Tender For CONVERSION OF CHC KARAKULAM TO BFHC AT THIRUVANANTHAPURAM- 1 CIVIL WORKS 2 15.7.4Demolishing brick work manually / by mechanical means including stacking of serviceable material anddisposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.Incement mortar 3 14.1.2Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq meters and under, includingcutting the patch in proper shape, raking out joints and preparing and plastering the surface of the wallscomplete, including disposal of rubbish to the dumping ground within 50 meters lead:Cement mortar 1:4 (1 cement: 4 coarse sand) 4 2.6.1Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas(exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds ofsoil 5 4.1.8Providing and laying in position cement concrete of specified grade excluding the cost of centering andshuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40nominal size) 6 7.1.1 Random rubble masonry with hard stone in foundation and plinth including levelling up with cementconcrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinthlevel with:Cement mortar 1:6 (1 cement : 6 coarse sand) 7 2.25Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers notexceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 mand lift up to 1.5 m 8 50.6.5.2 Hollow block masonry using pre cast blocks ( Factory made) of size 40x20x15cm or nearest available size confirming to IS 2185 part 1 of 1979 for super structure up to floor two level with thickness 15cm in: CM 1:6 ( 1 cement : 6 coarse sand ) etc complete 9 13.7.212 mm cement plaster finished with a floating coat of neat cement of mix:1:4 ( 1 cement : 4 fine sand) 10 13.1.112 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) 11 9.48.2Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square orround bars etc. including priming coat with approved steel primer all complete.Fixed to openings/ woodenframes with rawl plugs screws etc 12 od84303/2024_2025supplying and fixing weld mesh grill using 5 mm MS rod to the existing angle iron frame work including alllabour charges cost of materials and applying two coat iron primer etc complete 13 13.80Providing and applying white cement based putty of average thickness 1 mm, of approved brand andmanufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 14 13.43.1Applying one coat of water thinnable cement primer of approved brand and manufacture on wallsurface:Water thinnable cement primer 15 13.60.1Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Twoor more coats on new work 16 13.46.1Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied@ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) 17 13.61.1Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two ormore coats on new work 18 13.99.1Painting with synthetic enamel paint of approved brand and manufacture ofrequired colour to give aneven shade :One or more coats on old work 19 10.1Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer all complete. 20 12.50Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation asapproved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 gramsper sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet andpolyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum toavoid scratches during transportation and should be supplied in single length upto 12 metre or as desiredby Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm)with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost ofpurlins, rafters and trusses and including cutting to size and shape wherever required. 21 12.4.2Providing ridges or hips width 60 cm overall width plain G.S. sheet fixed with polymer coated J or Lhooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.0.63 mm thick with zinc coating not less than 275 gm/m2 22 21.1.1.2Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built upstandard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS :733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up thegaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc.Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically whereverrequired including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steelscrews, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing,paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium(minimum thickness of powder coating 50 micron) 23 21.2.2Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded woodparticle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windowsshutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architecturaldrawings and directions of Engineer - in- Charge.Pre- laminated particle board with decorative laminationon both sides 24 21.3.2Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDMrubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer -in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50mm thickness 25 21.10Providing and fixing double glazed hermetically sealed glazing in aluminium window, ventilators andpartition etc. with 6 mm thick clear float glass both side, having 12 mm air gap, including providing EPDMgasket, perforated aluminium spacers, desiccants, sealant (Both primary and secondary sealant ) etc. asper specifications, drawings and direction of Engineer-in-Charge complete 26 od87301/2024_2025Providing and fixing brass roller set for sliding door including all labour charges and cost of materials etc complete 27 21.12.2Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0mm thick & 2100 mm long withS.S. screws etc. complete as per direction of Engineer -in-Charge.Powder coated minimum thickness 50micron aluminium tubular handle bar 28 21.13Providing and fixing 100 mm brass locks ( best make of approved quality ) for aluminium doors includingnecessary cutting and making good etc. complete 29 9.95.3Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc.complete:100x75x4 mm 30 9.97.5Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC10 as per : 1868), transparent or dyed to required colour or shade, with necessary screwscomplete:100x10 mm 31 9.84Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (havingbrand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door widthform 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc.complete. 32 9.123Providing and fixing factory made door frame (single rebate) made out of single piece extruded solid PVCfoam profile with homogeneous fine cellular structure having smooth outer integral skin having 62 mmwidth & 32 mm thickness, frame will be mitred & jointed with self driven self tapping screws of size 38 mmx 4 mm & PVC solvent cement, including fixing the frame to wall with suitable dia & length anchorfastener as per manufacturers specification and direction of Engineer-in-charge. 