As As To Main Gate At Ins Satavahana And Provision Of Three Vermi Pits And One Refuse Bin At Dolphin Hill Under Ge(Nb) Visakhapatnam; 1 Dismantling framed trusses n exe 10 m span complete all as specified and directed. 2 Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed. 3 Dismantling Plain or corrugated steel sheeting,of any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed 4 Dismantling structural steel work including doors, gates etc complete all as specified and directed. 5 Demolition of brick work or stone / boulder masonry, built in cement mortar including all quoins, pillars etc and disposal of debris and rubbish outside MD land as directed by the Engr-in-Charge. 6 Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for and disposal of debris and rubbish outside MD land complete all as directed by the Engr-in-Charge. 7 Surface dressing n exc 15 cm deep as in soft/loose soil complete all as specified and directed. 8 Surface excavation n. exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed. 9 Surface excavation n. exc 30 cm deep and averaging 15 cm deep and getting out in soft/disintegrated rock complete all as specified and directed. 10 Rough excavation not exceeding 1.5 m deep and getting out in soft/disintegrated rock complete all as specified and directed. 11 Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in hard and dense soil complete all as specified and directed. 12 Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in soft/disintegrated rock complete all as specified and directed. 13 M&L for Plain Cement Concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed. 14 Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in hard and dense soil complete all as specified and directed. 15 Removing excavated materials exc 1.5 Km but n. exc 5 Km and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed. 16 M&L for reinforced cement concrete M-30 (Design Mix) using 20mm graded stone aggregate as in foundation, plinth beams, bases of columns and mass concrete complete all as specified and directed by Engineer-in-Charge. 17 M&L for reinforced cement concrete M-30 (Design Mix) using 20mm graded stone aggregate as in Columns, pillars, piers, posts and struts etc. complete all as specified and directed by Engineer-in-Charge. 18 M&L for reinforced cement concrete M-30 (Design Mix) using 20mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, desk slabs and in shelves. complete all as specified and directed by Engineer-in-Charge. 19 Use and waste of form work to formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed by Engineer-in-Charge.. 20 Use and waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work n exc 200 mm thick ( horozontal or slopping) for rough finished surface flat or curved of concrete complete all as specified and directed by Engineer-in-Charge. 21 Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions flat or curved of concrete complete all as specified and directed by Engineer-in-Charge. 22 S & F high strength corrosion resistant TMT steel bars 10 mm dia., and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed. 23 S & F high strength corrosion resistant TMT bars 5mm dia and over upto and including 10mm dia in strirrups, spacers and binders spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified and directed. 24 M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed. 25 M & L for Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed. 26 M & L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished the surfaces even and smooth without using extra cement complete all as specified and directed. 27 M & L for 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed. 28 M & L for designer Chequered cement concrete tiles of size 30cm x 30cm x 23-25mm thick, as in floors etc, including 15 mm thick screed bed in cement mortar 1:6 and set & jointed in neat cement slurry and pointed in grey cement and pigments to match with the shade of tiles complete all as specified and directed. 29 S&F Mild steel rag or lewis bolts,25 mm dia of neck, screwed one end,with hexagonal or square nuts and washers, theother end enlarged andjagged or lewised, exc 30cm long complete all as specified and as directed.. 30 S & F rolled mild plates (plain or chequered) channels, square cut or notched, forming holes with riveted, bolted or welded attachment conforming to Fe 410W Gr E-250, quality-A complete all as specified and directed. 31 S & F MS steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161-1979 grade St-240 complete all as speicfied and directed. 32 M&L for rolled mild steel work conforming to Fe 410 -W (Gde E- 250)quality A as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed. 33 M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc primer complete all as specified and as directed.. 34 S & F Pre-Painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instruction complete all as specified and directed. 35 S&F pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges , valley gutter etc fixed with self tapping screws complete all as specified and directed. 36 M & L for Mild Steel Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing (fencing post) including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 ® complete all as specified and directed. 37 S&F for 3-4 mm thick plain/designed coloured Aluminum Composite Panel Sheet for wall cladding/Roofing/Paneling upto 5 mtr height including necessary aluminium frame work, fittings & fixtures, including necessary scaffolding work, complete all as specified and directed. 38 S & F 0.71mm thick Plain Aluminium sheeting Alloy 31000 H4 in stepped flashing (measured as the minimum rectangle from which the pieces can be cut) complete all as specified and directed. 39 S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 160mm bore including necessary bracket,clamp etc complete all as specified and directed. 40 S&F PVC (SWR) bends any radius 160mm bore complete all as specified and directed. 41 S & F bold metallic stainless steel letters or alphabetes made out of 22 Guage thick Stainless steel plain sheet of grade 304 plain sheet of suitable width not less than 50mm and depth/thick not less than 20mm based on height of letter (hollow section made to shape by using computerised cutting), height of letter not less than 15 inch in Hindi and Engilish laguages and fixed on granite/MS/ACP wall cladding/tiles finished wall elevated from surface complete all as specified and as directed. 42 S&F 1.25 mm Mild steel, plain or corrugated, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or weldedseams, including bending or turning up, mitred angles, etc complete all as specified and as directed. 