wall completed all as specified and directed. 128 S&F amp rating 240V, 10KA C curve miniature circuit breaker (MCB) of Single Pole and Neutral (SPN) 32-63 Amp and current carrying capacity in the MCB DB complete with connection testing and commissioning completed all as specified and directed. 129 S&F amp rating 240V, 10KA C curve miniature circuit breaker (MCB) of Single Pole 5 to 32 Amp and current carrying capacity in the MCB DB complete with connection testing and commissioning completed all as specified and directed. 130 S&F of house service bracket (hook type) complete with 3.0m long G.I. pipe 40mm dia medium grade, two Nos 900 bends. M.S. hook and stay or guy complete all as specified and directed. 131 S&F of 1100 volt grade heavy duty cable PVC insulated multistranded aluminum stranded conductor served with PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 mtr apart including 4mm dia GI suspension wire one twin core cable flat of circular of size 16 Sqmm complete all as specified and as directed. 132 M&L for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) connected to galvanized iron wire4mm dia by means of bolts, nuts and washers of galvanized iron or steel, GI light grade protection pipe 15mm dia, GI medium grade water pipe 20mm dia with funnel all as shown in electric plate No 3 of SSR-2009 pt-I and testing complete including earth work in any type of soil PCC 1:2:L4 as in earthing pit CI pit cover 5.5mm thick common salt charcoal completed all as specified and directed. 133 S&F voltage stabilizer for automatic operation, single phase and neutral air-cooled indoor type & designated for input variation between 90V to 290V with output voltage stabilizer at 230 V with accuracy + 2.5% 4-6 Sec initial delay and of capacity 10 KVA complete all as specified and directed. 134 Supply and fix of exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m completed all as specified and directed. 135 S & F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20mm and fixed complete all as specified and directed. 136 S & F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe 25mm and fixed complete all as specified and directed. 137 S&F of GI water tubing 20mm bore medium grade, galvanized, with all fittings like socket, union, elbow, bend, tees etc jointed and laid in trenches complete all as specified and as directed. 138 S&F of GI water tubing 25mm bore medium grade, galvanized, with all fittings like socket, union, elbow, bend, tees etc jointed and laid in trenches complete all as specified and as directed.