33 9.124.1Providing and fixing factory made 30 mm thick door shutter made of solid PVC foam profile. The styles &rails shall be of size 75 mm x 30 mm having wall thickness 5 mm. The styles, top & bottom rails shallhave one side wall thickness of 15 mm integrally extruded on the hinge side of the profile for better screwholding power. The styles and rails shall be reinforced with M.S. tubes of size 33 mm x 17 mm x 1 mm,painted with primer, all four corners of reinforcement to be welded or sealed. Solid PVC extruded bidding(Push fit type) will be set inside the styles and the rails with a cavity, to receive single piece extruded 5mm PVC sheet as panel. The styles and rails will be mitred cut and joint with the help of PVC solventcement & self driven self tapping screws. Single piece extruded solid PVC lock rails of sixe 100mm x 30mm with wall thickness 5 mm & 15 mm integrally extruded in the middle of the lock rail & fixed with styles with the help of PVC solvent cement & self driven self tapping screws of size 100 mm x 8 mm completeas per manufacturers specifications and direction of Engineer -in-charge.Non decorative finish 34 11.37Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by themanufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours such as White, Ivory,Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), includingpointing the joints with white cement and matching pigment etc., complete. 35 8.31Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622(thickness to be specifiedby the manufacturer), of approved make, in all colours,shades except burgundy, bottle green, black ofany size as approved by Engineerin-Charge,in skirting, risers of steps and dados, over 12 mm thick bedof cementmortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @3.3kg per sqm,including pointing in white cement mixed with pigment of matchingshade complete. 36 11.41.2Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer)with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the jointswith white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm. 37 od84413/2024_2025Precast Eurocon tiles 12 mm thick with graded marble chips of size upto 12mm, laid in floors, andlandings, jointed with neat cement slurry mixed with pigment to match the shade of the tiles includingrubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand): Ordinary cement without any pigment 38 10.28Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc.,including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting thesame with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessaryaccessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of thefloor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (forpayment purpose only weight of stainless steel members shall be considered excluding fixingaccessories such as nuts, bolts, fasteners etc.) 39 od85382/2024_2025Supplying and fixing Stainless Steel Grab Bar, Wall Mounted Safety Straight Grab Bar for bathroom 40 PLUMBINGWORKS 41 17.3.2Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mmflush bend, overflow arrangement with specials of standard make and mosquito proof coupling ofapproved municipal design complete, including painting of fittings and brackets, cutting and making goodthe walls and floors wherever required :W.c. pan with ISI marked black solid plastic seat and lid 42 17.7.2 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass wasteof standard pattern, including painting of fittings and brackets, cutting and making good the wallswherever require:White Vitreous China Wash basin size 630 x 450 mm with a single 15 mm C.P. brasspillar tap 43 18.51.1Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards andweighing not less than 690 gms.15 mm nominal bore 44 18.53.1Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved qualityconforming to IS: 893115 mm nominal bore 45 50.17.1.5Supplying and fixing CP Health Faucet superior quality ( Jagur or equvalent make ) including cost ofmaterials and labour charges etc complete as per the direction of site Engineer-in-charge 46 17.32.2Providing and fixing mirror of superior glass ( of approved quality) and of required shape and size withplastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangularshape 453x357 mm 47 17.28.1.1Providing and fixing P.V.C. waste pipe for sink or wash basin including PVC.waste fittings complete.Semirigid pipe32 mm dia 48 od87072/2024_2025Supplying and fixing 20 mm water connection pipe etc complete 49 17.73.2Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screwswith concealed fitting arrangement of approved quality and colour600 mm long towel rail with total lengthof 645 mm, width 78 mm and effective height of 88 mm, weighting not less than 190 gms 50 18.65Providing and fixing PTMT Soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mmwith concealed fittings arrangements, weighing not less than 106 gms 51 od88332/2024_2025Providing and fixing 150mm silt with CP gratings 52 50.18.8.2.2Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. Thisincludes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete asper direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the walletc. 20 mm pipe 10 Kgf/ cm2 53 50.18.8.3.2Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. Thisincludes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete asper direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the walletc. 25 mm pipe 10kgf /cm2 54 50.18.8.4.1Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. Thisincludes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete asper direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the walletc. 32 mm pipe 10Kgf/cm2 55 50.18.8.6.1Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. Thisincludes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete asper direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the walletc. 