Renovation Of Dak Bunglow Inshan-- 1 Removing dry or oil bound distemper, water proofing cement paint and the like by crapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 2 Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 3 Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 meters lead :Of area of 3 sqm. and below 4 Providing and fixing brass curtain rods of wall thickness 1.25 mmwith two brass brackets fixed with brass screws and wooden plugs etc. wherever necessary complete. 25 mm diameter. 5 Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws Second class deodar wood 6 Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood) 7 Painting with synthetic enamel paint of approved brand and manufactureto give an even shade Two or more coats on new work 8 Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates andsimilar works. 9 Providing wood work in frames of doors, windows, clerestory windows andother frames, wrought framed and fixed in position with hold fast lugs or withdash fasteners of required dia and length (hold fast lugs or with dash fastenersshall be paid for separately): Sal wood 10 Providing and fixing panelled or panelled and glazed shutters for doors,windows and clerestory windows fixing with butt hinges of required size withnecessary screws, excluding panelling which will be paid for separately, allcomplete as per direction of Engineer-in-charge. (Note: -Butt hinges andnecessary screws shall be paid separately Second class deodar wood 11 Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40mm thick Second Class deodar wood 12 Providing and fixing M.S. grills of required pattern in frames of windows etc.with M.S. flats, square or round bars etc including priming coat with approvedsteel primer all complete. Fixed to openings / wooden frames with rawl plugs screws etc. 13 Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.1 mm thick 14 Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm over and including priming coat of exterior primer applied @ 2.20kg/10sqm) 15 Providing and fixing aluminum hanging floor door stopper, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. completeSingle rubber stopper 16 Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed torequired colour or shade with nuts and screws etc. complete : 17 300x16 mm 18 250x16 mm 19 Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed torequired colour or shade with nuts and screws etc. complete : 20 150x10 mm 21 100x10 mm 22 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades,laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 600x600 mm 23 Providing corrugated G. S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I limpet washers or with G.I. limpet washers filledithwhite lead,including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, raftersand trusses and including cutting to size and shape wherever required 0.63 mm thick with zinc coating not less than 275 gram/m2 24 Providing and fixing 12 mm thick flat pressed 3 layer medium density particle board or graded particle board (Grade I) IS: 3087 marked, in ceiling with necessary nails etc. complete (frame work to be paid separately) : 25 Providing wood work in frames of false ceiling, partitions etc. sawn and fixed inposition Budloo / Fir wood 26 Providing and fixing plain lining tongued and grooved, including wooden plugs completewith necessary screws and priming coat on unexposed surface Second class Deodar Wood 27 Providing and fixing plained eaves boarding 2nd class kail wood250x32 mm (nominal size ) 28 French spirit polishing, Two or more coats on new works including a coat of wood filler 29 Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular ppropriate sectionsand other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides withrequired EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanicallywherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing,panelling and dash fasteners to be paid for separately.)Powder coated aluminum (minimum thickness of powdercoated 50 microns 30 Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular ppropriate sectionsand other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides withrequired EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanicallywherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing,panelling and dash fasteners to be paid for separately.)For shutters of doors, windows & ventilators includingproviding and fixing hinges / pivots and making provision for fixing offittings wherever required including the cost of EPDM rubber / neoprenegasket required (Fittings shall be paid for separately.) 31 Providing and fixing 12mm thick prelaminated particle board flatpressed three layer or graded wood particle board (conforming to IS:12823 Grade-I type-II) in panelling fixed in aluminum doors, windowsshutters and partition frames with C.P. brass / stainless steel screws etc.complete as per architectural drawings and directions of engineer-incharge. Pre-laminated particle board with decorative lamination on bothsides. 32 Providing and fixing glazing in aluminum door, window, ventilatorshutters and partitions etc. with EPDM rubber / neoprene gasket etc.complete as per the architectural drawings and the directions of engineerin-charge. (Cost of aluminum snap beading shall be paid in basic item.)With float glass panes of 5.0 mm thickness (weight not lessthan 12.50 kg / sqm) 33 Providing and fixing wash basin with C.I. brackets, 15mm C.P. brasspillar taps, 32 mm C.P. brass waste of standard pattern, includingpainting of fittings and brackets, cutting and making good the wallswherever required : White Vitreous China Wash basin size 630x450 mm with a pairof 15 mm C.P. brass pillar taps. 34 Providing and fixing CP Brass 32mm size Bottle Trap of approvedquality & make and as per the direction of Engineer-in-charge. 35 Providing and fixing P.V.C. waste pipe for sink or wash basin includingP.V.C waste fittings complete:Semi rigid pipe.40 mm dia. 36 Providing and fixing 600x450 mm beveled edge mirror of superior glass(of approved quality) complete with 6 mm thick hard board ground fixedto wooden cleats with C.P. brass screws and washers complete. 37 Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge.Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc. 38 PN-16 pipe, 16mm OD(SDR-7.4) 39 PN-16 pipe , 20mm OD(SDR-7.4) 40 PN-16 pipe , 25mm OD(SDR-7.4) 41 External work including trenching, refilling etc. 42 PN-16 pipe, 16mm OD(SDR-7.4) 43 PN-16 pipe , 20mm OD(SDR-7.4) 44 PN-16 pipe , 25mm OD(SDR-7.4) 45 Providing and fixing PPR Unions 46 PPR Union 20mm 47 PPR Union 25mm 48 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the wallswherever required : Kitchen sink with drain board510x1040mm bowl depth 250mm 49 Providing and fixing 15 mm nominal bore C.P. stop cock (concealed) of standard design and of approved make conforming to IS : 8931 50 Providing and fixing uplasticized PVC connection pipe with brass unions 30 cm length15 mm nominal bore 51 Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931 52 Providing and fixing 15 mm nominal bore C.P. brass long nose bib cockof approved quality conforming to IS standards and weighing not less than 810 gms. 53 Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete 54 125x65x2.12 mm 55 100x58x1.90 mm 56 75x47x1.70 mm 57 Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primerM.S. tube 58 Providing and fixing soil, waste and vent pipes : 100 mm dia. Sand cast iron S and S pipe as per IS:1729 59 Providing and fixing powder coated telescopic drawer channels 300mm long with necessary screws etc. complete as per directions of engineer-in-charge 60 Providing and fixing sliding arrangement in racks/cupboards/cabinets shutter bywith stainless steel rollers to run inside C or E aluminum channel section (the payment for C or E channel shall be made separately) 61 Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed withmatching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing toedges to give high gloss finish etc. complete at all levels(Area of slab over 0.5 sqm) 62 Providing and fixing 25mm thick shutters for cupboard etc, including nickel plated bright finished M.S. piano hinges with necessary screws. Paneled or paneled and glazed shutters:1st class teak wood 63 Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. 64 Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. 65 125 mm 66 100 mm 67 75 mm 68 Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction ofEngineer-in-charge :econd class deodar wood 69 Providing and fixing Mild Steel hooks and eyes(LMR) 70 Carriage of Steel at an avg distance 100 km by MT 200 mtr by HL 71 Carriage of CGI Sheet at an avg distance 100km by MT 200 mtr by HL
