Tender For Quotation Fro Lift Irrigation Scheme With Solar Panel Material Supply And Installation, jamtara-Jharkhand

Quotation Fro Lift Irrigation Scheme With Solar Panel Material Supply And Installation--For 10 H.P. D.C.(PMSM/BLDC/SRM) Solar pump. Supplying Installation and Commissioning charge of Solar Module Mounting (Galvanised Steel) surface structure (for 50 kW) having Hot deep galvanised of Zinc thickness 80micron and as per IS4759 with C Channel & anti theft with nut bolt of grade SS304, which should also withstand high wind velocity upto 150km/hr or as per MNRE 1.03 50kWp SPV module of 330wP or higher rating, which must have Specification as per IS 14286/IEC 61215 The module must have to quilify IS/IEC 61730 part I & II (or having mechanical load test of 5400Pa) for safety purpose. Module to Module wattage mismatch in SPV Array shall be +/-3% and to qualify IEC TS 62804-2015 for the detection of potential induced degradation and warranted for output wattage not less than 90% in 10yrs and 80% at the end of 25yrs as per MNRE. Arrangement of Lightening Arrestor excluding Earthing for 50kW & 5 no. of 10HP DC Solar Pump. 1.04 1.05 Supplying installation and commissioning charge of Module and Structure for 50kW. 1.06 Maintenance for atleast 5 years or as per MNRE guidelines for 50kW SPV and 5 nos of 10HP Solar Pump with all accessories. 1.07 10 H.P D.C.(PMSM/BLDC/SRM) Solar pump set of having performance with respect to Total Head, Maximum Current, Capacity, Voltage Range etc as per MNRE guidelines. 1.08 SPV controller/VFD integrated with GPRS, having MPPT Protection IP 65 or above as per MNRE to run 10HP DC Solar pump 1.09 Array junction box (IP 65 or above) as per MNRE for 50 KW SPV 1.10 Misclianeous Accessories for Installation of 10H.P. D.C. Solar Pump 1.11 Solar cable 4 mm2 used as per IS 694 or as per MNRE. 1.02 2.01 Materials for water supply work. 2.02 4 dia M.S. pipe TATA (C-Class) 2.03 6 M.S. pipe TATA(C-Class) 2.04 10M.S. PipeTATA (C-Class) 2.05 4 dia G.I. Flange 6mm thick. (I.S.I. Standard) 2.06 4x 8/10 Reducer thickness 6mm(I.S.I. Standard) 2.07 10(250mm) M.S. Flange 6mm thick. (I.S.I. Standard) 2.08 10(250mm) M.S. bend 6mm thick (I.S.I. Standard) 2.09 4 M.S. Tee 6mm thick.(1.S.I. Standard) 2.10 4 PVC Tail piece. (I.S.I. Standard) 2.11 4 M.S. bend 6mm thick. (1.S.I. Standard) 2.12 4 M.S. Ball Valve(I.S.I. Standard) 2.13 4 dia G.I. pipe TATA (C-Class) 2.14 6 G.1. pipe TATA(C-Class) 2.15 10 G.I. PipeTATA (C-Class) 2.16 4 dia G.I. Flange 6mm thick. (I.S.I. Standard). 2.17 4x 8/10 G.I. Reducer thickness 6mm(I.S.I. Standard) 2.18 10 (250mm)G.I. Flange 6mm thick. (I.S.I. Standard) 2.19 10 (250mm) G.I. bend 6mm thick. (I.S.I. Standard) 2.20 4 G1. Tail piece. (I.S.I. Standard) 4 G.I. Ball Valve. (I.S.I. Standard) 2.21 2.22 4 D.I. Tee (I.S.I. Standard) 2.23 4 D.1. Tail piece. (I.S.I. Standard) 2.24 4 D.I. bend(I.S.I. Standard) 2.25 4 D.I. Ball Valve. (IS.I. Standard) 2.26 HDPE Fittings(Confirming IS 4984/14151/12788/13488) Suitable for HDPE pipe of Material grade-PE80-PN10. 2.27 HDPE TEE(Dia. in mm). hdpe end cap hdpe end cap, hdpe flange , hdpe dresser coupler, etc

Refer document

Refer document

Refer document