50 mm pipe 10 kgf/cm2 56 50.18.8.9.1Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. Thisincludes jointing of pipes with one step PVC solvent cement and testing of joints complete as perdirection of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc.110 mm pipe 6kgf/cm2 57 50.18.9.22.1Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Elbow 58 50.18.9.22.4Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVCsolvent cement- 110 mm dia Bend 59 50.18.9.22.5Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with PVCsolvent cement 110x110x110 mm dia Tee 60 50.18.9.22.6Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes, including jointing with PVCsolvent cement - 110x110x110 mm dia Door tee 61 od84407/2024_2025Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVCsolvent cement - 50mm dia Elbow 62 od84408/2024_2025Providing and fixing PVC moulded fittings /accessories for Rigid PVC pipes, including jointing with PVCsolvent cement - 50 mm dia Door Elbow 63 od88295/2024_2025Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVCsolvent cement - 50mm dia Bend 64 od88296/2024_2025Supply and fixing 1 1/2 PVC valve and other accessories 65 18.48Providing and placing on terrace (at all floor levels) polyethylene water storage tank :ISI 12701 marked,with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank 66 ELECTRICALWORKS 67 1.10.3Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVCinsulatedcopper conductor single core cable in surface / recessed medium class PVC conduit,with modular switch,modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLSPVC insulated copperconductor single core cable etc as required.Group C 68 1.14.2Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulatedcopper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5sq. mm + 1 X 2.5 sq. mm earth wire 69 1.14.3Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulatedcopper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 4sq. mm + 1 X 4 sq. mm earth wire 70 1.14.4Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulatedcopper conductor, single core cable in surface / recessed medium class PVC conduit as required2 X 6Sq.mm + 1 x 6 sq.mm earth wire 71 1.24.3Supplying and fixing following modular switch/ socket on the existing modular plate & switch boxincluding connections but excluding modular plate etc. as required.15/16 amp switch 72 1.24.5Supplying and fixing following modular switch/ socket on the existing modular plate & switch boxincluding connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet 73 1.27.2Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modularswitches in recess etc as required.3 Module (100mmX75mm) 74 1.28.2Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. asrequired.3 Module 75 2.3.3Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V,on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar,interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator12way, Double door 76 2.9.5Supplying and fixing following way prewired vertical type TP&N MCB distribution board of steel sheet for415 volts on surface/ recess complete with loose wire box of sheet steel, dustprotected, duly powderpainted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar formounting MCBs, terminal connectors for all incoming and outgoing circuits, duly prewired with adequatesize of FRLS PVC insulated copper conductor upto theterminal connector/ neutral link, earthing etc asrequired (But without MCB/ RCCB/ Isolator).(Note : Prewired vertical type MCB TPDB is normally usedwhere 3 phase outlets are required.)4 way Double door 77 2.10.1Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, C curve, miniature circuit breakersuitable for inductive load of following poles in the existing MCB DB complete with connections, testingand commissioning etc. as required.Single pole 78 2.13.2Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete withconnections, testing and commissioning etc. as required.63 amps 79 2.10.4Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, C curve, miniature circuit breakersuitable for inductive load of following poles in the existing MCB DB complete with connections, testingand commissioning etc. as required.Triple pole 80 2.13.1Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete withconnections, testing and commissioning etc. as required.40 amps 81 2.15.3Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual currentcircuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete withconnections, testing and commissioning etc. as required.63 amps 82 1.26Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modularplate as required 83 od88379/2024_2025Supply, installation, testing and commissioning of wall mounted Three Phase 4 wire Energy meter withpoly carbonate body having range of 10-63A, with enclosure made out of powder coated 16 SWG CRCAsheet suitable for fixing in surface/recess with 3 nos. of 63A HRC fuses,63A TPN isolator,neutral link, itsinter connections etc.The enclosure shall have lockable door with glass window and all mountingaccessories etc. complete as required (supply of energy meter is under KSEB scope). 84 od88380/2024_2025Supplying and fixing single tube set ( electronics) and other accessories 85 od88381/2024_2025Supplying and fixing 48 Ceiling fan and other accessories 86 1.25Supplying and fixing two module stepped type electronic fan regulator on the existing modular plateswitch box including connections but excluding modular plate etc. as required 87 od88382/2024_2025Supplying and fixing 9 exhaust fan and other accessories 88 od88383/2024_2025Supplying and fixing angle batten with LED bulb and other accessories 89 od92757/2024_2025Supplying and fixing 50 watt LED Top light with arm including all labour charges cost of materials etccomplete 90 od92758/2024_2025Supplying and fixing bulk head with 23 Watts LED and other acessories 91 od95100/2024_2025Electric connection taken from KSEB including cash deposit etc complete 92 NETWORKING WORKS 93 od93147/2024_2025Providing network cabling using cat 6 cable through 1 case and caping and giving conncetion includingall labour charges materialcost,grimping and connecting etc, complete 94 od93468/2024_2025Supplying and fixing 12U rack and giving connection 95 od93469/2024_2025Supplying fixing roset box and grimping the ends etc.complete 96 od93470/2024_2025Supplying and fixing PATCH CORD 0.50M on bottom and grimping two ends 97 od93471/2024_2025Supplying and fixing PATCH CORD 0.50M on top and grimping two ends 98 od93472/2024_2025Supplying and fixing 1M PATCH CORD and grimping two ends 99 od94690/2024_2025Supplying and fixing 2M PATCH CORD and grimping two ends 100 od94759/2024_2025Supplying and fixing 3M PATCH CORD and grimping two ends 101 od94691/2024_2025Supplying and fixing patch pamel and giving cvonnection 102 od94870/2024_2025Supplying and fixing 8 port switch and giving connection 103 od94871/2024_2025Supplying and fixing RJ 45 Connection clip 104 od94872/2024_2025Engaged a computer engineer for programming all network and commisioning etc. complete (1 Racks X2000 = 2000)
