Tender For Provision Of Store Ceremonial Items; 1.00 Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5 m in depth and getting out in hard/dense soil . 2.00 Returning ,filling in ,including spreading ,levelling,watering and well ramming in layers not exceeding 25cm in hard dense soil. 3.00 Removing surplus excavated soil to a distance exceeding 5 km but not exceeding 15 km and depositing where directed 4.00 Plain cement concrete 1:4:8 type D2 using 40 mm graded stone aggregate as in foundations ,fillling and mass concrete. 5.00 M&L for RCC design mix M-25 (20mm graded aggregate) in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete 6.00 M&L for flat formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surfaces of concrete. 7.00 M&L for TMT bars 10 mm dia over cut to length,bent to shape required ,including cranking ,bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia. 8.00 All as above, but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders 9.00 Precast cement concrete block masonry with solid blocks exc 10 cm in width in PCC 1:2:4 type B-1 and setting in cement mortar 1:4 all as specified 10.00 Providing precast cement concrete solid building blocks or slabs 10cm thick (with plain or interlocking joints as directed) , in walls in PCC 1:2:4 type B-1 and setting in cement mortar 1:4 all as specified 11.00 M&L for Roof trusses(framed), trussed, purlins, crane gantries, rails, fastenings and heacy bracketbframing(Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to Fe410-W (Gde-E-250 quality A). 12.00 M & L for preparing new steel and iron surfaces of any description over 10 cm in width or girth, priming with red oxide and applying two coats of synthetic enamel paint over a coat of red oxide primer 13.00 S&F pre painted gavalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screrws as specified. 14.00 S&F Anodised aluminium snap grid frame work for false ceiling allas specified 15.00 Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified 16.00 Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions 17.00 M&L for Rendering with WPC in CM 1:4, 15mm thick on othe than fair faces of brick work or concrete surfaces all as specified and directed. Note : WPC shall be measured and paid separately 18.00 Supply only Intergral waterproofing compound 19.00 M & L prepaeation newly plastered of wall surfaces and applying two coats of acrylic smooth exterior paint of required shade (applied @ 1.67ltr/10 Sqm) over and including priming coat of exterior primer @2.20 Kg/10 Sqm) all as specified . 20.00 M & L for Non-skid coloured ceramic tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.06 Sqm but exceeding 0.11 Sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface all as specified and as directed by Engr-in-charge.. 21.00 M & L Glazed coloured ceramic tiles in vertical surface 350x250x7mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface all as specified and as directed by Engr-in-charge.. 22.00 M&L for Rendering in CM 1:6, 10mm thick on fair faces of brick work or concrete surfaces all as specified and directed. 23.00 M & L prepation of newly plastered wall surfaces and applying two coats of distemper oil- emulsion over a coat of primer over 3mm thick wall care putty on wall on wall all as specified and as directed . 24.00 Granite (of any type) tiles 20mm thick machine cut, bedded andjointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete 25.00 M&L for Screed bed or bedding layer of mortor 15 mm thick in CM 1:6 for laying floor finishes all as specified and directed. 26.00 M&L for Cement concrete type D- 2, 1:4:8 (40mm graded aggregate) in sub base of floor 27.00 M&L for Rendering 10mm thick on fair faces of brick work or concrete surfaces with CM 1:4 as in backing coat of skirting /dado all as specified and directed. 28.00 M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp- ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall not be paid for separately). 29.00 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 30.00 S&F 100mm long, Butt hinges, extruded brass, with brass hinge pin, bright polished and fixed, type B-11 all as specified and as directed. 31.00 S&F 300mm Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed. 32.00 S&F 200mm long Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed. 33.00 S & F Floor door stopper of brass body and tongue with hard drawn steel spring 34.00 S&F Aluminium (extruded section) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851to 1000 mm in width and of weight between 61 to 80 kg and fixed 35.00 S & F Solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S square tube, suplying and fixing in opening as per specification and drawing etc complete all as specified. 36.00 S & F Factory made solid PVC Moulded door shutter with wood EPS, 30mm thick , with 2,4, or 6 raised panel design with 2mm thick moulded prelaminated PVC Sheet on both faces supplying & fixing in the frame at site as per specification & drawing etc complete all as specified and as directed by Engineer-in-Charge. 37.00 S&F 75 mm long butt hinges, type C-22 extruded aluminium anodised with brass hinge pin, anodised and fixed and all as specified and directed 38.00 S&F 100mm long Aluminium anodised barrel towers bolts of extruded section and all as specified and directed 39.00 S&F 150mm extruded aluminium alloy handles, fabricated type anodised as specified and directed 40.00 S&F vitreous china wash down water closet pan (Pedestal pattern), white including seat cover complete all as per specified and as directed by Engineer-in-Charge.Make :- Jaquar Model No OPS-WHT-7753S250UFPMZ or equivalent 41.00 S& F Vitreous China urinal including brackets complete all as specifed and directed. Make : Jaquar Model No -URS-WHT-13261 or equivalent. 42.00 S& F Vitreous China wash basin, white, flat back including brackets and pedestal complete all as specifed and directed. Make : Jaquar Model No QPS-WHT-7803PM (WHB) & QPS-WHT-7303PM (Pedestal) or equivalent. 