Tender For Up gradation Of Fountain In Shaheedi Park At Dam Site.; 1 Dismantling concrete Cement concrete plain 1:3:6 mix CSR 8.6© 2 Earth work in excavation of foundations of bridges culverts, building including handling of material with a combined lead of 15 meters dressing of bed and sides stacking the excavated soil from the edge of excavation and subsequent filling around :- For hard clayey soil or hard conglomerate or semi-rocky type of the nature of pick jumper with occasional blasting. CSR 6.7(c) 3 Compacting original ground below EmbankmentLoosening, leveling and compacting original ground below embankment to facilitate placement of first layer of embankment, scarified to a depth of 150 mm, mixed with water at OMC and then compacted by rolling so as to achieve minimum dry density as given in Table 300-2 for embankment construction as per technical clause 305 of MORT&H specifications. CSR 24.4(b) 4 Cement concrete 1:3:6 With stone ballast or shingle Mixing by mechanical means using concrete mixer volumetric type CSR 10.12(a)(ii) 5 Reinforced cement concrete M-25 mechanically batch mixed using batch type concrete mixer as per IS:1791 and vibrated by needle vibrator but excluding steel reinforcement centering and shuttering in foundation and plinth CSR 10.16 6 Cold twisted detormed (Ribbed/Tor Steel) Bars (Fe 500 grade as per IS 1786-2008), for R.C.C works, where not including in the complete rate of RCC including bending and binding placing in position complete. CSR 18.18 7 Centering and shuttering for colums (circular or curved in plain) CSR 9.5 8 Squared rubble masonry uncoursed or built to courses in foundation and plinth in cement mortar 1:5 to a pattern if specified. CSR 12.22 9 Fine ashlar in cement mortar (1:3) upto 6 meters above plinth level. CSR 12.1 10 Cement concrete 1:8:16 With stone aggregates 20mm in gauge Mixing by mechanical means using concrete mixer volumetric type CSR 10.7(b)(ii) 11 Cement concrete 1:4:8 With stone ballast 20mm gauge Mixing by mechanical means using concrete mixer volumetric type CSR 10.11( 12 Providing and laying 50mm thick factory made cement concrete interlocking paver block of M-30 grade machine made rubber moulded smooth finish with strong vibratory process or with vibrohydraulic compaction machine and of approved size and design/shape laid in Ordinary Grey and pattern over and including 40mm thick compacted bed of coarse sand, filling the joints with fine sand etc, all complete as per directions of Engineer-in-Charge for non traffic areas and streets having width less than 3.05 mt. (Also not to used over footoaths) CSR 14.136 13 Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20mm x 20mm x 4 mm in alcolour design, fixing in customize design as per direction of Engineer-in-Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, Material and required pattern approved by Engineer-In-Charge. CSR 14.146 14 Providing and laying machine cut, mirror polished, Italian Marble stone flooring laid in required pattern in linear portion of the building all complete as per architectural drawings, with 18mm thick stone slab laid over 20mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand ) laid and jointed with white cement slurry @4.4 kg/sqm including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 18mm thick Italian Marble stone slab, Perlato, Rosso Verona, Fire Red or Dark Emperadore etc. CSR 14.144(a) 15 Providing and laying, jointing , fixing, testing ISI Marked G.I Pipe (as per IS 1239 ) B-Class, including cost of Specials such as tees, bends, sockets elbow etc., cutting, threading and testing in trenches in the ground complete 80mm i/d CSR 28.36(h) 16 Providing, fixing and jointing ISI Marked Gun-Metal peet valves (Heavy Pattern) as per IS 778 with hand wheels, on G.I Pipe lines laid in the ground or inside buildings including all carriages complete. 80mm i/d Gun Metal peet valve heavy pattern CSR 28.43(h) 17 Providing, fixing and jointing G.I Union Couplings (of approved make with the approval EIC) as per IS 1879 in G.I. Pipe lines complete in all respect. 80mm i/d GI Union CSR 28.40(h) 18 Structural steel work in angles tees, flats, riveted, including cutting, fixing all gusset plates, bolts, nuts, rivets etc. with hoisting and erecting in position.For roof truss, well curbs, plate girders etc. of any span for building for bridges upto 15M span. CSR 18.3(a) 19 Design, Supply, Installation, Fixing, testing, Commissioning of 5 HP Mono Submersible Pump Sets with Steel Mounting Frame, grouting nut bolts, suction mesh cover of SS, etc (AOR) 20 Design, supply, installation, fixing, commissioning control panel (Indoor type) in sheet steeln paint finish enclosure with hinged front door, with provision for incoming & outgoing cable entry. Electric panel shall be protected against dust and jets of water per rating IP55 and shall have been tested and certified as such by Govt.of India Test Laboratory. Panel comprises of motor main switch, contractors, switch fuse, SPMCB, push button on off switches, indicating lamps, capacitor, step down transformer, Sequencer for LED Lights etc. complete with internal wiring. Panel to be placed within 6m from pool. (AOR) 21 Design, supply, installation, testing of 10mm GI manifold x 7m with support stands. (AOR) 22 Design, supply, installation of 3.8m and 1.8m dia aluminum ring made from non corrosive extruded aluminum alloy, 19 no. outlet, cascade jet, 19 no. cascade jet made of aluminum with gun metal control valve, ball joint, necessary upvc feeder pipe, support stands. (AOR) 23 Supply of 2.5 x 3 core cable for pump connection(AOR) 24 Supply of 1.5 x 4 core cable for light connection(AOR) 25 21w x 12v LED light, Waterproof luminaries with array of high output of LEDs housed in compact enclosure with elastomeric seal. Special polymide cable gland. Compact socket head fasteners and mounting bracket. The housing, top cover and bracket are in noryl construction, fasteners of stainless steel. (AOR) 26 PVC conduit pipe withNecessaryfittings. (AOR) 27 Supply, fixing, testingearthing electrode, earth pit cover, earthing material as per requirement.(AOR) 28 Supply, fixing of light mounting bracket, PVC joint box, cable jointing compound, nut bolts, washer nipples, brackets cable tie etc. (AOR) 29 Design, supply, installation, testing, commissioning of outdoor electrical enclosure fabricated from 18 gauge MS sheet with hinged front door, back wall mounting type with provision for incoming & outgoing cable entry, long legs made of iron angle with locking arrangements & provision for fixing of panel complete in all respect. (AOR) 30 Freight, loading, unloading, labour cess, insurance, civil work, supervision, on site warranty of one year, training to operator, manuals.(AOR)
