Tender For providing Of Ration Store And Fencing Under Ge Brichgunj Port Blair.- 1 M & L Excavating over areas, n exc 1.5M deep and getting out soft /loose Soil. 2 All as per item no 1.00 here in before butfor each additional 1.5M or part thereof in depth beyond the first 1.5 M and getting out soft/ loose Soil. 3 Excavation in trenches n. exc. 1.5M wide and not exceeding 1.5M in depth, for foundation, etcor for shafts, walls, cesspits, manholes, pier holes, etc getting out in soft/loose soil, complete all as specified and as directed. 4 M&L PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling. 5 M & L for RCC- M - 30 Design Mix as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete all as specified and directed. 6 M&L Reinforced cement concrete (design mix M-30 grade using 20mm graded aggregate) above top of footings including attached pilasters and buttresses. 7 M & L for RCC- M -30 Design Mix as in columns, pillars, piers,posts and struts as specified and directed. 8 M & L for RCC- M -30 Design Mix as in beams, cantilevers,bressummers, lintels over 1.5m span as specified and directed. 9 M & L for RCC- M -30 Design Mix as in slabs supported on walls,beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in,shelves and the likeall as specified and directed. 10 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm 11 Removing excvated soil to a distance n.exc 50 m and depositing as directed 12 Use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for fair finished surfaces. 13 M & L for Use and waste of form work to sides of pillars, posts, struts, piers, columns and stanchions 14 Use and waste of form work to sides and sofit of Beams for Fair finished surfaces. 15 Use and waste of form work to sides and sofit of Slab & Chajja etc for Fair finished surfaces. 16 M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips. 17 M&L Mild steelTMT bars 6 mm to 8mm dia cut to length bent to shaperequiredand binding with mild steel wire annealed not less than 0.9 mm dia. 18 All as per item no 17.00 here in before but 5mm dia and over up to and including 10mm dia as in stirrups, spacers, binders and the like 19 M&L Precast Cement Concrete Block Masonry with Solid Block, exc 10cm in width in type C-1, 1:3:6 (using 20mm graded stone aggregate) set in CM (1:6) all as specified. 20 M&L for 40mm thick Damp proof course in cement concrete 1:2:4 type B-Oto horizontal or vertical surface including necessary formwork 21 M&LRendering 10mm thick on concrete surfacesin CM (1:6) finished even & smooth without using extra cement. 22 M&L Rendering 5mm thick in CM 1:3 on soffits of RCC slabs, roof projections, soffits and sides of RCC beams, waist slab, Loft Slab, RCC shelves, Chajjas, and the like finished even and smooth without using extra cement. 23 M&L 15mm thick rendering in two layers of 10mm thick backing coat in CM 1:6 and 5mm thick floating coat in CM 1:4 mixed with water proofing compound on all external wall surfaces finished even and smooth without using extra cement. (Note : Water proofing compound shall be measured and paid seperately) 24 Supply only integral WPC (3% by wt of cement). 25 M&L preparation of newly plastered surfaces of walland applying two coats of Oil Bound distemper over a coat of primer over a coat of internal wall care putty as specified and directed. 26 All as item no 25.00 here in before but on Ceiling surfaces 27 M& L for Finishing walls with Acrylic smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) etc complete all as specified and as directed by Engineer-in-Charge.(Make Apex Ultima) 28 M&L Spreading and levelling in layers n exc 25 cm thick for filling under floors or in foundations including watering and consolidation 29 Surface excavation n. exc(not exceeding) 30 cm deep and averaging 15 cm deep and getting out in hard/ dense soil. 30 M&L Hard Core of gauge n.exc. 63mm deposited spread and levelled in layers n.exc. 15 cm thick watered and rolled/ rammed to a true surfce. 31 M&L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate in 75mm thick as in sub base. 32 M&L PCC 1:2:4 type B-1 using 20 mm graded stone aggregate in 40mm thick. 33 M&L PCC 1:3:6 type C1 using 20mm graded aggregate of 75 mm thick as in Plinth Protection. 34 M & L Chequered cement concrete tiles, with grey cement and pigment 30cm x 30cm x 20mm thick set, jointed and pointed in neat cement slurrry in floors including 20mm thick screed bed in Cm 1:4 all as specified and directed. 35 M&L Coloured Non-Skid Ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.18 Sqm but not exceeding 0.36 Sqm in floor etc,set and jointed in neat cement sluryy and pointed in coloured cement to match as in floor over 20mm thick screed bed in CM (1:6) all as specified. 36 All as per Item No 35.00 here in before as in Dado/Skirting/Steps etc set and jointed in neat cement slury and pointed in coloured cement to match all as specified and directed including backing coat 10mm thick in CM 1:6 all as specified. 37 Material and labour for Powder coated aluminium sections (minimum Thickness of Powder costing 50 micros) for partitions, window and door with frame and shutters fully or partially glazed, side Hungtype ( two numbers glazed and gauzed) without sash bars, with panel inserts of sheet glass, gauze including necessary jointing cleats, glazing clips, rubber beading, Neoprene packing, anodized aluminium snap beading, screws,i max hinges, butt hinges etc. The size of aluminium sections shall be all as specified in relevant IS code and SSR part-I and completed all as specified and as directed by engineer-in-charge.(Note: (i) supply only panel inserts of glass/gauze, handles, tower bolts and sliding bolt will be measured and paid separately as supply only.(ii) Weight of aluminium section only shall be accounted for payments purpose. However, until rate quoted shall be deemed to include for cost of rubber beading, glazing clips, neoprene packing and fixing only of panel inserts of glass/ particle board/gauze, handles, hinges, sliding bolts, tower boltsetc.) 38 S & F Steel rolling shutters, of 1.25mm thick with ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: but gear operated type with bevel gear box and crank handle 39 Supply only 12 mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination and fixed to aluminium frames complete all as specified and as directed by Engineer -in-Charge. 40 Supply only 4.0mm thick sheet glass, ordinary quality in squares n exc 0.50 sq.m in each pane. 41 S&F 100 Butt hinges extruded aluminium alloy, anodised. With galvanished mild steel hinge pin , anodised and fixed type B-21 42 Supply only Aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) 300 mm long and fixing clips to sheet cast or extruded sections and fixing bolt or cast aluminium alloy complete all as specified. 43 Supply only Aluminium anodised barrel tower bolt of extruded section of size 150mm long complete all as specified. 44 Supply only Aluminium anodised barrel tower bolt of extruded section of size 100mm long complete all as specified. 45 Supply only 100 mm long extruded aluminium alloy anodised handles fabricated type complete all as specified. 46 Supply only 150mm long extruded aluminium alloy anodised handles fabricated type complete all as specified. 47 S&F for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe-410-W grade E 251 Quality B complete all as specified and directed. 48 S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 49 Mild steel bolts of diameter of neck exc 12mm and n.exc 20mm, purpose made with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut n exc 30cm long as specified. 50 Preparation of new or previously untreated steel surfaces & applying a two coats of synthetic enamel paint over a coat of red oxide primer over 10cm in width or girth,not otherwise described. 51 S&F 0.50 mm thick pre painted galvalume aluminium zinc coating GI based corrugated steel sheet of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self taping screws as specified. 52 S&F 0.50 mm thick pre painted galvalume aluminium zinc coating GI based plain steel sheet of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self taping screws as specified. 53 S&F MS works as in wind ties for roof incl securing bolts etc complete all as specified and as directed. 54 S & F for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 55 M&L Painting to new steel and iron surfaces of n exc 10cm wide or girth by two coats of synthetic enamel paints over a coat of red oxide primer including preparation complete all as specified and as directed. 56 Material and labour for false ceiling with aluminium grid work (Size of grid 600x600 mm) with 35 x 25 x 1.5 mm main tee and 25 x 25 x 1.4 mm cross tee and wall angle and suspended with 2mm dia GI wire hooked to roof with needful adjustment bolts at an interval of 1.20 m centre to centre staggered and board with Eco board decorative type size 600 x 600 x 4 mm thick finished with two coats of oil bound distemper over a coat of primer on exposed surfaces all as specified and directed by Engineer-in-Charge. 57 Excavation in post holes (or similar holes) each not exceeding 0.5 cum getting out in soft/ Loose soil returning filling in and ramming earth or broken rubble mixed with earth around in layers n.exc 25cm watering and removing surplus soil to a distance not exceeding 50m and making good surfaces complete all as specified and as directed. 58 M&L for PCC 1:3:6 type C2(using 40mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and as directed. 59 Supply only PVC coated (1mm thick) chain link fencing exc 2.00 but n.exc 3.50 kg per sqm with size of mesh 50 x 50 mm and thickness of wire n.exc 2.83 mm all as specified and as directed. 60 Fixing only PVC coated chain link fencing including fixing of line wires any mesh, size and any type of standards, rails, straining bolts etc including provision of binding wires complete.(Supply of MS line wire and flat iron bolt & nuts measured and paid seperately) all as specified and as directed. 61 Supply only 6mm dia GI wire PVC coated for support/line wire to chain link fencing complete all as specified and as directed. 62 Supply only mild steel angles, bars, flats etc as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 all as specified and as directed. 63 Supply only mild steel bolts with hexagonal or square head one end and screwed the other or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut exc 5 cm longn.exc 10 cm long dia metre of neck exceeding 11 to 15 mm complete all as specified and as directed. 64 S&F Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) 65 M&L for preparation new steel surfaces of any description n.exc 10cm width or girth when unconnected with other painting or when painted in a different tint, and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed. 66 M&L Point wiring complete with 1.5 sqmm single core FRLS PVC insulated andunsheathed cable 1100 volts grade with multistranded copper conductor drawn through and including PVC casing and caping and all accessories fixed to walls / roofs / floors / ceiling etc. and including provision of 1.5 sqmm copper cable green in colour as earth continuity conductor and connected to common earth dolly, including fabricated steel terminal box made out of 1.60mm thick MS sheet concealed in walls, with 3mm thick laminated sheet top cover for housing the switches, socket outlets,fan regulators etc., all as specified and as directed forthe following:-One light point controlled by one switch 67 All as per item no 66.00 here in before but One fan point controlled by one switch and one regulator 68 All as per item no 66.00 here in before but One 3 pin switch socket outlet point 5 amps on independent board 69 All as per item No 1 here-in-before but for 3 pin 15 Amps switch socket combination on independent board with 4 sq mm copper cable and provision of 4 sq mm FRLS PVC insulated stranded copper conductor cable for earth continuity conductor connected to common earth dolly connecting upto fittings complete all as specified and as directed. 70 Supply and fix switch piano flush button single pole oneway 5 amp complete all as specified and as directed. 71 Supply and fix switch socket combination 3 & 2 pin (multi pin) 5 amp flush type complete all as specified and as directed. 72 Supply and fix switch socket outlet multipurpose 3 pin 15 and 5 amp controlled by one switch, flush type complete all as specified and as directed. 73 Supply and fixceiling rose surface baklite 65 x 50 mm 3 terminal, complete all as specfified and as directed by Engineer-in-Charge 74 Supply and fixfan speed regulator, electronic suitable for single phase AC, 240 volts, 50 Hz,100 watts, complete all as specified and as directed by Engineer-in-Charge 75 Supply and fix ceiling fan suitable for working on AC 230 volts, 50 Hz,1200 mm sweep 5 star rating with down rod and canopy colour of milky white including suitable fan hook anchor flashner for fixing of fan on ceiling complete all as specified and as directed. 76 Supply and fix energy efficient aluminium housing LED batten 22 watt fitting 4ft in length nano diffuser technology to ensure minimum loss in light transmitted, long life of over 30000 hours includinglamp and connecting with twin core shethed cable from fitting to ceiling rose all as specified and as diected. 77 Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant complete with IP 65/66 protection complete all as specified and directed. 78 Supply and fix in repair metal enclosure distribution board SPN, 8 way 240 volts, with 200 amps rated bus bar, with IP 42 protection and double door, suitable for mounting MCBs complete all as as specified and as directed by Engineer-in-Charge 79 Supply and fix MCB single pole, 240 volts, 5 to 32 Amps, all as specified and as directed. 80 Supply and fix MCB SPN 240 volts, 5 to 32 Amps,B series all as specified and as directed. 81 M&L for earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6mm thick buried directly in ground ( earth pit not less than 2.25 M deep below ground level) with top edge of the plate not less than 1.5 Meter below normal ground level connected to GI wire 4 mm dia by means of bolts, nuts , check nuts and washers of GI and GI tubing 20 mm bore light grade for earth lead protection up to main earth test point and including concrete pit in PCC (1:3:6) type C1 pre cast RCC (1:2:4) type B1 cover slab 54 x 54 x 5 cm with one handle for lifting made out of 8 mm dia MS bar, wire mesh, 20 mm bore GI tubing (LG) for watering, charcoal or coal and salt in alternate layers including excavation earth work complete all as specified and directed electrical plate No. 3 of SSR part - I 82 Supply, lay, test and commissioning under ground XLPE insulated and PVC sheathed, armoured heavy duty under ground cable, suitable for earthed system, laying in trenches/duct sleeving through pipe in duct, ISI marked with aluminiumstranded conductor 1100 volt grade of cross section area 2 Core 10 sq mm. 83 Supply & lay cable protection pipe of HDPE double wall corrugated (DWC) incl couplers,bends etc of size 50 mm OD and ID 38mm confirming to IS 14930 -II and ISI Marked all specified and directed. 84 S&F tube light grade galvanised with all fittings laid in trenches of following size.(a)50 mm bore 85 Material and Labour for cutting bituminous road at a width not more than 30cm and a depth not exceeding 60 cm for laying of pipes on road crossing for cable protection and making goodwith cement concrete 1:2:4, type, B-2 to match the existing surfaces of the road all as specified and as directed by Engineer in charge.