43.00 S&F 32mm CP brass waste coupling 130mm high complete all as specified and directed. Make : - Jaquar Model No ALD -709L130 or equivalent 44.00 S&F two way Bib taps, brass chromium plated fancy type with wall flange screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore all as per specified.Make:- Jaquar Model No VGP-81041 or equivalent 45.00 S&F Bib taps, brass chromium plated fancy type with wall flange screwed down, screwed for iron pipe or for brass ferrule and fixed for 15mm bore all as per specified.Make:- Jaquar Model No VGP-81037 or equivalent 46.00 S&F chromium plated health faucet with hand held and spring operated control valve with PVC flexible pipe connection of suitable length,wall hook all as directed fixed to 15 mm bore pipe. Make :- Jaquar model No ALD-573. 47.00 Supply and application of single component, seamless, spray applied, hybrid elastomeric PU based material i.e Nitoproof 725 of Fosroc chemicals (or) sikalastic 590 of Sika India Pvt Ltd (or) equivalent in any approved make as approved by GE over a coat of primer i.e Nitoproof WB primer of Fosroc chemicals (or) diluted sikalastic 590 of Sika India Pvt Ltd (or) equivalent in any approved make as approved by GE, all as recommended by manufacturer ans as specified.Note:-(i) Average minimum DFTof PU based material shall be 1mm and shall be applied by using a Graco pump.(ii) PU based material shall process the following properties solids by volume -65%, tensile strength ASTM D412-1.75Mpa, density 1.3 g/ml, elongation ASTM D-412-350%, Adhesion to substrate concrete-1.9Mpa, resistance to water-10m pressure.(iii) Rate are deemed to be include for cleaning and preparation of surface to receive PU water proofing system including filling of cracks with cementitious repair mortars i.e renderoc CS of Fosrock chemicals (or) equivalent of approved make.(iv) 10 years of guarantee shall be provided. 48.00 M&L for concealed Point wiring one light point controlled by one, one way switch complete with 1.5 sqmm single core PVC insulted FRLS cable 1100 volts grade multistranded copper conductor drawn through in and including 20mm dia PVC rigid non metallic conduit concealed with all accessories such as internal bend, end caps etc complete concealed in walls and surface in ceiling/roof/etc including 1.5 Sqmm single core PVC insulated FRLS cable 1100 volts grade with multistranded copper conductor cable as earth continuity conductor including fabricated branded modular metal flush box concealed in walls with suitable modular plate with cover with suitable screws for housing switches, socket outlets, fan regulators etc all as specified and as directed. Note : Cutting chases and making good in wall / floor will be Measured and paid seperately. 49.00 All as per item No 85 herein before but one ceiling/exhaust fan point controlled by one, one way switch. 50.00 All as per item No 85 herein before but one switch socket outlet point 5 Amps on independent board. 51.00 S&F Switch Modular 6A single pole, one way, 1 module complete all as specified and as directed. 52.00 S&F Modular white cover plate with frame 3 module 53.00 All as per item No 90 herein before but 6 module 54.00 S&F socket Modular 6/16A 2/3 pin combined 2 module complete all as specified and as directed. 55.00 S&F flush box 3 module 56.00 All as per item No 93 herein before but 6 module 57.00 Supply and fixing LED lights fitting 1 x 22W, 220V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. 58.00 Supply and fix MCB DB, SPN, 4 ways, double door, 240 volt, Isolated neutral bar with IP54 protection, door earthing arrangement with cement spill protector, mechanical impact strength IK09 complete. Make: L&T/Legrand/ Havells 59.00 Supply and fix MCB SP 6 to 32 Amps, 240Volts, 10 KA, B Curve complete. Make: L&T/Legrand/ Havells 60.00 Supply and fixing SPN 32 Amp rating 240 V, 10 KA C curve miniature circuit breaker (MCB) complete. Make: L&T/Legrand/ Havells 61.00 Supply and fix ceiling rose surface type bakelite 65 x 50mm with three terminals. 62.00 M & L Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of the earth plate at a depth not less than 1.5 M below ground level, earth plate surrounded by 15cm thick and packed with layers of charcoal dust and common salt , earth lead GI wire 4mm dia ( 8 SWG) connectd to GI earth plate elcectrode by means of bolts, nuts, check nuts, washers of galvanised iron, thimbles and other end of earth wire connected to main switch board/ feedar pillar and protected by galvanised iron pipe medium grade 15mm bore and 20mm bore medium grade GI pipe with funnel and wire mesh for watering including necessary excavation and earth works. PCC Chamber in cement concrete 1:2:4 type B-1 & RCC cover and all as shown in Electrical Plate No. 3 of SSR ( Part-I) of 2009. (i) The unit rate includes earthing wire, and protection pipe upto 7.5 metre. 63.00 M& L for making opening for fixing of Exhaust fan of size 300 mm sweep complete and making good the disturbed surface complete. 64.00 Supply and fix exhaust fan, steel bodyAC single Phase. 230V of size 300msweep with, blades, and frame andlouvers 65.00 Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; andcutting chases for concealed water tubing or concealed conduit wiring,etc., and making good, cutting not exc 10 cm girth 66.00 Removing excavated materials (soils) to a distance not exc 50m and depositing where directed at a level not exc. 1.5 m above the starting point 67.00 M&L for riddled earth filling in trenches above and below the cable as in cable protection. Note:- Punned thickness shall be mesured and paid. 68.00 Material and Labour in replacement for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, multi stranded, 1100 volts grade, cross-sectional area 10 Sqmm, 2 core with and including making connection by using necessary thimbles complete all as specified and directed 69.00 Supply and laid well burnt bricks sub-class B designation 75 for cable protection, brick shall be laid dry flat as width of brick eqals to the length of cable and the gap between two adjacent brick shall not exceeded 10 mm, complete all as specified and as directed. 70.00 Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft loose soil. 71.00 Providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratorycompaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete
