Supply, Delivery And Installation Of Electro-Mechanical Equipments And Other Allied Works At Pansuli Head Works Site Under Improvement Of Rcfa Part-Iii(Zone-I) Water Supply Scheme Under Asansol Mechnical Division, P.H.E. Dte.-- 1 Supply, Delivery and storage at site of Vertical Turbine Pumping Machinary with Bowl Assembly, Line Shaft, Column Pipe, Discharge Head, Sole Plate & Other Accessories etc. having the Discharge-150 M³/Hour, Head-50 Mtr, vertical flange Mounted Induction Motor (IE 3 type)suitable for the pump duty mentioned above with adequate margin as per detail technical specification, No load as well as short-circuit Test Certificate of induction motor during test run has to be submitted during the delivery. 2 Supply,delivery and storage at site of following dia CI Single Door Swing Check N.R.V as per IS : 5312,Part-I,PN-1.0. 3 200 mm dia NRV.(FOR DELIVERY SIDE OF CLEAR WATER PUMP) 4 Supply, delivery and storage at site of follwing dia manually operated CIDF Rising type Sluice Valve as per IS:14846 PN-1.0. (Test Certificate, Waranty certificate to be submitted for each valve at the time of delivery) 5 200 mm dia.(FOR DELIVERY SIDE OF CLEAR WATER PUMP+COMMON HEADER OF CLEAR WATER PUMP) 6 Supply, delivery and storage at site of following diaCast Iron kinetic double orifice air released valve as per relevant IS, PN-1.0. 7 80 mm diaP.N-1.0.(CLEAR WATER) 8 Supply,delivery and storage at site offollowing dia. MS Dismantling joints with Rubber compression Ring and adjustable follower flanged complete assembled unit with galvanized stud and nuts PN-1.6. 9 200 mm dia Dismantling Joint PN-1.0. ( AT DELIVERY SIDE + COMMON HEADER OF CLEAR WATER PUMP) 10 Supply, delivery and storage at site offollowing 150mm dia Glycerine filled Diaphragm Seal type Gagues with syphon tube and three way cock. (Make - Approved Make) 11 Pressure Gauges (0-15 kg/ cm2)(2 NOS FOR DELIVERY SIDE+ONE FOR COMMON HEADER OF CLEAR WATER PUMP) 12 Supply, Delivery and Storage at site of 200 mm, MS black Pipes (For delivery common header, individual DeliveryPump under sl no 1 along with necessaryBends, fittings viz. flanges, bolts, nuts, gaskets, as reqd. to make the installation complete in all respect. 13 Supply of 1.5 MT capacity straight monorail arrangement of 6.0 mtr long incorporate with 2 M.T. capacity Indef-M brand Triple spur gear chain pulley Block with suitable gear traveling trolley having 5 mtrs lift. The Monorail beam shall be supported with 3(three) Nos. goal post having 3 mtrs. apart. Total hight of the goal post = 6.0 Mtrs. from floor level.The monorail designed as per IS 800, IS : 807 and IS : 3832 suitable for outdoor operation. 14 Supply, Delivery and Storage at Site 2 mm. thick CRCA Sheet Steel Enclosed Cubical type Indoor Floor Mounted415 Volt PDB cum MCCPanelhaving required Feeders.(Extension of Panel) 15 Supply & delivery of Full Bore type Electro-Magnatic Flow Meter with meter protection panel as well as Cable between Sensor and Transmitter on Delivery Rising main line. 16 200mm dia delivery main line. 17 Supply, Delivery and storage at site 3 core 1.1 KV Grade following Al. Ar.XLPE insulated Cable. 18 3 CoreX 50 Sqmm cable.(For MCC Panel to individual clear water Induction Motor.) 19 Earthing & lightning protection arrangement for Pump house and electrical installation as per ISS and IE rules.(Earth Pit 3 Nos) 20 Supply, delivery at site and storage of GI perforated cable tray at Pump house for laying of incoming & outgoing power and control cables to and from MCC Panelhaving proper M.S. structural support as per specification and direction of EIC. 21 Installation of all items as mentioned in Sl.No. 1 to 13excluding Item No-12 including lowering of VT Pump into the CWR, pipe supports, valve supports, flow meter installation, H.O.T installation, laying of cables with necessary jointing materials, earthing arrangement of motors, starters,including supply of all erection items viz. rubber gaskets, nuts & bolts etc., including cost ofwelding etc. as required for complete installationas per Hydraulic standard & IE rules in compliance. 22 Painting of the installation (viz. crane, pumps frame ,valves, pipe lines etc.by two coats of epoxy paint (colour to be decided by EIC) over a coat of primer. 23 Testing & Commissioning of the entire installation i.e. Pumps, Motors,valves etc.as per direction and to the entire satisfaction of E.I.C.