43 M&L for preparation of new platered surface of wall and applying two coats of weather proof exterior acrylic emulsion paint having dart pick up resistant,silicon enhanced,UV resistant and PU enhanced property over a coat of alkali resistant primer including all necessary saffolding, complete all as specified and directed. Note :- Painting work shall be carried out acoording to Smart Painting procedure mentioned in PS 44 M & L for 18 to 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 15 mm thick screed bed in cement mortor 1:6 & cutting, polishing complete all as specified and directed. 45 M & L for framed work with ornamental and intricate design of gate, grills,gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; for portions framed and hung as gates, including pintle hinges, stops,hand-made sliding bolts, etc and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. 46 M & L for Precast Reinforced Cement Concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings.kneelers, apex stones, pier caps,columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders and set in cement mortar 1:4 including necessary form, moulds, etc complete all as specified and directed by the Engr-in-Charge. (Note : Reinforcement shall be measured and paid separately) 47 Material and labour for 150 mm thick (spread thickness) soling or sub base with broken boulders or quarried stone, interstices filled, surface formed and rolled with 8 to 10 tonne power roller and consolidated to required gradient and camber complete all as specified and as directed by the Engineer-in-Charge. 48 Material and labour for 150mm thick (Compacted thickness) in two equal layer WBM, with coarse aggregates (Granite, Basalt or Trap stone) of grading 2 (63mm to 40mm size) or of grading 3(50 to 20mm size) spread, roller and consolidated to gradient and camber required using 8-10 ton capacity mechanical power roller complete all as specified & directed. 49 M & L for framed work such as grills,gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; for portions framed and hung as gates, including pintle hinges, stops,hand-made sliding bolts, etc and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. 50 M & L for plain cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) for embedding holdfast, in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating as directed complete all as specified and directed. 51 S & F three core, PVC insulated, unsheathed, multistranded copper flexible conductor cable, 1100 vols grade ISI marked of size 1.5 sqmm complete all as specified and as directed. 52 S&F LED floodlight 180W 230V AC made up of pressure die cast aluminium housing with toughened glass and high power LEDs and secondary lenses with IP66 protection including necessary connection with copper conductor flexible wire/cable complete all as specified.Make : Model No LFLN-180-CDL/60-M of Crompton or equivalent model of make list as given in PS as approved by GE 53 S&F energy saving ,environment friendly RGBW prjector light consisting of highly efficent LEDs as light sources , 50 watt, 240 V AC ,system lumens 2500 lm with IP 67 protection ,suitable LED driver with APFC,over voltage and surge protection up to 10 Kw with SPD including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Make:- Havells Cat No XPERIAFLS50WLEDDMX25DTOLTGWHT or its equivalent make of Philips / CG 54 S&F flexible led strips light with uniform light distribution 24 W 6500 K,IP 65 protection including 12 V 2 A Driver for constant voltage complete all as specified and directed Make:- Havells Cat No LHEHDLP7UN1W024 for LED strip light and model no LHFXBGNNIN1W024 for driver or its equivalent make of Philips / CG 55 S & F DMX controller UE 11 for LED projector light complete all as specified and as directed. (Make: Havells cat part No.LSSLOG0178 or equivalent make as per List of Manufacturers) 56 S & F DMX signal amplifier 4 pin M12 for LED projector light complete all as specified and as directed. (Make: Havells cat part No. LSSLOWOO770 or equivalent make as per List of Manufacturers mentioned in PS) 57 S & F universal address writer for LED projector light complete all as specified and as directed. (Make: Havells cat part No. LSSLOB0346 or equivalent make as per List of Manufacturers mentioned in PS) 58 S & F universal DMX extension cable 4 pin for LED projector light complete all as specified and as directed. (Make: Havells cat part No. LSSLOB0366 /67or equivalent make as per List of Manufacturers mentioned in PS) 59 S & F DMX male/female supply cable 4 pin for LED projector light complete all as specified and as directed. (Make: Havells cat part No. LSSLOB0365 /68 or equivalent make as per List of Manufacturers mentioned in PS) 60 Supply, fixing thermoplastic circuit breaker boxes 1 row 4 modules with IP 65 protection and necessary fixing arrangements complete all as specified and as directed Make: Hensel cat part No. KV 7104 or equivalent make as per List of Manufacturers mentioned in PS) 61 Supply, fixing, commissioning and testing in repairs MCB SP 6 to 32 Amps, 240 Volts, 10KA, C Curve, complete all as specified and as directed (Make: Havells cat part No. DHMGCSPF006-032 or equivalent make as per List of Manufacturers mentioned in PS) 62 Programing of LED projector light through company approved qualified enginner/ technician complete all as per direction of Engr-in charge. Note : Engineer/Technicain shall be of same company of aprroved LED spot light. (ii) LED spot light and connected accessories will be measured and paid under item no 54 and 55 to 59 63 S&F LED aluminium profile casing of size 15.8x15.8 mm having colour RGBW complete all as specifed and directed. Make : Make as approved shall be of ISI marked and in case there is no BIS certification system/ Indian standard for the product, these shall be certified by accredited (NABL) laboratories to confirm to other standard of repute ,like British / European /American Standards (ii) Product shall have minimum 02 years manufacturer warranenty. (iii) Contractor shall submit 02 year written guarantee againt any manufacturing defect. 64 S&F rigid non-metalic PVC conduit ,20 mm dia exclusive of boxes but inclusive of all tees,bends,elbows,reducers,bell mouth tube ends and fixing accessories such as couplers,lock nuts,saddles,pipe hooks etc complete all as specified and directed. 65 S & F voltage stabilizer of capacity 4 KVA, single phase, input working voltage 170-270 Volts, metal body with time delay system, wall mountable, built in thermal overload protection, low & high voltage cut-off protection, micro controller based design complete all as specified and directed. Make: V-Gaurd model no VG-400 or equivalent model of make mentioned in PS
